diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/otc570.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/otc570.h | 258 |
1 files changed, 0 insertions, 258 deletions
diff --git a/qemu/roms/u-boot/include/configs/otc570.h b/qemu/roms/u-boot/include/configs/otc570.h deleted file mode 100644 index 629967d05..000000000 --- a/qemu/roms/u-boot/include/configs/otc570.h +++ /dev/null @@ -1,258 +0,0 @@ -/* - * (C) Copyright 2010-2011 - * Daniel Gorsulowski <daniel.gorsulowski@esd.eu> - * esd electronic system design gmbh <www.esd.eu> - * - * (C) Copyright 2007-2008 - * Stelian Pop <stelian@popies.net> - * Lead Tech Design <www.leadtechdesign.com> - * - * Configuation settings for the esd OTC570 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * SoC must be defined first, before hardware.h is included. - * In this case SoC is defined in boards.cfg. - */ -#include <asm/hardware.h> - -/* - * Warning: changing CONFIG_SYS_TEXT_BASE requires - * adapting the initial boot program. - * Since the linker has to swallow that define, we must use a pure - * hex number here! - */ -#define CONFIG_SYS_TEXT_BASE 0x20002000 - -/* - * since a number of boards are not being listed in linux - * arch/arm/tools/mach-types any more, the mach-types have to be - * defined here - */ -#define MACH_TYPE_OTC570 2166 - -/* ARM asynchronous clock */ -#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* 32.768 kHz crystal */ -#define CONFIG_SYS_AT91_MAIN_CLOCK 16000000/* 16.0 MHz crystal */ - -/* Misc CPU related */ -#define CONFIG_SKIP_LOWLEVEL_INIT -#define CONFIG_ARCH_CPU_INIT -#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f() */ -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG -#define CONFIG_SERIAL_TAG -#define CONFIG_REVISION_TAG -#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_MISC_INIT_R /* Call misc_init_r */ - -#define CONFIG_DISPLAY_BOARDINFO /* call checkboard() */ -#define CONFIG_DISPLAY_CPUINFO /* display cpu info and speed */ -#define CONFIG_PREBOOT /* enable preboot variable */ - -/* - * Hardware drivers - */ - -/* required until arch/arm/include/asm/arch-at91/at91sam9263.h is reworked */ -#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP - -/* general purpose I/O */ -#define CONFIG_AT91_GPIO - -/* Console output */ -#define CONFIG_ATMEL_USART -#define CONFIG_USART_BASE ATMEL_BASE_DBGU -#define CONFIG_USART_ID ATMEL_ID_SYS -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_BOOTDELAY 3 -#define CONFIG_ZERO_BOOTDELAY_CHECK - -/* LCD */ -#define CONFIG_LCD -#undef CONFIG_SPLASH_SCREEN - -#ifdef CONFIG_LCD -# define LCD_BPP LCD_COLOR8 - -# ifndef CONFIG_SPLASH_SCREEN -# define CONFIG_LCD_LOGO -# define CONFIG_LCD_INFO -# undef CONFIG_LCD_INFO_BELOW_LOGO -# endif /* CONFIG_SPLASH_SCREEN */ - -# undef LCD_TEST_PATTERN -# define CONFIG_SYS_WHITE_ON_BLACK -# define CONFIG_ATMEL_LCD -# define CONFIG_SYS_CONSOLE_IS_IN_ENV -# define CONFIG_OTC570_LCD_BASE (CONFIG_SYS_SDRAM_BASE + 0x03fa5000) -# define CONFIG_CMD_BMP -#endif /* CONFIG_LCD */ - -/* RTC and I2C stuff */ -#define CONFIG_RTC_DS1338 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ -#ifdef CONFIG_SYS_I2C_SOFT -#define CONFIG_SYS_I2C_SOFT_SPEED 100000 -#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F - -/* Configure data and clock pins for pio */ -# define I2C_INIT { \ - at91_set_pio_output(AT91_PIO_PORTB, 4, 0); \ - at91_set_pio_output(AT91_PIO_PORTB, 5, 0); \ -} -# define I2C_SOFT_DECLARATIONS -/* Configure data pin as output */ -# define I2C_ACTIVE at91_set_pio_output(AT91_PIO_PORTB, 4, 0) -/* Configure data pin as input */ -# define I2C_TRISTATE at91_set_pio_input(AT91_PIO_PORTB, 4, 0) -/* Read data pin */ -# define I2C_READ at91_get_pio_value(AT91_PIO_PORTB, 4) -/* Set data pin */ -# define I2C_SDA(bit) at91_set_pio_value(AT91_PIO_PORTB, 4, bit) -/* Set clock pin */ -# define I2C_SCL(bit) at91_set_pio_value(AT91_PIO_PORTB, 5, bit) -# define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SYS_I2C_SOFT */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> -#undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_LOADS -#undef CONFIG_CMD_IMLS - -#define CONFIG_CMD_PING -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_NAND -#define CONFIG_CMD_USB -#define CONFIG_CMD_I2C -#define CONFIG_CMD_DATE - -/* LED */ -#define CONFIG_AT91_LED - -/* - * SDRAM: 1 bank, min 32, max 128 MB - * Initialized before u-boot gets started. - */ -#define CONFIG_NR_DRAM_BANKS 1 -#define CONFIG_SYS_SDRAM_BASE 0x20000000 /* ATMEL_BASE_CS1 */ -#define CONFIG_SYS_SDRAM_SIZE 0x04000000 - -#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x00100000) -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01E00000) -#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x00100000) - -/* - * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM, - * leaving the correct space for initial global data structure above - * that address while providing maximum stack area below. - */ -#define CONFIG_SYS_INIT_SP_ADDR \ - (ATMEL_BASE_SRAM0 + 0x1000 - GENERATED_GBL_DATA_SIZE) - -/* DataFlash */ -#ifdef CONFIG_SYS_USE_DATAFLASH -# define CONFIG_ATMEL_DATAFLASH_SPI -# define CONFIG_HAS_DATAFLASH -# define CONFIG_SYS_SPI_WRITE_TOUT (5 * CONFIG_SYS_HZ) -# define CONFIG_SYS_MAX_DATAFLASH_BANKS 1 -# define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */ -# define AT91_SPI_CLK 15000000 -# define DATAFLASH_TCSS (0x1a << 16) -# define DATAFLASH_TCHS (0x1 << 24) -#endif - -/* NOR flash is not populated, disable it */ -#define CONFIG_SYS_NO_FLASH - -/* NAND flash */ -#ifdef CONFIG_CMD_NAND -# define CONFIG_NAND_ATMEL -# define CONFIG_SYS_MAX_NAND_DEVICE 1 -# define CONFIG_SYS_NAND_BASE 0x40000000 /* ATMEL_BASE_CS3 */ -# define CONFIG_SYS_NAND_DBW_8 -# define CONFIG_SYS_NAND_MASK_ALE (1 << 21) -# define CONFIG_SYS_NAND_MASK_CLE (1 << 22) -# define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(15) -# define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PA(22) -#endif - -/* Ethernet */ -#define CONFIG_MACB -#define CONFIG_RMII -#define CONFIG_FIT -#define CONFIG_NET_RETRY_COUNT 20 -#undef CONFIG_RESET_PHY_R - -/* USB */ -#define CONFIG_USB_ATMEL -#define CONFIG_USB_ATMEL_CLK_SEL_PLLB -#define CONFIG_USB_OHCI_NEW -#define CONFIG_DOS_PARTITION -#define CONFIG_SYS_USB_OHCI_CPU_INIT -#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00a00000 -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9263" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 -#define CONFIG_USB_STORAGE -#define CONFIG_CMD_FAT - -/* CAN */ -#define CONFIG_AT91_CAN - -/* hw-controller addresses */ -#define CONFIG_ET1100_BASE 0x70000000 /* ATMEL_BASE_CS6 */ - -#ifdef CONFIG_SYS_USE_DATAFLASH - -/* bootstrap + u-boot + env in dataflash on CS0 */ -# define CONFIG_ENV_IS_IN_DATAFLASH -# define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \ - 0x8400) -# define CONFIG_ENV_OFFSET 0x4200 -# define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \ - CONFIG_ENV_OFFSET) -# define CONFIG_ENV_SIZE 0x4200 - -#elif CONFIG_SYS_USE_NANDFLASH - -/* bootstrap + u-boot + env + linux in nandflash */ -# define CONFIG_ENV_IS_IN_NAND 1 -# define CONFIG_ENV_OFFSET 0xC0000 -# define CONFIG_ENV_SIZE 0x20000 - -#endif - -#define CONFIG_SYS_CBSIZE 512 -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ - sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_LONGHELP -#define CONFIG_CMDLINE_EDITING - -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + \ - 128*1024, 0x1000) - -#endif |