| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Multicast can be enabled through configuration or through command line
- Through configuration
Add multicast=mcast_address (e.g. multicast=01:00:5e:01:02:03) in the port
section
- Through command line
run enable multicast port_id mcast_address (e.g. enable multicast 1 01:00:5e:01:02:03)
IGMP join message is sent unsollicited through command line:
join igmp core_id task_id ip (e.g. join igmp 1 0 224.1.1.3)
To enable swap answering IGMP Query (w/ IGMP Join)
- Through configuration
Add igmp ipv4=ip_address within the core/task section
- Through command line
join igmp core_id task_id ip (e.g. join igmp 1 0 224.1.1.3)
(this will 1st initiate an unsollicated join, then answer any subsequent query)
UDP/TCP packets received on a multicast address (224.0.0.0 => 239.255.255.255) are discarded
To stop sending responses to IGMP query:
leave igmp core_id task_id
Change-Id: I3808ccabf3b38b5a1e10e1b044db63aa05bcd7b5
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
mbuf size was setup to achieve the best performance i.e.
using the smallest mbuf and not segmenting packets.
However this resulted in complex code, much dependent of the way
the pmd are working e.g. a change(fix) in recent dpdk i40e
implementation caused a 1782 (=1518+8+256) bytes mbuf to be too
small to hold a 1518 bytes packets.
Hence this change simplifies the mbuf size selection at the price
of a potential decreases in performance - as more memory is now used.
Except if jumbo frames are used, the mbuf size will now be the same
for all modes. The packets will not be segmented except if jumbo
frames are enabled.
If jumbo frames are enabled, packets are by default segmented, except
if the mbuf size is configured big enough in the config file.
Change-Id: I222fcac7a65c0d221d5d422f419deb9c0f864172
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
|
|
L2fwd and swap has many options to set src mac. swap was supposed
to support the ability to use port mac, but config file parsing was
wrong. L2fwd was using port mac if a port was available and if
src mac=packet or if there was no src mac in the config.
Now l2fwd supports the following options
- "src mac=xx:xx:xx:xx:xx:xx" => this mac address is used as src mac.
- "src mac=packet" => the src mac is taken from the dst mac of the
received packet.
- "src mac=hw" => the src mac is taken from the mac address of the port,
if there is a physical port. Error otherwise.
- "src mac=no" => src mac kept untouched
- No "src mac" => same as "src mac=hw" if there is a physical port
and same as "src mac=packet" otherwise.
Default is (no "src mac") hence the mac is taken from the tx port if there
is one tx port and from the packet otherwise.
swap support is similar, except that it does not support "src mac=no".
Change-Id: I70fe49a61c2e85772288b769ede14a7a6205d122
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
Change-Id: Ie6d4e7ce22c27967117a446626f5923643397812
Signed-off-by: Patrice Buriez <patrice.buriez@intel.com>
|
|
JIRA: SAMPLEVNF-55
PROX is a DPDK-based application implementing Telco use-cases such as
a simplified BRAS/BNG, light-weight AFTR... It also allows configuring
finer grained network functions like QoS, Routing, load-balancing...
(We are moving PROX version v039 to sampleVNF
https://01.org/intel-data-plane-performance-demonstrators/prox-overview)
Change-Id: Ia3cb02cf0e49ac5596e922c197ff7e010293d033
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
|
Xavier Simonart
Patrice Buriez
Deepak S