1 files changed, 137 insertions, 0 deletions
diff --git a/VNFs/DPPD-PROX/config/bng-ovs-usv-4ports.cfg b/VNFs/DPPD-PROX/config/bng-ovs-usv-4ports.cfg
new file mode 100644
index 00000000..48321c0d
--- /dev/null
+++ b/VNFs/DPPD-PROX/config/bng-ovs-usv-4ports.cfg
@@ -0,0 +1,137 @@
+;;
+;; Copyright (c) 2010-2017 Intel Corporation
+;;
+;; Licensed under the Apache License, Version 2.0 (the "License");
+;; you may not use this file except in compliance with the License.
+;; You may obtain a copy of the License at
+;;
+;;     http://www.apache.org/licenses/LICENSE-2.0
+;;
+;; Unless required by applicable law or agreed to in writing, software
+;; distributed under the License is distributed on an "AS IS" BASIS,
+;; WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+;; See the License for the specific language governing permissions and
+;; limitations under the License.
+;;
+
+;;
+; This configuration is provided for virtualized environments running on top of
+; a soft-switch. Specifically, ingredients are Open vSwitch (openvswitch.org)
+; and Qemu version 1.6.2. Note that since the currently supported version of
+; Open vSwitch does not handle all the protocols that are used in the full BNG,
+; PROX has to be recompiled to use different packet processing paths as a
+; workaround. DPDK version 1.8.0 should be used with this configuration and it
+; has to be compiled with COMBINE_LIBS enabled:
+;   make install T=$RTE_TARGET CONFIG_RTE_BUILD_COMBINE_LIBS=y CONFIG_RTE_LIBRTE_VHOST=y
+; The following commands demonstrate how to set up Open vSwitch:
+;   git clone https://github.com/openvswitch/ovs.git
+;   cd ovs
+;   git checkout 5c62a855c7bb24424cbe7ec48ecf2f128db8b102
+;   ./boot.sh && ./configure --with-dpdk=$RTE_SDK/$RTE_TARGET --disable-ssl && make
+; This configuration is intended to be used in a VM with 4 virtual ports. This
+; means that 4 virtual ports (with type dpdkvhost) and 4 physical ports (with
+; type dpdk) will need to be added and connected through open-flow commands in
+; Open vSwitch. After Open vSwitch has been set up on the host, PROX needs to be
+; recompiled in the VM as follows before running it with this configuration:
+;   make BNG_QINQ=n MPLS_ROUTING=n
+;;
+
+[eal options]
+-n=4 ; force number of memory channels
+no-output=no ; disable DPDK debug output
+
+[port 0]
+name=cpe0
+mac=00:00:00:00:00:01
+[port 1]
+name=inet0
+mac=00:00:00:00:00:03
+[port 2]
+name=cpe1
+mac=00:00:00:00:00:02
+[port 3]
+name=inet1
+mac=00:00:00:00:00:04
+[variables]
+$wk=5s0,6s0
+
+[defaults]
+mempool size=16K
+[lua]
+lpm4 = dofile("ipv4.lua")
+user_table =dofile("user_table-65K-bng.lua")
+[global]
+start time=20
+name=BNG (OVS)
+
+[core 0s0]
+mode=master
+; IPv4
+;*****************************************************************************************
+;##### Load Balancing receiving from CPE and from Internet ####
+[core 1s0]
+name=LB-cpe
+task=0
+mode=nop
+rx ring=yes
+tx port=cpe0
+task=1
+mode=lbqinq
+rx port=cpe0
+tx cores=(${wk})t0 proto=ipv4
+
+[core 2s0]
+name=LB-inet
+task=0
+mode=nop
+rx ring=yes
+tx port=inet0
+task=1
+mode=lbnetwork
+rx port=inet0
+untag mpls=yes
+tx cores=(${wk})t1 proto=ipv4
+
+[core 3s0]
+name=LB-cpe
+task=0
+mode=nop
+rx ring=yes
+tx port=cpe1
+task=1
+mode=lbqinq
+rx port=cpe1
+tx cores=(${wk})t0 proto=ipv4
+
+[core 4s0]
+name=LB-inet
+task=0
+mode=nop
+rx ring=yes
+tx port=inet1
+task=1
+mode=lbnetwork
+untag mpls=yes
+rx port=inet1
+tx cores=(${wk})t1 proto=ipv4
+
+;*****************************************************************************************
+;#### Workers receiving from LB
+;#### Task 0: Upstream traffic
+;#### Task 1: Downstream traffic
+[core $wk]
+name=Worker
+task=0
+mode=qinqdecapv4
+rx ring=yes
+tx cores from routing table=2s0,4s0
+route table=lpm4
+local ipv4=21.22.23.24
+handle arp=no
+user table=user_table
+
+task=1
+mode=qinqencapv4
+rx ring=yes
+tx cores from cpe table=1s0,3s0 remap=cpe0,cpe1
+user table=user_table