summaryrefslogtreecommitdiffstats
path: root/docs/development/design/ndrpdr.rst
diff options
context:
space:
mode:
authorahothan <ahothan@cisco.com>2018-04-25 10:51:40 -0700
committerahothan <ahothan@cisco.com>2018-04-25 10:51:40 -0700
commite48023137b7010e9e1640649ea2859009a362939 (patch)
treeb4ade286684c7356977bb2e62cb39b954abe3472 /docs/development/design/ndrpdr.rst
parenteff9ff971acf5c7208ab2b824b897d3183c36f3c (diff)
Update doc1.4.1
Change-Id: I71bcf634033c78866d6808a4604b33629710ec23 Signed-off-by: ahothan <ahothan@cisco.com>
Diffstat (limited to 'docs/development/design/ndrpdr.rst')
-rw-r--r--docs/development/design/ndrpdr.rst51
1 files changed, 45 insertions, 6 deletions
diff --git a/docs/development/design/ndrpdr.rst b/docs/development/design/ndrpdr.rst
index 5361174..e34e8ba 100644
--- a/docs/development/design/ndrpdr.rst
+++ b/docs/development/design/ndrpdr.rst
@@ -6,11 +6,15 @@
NDR/PDR Binary Search
=====================
+The NDR/PDR binary search algorithm used by NFVbench is based on the algorithm used by the
+FD.io CSIT project, with some additional optimizations.
+
Algorithm Outline
-----------------
-The ServiceChain class is responsible for calculating the NDR/PDR for all frame sizes requested in the configuration.
-Calculation for 1 frame size is delegated to the TrafficClient class.
+The ServiceChain class (nfvbench/service_chain.py) is responsible for calculating the NDR/PDR
+or all frame sizes requested in the configuration.
+Calculation for 1 frame size is delegated to the TrafficClient class (nfvbench/traffic_client.py)
Call chain for calculating the NDR-PDR for a list of frame sizes:
@@ -22,23 +26,58 @@ Call chain for calculating the NDR-PDR for a list of frame sizes:
- TrafficClient.__range_search() recursive binary search
The search range is delimited by a left and right rate (expressed as a % of line rate per direction).
+The search always start at line rate per port, e.g. in the case of 2x10Gbps, the first iteration
+will send 10Gbps of traffic on each port.
The load_epsilon configuration parameter defines the accuracy of the result as a % of line rate.
The default value of 0.1 indicates for example that the measured NDR and PDR are within 0.1% of line rate of the
actual NDR/PDR (e.g. 0.1% of 10Gbps is 10Mbps). It also determines how small the search range must be in the binary search.
+Smaller values of load_epsilon will result in more iterations and will take more time but may not
+always be beneficial if the absolute value falls below the precision level of the measurement.
+For example a value of 0.01% would translate to an absolute value of 1Mbps (for a 10Gbps port) or
+around 10kpps (at 64 byte size) which might be too fine grain.
The recursion narrows down the range by half and stops when:
- the range is smaller than the configured load_epsilon value
- or when the search hits 100% or 0% of line rate
+Optimization
+------------
+
+Binary search algorithms assume that the drop rate curve is monotonically increasing with the Tx rate.
+To save time, the algorithm used by NFVbench is capable of calculating the optimal Tx rate for an
+arbitrary list of target maximum drop rates in one pass instead of the usual 1 pass per target maximum drop rate.
+This saves time linearly to the number target drop rates.
+For example, a typical NDR/PDR search will have 2 target maximum drop rates:
+
+- NDR = 0.001%
+- PDR = 0.1%
+
+The binary search will then start with a sorted list of 2 target drop rates: [0.1, 0.001].
+The first part of the binary search will then focus on finding the optimal rate for the first target
+drop rate (0.1%). When found, the current target drop rate is removed from the list and
+iteration continues with the next target drop rate in the list but this time
+starting from the upper/lower range of the previous target drop rate, which saves significant time.
+The binary search continues until the target maximum drop rate list is empty.
+
+Results Granularity
+-------------------
+The binary search results contain per direction stats (forward and reverse).
+In the case of multi-chaining, results contain per chain stats.
+The current code only reports aggregated stats (forward + reverse for all chains) but could be enhanced
+to report per chain stats.
+
+
+CPU Limitations
+---------------
One particularity of using a software traffic generator is that the requested Tx rate may not always be met due to
resource limitations (e.g. CPU is not fast enough to generate a very high load). The algorithm should take this into
consideration:
-- always monitor the actual Tx rate achieved
+- always monitor the actual Tx rate achieved as reported back by the traffic generator
- actual Tx rate is always <= requested Tx rate
- the measured drop rate should always be relative to the actual Tx rate
-- if the actual Tx rate is < requested Tx rate and the measured drop rate is already within threshold (<NDR/PDR threshold) then the binary search must stop with proper warning
-
-
+- if the actual Tx rate is < requested Tx rate and the measured drop rate is already within threshold
+ (<NDR/PDR threshold) then the binary search must stop with proper warning because the actual NDR/PDR
+ might probably be higher than the reported values