1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
|
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/pci.h>
#include <linux/io.h>
#include <linux/sh_intc.h>
#include "pci-sh4.h"
int __init pcibios_map_platform_irq(const struct pci_dev *, u8 slot, u8 pin)
{
switch (slot) {
case 0: return evt2irq(0x3a0);
case 1: return evt2irq(0x3a0); /* AMD Ethernet controller */
case 2: return -1;
case 3: return -1;
case 4: return -1;
default:
printk("PCI: Bad IRQ mapping request for slot %d\n", slot);
return -1;
}
}
#define PCIMCR_MRSET_OFF 0xBFFFFFFF
#define PCIMCR_RFSH_OFF 0xFFFFFFFB
/*
* Only long word accesses of the PCIC's internal local registers and the
* configuration registers from the CPU is supported.
*/
#define PCIC_WRITE(x,v) writel((v), PCI_REG(x))
#define PCIC_READ(x) readl(PCI_REG(x))
/*
* Description: This function sets up and initializes the pcic, sets
* up the BARS, maps the DRAM into the address space etc, etc.
*/
int pci_fixup_pcic(struct pci_channel *chan)
{
unsigned long bcr1, wcr1, wcr2, wcr3, mcr;
unsigned short bcr2;
/*
* Initialize the slave bus controller on the pcic. The values used
* here should not be hardcoded, but they should be taken from the bsc
* on the processor, to make this function as generic as possible.
* (i.e. Another sbc may usr different SDRAM timing settings -- in order
* for the pcic to work, its settings need to be exactly the same.)
*/
bcr1 = (*(volatile unsigned long*)(SH7751_BCR1));
bcr2 = (*(volatile unsigned short*)(SH7751_BCR2));
wcr1 = (*(volatile unsigned long*)(SH7751_WCR1));
wcr2 = (*(volatile unsigned long*)(SH7751_WCR2));
wcr3 = (*(volatile unsigned long*)(SH7751_WCR3));
mcr = (*(volatile unsigned long*)(SH7751_MCR));
bcr1 = bcr1 | 0x00080000; /* Enable Bit 19, BREQEN */
(*(volatile unsigned long*)(SH7751_BCR1)) = bcr1;
bcr1 = bcr1 | 0x40080000; /* Enable Bit 19 BREQEN, set PCIC to slave */
PCIC_WRITE(SH7751_PCIBCR1, bcr1); /* PCIC BCR1 */
PCIC_WRITE(SH7751_PCIBCR2, bcr2); /* PCIC BCR2 */
PCIC_WRITE(SH7751_PCIWCR1, wcr1); /* PCIC WCR1 */
PCIC_WRITE(SH7751_PCIWCR2, wcr2); /* PCIC WCR2 */
PCIC_WRITE(SH7751_PCIWCR3, wcr3); /* PCIC WCR3 */
mcr = (mcr & PCIMCR_MRSET_OFF) & PCIMCR_RFSH_OFF;
PCIC_WRITE(SH7751_PCIMCR, mcr); /* PCIC MCR */
/* Enable all interrupts, so we know what to fix */
PCIC_WRITE(SH7751_PCIINTM, 0x0000c3ff);
PCIC_WRITE(SH7751_PCIAINTM, 0x0000380f);
/* Set up standard PCI config registers */
PCIC_WRITE(SH7751_PCICONF1, 0xF39000C7); /* Bus Master, Mem & I/O access */
PCIC_WRITE(SH7751_PCICONF2, 0x00000000); /* PCI Class code & Revision ID */
PCIC_WRITE(SH7751_PCICONF4, 0xab000001); /* PCI I/O address (local regs) */
PCIC_WRITE(SH7751_PCICONF5, 0x0c000000); /* PCI MEM address (local RAM) */
PCIC_WRITE(SH7751_PCICONF6, 0xd0000000); /* PCI MEM address (unused) */
PCIC_WRITE(SH7751_PCICONF11, 0x35051054); /* PCI Subsystem ID & Vendor ID */
PCIC_WRITE(SH7751_PCILSR0, 0x03f00000); /* MEM (full 64M exposed) */
PCIC_WRITE(SH7751_PCILSR1, 0x00000000); /* MEM (unused) */
PCIC_WRITE(SH7751_PCILAR0, 0x0c000000); /* MEM (direct map from PCI) */
PCIC_WRITE(SH7751_PCILAR1, 0x00000000); /* MEM (unused) */
/* Now turn it on... */
PCIC_WRITE(SH7751_PCICR, 0xa5000001);
/*
* Set PCIMBR and PCIIOBR here, assuming a single window
* (16M MEM, 256K IO) is enough. If a larger space is
* needed, the readx/writex and inx/outx functions will
* have to do more (e.g. setting registers for each call).
*/
/*
* Set the MBR so PCI address is one-to-one with window,
* meaning all calls go straight through... use BUG_ON to
* catch erroneous assumption.
*/
BUG_ON(chan->resources[1].start != SH7751_PCI_MEMORY_BASE);
PCIC_WRITE(SH7751_PCIMBR, chan->resources[1].start);
/* Set IOBR for window containing area specified in pci.h */
PCIC_WRITE(SH7751_PCIIOBR, (chan->resources[0].start & SH7751_PCIIOBR_MASK));
/* All done, may as well say so... */
printk("SH7751 PCI: Finished initialization of the PCI controller\n");
return 1;
}
|
