diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/cogent_mpc8260.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/cogent_mpc8260.h | 392 |
1 files changed, 392 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/cogent_mpc8260.h b/qemu/roms/u-boot/include/configs/cogent_mpc8260.h new file mode 100644 index 000000000..02b25c644 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/cogent_mpc8260.h @@ -0,0 +1,392 @@ +/* + * (C) Copyright 2000 + * Murray Jensen <Murray.Jensen@cmst.csiro.au> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * Config header file for Cogent platform using an MPC8xx CPU module + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ +#define CONFIG_COGENT 1 /* using Cogent Modular Architecture */ +#define CONFIG_CPM2 1 /* Has a CPM2 */ + +#define CONFIG_SYS_TEXT_BASE 0xfff00000 + +#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ +#define CONFIG_MISC_INIT_R /* Use misc_init_r() */ + +/* Cogent Modular Architecture options */ +#define CONFIG_CMA282 1 /* ...on a CMA282 CPU module */ +#define CONFIG_CMA111 1 /* ...on a CMA111 motherboard */ + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere (for example, on the cogent platform, there are serial + * ports on the motherboard which are used for the serial console - see + * cogent/cma101/serial.[ch]). + */ +#define CONFIG_CONS_ON_SMC /* define if console on SMC */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else*/ +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ +#undef CONFIG_CONS_USE_EXTC /* SMC/SCC use ext clock not brg_clk */ +#define CONFIG_CONS_EXTC_RATE 3686400 /* SMC/SCC ext clk rate in Hz */ +#define CONFIG_CONS_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9,1=CLK5/CLK15*/ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. + */ +#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#undef CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#define CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 1 /* which channel for ether */ + +/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ +#define CONFIG_8260_CLKIN 66666666 /* in Hz */ + +#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC) +#define CONFIG_BAUDRATE 230400 +#else +#define CONFIG_BAUDRATE 9600 +#endif + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_KGDB + +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_NFS + +#ifdef DEBUG +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif +#define CONFIG_BOOTCOMMAND "bootm 04080000 04200000" /* autoboot command*/ + +#define CONFIG_BOOTARGS "root=/dev/ram rw" + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */ +#undef CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */ +#undef CONFIG_KGDB_NONE /* define if kgdb on something else */ +#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */ +#define CONFIG_KGDB_USE_EXTC /* SMC/SCC use ext clock not brg_clk */ +#define CONFIG_KGDB_EXTC_RATE 3686400 /* serial ext clk rate in Hz */ +#define CONFIG_KGDB_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9,1=CLK5/CLK15*/ +# if defined(CONFIG_KGDB_NONE) || defined(CONFIG_KGDB_USE_EXTC) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port at */ +# else +#define CONFIG_KGDB_BAUDRATE 9600 /* speed to run kgdb serial port at */ +# endif +#endif + +#undef CONFIG_WATCHDOG /* disable platform specific watchdog */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x01c00000 /* 4 ... 28 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ + +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +/*----------------------------------------------------------------------- + * Low Level Cogent settings + * if CONFIG_SYS_CMA_CONS_SERIAL is defined, make sure the 8260 CPM serial is not. + * also, make sure CONFIG_CONS_INDEX is still defined - the index will be + * 1 for serialA, 2 for serialB, 3 for ser2A, 4 for ser2B + * (second 2 for CMA120 only) + */ +#define CONFIG_SYS_CMA_MB_BASE 0x00000000 /* base of m/b address space */ + +#include <configs/cogent_common.h> + +#ifdef CONFIG_CONS_NONE +#define CONFIG_SYS_CMA_CONS_SERIAL /* use Cogent motherboard serial for console */ +#endif +#define CONFIG_SYS_CMA_LCD_HEARTBEAT /* define for sec rotator in lcd corner */ +#define CONFIG_SHOW_ACTIVITY + +#if (CMA_MB_CAPS & CMA_MB_CAP_FLASH) +/* + * flash exists on the motherboard + * set these four according to TOP dipsw: + * TOP on => ..._FLLOW_... (boot EPROM space is high so FLASH is low ) + * TOP off => ..._FLHIGH_... (boot EPROM space is low so FLASH is high) + */ +#define CMA_MB_FLASH_EXEC_BASE CMA_MB_FLLOW_EXEC_BASE +#define CMA_MB_FLASH_EXEC_SIZE CMA_MB_FLLOW_EXEC_SIZE +#define CMA_MB_FLASH_RDWR_BASE CMA_MB_FLLOW_RDWR_BASE +#define CMA_MB_FLASH_RDWR_SIZE CMA_MB_FLLOW_RDWR_SIZE +#endif +#define CMA_MB_FLASH_BASE CMA_MB_FLASH_EXEC_BASE +#define CMA_MB_FLASH_SIZE CMA_MB_FLASH_EXEC_SIZE + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + * + * if you change bits in the HRCW, you must also change the CONFIG_SYS_* + * defines for the various registers affected by the HRCW e.g. changing + * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR. + */ +#define CONFIG_SYS_HRCW_MASTER (HRCW_EBM|HRCW_BPS10|HRCW_L2CPC10|HRCW_DPPC11|\ + HRCW_ISB100|HRCW_MMR11|HRCW_MODCK_H0101) +/* no slaves so just duplicate the master hrcw */ +#define CONFIG_SYS_HRCW_SLAVE1 CONFIG_SYS_HRCW_MASTER +#define CONFIG_SYS_HRCW_SLAVE2 CONFIG_SYS_HRCW_MASTER +#define CONFIG_SYS_HRCW_SLAVE3 CONFIG_SYS_HRCW_MASTER +#define CONFIG_SYS_HRCW_SLAVE4 CONFIG_SYS_HRCW_MASTER +#define CONFIG_SYS_HRCW_SLAVE5 CONFIG_SYS_HRCW_MASTER +#define CONFIG_SYS_HRCW_SLAVE6 CONFIG_SYS_HRCW_MASTER +#define CONFIG_SYS_HRCW_SLAVE7 CONFIG_SYS_HRCW_MASTER + +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CONFIG_SYS_IMMR 0xF0000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE CMA_MB_RAM_BASE +#ifdef CONFIG_CMA302 +#define CONFIG_SYS_FLASH_BASE CMA_MB_SLOT2_BASE /* cma302 in slot 2 */ +#else +#define CONFIG_SYS_FLASH_BASE CMA_MB_FLASH_BASE /* flash on m/b */ +#endif +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max num of sects on one chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Flash Erase Timeout (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR CONFIG_SYS_FLASH_BASE /* Addr of Environment Sector */ +#ifdef CONFIG_CMA302 +#define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ +#define CONFIG_ENV_SECT_SIZE (512*1024) /* see README - env sect real size */ +#else +#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ +#endif + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value*/ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\ + HID0_IFEM|HID0_ABE) +#define CONFIG_SYS_HID0_FINAL (HID0_ICE|HID0_IFEM|HID0_ABE) +#define CONFIG_SYS_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register 5-5 + *----------------------------------------------------------------------- + * turn on Checkstop Reset Enable + */ +#define CONFIG_SYS_RMR RMR_CSRE + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_BCR BCR_EBM + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC11|SIUMCR_L2CPC10|SIUMCR_MMR11) + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 4-35 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#if defined(CONFIG_WATCHDOG) +#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) +#else +#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP) +#endif /* CONFIG_WATCHDOG */ + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + * Ensure DFBRG is Divide by 16 + */ +#define CONFIG_SYS_SCCR (SCCR_DFBRG01) + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_RCCR 0 + +#if defined(CONFIG_CMA282) + +/* + * Init Memory Controller: + * + * According to the Cogent manual, only CS0 and CS2 are used - CS0 for EPROM + * and CS2 for (optional) local bus RAM on the CPU module. + * + * Note the motherboard address space (256 Mbyte in size) is connected + * to the 60x Bus and is located starting at address 0. The Hard Reset + * Configuration Word should put the 60x Bus into External Bus Mode, since + * we dont set up any memory controller maps for it (see BCR[EBM], 4-26). + * + * (the *_SIZE vars must be a power of 2) + */ + +#define CONFIG_SYS_CMA_CS0_BASE CONFIG_SYS_TEXT_BASE /* EPROM */ +#define CONFIG_SYS_CMA_CS0_SIZE (1 << 20) +#if 0 +#define CONFIG_SYS_CMA_CS2_BASE 0x10000000 /* Local Bus SDRAM */ +#define CONFIG_SYS_CMA_CS2_SIZE (16 << 20) +#endif + +/* + * CS0 maps the EPROM on the cpu module + * Set it for 10 wait states, address CONFIG_SYS_MONITOR_BASE and size 1M + * + * Note: We must have already transferred control to the final location + * of the EPROM before these are used, because when BR0/OR0 are set, the + * mirror of the eprom at any other addresses will disappear. + */ + +/* base address = CONFIG_SYS_CMA_CS0_BASE, 16-bit, no parity, r/o, gpcm (60x bus) */ +#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_CMA_CS0_BASE&BRx_BA_MSK)|BRx_PS_16|BRx_WP|BRx_V) +/* mask size CONFIG_SYS_CMA_CS0_SIZE, csneg 1/4 early, adr-to-cs 1/2, 10-wait states */ +#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_CMA_CS0_SIZE)|\ + ORxG_CSNT|ORxG_ACS_DIV2|ORxG_SCY_10_CLK) + +/* + * CS2 enables the Local Bus SDRAM on the CPU Module + * + * Will leave this unset for the moment, because a) my CPU module has no + * SDRAM installed (it is optional); and b) it will require programming + * one of the UPMs in SDRAM mode - not a trivial job, and hard to get right + * if you can't test it. + */ + +#if 0 +/* base address = CONFIG_SYS_CMA_CS2_BASE, 32-bit, no parity, ??? */ +#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_CMA_CS2_BASE&BRx_BA_MSK)|BRx_PS_32|/*???*/|BRx_V) +/* mask size CONFIG_SYS_CMA_CS2_SIZE, CS time normal, ??? */ +#define CONFIG_SYS_OR2_PRELIM ((~(CONFIG_SYS_CMA_CS2_SIZE-1)&ORx_AM_MSK)|/*???*/) +#endif + +#endif +#endif /* __CONFIG_H */ |