diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/PMC440.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/PMC440.h | 427 |
1 files changed, 0 insertions, 427 deletions
diff --git a/qemu/roms/u-boot/include/configs/PMC440.h b/qemu/roms/u-boot/include/configs/PMC440.h deleted file mode 100644 index c5e2f164c..000000000 --- a/qemu/roms/u-boot/include/configs/PMC440.h +++ /dev/null @@ -1,427 +0,0 @@ -/* - * (C) Copyright 2007-2008 - * Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com. - * Based on the sequoia configuration file. - * - * (C) Copyright 2006-2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2006 - * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com - * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/************************************************************************ - * PMC440.h - configuration for esd PMC440 boards - ***********************************************************************/ -#ifndef __CONFIG_H -#define __CONFIG_H - -/*----------------------------------------------------------------------- - * High Level Configuration Options - *----------------------------------------------------------------------*/ -#define CONFIG_440EPX 1 /* Specific PPC440EPx */ -#define CONFIG_440 1 /* ... PPC440 family */ - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFF90000 -#endif - -#define CONFIG_SYS_CLK_FREQ 33333400 - -#if 0 /* temporary disabled because OS/9 does not like dcache on startup */ -#define CONFIG_4xx_DCACHE /* enable dcache */ -#endif - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_MISC_INIT_F 1 -#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ -#define CONFIG_BOARD_TYPES 1 /* support board types */ -/*----------------------------------------------------------------------- - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MONITOR_LEN (~(CONFIG_SYS_TEXT_BASE) + 1) -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserve 256 kB for malloc() */ - -#define CONFIG_PRAM 0 /* use pram variable to overwrite */ - -#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_NAND_ADDR 0xd0000000 /* NAND Flash */ -#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */ -#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_OCM_BASE -#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */ -#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 -#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 -#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 -#define CONFIG_SYS_PCI_MEMSIZE 0x80000000 /* 2GB! */ - -#define CONFIG_SYS_USB2D0_BASE 0xe0000100 -#define CONFIG_SYS_USB_DEVICE 0xe0000000 -#define CONFIG_SYS_USB_HOST 0xe0000400 -#define CONFIG_SYS_FPGA_BASE0 0xef000000 /* 32 bit */ -#define CONFIG_SYS_FPGA_BASE1 0xef100000 /* 16 bit */ -#define CONFIG_SYS_RESET_BASE 0xef200000 - -/*----------------------------------------------------------------------- - * Initial RAM & stack pointer - *----------------------------------------------------------------------*/ -/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */ -#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) - -/*----------------------------------------------------------------------- - * Serial Port - *----------------------------------------------------------------------*/ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() -#undef CONFIG_SYS_EXT_SERIAL_CLOCK -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ -#define CONFIG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */ - -/*----------------------------------------------------------------------- - * RTC - *----------------------------------------------------------------------*/ -#define CONFIG_RTC_RX8025 - -/*----------------------------------------------------------------------- - * FLASH related - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ - -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -#endif - -#ifdef CONFIG_ENV_IS_IN_EEPROM -#define CONFIG_ENV_OFFSET 0 /* environment starts at the beginning of the EEPROM */ -#define CONFIG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env vars */ -#endif - -/*----------------------------------------------------------------------- - * DDR SDRAM - *----------------------------------------------------------------------*/ -#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ -#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ - /* 440EPx errata CHIP 11 */ - -/*----------------------------------------------------------------------- - * I2C - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F -#define CONFIG_SYS_I2C_PPC4XX_CH1 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_1 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_1 0x7F - -#define CONFIG_SYS_I2C_MULTI_EEPROMS - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01 - -#define CONFIG_SYS_EEPROM_WREN 1 -#define CONFIG_SYS_I2C_BOOT_EEPROM_ADDR 0x52 - -/* - * standard dtt sensor configuration - bottom bit will determine local or - * remote sensor of the TMP401 - */ -#define CONFIG_DTT_SENSORS { 0, 1 } - -/* - * The PMC440 uses a TI TMP401 temperature sensor. This part - * is basically compatible to the ADM1021 that is supported - * by U-Boot. - * - * - i2c addr 0x4c - * - conversion rate 0x02 = 0.25 conversions/second - * - ALERT ouput disabled - * - local temp sensor enabled, min set to 0 deg, max set to 70 deg - * - remote temp sensor enabled, min set to 0 deg, max set to 70 deg - */ -#define CONFIG_DTT_ADM1021 -#define CONFIG_SYS_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} } - -#define CONFIG_PREBOOT "echo Add \\\"run fpga\\\" and " \ - "\\\"painit\\\" to preboot command" - -#undef CONFIG_BOOTARGS - -/* Setup some board specific values for the default environment variables */ -#define CONFIG_HOSTNAME pmc440 -#define CONFIG_SYS_BOOTFILE "bootfile=/tftpboot/pmc440/uImage\0" -#define CONFIG_SYS_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_SYS_BOOTFILE \ - CONFIG_SYS_ROOTPATH \ - "fdt_file=/tftpboot/pmc440/pmc440.dtb\0" \ - "netdev=eth0\0" \ - "ethrotate=no\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ - "addmisc=setenv bootargs ${bootargs} mem=${mem}\0" \ - "nandargs=setenv bootargs root=/dev/mtdblock6 rootfstype=jffs2 rw\0" \ - "nand_boot_fdt=run nandargs addip addtty addmisc;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "net_nfs_fdt=tftp ${kernel_addr_r} ${bootfile};" \ - "tftp ${fdt_addr_r} ${fdt_file};" \ - "run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "kernel_addr=ffc00000\0" \ - "kernel_addr_r=200000\0" \ - "fpga_addr=fff00000\0" \ - "fdt_addr=fff80000\0" \ - "fdt_addr_r=800000\0" \ - "fpga=fpga loadb 0 ${fpga_addr}\0" \ - "load=tftp 200000 /tftpboot/pmc440/u-boot.bin\0" \ - "update=protect off fff90000 ffffffff;era fff90000 ffffffff;" \ - "cp.b 200000 fff90000 70000\0" \ - "" - -#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ - -#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ - -#define CONFIG_HAS_ETH0 -#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ -#define CONFIG_PHY1_ADDR 1 -#define CONFIG_RESET_PHY_R 1 - -/* USB */ -#define CONFIG_USB_OHCI_NEW -#define CONFIG_USB_STORAGE -#define CONFIG_SYS_OHCI_BE_CONTROLLER - -#define CONFIG_SYS_USB_OHCI_BOARD_INIT 1 -#define CONFIG_SYS_USB_OHCI_CPU_INIT 1 -#define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 - -/* Comment this out to enable USB 1.1 device */ -#define USB_2_0_DEVICE - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - -#include <config_cmd_default.h> - -#define CONFIG_CMD_BSP -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DTT -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_MII -#define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_USB -#define CONFIG_CMD_REGINFO - -/* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_UART | \ - CONFIG_SYS_POST_I2C | \ - CONFIG_SYS_POST_CACHE | \ - CONFIG_SYS_POST_FPU | \ - CONFIG_SYS_POST_ETHER | \ - CONFIG_SYS_POST_SPR) - -#define CONFIG_LOGBUFFER -#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ - -#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ - -#define CONFIG_SUPPORT_VFAT - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -#define CONFIG_AUTOBOOT_KEYED 1 -#define CONFIG_AUTOBOOT_PROMPT \ - "Press SPACE to abort autoboot in %d seconds\n", bootdelay -#undef CONFIG_AUTOBOOT_DELAY_STR -#define CONFIG_AUTOBOOT_STOP_STR " " - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------*/ -/* General PCI */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */ -#define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */ - -/* Board-specific PCI */ -#define CONFIG_SYS_PCI_TARGET_INIT -#define CONFIG_SYS_PCI_MASTER_INIT -#define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ - -#define CONFIG_PCI_BOOTDELAY 0 - -/* PCI identification */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ -#define CONFIG_SYS_PCI_SUBSYS_ID_NONMONARCH 0x0441 /* PCI Device ID: Non-Monarch */ -#define CONFIG_SYS_PCI_SUBSYS_ID_MONARCH 0x0440 /* PCI Device ID: Monarch */ -/* for weak __pci_target_init() */ -#define CONFIG_SYS_PCI_SUBSYS_ID CONFIG_SYS_PCI_SUBSYS_ID_MONARCH -#define CONFIG_SYS_PCI_CLASSCODE_NONMONARCH PCI_CLASS_PROCESSOR_POWERPC -#define CONFIG_SYS_PCI_CLASSCODE_MONARCH PCI_CLASS_BRIDGE_HOST - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FPGA stuff - *----------------------------------------------------------------------*/ -#define CONFIG_FPGA -#define CONFIG_FPGA_XILINX -#define CONFIG_FPGA_SPARTAN2 -#define CONFIG_FPGA_SPARTAN3 - -#define CONFIG_FPGA_COUNT 2 -/*----------------------------------------------------------------------- - * External Bus Controller (EBC) Setup - *----------------------------------------------------------------------*/ - -/* - * On Sequoia CS0 and CS3 are switched when configuring for NAND booting - */ -#define CONFIG_SYS_NAND_CS 2 /* NAND chip connected to CSx */ - -/* Memory Bank 0 (NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x03017200 -#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xda000) - -/* Memory Bank 2 (NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x018003c0 -#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_NAND_ADDR | 0x1c000) - -/* Memory Bank 1 (RESET) initialization */ -#define CONFIG_SYS_EBC_PB1AP 0x7f817200 /* 0x03017200 */ -#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_RESET_BASE | 0x1c000) - -/* Memory Bank 4 (FPGA / 32Bit) initialization */ -#define CONFIG_SYS_EBC_PB4AP 0x03840f40 /* BME=0,TWT=7,CSN=1,TH=7,RE=1,SOR=0,BEM=1 */ -#define CONFIG_SYS_EBC_PB4CR (CONFIG_SYS_FPGA_BASE0 | 0x1c000) /* BS=1M,BU=R/W,BW=32bit */ - -/* Memory Bank 5 (FPGA / 16Bit) initialization */ -#define CONFIG_SYS_EBC_PB5AP 0x03840f40 /* BME=0,TWT=3,CSN=1,TH=0,RE=1,SOR=0,BEM=1 */ -#define CONFIG_SYS_EBC_PB5CR (CONFIG_SYS_FPGA_BASE1 | 0x1a000) /* BS=1M,BU=R/W,BW=16bit */ - -/*----------------------------------------------------------------------- - * NAND FLASH - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS) -#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ -#define CONFIG_SYS_NAND_QUIET_TEST 1 - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - -#define CONFIG_API 1 - -#endif /* __CONFIG_H */ |