diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/p3p440.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/p3p440.h | 306 |
1 files changed, 0 insertions, 306 deletions
diff --git a/qemu/roms/u-boot/include/configs/p3p440.h b/qemu/roms/u-boot/include/configs/p3p440.h deleted file mode 100644 index 225567bd9..000000000 --- a/qemu/roms/u-boot/include/configs/p3p440.h +++ /dev/null @@ -1,306 +0,0 @@ -/* - * (C) Copyright 2005-2006 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/************************************************************************ - * board/config_p3p440.h - configuration for Prodrive P3P440 - ***********************************************************************/ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/*----------------------------------------------------------------------- - * High Level Configuration Options - *----------------------------------------------------------------------*/ -#define CONFIG_P3P440 1 /* Board is P3P440 */ -#define CONFIG_440GP 1 /* Specifc GP support */ -#define CONFIG_440 1 /* ... PPC440 family */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ - -#define CONFIG_SYS_TEXT_BASE 0xFFFC0000 - -#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ - -/*----------------------------------------------------------------------- - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH */ -#define CONFIG_SYS_MONITOR_BASE 0xfffc0000 /* start of monitor */ -#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ -#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ - -#define CONFIG_SYS_USB_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000000) - -/*----------------------------------------------------------------------- - * Initial RAM & stack pointer (placed in internal SRAM) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ - -/*----------------------------------------------------------------------- - * DDR SDRAM - *----------------------------------------------------------------------*/ -#define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0*/ -#define CONFIG_SDRAM_ECC /* enable ECC support */ -#define CONFIG_SYS_SDRAM_TABLE { \ - {(256 << 20), 13, 0x000C4001}, /* 256MB mode 3, 13x10(4)*/ \ - {(64 << 20), 12, 0x00082001}} /* 64MB mode 2, 12x9(4) */ - -/*----------------------------------------------------------------------- - * Serial Port - *----------------------------------------------------------------------*/ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - -#undef CONFIG_SYS_EXT_SERIAL_CLOCK -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ - 57600, 115200, 230400, 460800, 921600 } - -/*----------------------------------------------------------------------- - * I2C - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */ - -/*----------------------------------------------------------------------- - * I2C RTC - *----------------------------------------------------------------------*/ -#define CONFIG_RTC_MAX6900 1 /* MAX6900 RTC */ - -/*----------------------------------------------------------------------- - * I2C EEPROM (PCF8594C) for environment - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 /* EEPROM PCF8594C */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* The Philips PCF8594C has */ - /* 8 byte page write mode using */ - /* last 3 bits of the address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 40 /* and takes up to 40 msec */ - -/*----------------------------------------------------------------------- - * Default configuration (environment varibles...) - *----------------------------------------------------------------------*/ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=p3p440\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/p3p440/uImage\0" \ - "kernel_addr=ff800000\0" \ - "ramdisk_addr=ff810000\0" \ - "load=tftp 100000 /tftpboot/p3p440/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "unlock=yes\0" \ - "" -#define CONFIG_BOOTCOMMAND "run net_nfs" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0x1c /* PHY address */ -#define CONFIG_HAS_ETH1 -#define CONFIG_PHY1_ADDR 0x1d /* EMAC1 PHY address */ -#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_SNTP - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------*/ -/* General PCI */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */ - -/* Board-specific PCI */ -#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ - -#define CONFIG_DISABLE_PISE_TEST /* disable PISE test (PCIX only)*/ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ - -/*----------------------------------------------------------------------- - * External Bus Controller (EBC) Setup - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH0 0xFF800000 -#define CONFIG_SYS_FLASH1 0xFF000000 -#define CONFIG_SYS_FLASH2 0xFE800000 -#define CONFIG_SYS_FLASH3 0xFE000000 -#define CONFIG_SYS_USB 0xF0000000 - -/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x03050200 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH0 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */ - -/* Memory Bank 1 (Flash Bank 1, NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB1AP 0x03050200 -#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_FLASH1 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */ - -/* Memory Bank 2 (Flash Bank 2, NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x03050200 -#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FLASH2 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */ - -/* Memory Bank 3 (Flash Bank 3, NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB3AP 0x03050200 -#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_FLASH3 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */ - -/* Memory Bank 7 (USB controller) initialization */ -#define CONFIG_SYS_EBC_PB7AP 0x02015000 -#define CONFIG_SYS_EBC_PB7CR (CONFIG_SYS_USB | 0xFE000) /* BAS=0xF00,BS=128MB,BU=R/W,BW=16bit*/ - -/*----------------------------------------------------------------------- - * FLASH related - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ - -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH3, CONFIG_SYS_FLASH2, CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } - -#define CONFIG_SYS_MAX_FLASH_BANKS 4 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ - -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ - -#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif -#endif /* __CONFIG_H */ |