diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/W7OLMG.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/W7OLMG.h | 317 |
1 files changed, 317 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/W7OLMG.h b/qemu/roms/u-boot/include/configs/W7OLMG.h new file mode 100644 index 000000000..2a38116dd --- /dev/null +++ b/qemu/roms/u-boot/include/configs/W7OLMG.h @@ -0,0 +1,317 @@ +/* + * (C) Copyright 2001 + * Erik Theisen, Wave 7 Optics, etheisen@mindspring.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_405GP 1 /* This is a PPC405GP CPU */ +#define CONFIG_W7O 1 /* ...on a Wave 7 Optics board */ +#define CONFIG_W7OLMG 1 /* ...specifically an LMG */ + +#define CONFIG_SYS_TEXT_BASE 0xFFFC0000 + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_F 1 /* and misc_init_f() */ +#define CONFIG_MISC_INIT_R 1 /* and misc_init_r() */ + +#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ + +#define CONFIG_BAUDRATE 9600 +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ + +#if 1 +#define CONFIG_BOOTCOMMAND "bootvx" /* VxWorks boot command */ +#else +#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ +#endif + +#undef CONFIG_BOOTARGS + +#define CONFIG_LOADADDR F0080000 + +#define CONFIG_ETHADDR 00:06:0D:00:00:00 /* Default, overridden at boot */ +#define CONFIG_OVERWRITE_ETHADDR_ONCE +#define CONFIG_IPADDR 192.168.1.1 +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_SERVERIP 192.168.1.2 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* disallow baudrate change */ + +#define CONFIG_PPC4xx_EMAC +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0 /* PHY address */ + +#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_SENSORS {2, 4} /* Sensor addresses */ +#define CONFIG_SYS_DTT_MAX_TEMP 70 +#define CONFIG_SYS_DTT_LOW_TEMP -30 +#define CONFIG_SYS_DTT_HYSTERESIS 3 + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PCI +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_BEDBUG +#define CONFIG_CMD_DATE +#define CONFIG_CMD_I2C +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_BSP +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_DTT + + +#undef CONFIG_WATCHDOG /* watchdog disabled */ +#define CONFIG_HW_WATCHDOG /* HW Watchdog, board specific */ + +#define CONFIG_SPD_EEPROM /* SPD EEPROM for SDRAM param. */ +#define CONFIG_SPDDRAM_SILENT /* No output if spd fails */ +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "Wave7Optics> " /* Monitor Command Prompt */ +#undef CONFIG_SYS_HUSH_PARSER /* No hush parse for U-Boot */ +#ifdef CONFIG_SYS_HUSH_PARSER +#endif +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ +#define CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ +#define CONFIG_SYS_BASE_BAUD 384000 + + +/* The following table includes the supported baudrates */ +#define CONFIG_SYS_BAUDRATE_TABLE {9600} + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* use extended board_info (bd_t) */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ +#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ +#define CONFIG_PCI_PNP /* pci plug-and-play */ +/* resource configuration */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0156 /* PCI Device ID: 405GP */ +#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ +#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ +#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ +#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ + +/*----------------------------------------------------------------------- + * Set up values for external bus controller + * used by cpu_init.c + *----------------------------------------------------------------------- + */ + /* use PerWE instead of PCI_INT ( these functions share a pin ) */ +#define CONFIG_USE_PERWE 1 + +/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ +#define CONFIG_SYS_TEMP_STACK_OCM 1 + +/* bank 0 is boot flash */ +/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ +#define CONFIG_SYS_W7O_EBC_PB0AP 0x03050440 +/* BAS=0xFFE,BS=0x1(2MB),BU=0x3(R/W),BW=0x0(8 bits) */ +#define CONFIG_SYS_W7O_EBC_PB0CR 0xFFE38000 + +/* bank 1 is main flash */ +/* BME=0,TWT=9,CSN=1,OEN=1,WBN=0,WBF=0,TH=1,RE=0,SOR=0,BEM=1,PEN=0 */ +#define CONFIG_SYS_EBC_PB1AP 0x04850240 +/* BAS=0xF00,BS=0x7(128MB),BU=0x3(R/W),BW=0x10(32 bits) */ +#define CONFIG_SYS_EBC_PB1CR 0xF00FC000 + +/* bank 2 is RTC/NVRAM */ +/* BME=0,TWT=6,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ +#define CONFIG_SYS_EBC_PB2AP 0x03000440 +/* BAS=0xFC0,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */ +#define CONFIG_SYS_EBC_PB2CR 0xFC018000 + +/* bank 3 is FPGA 0 */ +/* BME=0,TWT=4,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=0,PEN=0 */ +#define CONFIG_SYS_EBC_PB3AP 0x02000400 +/* BAS=0xFD0,BS=0x0(1MB),BU=0x3(R/W),BW=0x1(16 bits) */ +#define CONFIG_SYS_EBC_PB3CR 0xFD01A000 + +/* bank 4 is SAM 8 bit range */ +/* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */ +#define CONFIG_SYS_EBC_PB4AP 0x02840380 +/* BAS=,BS=,BU=0x3(R/W),BW=0x0(8 bits) */ +#define CONFIG_SYS_EBC_PB4CR 0xFE878000 + +/* bank 5 is SAM 16 bit range */ +/* BME=0,TWT=10,CSN=2,OEN=0,WBN=0,WBF=0,TH=6,RE=1,SOR=1,BEM=0,PEN=0 */ +#define CONFIG_SYS_EBC_PB5AP 0x05040d80 +/* BAS=,BS=,BU=0x3(R/W),BW=0x1(16 bits) */ +#define CONFIG_SYS_EBC_PB5CR 0xFD87A000 + +/* bank 6 is unused */ +/* PB6AP = 0 */ +#define CONFIG_SYS_EBC_PB6AP 0x00000000 +/* PB6CR = 0 */ +#define CONFIG_SYS_EBC_PB6CR 0x00000000 + +/* bank 7 is LED register */ +/* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ +#define CONFIG_SYS_W7O_EBC_PB7AP 0x03050440 +/* BAS=0xFE0,BS=0x0(1MB),BU=0x3(R/W),BW=0x2(32 bits) */ +#define CONFIG_SYS_W7O_EBC_PB7CR 0xFE01C000 + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0xFFFC0000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 196 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sec on 1 chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout, Flash Erase, in ms */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout, Flash Write, in ms */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use real Flash protection */ + +#if 1 /* Use NVRAM for environment variables */ +/*----------------------------------------------------------------------- + * NVRAM organization + */ +#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for env vars */ +#define CONFIG_SYS_NVRAM_BASE_ADDR 0xfc000000 /* NVRAM base address */ +#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */ +#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */ +/*define CONFIG_ENV_ADDR \ + (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) Env */ +#define CONFIG_ENV_ADDR CONFIG_SYS_NVRAM_BASE_ADDR + +#else /* Use Boot Flash for environment variables */ +/*----------------------------------------------------------------------- + * Flash EEPROM for environment + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */ +#define CONFIG_ENV_SIZE 0x10000 /* Total Size of env. sector */ + +#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sec tot sze */ +#endif + +/*----------------------------------------------------------------------- + * I2C EEPROM (ATMEL 24C04N) + */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F + +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM ATMEL 24C04N */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_I2C_MULTI_EEPROMS +/*----------------------------------------------------------------------- + * Definitions for Serial Presence Detect EEPROM address + * (to get SDRAM settings) + */ +#define SPD_EEPROM_ADDRESS 0x50 /* XXX conflicting address!!! XXX */ + +/* + * Init Memory Controller: + */ +#define FLASH_BASE0_PRELIM 0xFFE00000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0xF0000000 /* FLASH bank #1 */ + +/* On Chip Memory location */ +#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 +#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in RAM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ +#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#endif + +/* + * FPGA(s) configuration + */ +#define CONFIG_SYS_FPGA_IMAGE_LEN 0x80000 /* 512KB FPGA image */ +#define CONFIG_NUM_FPGAS 1 /* Number of FPGAs on board */ +#define CONFIG_MAX_FPGAS 6 /* Maximum number of FPGAs */ +#define CONFIG_FPGAS_BASE 0xFD000000L /* Base address of FPGAs */ +#define CONFIG_FPGAS_BANK_SIZE 0x00100000L /* FPGAs' mmap bank size */ + +#endif /* __CONFIG_H */ |