| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
JIRA: YARDSTICK-1220
Implemented new "multi port stats <port list>" command, which returns a
semi-colon-separated list of comma-separated values:
- port id
- total (at last_tsc) for rx_pkts, tx_pkts, no_mbufs, ierrors + imissed
- last_tsc
Change-Id: I8a8da79cb4ccb245ccb38b50b561da51a40a359d
Signed-off-by: Patrice Buriez <patrice.buriez@intel.com>
|
|
|
|
When doing latency measurements PROX takes into account the
generation or reception of a bulk of packets. For instance, if
PROX receives at time T 4 packets, it knows that the first
packet was received by te NIC before T (the time to receive the other
3 packets, as they were received at maximum link speed).
So the latency data is decreased by the minimum time to receive those
3 packets.
For this PROX was using a default link speed of 10Gbps. This is wrong
for 1Gbps and 40Gbps networks, and was causing for instance issues
on 40 Gbps networks as extrapolating too much, resulting in either
too low latencies or negative numbers (visible as very high latencies).
Change-Id: I4e0f02e8383dd8d168ac50ecae37a05510ad08bc
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
irq mode can be used to show how a core is interrupted by other tasks.
This mode does not handle packets. It only loops reading tsc.
When the difference between two consecutive calls to rdtsc() is high
then it means the core was interrupted.
This task implementes the display, so that we can see a histogram of
interrupts as well as the maximum, per core.
Command line is also supported, through "show irq buckets" (too show
the intervals of each buckets, in micrcoseconds), and the stats
command line (showing the number of items in each buckets and the max)..
Change-Id: I153cc3deaa7b86ae2776ea44e46ef9ecfd116992
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
Command parser could have been crashing if a wrong core/task was
used in pkt_size command. For some other commands both an error
and a warning were printed in case of errors.
Change-Id: I6648bfca1b5bcde3c6393d49687ed84900326d49
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
The l3 submode was not supported in nop mode, as the nop mode uses some
specific nop thread (and not generic). When L3 is specified, the nop mode
must use the generic thread. In addition the l3 submode is implemented
differently than other submodes. It is not supported through task_init
structures (i.e. each task does not have to explicitely tell that it
supports l3 submode). But this prevented to run both a nop with no submode
and a nop with a l3 submode. Note that nop with l3 is usually not very useful
- it handles arp (requests and response) but as nop, it does not swap IP
addresses. So with a real switch, the packets transmitted will be received
back... and l3 mode is usually mainly usefull when using a switch.
However, there is at least one nop mode where l3 submode makes sense:
when the nop does not transmit. In such cases, for instace used in
conjunction with a gen l3, the nop receives all packets and forward
the arp requests and responses to the master for handling.
Change-Id: I992121db285ba25a11cbb494092a6afc6fe55a58
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
Change-Id: I9c46b57f98b566efc8ca3ea5966befe2a150315b
Signed-off-by: Xavier Simonart <xavier.simonart@intel.com>
|
|
Change-Id: Ie6d4e7ce22c27967117a446626f5923643397812
Signed-off-by: Patrice Buriez <patrice.buriez@intel.com>
|
|
JIRA: SAMPLEVNF-55
PROX is a DPDK-based application implementing Telco use-cases such as
a simplified BRAS/BNG, light-weight AFTR... It also allows configuring
finer grained network functions like QoS, Routing, load-balancing...
(We are moving PROX version v039 to sampleVNF
https://01.org/intel-data-plane-performance-demonstrators/prox-overview)
Change-Id: Ia3cb02cf0e49ac5596e922c197ff7e010293d033
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
|
Patrice Buriez
Deepak S
Xavier Simonart