diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/xpedite1000.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/xpedite1000.h | 337 |
1 files changed, 0 insertions, 337 deletions
diff --git a/qemu/roms/u-boot/include/configs/xpedite1000.h b/qemu/roms/u-boot/include/configs/xpedite1000.h deleted file mode 100644 index ca322b2e8..000000000 --- a/qemu/roms/u-boot/include/configs/xpedite1000.h +++ /dev/null @@ -1,337 +0,0 @@ -/* - * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * config for XPedite1000 from XES Inc. - * Ported from EBONY config by Travis B. Sawyer <tsawyer@sandburst.com> - * (C) Copyright 2003 Sandburst Corporation - * board/config_EBONY.h - configuration for AMCC 440GP Ref (Ebony) - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* High Level Configuration Options */ -#define CONFIG_XPEDITE1000 1 -#define CONFIG_SYS_BOARD_NAME "XPedite1000" -#define CONFIG_SYS_FORM_PMC 1 -#define CONFIG_440 1 -#define CONFIG_440GX 1 /* 440 GX */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ - -#define CONFIG_SYS_TEXT_BASE 0xFFF80000 - -/* - * DDR config - */ -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ -#define SPD_EEPROM_ADDRESS {0x54} /* SPD i2c spd addresses */ -#define CONFIG_VERY_BIG_RAM 1 - -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ -#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ -#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000) -#define CONFIG_SYS_GPIO_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700) - -/* - * Diagnostics - */ -#define CONFIG_SYS_ALT_MEMTEST -#define CONFIG_SYS_MEMTEST_START 0x0400000 -#define CONFIG_SYS_MEMTEST_END 0x0C00000 - -/* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_RTC | \ - CONFIG_SYS_POST_I2C) - -/* - * LED support - */ -#define USR_LED0 0x00000080 -#define USR_LED1 0x00000100 -#define USR_LED2 0x00000200 -#define USR_LED3 0x00000400 - -#ifndef __ASSEMBLY__ -extern unsigned long in32(unsigned int); -extern void out32(unsigned int, unsigned long); - -#define LED0_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED0)) -#define LED1_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED1)) -#define LED2_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED2)) -#define LED3_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED3)) - -#define LED0_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED0)) -#define LED1_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED1)) -#define LED2_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED2)) -#define LED3_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED3)) -#endif - -/* - * Use internal SRAM for initial stack - */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 -#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) - -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400} -#define CONFIG_BAUDRATE 115200 -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * Use the HUSH parser - */ -#define CONFIG_SYS_HUSH_PARSER - -/* - * NOR flash configuration - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 3 -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, 0xf0000000, 0xf4000000 } -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE -#define CONFIG_SYS_FLASH_QUIET_TEST /* MirrorBit flashes are optional */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7f - -/* I2C EEPROM */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - -/* I2C RTC: STMicro M41T00 */ -#define CONFIG_RTC_M41T11 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#define CONFIG_SYS_M41T11_BASE_YEAR 2000 - -/* - * PCI - */ -/* General PCI */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */ - -/* Board-specific PCI */ -#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -#define CONFIG_SYS_PCI_FORCE_PCI_CONV /* Force PCI Conventional Mode */ - -/* - * Networking options - */ -#define CONFIG_PPC4xx_EMAC -#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ -#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ -#define CONFIG_ETHPRIME "ppc_4xx_eth2" -#define CONFIG_PHY_ADDR 4 /* PHY address phy0 not populated */ -#define CONFIG_PHY2_ADDR 4 /* PHY address phy2 */ -#define CONFIG_HAS_ETH2 1 /* add support for "eth2addr" */ -#define CONFIG_PHY3_ADDR 8 /* PHY address phy3 */ -#define CONFIG_HAS_ETH3 1 /* add support for "eth3addr" */ - -/* BOOTP options */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command configuration - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FLASH -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_SAVEENV -#define CONFIG_CMD_SNTP - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_CMDLINE_EDITING 1 /* Command-line editing */ -#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ -#define CONFIG_PANIC_HANG /* do not reset board on panic */ -#define CONFIG_PREBOOT /* enable preboot variable */ -#define CONFIG_FIT 1 -#define CONFIG_FIT_VERBOSE 1 -#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Environment Configuration - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ -#define CONFIG_ENV_SIZE 0x8000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) - -/* - * Flash memory map: - * fff80000 - ffffffff U-Boot (512 KB) - * fff40000 - fff7ffff U-Boot Environment (256 KB) - * fff00000 - fff3ffff FDT (256KB) - * ffc00000 - ffefffff OS image (3MB) - * ff000000 - ffbfffff OS Use/Filesystem (12MB) - */ - -#define CONFIG_UBOOT_ENV_ADDR __stringify(CONFIG_SYS_TEXT_BASE) -#define CONFIG_FDT_ENV_ADDR __stringify(0xfff00000) -#define CONFIG_OS_ENV_ADDR __stringify(0xffc00000) - -#define CONFIG_PROG_UBOOT \ - "$download_cmd $loadaddr $ubootfile; " \ - "if test $? -eq 0; then " \ - "protect off "CONFIG_UBOOT_ENV_ADDR" +80000; " \ - "erase "CONFIG_UBOOT_ENV_ADDR" +80000; " \ - "cp.w $loadaddr "CONFIG_UBOOT_ENV_ADDR" 40000; " \ - "protect on "CONFIG_UBOOT_ENV_ADDR" +80000; " \ - "cmp.b $loadaddr "CONFIG_UBOOT_ENV_ADDR" 80000; " \ - "if test $? -ne 0; then " \ - "echo PROGRAM FAILED; " \ - "else; " \ - "echo PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_BOOT_OS_NET \ - "$download_cmd $osaddr $osfile; " \ - "if test $? -eq 0; then " \ - "if test -n $fdtaddr; then " \ - "$download_cmd $fdtaddr $fdtfile; " \ - "if test $? -eq 0; then " \ - "bootm $osaddr - $fdtaddr; " \ - "else; " \ - "echo FDT DOWNLOAD FAILED; " \ - "fi; " \ - "else; " \ - "bootm $osaddr; " \ - "fi; " \ - "else; " \ - "echo OS DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_OS \ - "$download_cmd $osaddr $osfile; " \ - "if test $? -eq 0; then " \ - "erase "CONFIG_OS_ENV_ADDR" +$filesize; " \ - "cp.b $osaddr "CONFIG_OS_ENV_ADDR" $filesize; " \ - "cmp.b $osaddr "CONFIG_OS_ENV_ADDR" $filesize; " \ - "if test $? -ne 0; then " \ - "echo OS PROGRAM FAILED; " \ - "else; " \ - "echo OS PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo OS DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_PROG_FDT \ - "$download_cmd $fdtaddr $fdtfile; " \ - "if test $? -eq 0; then " \ - "erase "CONFIG_FDT_ENV_ADDR" +$filesize;" \ - "cp.b $fdtaddr "CONFIG_FDT_ENV_ADDR" $filesize; " \ - "cmp.b $fdtaddr "CONFIG_FDT_ENV_ADDR" $filesize; " \ - "if test $? -ne 0; then " \ - "echo FDT PROGRAM FAILED; " \ - "else; " \ - "echo FDT PROGRAM SUCCEEDED; " \ - "fi; " \ - "else; " \ - "echo FDT DOWNLOAD FAILED; " \ - "fi;" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "autoload=yes\0" \ - "download_cmd=tftp\0" \ - "console_args=console=ttyS0,115200\0" \ - "root_args=root=/dev/nfs rw\0" \ - "misc_args=ip=on\0" \ - "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ - "bootfile=/home/user/file\0" \ - "osfile=/home/user/board.uImage\0" \ - "fdtfile=/home/user/board.dtb\0" \ - "ubootfile=/home/user/u-boot.bin\0" \ - "fdtaddr=c00000\0" \ - "osaddr=0x1000000\0" \ - "loadaddr=0x1000000\0" \ - "prog_uboot="CONFIG_PROG_UBOOT"\0" \ - "prog_os="CONFIG_PROG_OS"\0" \ - "prog_fdt="CONFIG_PROG_FDT"\0" \ - "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ - "bootcmd_flash=run set_bootargs; " \ - "bootm "CONFIG_OS_ENV_ADDR" - "CONFIG_FDT_ENV_ADDR"\0" \ - "bootcmd=run bootcmd_flash\0" -#endif /* __CONFIG_H */ |