diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/inka4x0.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/inka4x0.h | 419 |
1 files changed, 419 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/inka4x0.h b/qemu/roms/u-boot/include/configs/inka4x0.h new file mode 100644 index 000000000..f321975c4 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/inka4x0.h @@ -0,0 +1,419 @@ +/* + * (C) Copyright 2009 + * Detlev Zundel, DENX Software Engineering, dzu@denx.de. + * + * (C) Copyright 2003-2005 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ +#define CONFIG_INKA4X0 1 /* INKA4x0 board */ + +/* + * Valid values for CONFIG_SYS_TEXT_BASE are: + * 0xFFE00000 boot low + * 0x00100000 boot from RAM (for testing only) + */ +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xFFE00000 /* Standard: boot low */ +#endif +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc5xxx/u-boot-customlayout.lds" + +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ + +#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ + +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* + * PCI Mapping: + * 0x40000000 - 0x4fffffff - PCI Memory + * 0x50000000 - 0x50ffffff - PCI IO Space + */ +#define CONFIG_PCI 1 +#define CONFIG_PCI_PNP 1 +#define CONFIG_PCI_SCAN_SHOW 1 +#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 + +#define CONFIG_PCI_MEM_BUS 0x40000000 +#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS +#define CONFIG_PCI_MEM_SIZE 0x10000000 + +#define CONFIG_PCI_IO_BUS 0x50000000 +#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS +#define CONFIG_PCI_IO_SIZE 0x01000000 + +#define CONFIG_SYS_XLB_PIPELINING 1 + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_IDE +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_SNTP +#define CONFIG_CMD_USB + +#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ + +#if (CONFIG_SYS_TEXT_BASE == 0xFFE00000) /* Boot low */ +# define CONFIG_SYS_LOWBOOT 1 +#endif + +/* + * Autobooting + */ +#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_ETHADDR 00:a0:a4:03:00:00 +#define CONFIG_OVERWRITE_ETHADDR_ONCE + +#define CONFIG_IPADDR 192.168.100.2 +#define CONFIG_SERVERIP 192.168.100.1 +#define CONFIG_NETMASK 255.255.255.0 +#define HOSTNAME inka4x0 +#define CONFIG_BOOTFILE "/tftpboot/inka4x0/uImage" +#define CONFIG_ROOTPATH "/opt/eldk/ppc_6xx" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addcons=setenv bootargs ${bootargs} " \ + "console=ttyS0,${baudrate}\0" \ + "flash_nfs=run nfsargs addip addcons;" \ + "bootm ${kernel_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};" \ + "run nfsargs addip addcons;bootm\0" \ + "enable_disp=mw.l 100000 04000000 1;" \ + "cp.l 100000 f0000b20 1;" \ + "cp.l 100000 f0000b28 1\0" \ + "ideargs=setenv bootargs root=/dev/hda1 rw\0" \ + "ide_boot=ext2load ide 0:1 200000 uImage;" \ + "run ideargs addip addcons enable_disp;bootm\0" \ + "brightness=255\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run ide_boot" + +/* + * IPB Bus clocking configuration. + */ +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ + +/* + * Flash configuration + */ +#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CONFIG_FLASH_CFI_DRIVER 1 +#define CONFIG_SYS_FLASH_BASE 0xffe00000 +#define CONFIG_SYS_FLASH_SIZE 0x00200000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ + +/* + * Environment settings + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x4000) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 +#define CONFIG_ENV_OVERWRITE 1 +#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ + +/* + * Memory map + */ +#define CONFIG_SYS_MBAR 0xF0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 + +/* + * SDRAM controller configuration + */ +#undef CONFIG_SDR_MT48LC16M16A2 +#undef CONFIG_DDR_MT46V16M16 +#undef CONFIG_DDR_MT46V32M16 +#undef CONFIG_DDR_HYB25D512160BF +#define CONFIG_DDR_K4H511638C + +/* Use ON-Chip SRAM until RAM will be available */ +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM + +/* preserve space for the post_word at end of on-chip SRAM */ +#define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4) + +#ifdef CONFIG_POST +#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE +#else +#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE +#endif + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 +#endif + +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +#define CONFIG_MPC5xxx_FEC_MII100 +/* + * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb + */ +/* #define CONFIG_MPC5xxx_FEC_MII10 */ +#define CONFIG_PHY_ADDR 0x00 +#define CONFIG_MII + +/* + * GPIO configuration + * + * use CS1 as gpio_wkup_6 output + * Bit 0 (mask: 0x80000000): 0 + * use ALT CAN position: Bits 2-3 (mask: 0x30000000): + * 00 -> No Alternatives, I2C1 is used for onboard EEPROM + * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1 do not use on TQM5200 with onboard + * EEPROM + * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100 + * use PSC2 as UART: Bits 24-27 (mask: 0x00000070): 0100 + * use PSC3 as UART: Bits 20-23 (mask: 0x00000700): 0100 + * use PSC6 as UART: Bits 9-11 (mask: 0x00700000): 0101 + */ +#define CONFIG_SYS_GPS_PORT_CONFIG 0x01501444 + +/* + * RTC configuration + */ +#define CONFIG_RTC_RTC4543 1 /* use external RTC */ + +/* + * Software (bit-bang) three wire serial configuration + * + * Note that we need the ifdefs because otherwise compilation of + * mkimage.c fails. + */ +#define CONFIG_SOFT_TWS 1 + +#ifdef TWS_IMPLEMENTATION +#include <mpc5xxx.h> +#include <asm/io.h> + +#define TWS_CE MPC5XXX_GPIO_WKUP_PSC1_4 /* GPIO_WKUP_0 */ +#define TWS_WR MPC5XXX_GPIO_WKUP_PSC2_4 /* GPIO_WKUP_1 */ +#define TWS_DATA MPC5XXX_GPIO_SINT_PSC3_4 /* GPIO_SINT_0 */ +#define TWS_CLK MPC5XXX_GPIO_SINT_PSC3_5 /* GPIO_SINT_1 */ + +static inline void tws_ce(unsigned bit) +{ + struct mpc5xxx_wu_gpio *wu_gpio = + (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO; + if (bit) + setbits_8(&wu_gpio->dvo, TWS_CE); + else + clrbits_8(&wu_gpio->dvo, TWS_CE); +} + +static inline void tws_wr(unsigned bit) +{ + struct mpc5xxx_wu_gpio *wu_gpio = + (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO; + if (bit) + setbits_8(&wu_gpio->dvo, TWS_WR); + else + clrbits_8(&wu_gpio->dvo, TWS_WR); +} + +static inline void tws_clk(unsigned bit) +{ + struct mpc5xxx_gpio *gpio = + (struct mpc5xxx_gpio *)MPC5XXX_GPIO; + if (bit) + setbits_8(&gpio->sint_dvo, TWS_CLK); + else + clrbits_8(&gpio->sint_dvo, TWS_CLK); +} + +static inline void tws_data(unsigned bit) +{ + struct mpc5xxx_gpio *gpio = + (struct mpc5xxx_gpio *)MPC5XXX_GPIO; + if (bit) + setbits_8(&gpio->sint_dvo, TWS_DATA); + else + clrbits_8(&gpio->sint_dvo, TWS_DATA); +} + +static inline unsigned tws_data_read(void) +{ + struct mpc5xxx_gpio *gpio = + (struct mpc5xxx_gpio *)MPC5XXX_GPIO; + return !!(in_8(&gpio->sint_ival) & TWS_DATA); +} + +static inline void tws_data_config_output(unsigned output) +{ + struct mpc5xxx_gpio *gpio = + (struct mpc5xxx_gpio *)MPC5XXX_GPIO; + if (output) + setbits_8(&gpio->sint_ddr, TWS_DATA); + else + clrbits_8(&gpio->sint_ddr, TWS_DATA); +} +#endif /* TWS_IMPLEMENTATION */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* Enable an alternate, more extensive memory test */ +#define CONFIG_SYS_ALT_MEMTEST + +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ + +/* + * Enable loopw command. + */ +#define CONFIG_LOOPW + +/* + * Various low-level settings + */ +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE + +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_BOOTCS_CFG 0x00087800 /* for pci_clk = 66 MHz */ +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE + +/* 32Mbit SRAM @0x30000000 */ +#define CONFIG_SYS_CS1_START 0x30000000 +#define CONFIG_SYS_CS1_SIZE 0x00400000 +#define CONFIG_SYS_CS1_CFG 0x31800 /* for pci_clk = 33 MHz */ + +/* 2 quad UART @0x80000000 (MBAR is relocated to 0xF0000000) */ +#define CONFIG_SYS_CS2_START 0x80000000 +#define CONFIG_SYS_CS2_SIZE 0x0001000 +#define CONFIG_SYS_CS2_CFG 0x21800 /* for pci_clk = 33 MHz */ + +/* GPIO in @0x30400000 */ +#define CONFIG_SYS_CS3_START 0x30400000 +#define CONFIG_SYS_CS3_SIZE 0x00100000 +#define CONFIG_SYS_CS3_CFG 0x31800 /* for pci_clk = 33 MHz */ + +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 + +/*----------------------------------------------------------------------- + * USB stuff + *----------------------------------------------------------------------- + */ +#define CONFIG_USB_OHCI +#define CONFIG_USB_CLOCK 0x00015555 +#define CONFIG_USB_CONFIG 0x00001000 +#define CONFIG_USB_STORAGE + +/*----------------------------------------------------------------------- + * IDE/ATA stuff Supports IDE harddisk + *----------------------------------------------------------------------- + */ + +#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ + +#define CONFIG_IDE_PREINIT + +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 1 drive per IDE bus */ + +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0060 /* Offset for data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) /* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x005C /* Offset for alternate registers */ +#define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ + +#define CONFIG_ATAPI 1 + +#define CONFIG_SYS_BRIGHTNESS 0xFF /* LCD Default Brightness (255 = off) */ + +#endif /* __CONFIG_H */ |