| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In Prox configuration IMIX can be specified using the following syntax:
imix=pkt_size,pkt_size... Up to 127 different pkt sizes can be specified.
Through command line, the following syntax can be used
imix core_id task_id pkt_size,pkt_size... Up to 127 packet sizes can be specified.
When IMIX is enabled, PROX will loop through the list of packet sizes.
PROX supports two different submodes to handle pcap files.
In the 1st submode (default, no submode specified), timestamps from
the pcap file are ignored. In this submode IMIX is supported as well and each
packets in the pcap file will be generated with all IMIX sizes.
In the second submode, called pcap in gen mode, packets are generated at
the timestamp specified in the pcap file. This submode does not support IMIX.
Change-Id: I53cbf1378a5364254285b81e6848350d98561184
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
This commit adds support for the creation of tap devices.
To create a tap device, and associate it with a DPDK port,
add within the port section:
vdev=<tap_name>
local ipv4=<ip_assigned_to_port>
<tap_name> will appear as a kernel network device, with an IP <ip_assigned_to_port>
ARP packets received from the network on the DPDK interface will be forwarded to the kernel.
1st packet which needs to be generated to a new IP will cause an IP packet
to be sent to the kernel (using socket sendto) forcing the kernel to send an ARP_REQUEST.
In this commit, there is no notification from the kernel about ARP table changes.
This is subject to further commits.
Two config files, gen_tap.cfg and swap_tap.cfg have been created. They work one against each other.
*** Note however that they do not work if running within the same host
(with the port being connected back to back) ***
This is due to the fact that the kernel would bypass the ports and use local interface...
Change-Id: Iadeec0d99e3c693472ea44bdb9163a3bf97df2fa
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
This commit prepares PROX for supporting changes from DPDK 19.08
Mainly, the "sed" listed below were run.
In addition,
- some forward definition have been removed,
- prox_compat.h has been updated
- prox_compat.h has been included where necessary.
Hence such a commit is rather easy to review and to reapply
on other branches if necessary.
sed -i 's/struct ether_hdr/prox_rte_ether_hdr/g' *.h
sed -i 's/struct ether_hdr/prox_rte_ether_hdr/g' *.c
sed -i 's/struct ether_addr/prox_rte_ether_addr/g' *.c
sed -i 's/struct ether_addr/prox_rte_ether_addr/g' *.h
sed -i 's/prox_rte_ether_addr_port/struct ether_addr_port/g' *.c
sed -i 's/prox_rte_ether_addr_port/struct ether_addr_port/g' *.h
sed -i 's/struct vlan_hdr/prox_rte_vlan_hdr/g' *.c
sed -i 's/struct vlan_hdr/prox_rte_vlan_hdr/g' *.h
sed -i 's/struct ipv4_hdr/prox_rte_ipv4_hdr/g' *.h
sed -i 's/struct ipv4_hdr/prox_rte_ipv4_hdr/g' *.c
sed -i 's/struct ipv6_hdr/prox_rte_ipv6_hdr/g' *.c
sed -i 's/struct ipv6_hdr/prox_rte_ipv6_hdr/g' *.h
sed -i 's/struct udp_hdr/prox_rte_udp_hdr/g' *.c
sed -i 's/struct udp_hdr/prox_rte_udp_hdr/g' *.h
sed -i 's/struct tcp_hdr/prox_rte_tcp_hdr/g' *.c
sed -i 's/struct tcp_hdr/prox_rte_tcp_hdr/g' *.h
sed -i 's/struct prox_rte_ether_addr_copy/ether_addr_copy/g' *.c
sed -i 's/struct prox_rte_ether_addr_copy/ether_addr_copy/g' *.h
sed -i 's/struct prox_rte_ether_addr_copy/prox_rte_ether_addr_copy/g' *.c
sed -i 's/struct prox_rte_ether_addr_copy/ether_addr_copy/g' *.h
sed -i 's/prox_rte_ether_addr_copy/ether_addr_copy/g' *.h
sed -i 's/prox_rte_ether_addr_copy/ether_addr_copy/g' *.c
sed -i 's/ether_addr_copy/prox_rte_ether_addr_copy/g' *.c
sed -i 's/ether_addr_copy/prox_rte_ether_addr_copy/g' *.h
sed -i 's/prox_rte_ether_hdr_arp/struct ether_hdr_arp/g' *.h
sed -i 's/prox_rte_ether_hdr_arp/struct ether_hdr_arp/g' *.c
sed -i 's/struct vxlan_gpe_hdr/prox_rte_vxlan_gpe_hdr/g' *.h
sed -i 's/struct vxlan_gpe_hdr/prox_rte_vxlan_gpe_hdr/g' *.c
sed -i 's/eth_random_addr/prox_rte_eth_random_addr/g' *.c
sed -i 's/eth_random_addr/prox_rte_eth_random_addr/g' *.h
sed -i 's/ETHER_CRC_LEN/PROX_RTE_ETHER_CRC_LEN/g' *.c
sed -i 's/ETHER_CRC_LEN/PROX_RTE_ETHER_CRC_LEN/g' *.h
sed -i 's/ETHER_HDR_LEN/PROX_RTE_ETHER_HDR_LEN/g' *.c
sed -i 's/ETHER_HDR_LEN/PROX_RTE_ETHER_HDR_LEN/g' *.h
sed -i 's/ETHER_MAX_LEN/PROX_RTE_ETHER_MAX_LEN/g' *.c
sed -i 's/ETHER_MAX_LEN/PROX_RTE_ETHER_MAX_LEN/g' *.h
sed -i 's/ETHER_MIN_LEN/PROX_RTE_ETHER_MIN_LEN/g' *.c
sed -i 's/ETHER_MIN_LEN/PROX_RTE_ETHER_MIN_LEN/g' *.h
sed -i 's/TCP_SYN_FLAG/PROX_RTE_TCP_SYN_FLAG/g' *.c
sed -i 's/TCP_RST_FLAG/PROX_RTE_TCP_RST_FLAG/g' *.c
sed -i 's/TCP_FIN_FLAG/PROX_RTE_TCP_FIN_FLAG/g' *.c
sed -i 's/TCP_ACK_FLAG/PROX_RTE_TCP_ACK_FLAG/g' *.c
Change-Id: I4dfe8be68e618c94dcaae28754579fbeb571bb00
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
mbuf size was setup to achieve the best performance i.e.
using the smallest mbuf and not segmenting packets.
However this resulted in complex code, much dependent of the way
the pmd are working e.g. a change(fix) in recent dpdk i40e
implementation caused a 1782 (=1518+8+256) bytes mbuf to be too
small to hold a 1518 bytes packets.
Hence this change simplifies the mbuf size selection at the price
of a potential decreases in performance - as more memory is now used.
Except if jumbo frames are used, the mbuf size will now be the same
for all modes. The packets will not be segmented except if jumbo
frames are enabled.
If jumbo frames are enabled, packets are by default segmented, except
if the mbuf size is configured big enough in the config file.
Change-Id: I222fcac7a65c0d221d5d422f419deb9c0f864172
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
|
|
Add support for pkt_inline of jumbo frames.
Dump the whole packet, and not a truncated packet. This might
have a small impact on performance as the memory footprint
is increased (by ~640K * number of tasks), resulting in potential
higher DTLB misses.
Change-Id: I4ed02be7ca899db4f8f97355c180a92d69d39d8f
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
Change-Id: Ie6d4e7ce22c27967117a446626f5923643397812
Signed-off-by: Patrice Buriez <patrice.buriez@intel.com>
|
|
JIRA: SAMPLEVNF-55
PROX is a DPDK-based application implementing Telco use-cases such as
a simplified BRAS/BNG, light-weight AFTR... It also allows configuring
finer grained network functions like QoS, Routing, load-balancing...
(We are moving PROX version v039 to sampleVNF
https://01.org/intel-data-plane-performance-demonstrators/prox-overview)
Change-Id: Ia3cb02cf0e49ac5596e922c197ff7e010293d033
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
|
Xavier Simonart
Patrice Buriez
Deepak S