diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/xpedite537x.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/xpedite537x.h | 601 |
1 files changed, 0 insertions, 601 deletions
diff --git a/qemu/roms/u-boot/include/configs/xpedite537x.h b/qemu/roms/u-boot/include/configs/xpedite537x.h deleted file mode 100644 index bdf55763d..000000000 --- a/qemu/roms/u-boot/include/configs/xpedite537x.h +++ /dev/null @@ -1,601 +0,0 @@ -/* - * Copyright 2008 Extreme Engineering Solutions, Inc. - * Copyright 2007-2008 Freescale Semiconductor, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * xpedite537x board configuration file - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_BOOKE 1 /* BOOKE */ -#define CONFIG_E500 1 /* BOOKE e500 family */ -#define CONFIG_MPC8572 1 -#define CONFIG_XPEDITE5370 1 -#define CONFIG_SYS_BOARD_NAME "XPedite5370" -#define CONFIG_SYS_FORM_3U_VPX 1 -#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xfff80000 -#endif - -#define CONFIG_PCI 1 /* Enable PCI/PCIE */ -#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ -#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ -#define CONFIG_PCIE1 1 /* PCIE controler 1 */ -#define CONFIG_PCIE2 1 /* PCIE controler 2 */ -#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ -#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ -#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ -#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ -#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ -#define CONFIG_FSL_ELBC 1 - -/* - * Multicore config - */ -#define CONFIG_MP -#define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */ -#define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */ - -/* - * DDR config - */ -#define CONFIG_SYS_FSL_DDR2 -#undef CONFIG_FSL_DDR_INTERACTIVE -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -#define CONFIG_DDR_SPD -#define CONFIG_MEM_INIT_VALUE 0xdeadbeef -#define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ -#define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ -#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ -#define CONFIG_NUM_DDR_CONTROLLERS 2 -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL 1 -#define CONFIG_DDR_ECC -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE -#define CONFIG_VERY_BIG_RAM - -#ifndef __ASSEMBLY__ -extern unsigned long get_board_sys_clk(unsigned long dummy); -extern unsigned long get_board_ddr_clk(unsigned long dummy); -#endif - -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ -#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_ENABLE_36BIT_PHYS 1 - -#define CONFIG_SYS_CCSRBAR 0xef000000 -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR - -/* - * Diagnostics - */ -#define CONFIG_SYS_ALT_MEMTEST -#define CONFIG_SYS_MEMTEST_START 0x10000000 -#define CONFIG_SYS_MEMTEST_END 0x20000000 -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_I2C) -#define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \ - CONFIG_SYS_I2C_DS4510_ADDR, \ - CONFIG_SYS_I2C_EEPROM_ADDR, \ - CONFIG_SYS_I2C_LM90_ADDR, \ - CONFIG_SYS_I2C_PCA953X_ADDR0, \ - CONFIG_SYS_I2C_PCA953X_ADDR1, \ - CONFIG_SYS_I2C_PCA953X_ADDR2, \ - CONFIG_SYS_I2C_PCA953X_ADDR3, \ - CONFIG_SYS_I2C_PEX8518_ADDR, \ - CONFIG_SYS_I2C_RTC_ADDR} -/* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */ -#define I2C_ADDR_IGNORE_LIST {0x50} - -/* - * Memory map - * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable - * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable - * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable - * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable - * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable - * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable - * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable - * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable - * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable - * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable - * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable - */ - -#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) - -/* - * NAND flash configuration - */ -#define CONFIG_SYS_NAND_BASE 0xef800000 -#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ -#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \ - CONFIG_SYS_NAND_BASE2} -#define CONFIG_SYS_MAX_NAND_DEVICE 2 -#define CONFIG_MTD_NAND_VERIFY_WRITE -#define CONFIG_SYS_NAND_QUIET_TEST /* 2nd NAND flash not always populated */ -#define CONFIG_NAND_FSL_ELBC - -/* - * NOR flash configuration - */ -#define CONFIG_SYS_FLASH_BASE 0xf8000000 -#define CONFIG_SYS_FLASH_BASE2 0xf0000000 -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE -#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ - {0xf7f40000, 0xc0000} } -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -/* - * Chip select configuration - */ -/* NOR Flash 0 on CS0 */ -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ - BR_PS_16 | \ - BR_V) -#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ - OR_GPCM_CSNT | \ - OR_GPCM_XACS | \ - OR_GPCM_ACS_DIV2 | \ - OR_GPCM_SCY_8 | \ - OR_GPCM_TRLX | \ - OR_GPCM_EHTR | \ - OR_GPCM_EAD) - -/* NOR Flash 1 on CS1 */ -#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ - BR_PS_16 | \ - BR_V) -#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM - -/* NAND flash on CS2 */ -#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ - (2<<BR_DECC_SHIFT) | \ - BR_PS_8 | \ - BR_MS_FCM | \ - BR_V) - -/* NAND flash on CS2 */ -#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ - OR_FCM_PGS | \ - OR_FCM_CSCT | \ - OR_FCM_CST | \ - OR_FCM_CHT | \ - OR_FCM_SCY_1 | \ - OR_FCM_TRLX | \ - OR_FCM_EHTR) - -/* NAND flash on CS3 */ -#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ - (2<<BR_DECC_SHIFT) | \ - BR_PS_8 | \ - BR_MS_FCM | \ - BR_V) -#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM - -/* - * Use L1 as initial stack - */ -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} -#define CONFIG_BAUDRATE 115200 -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * Use the HUSH parser - */ -#define CONFIG_SYS_HUSH_PARSER - -/* - * Pass open firmware flat tree - */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS 1 - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } - -/* PEX8518 slave I2C interface */ -#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 - -/* I2C DS1631 temperature sensor */ -#define CONFIG_SYS_I2C_DS1621_ADDR 0x48 -#define CONFIG_DTT_DS1621 -#define CONFIG_DTT_SENSORS { 0 } -#define CONFIG_SYS_I2C_LM90_ADDR 0x4c - -/* I2C EEPROM - AT24C128B */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ - -/* I2C RTC */ -#define CONFIG_RTC_M41T11 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#define CONFIG_SYS_M41T11_BASE_YEAR 2000 - -/* GPIO/EEPROM/SRAM */ -#define CONFIG_DS4510 -#define CONFIG_SYS_I2C_DS4510_ADDR 0x51 - -/* GPIO */ -#define CONFIG_PCA953X -#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 -#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c -#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e -#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f -#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 - -/* - * PU = pulled high, PD = pulled low - * I = input, O = output, IO = input/output - */ -/* PCA9557 @ 0x18*/ -#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ -#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ -#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ -#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ -#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ -#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ -#define CONFIG_SYS_PCA953X_C0_VCORE_VID2 0x40 /* VID2 of ISL6262 */ -#define CONFIG_SYS_PCA953X_C0_VCORE_VID3 0x80 /* VID3 of ISL6262 */ - -/* PCA9557 @ 0x1c*/ -#define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ -#define CONFIG_SYS_PCA953X_XMC0_MVMR0 0x02 /* XMC EEPROM write protect */ -#define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ -#define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ -#define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ -#define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ -#define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ -#define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ - -/* PCA9557 @ 0x1e*/ -#define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ -#define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ -#define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ -#define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ -#define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ -#define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; tied to VPX P0.GAP */ -#define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */ - -/* PCA9557 @ 0x1f */ -#define CONFIG_SYS_PCA953X_GPIO_VPX0 0x01 /* PU */ -#define CONFIG_SYS_PCA953X_GPIO_VPX1 0x02 /* PU */ -#define CONFIG_SYS_PCA953X_GPIO_VPX2 0x04 /* PU */ -#define CONFIG_SYS_PCA953X_GPIO_VPX3 0x08 /* PU */ -#define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL 0x10 /* PD; I2C master source for FRU SEEPROM */ - -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ -/* PCIE1 - VPX P1 */ -#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ - -/* PCIE2 - PEX8518 */ -#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ - -/* - * Networking options - */ -#define CONFIG_TSEC_ENET /* tsec ethernet support */ -#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CONFIG_TSEC_TBI -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ -#define CONFIG_ETHPRIME "eTSEC2" - -/* - * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force - * 1000mbps SGMII link - */ -#define CONFIG_TSEC_TBICR_SETTINGS ( \ - TBICR_PHY_RESET \ - | TBICR_FULL_DUPLEX \ - | TBICR_SPEED1_SET \ - ) - -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "eTSEC1" -#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC1_PHY_ADDR 1 -#define TSEC1_PHYIDX 0 -#define CONFIG_HAS_ETH0 - -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "eTSEC2" -#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC2_PHY_ADDR 2 -#define TSEC2_PHYIDX 0 -#define CONFIG_HAS_ETH1 - -/* - * Command configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DS4510 -#define CONFIG_CMD_DS4510_INFO -#define CONFIG_CMD_DTT -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FLASH -#define CONFIG_CMD_I2C -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_PCA953X -#define CONFIG_CMD_PCA953X_INFO -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PCI_ENUM -#define CONFIG_CMD_PING -#define CONFIG_CMD_SAVEENV -#define CONFIG_CMD_SNTP -#define CONFIG_CMD_REGINFO - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ -#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ -#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ -#define CONFIG_PANIC_HANG /* do not reset board on panic */ -#define CONFIG_PREBOOT /* enable preboot variable */ -#define CONFIG_FIT 1 -#define CONFIG_FIT_VERBOSE 1 -#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 16 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ - -/* - * Environment Configuration - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ -#define CONFIG_ENV_SIZE 0x8000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) - -/* - * Flash memory map: - * fff80000 - ffffffff Pri U-Boot (512 KB) - * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) - * fff00000 - fff3ffff Pri FDT (256KB) - * fef00000 - ffefffff Pri OS image (16MB) - * f8000000 - feefffff Pri OS Use/Filesystem (111MB) - * - * f7f80000 - f7ffffff Sec U-Boot (512 KB) - * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) - * f7f00000 - f7f3ffff Sec FDT (256KB) - * f6f00000 - f7efffff Sec OS image (16MB) - * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) - */ -#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000) -#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000) -#define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000) -#define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000) -#define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) -#define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000) - -#define CONFIG_PROG_UBOOT1 \ - "$download_cmd $loadaddr $ubootfile; " \ - "if test $? -eq 0; then " \ - "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ - "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ - "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ - "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ - "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ - "if test $? -ne 0; then " \ - "echo PROGRAM FAILED; " \ - "else; " \ - "echo PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_UBOOT2 \ - "$download_cmd $loadaddr $ubootfile; " \ - "if test $? -eq 0; then " \ - "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ - "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ - "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ - "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ - "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ - "if test $? -ne 0; then " \ - "echo PROGRAM FAILED; " \ - "else; " \ - "echo PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_BOOT_OS_NET \ - "$download_cmd $osaddr $osfile; " \ - "if test $? -eq 0; then " \ - "if test -n $fdtaddr; then " \ - "$download_cmd $fdtaddr $fdtfile; " \ - "if test $? -eq 0; then " \ - "bootm $osaddr - $fdtaddr; " \ - "else; " \ - "echo FDT DOWNLOAD FAILED; " \ - "fi; " \ - "else; " \ - "bootm $osaddr; " \ - "fi; " \ - "else; " \ - "echo OS DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_OS1 \ - "$download_cmd $osaddr $osfile; " \ - "if test $? -eq 0; then " \ - "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ - "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ - "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ - "if test $? -ne 0; then " \ - "echo OS PROGRAM FAILED; " \ - "else; " \ - "echo OS PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo OS DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_OS2 \ - "$download_cmd $osaddr $osfile; " \ - "if test $? -eq 0; then " \ - "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ - "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ - "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ - "if test $? -ne 0; then " \ - "echo OS PROGRAM FAILED; " \ - "else; " \ - "echo OS PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo OS DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_FDT1 \ - "$download_cmd $fdtaddr $fdtfile; " \ - "if test $? -eq 0; then " \ - "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ - "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ - "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ - "if test $? -ne 0; then " \ - "echo FDT PROGRAM FAILED; " \ - "else; " \ - "echo FDT PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo FDT DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_FDT2 \ - "$download_cmd $fdtaddr $fdtfile; " \ - "if test $? -eq 0; then " \ - "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ - "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ - "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ - "if test $? -ne 0; then " \ - "echo FDT PROGRAM FAILED; " \ - "else; " \ - "echo FDT PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo FDT DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "autoload=yes\0" \ - "download_cmd=tftp\0" \ - "console_args=console=ttyS0,115200\0" \ - "root_args=root=/dev/nfs rw\0" \ - "misc_args=ip=on\0" \ - "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ - "bootfile=/home/user/file\0" \ - "osfile=/home/user/board.uImage\0" \ - "fdtfile=/home/user/board.dtb\0" \ - "ubootfile=/home/user/u-boot.bin\0" \ - "fdtaddr=c00000\0" \ - "osaddr=0x1000000\0" \ - "loadaddr=0x1000000\0" \ - "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ - "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ - "prog_os1="CONFIG_PROG_OS1"\0" \ - "prog_os2="CONFIG_PROG_OS2"\0" \ - "prog_fdt1="CONFIG_PROG_FDT1"\0" \ - "prog_fdt2="CONFIG_PROG_FDT2"\0" \ - "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ - "bootcmd_flash1=run set_bootargs; " \ - "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ - "bootcmd_flash2=run set_bootargs; " \ - "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ - "bootcmd=run bootcmd_flash1\0" -#endif /* __CONFIG_H */ |