diff options
Diffstat (limited to 'tools/pharos-validator/src/validation_tool/doc/network.yaml')
| -rw-r--r-- | tools/pharos-validator/src/validation_tool/doc/network.yaml | 221 |
1 files changed, 0 insertions, 221 deletions
diff --git a/tools/pharos-validator/src/validation_tool/doc/network.yaml b/tools/pharos-validator/src/validation_tool/doc/network.yaml deleted file mode 100644 index 705e8486..00000000 --- a/tools/pharos-validator/src/validation_tool/doc/network.yaml +++ /dev/null @@ -1,221 +0,0 @@ ---- -# This configuration file defines Network Environment for a -# Baremetal Deployment of OPNFV. It contains default values -# for 5 following networks: -# -# - admin -# - tenant* -# - external* -# - storage* -# - api* -# *) optional networks -# -# Optional networks will be consolidated with the admin network -# if not explicitly configured. -# -# See short description of the networks in the comments below. -# -# "admin" is the short name for Control Plane Network. -# During OPNFV deployment it is used for node provisioning which will require -# PXE booting as well as running a DHCP server on this network. Be sure to -# disable any other DHCP/TFTP server on this network. -# -# "tenant" is the network used for tenant traffic. -# -# "external" is the network which should have internet or external -# connectivity. External OpenStack networks will be configured to egress this -# network. There can be multiple external networks, but only one assigned as -# "public" which OpenStack public API's will register. -# -# "storage" is the network for storage I/O. -# -# "api" is an optional network for splitting out OpenStack service API -# communication. This should be used for IPv6 deployments. - -# yamllint disable rule:line-length -network-config-metadata: # Meta data for the network configuration - title: LF-POD-1 Network config # - version: 0.1 # - created: Mon Dec 28 2015 # - comment: None # - - -networks: # Network configurations - admin: # Admin configuration (pxe and jumpstart), - enabled: true - vlan: native # VLAN tag to use for Overcloud hosts on this network (Admin network is required to be native / untagged for PXE booting) - installer_vm: # Network settings for the Installer VM on admin network - nic_type: interface # Indicates if this VM will be bridged to an interface, or to a bond - members: - - em1 # Member Interface to bridge to for installer VM (use multiple values for bond) - vlan: native # VLAN tag to use for this network on Installer VM, native means none - ip: 192.0.2.1 # IP to assign to Installer VM on this network - usable_ip_range: 192.0.2.11,192.0.2.99 # Usable ip range, if empty entire range is usable, ex. 192.168.1.10,192.168.1.20 - gateway: 192.0.2.1 # Gateway (only needed when public_network is disabled) - cidr: 192.0.2.0/24 # Subnet in CIDR format 192.168.1.0/24 - dhcp_range: 192.0.2.2,192.0.2.10 # DHCP range for the admin network, if empty it will be automatically provisioned - dns-domain: opnfvlf.org # Admin network dns domain - dns-search: opnfvlf.org # Admin network dns-search domain - dns-upstream: # Admin network upstream dns servers - - 8.8.8.8 # - - 8.8.4.4 # - ntp-upstream: # Admin upstream ntp servers - - 0.se.pool.ntp.org # - - 1.se.pool.ntp.org # - nic_mapping: # Mapping of network configuration for Overcloud Nodes - compute: # Mapping for compute profile (nodes that will be used as Compute nodes) - phys_type: interface # Physical interface type (interface or bond) - vlan: native # VLAN tag to use with this NIC - members: # Physical NIC members of this mapping (Single value allowed for interface phys_type) - - eth1 - controller: # Mapping for controller profile (nodes that will be used as Controller nodes) - phys_type: bond - vlan: native - members: - - eth1 - - eth2 - - tenant: # Tenant network configuration - enabled: true - cidr: 11.0.0.0/24 # Subnet in CIDR format 192.168.1.0/24 - vlan: 10 # VLAN tag to use for Overcloud hosts on this network - mtu: 64000 # Tenant network MTU - overlay_id_range: 2,65535 # Tenant network Overlay segmentation ID range: VNI, VLAN-ID, etc. - - segmentation_type: vxlan # Tenant network segmentation type: vlan, vxlan, gre - - nic_mapping: # Mapping of network configuration for Overcloud Nodes - compute: # Mapping for compute profile (nodes that will be used as Compute nodes) - phys_type: interface # Physical interface type (interface or bond) - vlan: 10 # VLAN tag to use with this NIC - members: # Physical NIC members of this mapping (Single value allowed for interface phys_type) - - eth1 # Note, for Apex you may also use the logical nic name (found by nic order), such as "nic1" - controller: # Mapping for controller profile (nodes that will be used as Controller nodes) - phys_type: interface - vlan: 10 - members: - - eth1 # Note, for Apex you may also use the logical nic name (found by nic order), such as "nic1" - - external: # Can contain 1 or more external networks - - public: # "public" network will be the network the installer VM attaches to - enabled: true - vlan: native - mtu: 64000 # Public network MTU - installer_vm: # Network settings for the Installer VM on admin network (note only valid on 'public' external network) - nic_type: interface # Indicates if this VM will be bridged to an interface, or to a bond - members: - - em1 # Member Interface to bridge to for installer VM (use multiple values for bond) - ip: 192.168.37.12 # IP to assign to Installer VM on this network - cidr: 192.168.37.0/24 - gateway: 192.168.37.1 - floating_ip_range: 192.168.37.200,192.168.37.220 # Range to allocate to floating IPs for the public network with Neutron - usable_ip_range: 192.168.37.10,192.168.37.199 # Usable IP range on the public network, usually this is a shared subnet - dns_nameservers: # External dns servers - - 8.8.8.8 # - - 8.8.4.4 # - ntp: # External upstream NTP servers - - 0.se.pool.ntp.org # - - 1.se.pool.ntp.org # - syslog: # External Syslog server - server: 10.128.1.24 # - transport: 'tcp' # - nic_mapping: # Mapping of network configuration for Overcloud Nodes - compute: # Mapping for compute profile (nodes that will be used as Compute nodes) - phys_type: interface # Physical interface type (interface or bond) - vlan: 10 # VLAN tag to use with this NIC - members: # Physical NIC members of this mapping (Single value allowed for interface phys_type) - - eth1 - controller: # Mapping for controller profile (nodes that will be used as Controller nodes) - phys_type: interface - vlan: 10 - members: - - eth1 - external_overlay: # External network to be created in OpenStack by Services tenant - name: Public_internet - type: flat - gateway: 192.168.37.1 - - private_cloud: # another external network - enabled: false - vlan: 101 - mtu: 64000 - cidr: 192.168.38.0/24 - gateway: 192.168.38.1 - floating_ip_range: 192.168.38.200,192.168.38.220 # Range to allocate to floating IPs for the public network with Neutron - usable_ip_range: 192.168.38.10,192.168.38.199 # Usable IP range on the public network, usually this is a shared subnet - dns_nameservers: # External dns servers - - 8.8.8.8 # - - 8.8.4.4 # - ntp: # External upstream NTP servers - - 0.se.pool.ntp.org # - - 1.se.pool.ntp.org # - syslog: # External Syslog server - server: 10.128.1.24 # - transport: 'tcp' # - nic_mapping: # Mapping of network configuration for Overcloud Nodes - compute: # Mapping for compute profile (nodes that will be used as Compute nodes) - phys_type: interface # Physical interface type (interface or bond) - vlan: 101 # VLAN tag to use with this NIC - members: # Physical NIC members of this mapping (Single value allowed for interface phys_type) - - eth1 # Note, for Apex you may also use the logical nic name (found by nic order), such as "nic1" - controller: # Mapping for controller profile (nodes that will be used as Controller nodes) - phys_type: interface - vlan: 101 - members: - - eth1 - external_overlay: # External network to be created in OpenStack by Services tenant - name: private_cloud - type: vlan - segmentation_id: 101 - gateway: 192.168.38.1 - - storage: # Storage network configuration - enabled: true - cidr: 12.0.0.0/24 # Subnet in CIDR format - vlan: 12 # VLAN tag to use for Overcloud hosts on this network - mtu: 64000 # Tenant network MTU - nic_mapping: # Mapping of network configuration for Overcloud Nodes - compute: # Mapping for compute profile (nodes that will be used as Compute nodes) - phys_type: bond # Physical interface type (interface or bond) - vlan: 12 # VLAN tag to use with this NIC - members: # Physical NIC members of this mapping (Single value allowed for interface phys_type) - - eth3 # Note, for Apex you may also use the logical nic name (found by nic order), such as "nic1" - - eth4 - controller: # Mapping for controller profile (nodes that will be used as Controller nodes) - phys_type: bond - vlan: 12 - members: - - eth3 - - eth4 - - api: # API network configuration - enabled: false - cidr: fd00:fd00:fd00:4000::/64 # Subnet in CIDR format - vlan: 13 # VLAN tag to use for Overcloud hosts on this network - mtu: 64000 # Tenant network MTU - nic_mapping: # Mapping of network configuration for Overcloud Nodes - compute: # Mapping for compute profile (nodes that will be used as Compute nodes) - phys_type: bond # Physical interface type (interface or bond) - vlan: 13 # VLAN tag to use with this NIC - members: # Physical NIC members of this mapping (Single value allowed for interface phys_type) - - eth3 # Note, for Apex you may also use the logical nic name (found by nic order), such as "nic1" - - eth4 - controller: # Mapping for controller profile (nodes that will be used as Controller nodes) - phys_type: bond - vlan: 13 - members: - - eth3 - - eth4 - -# JOID specific settings -joid: - -# Compass specific settings -compass: - -# Apex specific settings -apex: - networks: - admin: - introspection_range: 192.0.2.100,192.0.2.120 # Range used for introspection phase (examining nodes) -# Fuel specific settings -fuel: |