Age | Commit message (Collapse) | Author | Files | Lines |
|
When configuring a port, prox configures queue flags.
For historitical reasons, offloads had to be disabled on
some pmds.
There is now an API to query the ports and gets their
capabilities. This fix sets now the flags based on the capabilities,
and not the driver name.
Change-Id: Ic72d15001992f26910f653c70d31e4381fff8089
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
Jumbo frames are now supported through the addition of a "mtu"
parameter of the port in the config file.
Setting the mtu to a value higher than 1500 bytes will enable
the reception of jumbo frames.
In addition, the rte_eth_dev_set_mtu is now set for all pmds.
Finally, setting mbuf_size does not set MEMPOOL_F_NO_SPREAD
anymore. This option was only used for pure debugging.
Big packets can be received using two ways
- Using multiple "small" mbufs, i.e. around 2K. This is the default.
- Using one big mbuf holding the whole packet. This can be enabled
by setting a parameter mbuf_size in the receiving core configuration
Change-Id: Idd60ad31f41c89f9522dff4d894af2696b7a2ea1
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
This adds support for tasks in l3 submode receiving from ports but
transmitting to rings.
ARP related information is exchanged between tasks through master core.
Tasks transmitting to physical ports are responsible to transmit arp
related packets. Tasks not transmitting to physical ports (and using
rings) should not try to transmit arp packets. Transmitting arp
packets through ring would be more complex, as we would need extra information
(within the mbuf) to distinguish for instance an arp reply comoing from the
network and an arp reply coming from a core (as a reply to an arp request).
Change-Id: Ib55dc8c39d5e55703a933faa16bcc008f1274929
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
The l3 submode was not supported in nop mode, as the nop mode uses some
specific nop thread (and not generic). When L3 is specified, the nop mode
must use the generic thread. In addition the l3 submode is implemented
differently than other submodes. It is not supported through task_init
structures (i.e. each task does not have to explicitely tell that it
supports l3 submode). But this prevented to run both a nop with no submode
and a nop with a l3 submode. Note that nop with l3 is usually not very useful
- it handles arp (requests and response) but as nop, it does not swap IP
addresses. So with a real switch, the packets transmitted will be received
back... and l3 mode is usually mainly usefull when using a switch.
However, there is at least one nop mode where l3 submode makes sense:
when the nop does not transmit. In such cases, for instace used in
conjunction with a gen l3, the nop receives all packets and forward
the arp requests and responses to the master for handling.
Change-Id: I992121db285ba25a11cbb494092a6afc6fe55a58
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
Change-Id: Ie6d4e7ce22c27967117a446626f5923643397812
Signed-off-by: Patrice Buriez <patrice.buriez@intel.com>
|
|
JIRA: SAMPLEVNF-55
PROX is a DPDK-based application implementing Telco use-cases such as
a simplified BRAS/BNG, light-weight AFTR... It also allows configuring
finer grained network functions like QoS, Routing, load-balancing...
(We are moving PROX version v039 to sampleVNF
https://01.org/intel-data-plane-performance-demonstrators/prox-overview)
Change-Id: Ia3cb02cf0e49ac5596e922c197ff7e010293d033
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
|