diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/MUSENKI.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/MUSENKI.h | 275 |
1 files changed, 0 insertions, 275 deletions
diff --git a/qemu/roms/u-boot/include/configs/MUSENKI.h b/qemu/roms/u-boot/include/configs/MUSENKI.h deleted file mode 100644 index c5c929002..000000000 --- a/qemu/roms/u-boot/include/configs/MUSENKI.h +++ /dev/null @@ -1,275 +0,0 @@ -/* - * (C) Copyright 2001 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * - * Configuration settings for the MUSENKI board. - * - */ - -/* ------------------------------------------------------------------------- */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC8245 1 -#define CONFIG_MUSENKI 1 - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 9600 - -#define CONFIG_BOOTDELAY 5 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - - -/* - * Miscellaneous configurable options - */ -#undef CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ - -/* Print Buffer Size - */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_MAXARGS 8 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */ - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#undef CONFIG_PCI_PNP - - -#define CONFIG_TULIP - -#define PCI_ENET0_IOADDR 0x80000000 -#define PCI_ENET0_MEMADDR 0x80000000 -#define PCI_ENET1_IOADDR 0x81000000 -#define PCI_ENET1_MEMADDR 0x81000000 - - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -#define CONFIG_SYS_FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank on RCS#0 */ -#define CONFIG_SYS_FLASH_BASE1_PRELIM 0xFF000000 /* FLASH bank on RCS#1 */ -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH_BASE0_PRELIM - -/* even though FLASHP_BASE is FF800000, with 4MB is RCS0, the - * reset vector is actually located at FFB00100, but the 8245 - * takes care of us. - */ -#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 - -#define CONFIG_SYS_EUMB_ADDR 0xFC000000 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */ - - /* Maximum amount of RAM. - */ -#define CONFIG_SYS_MAX_RAM_SIZE 0x08000000 /* 0 .. 128 MB of (S)DRAM */ - - -#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE -#undef CONFIG_SYS_RAMBOOT -#else -#define CONFIG_SYS_RAMBOOT -#endif - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL - -#define CONFIG_SYS_NS16550_REG_SIZE 1 - -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4600) - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area - */ - -/* #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - * For the detail description refer to the MPC8240 user's manual. - */ - -#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ - - /* Bit-field values for MCCR1. - */ -#define CONFIG_SYS_ROMNAL 7 -#define CONFIG_SYS_ROMFAL 11 -#define CONFIG_SYS_DBUS_SIZE 0x3 - - /* Bit-field values for MCCR2. - */ -#define CONFIG_SYS_TSWAIT 0x5 /* Transaction Start Wait States timer */ -#define CONFIG_SYS_REFINT 0x400 /* Refresh interval FIXME: was 0t430 */ - - /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. - */ -#define CONFIG_SYS_BSTOPRE 121 - - /* Bit-field values for MCCR3. - */ -#define CONFIG_SYS_REFREC 8 /* Refresh to activate interval */ - - /* Bit-field values for MCCR4. - */ -#define CONFIG_SYS_PRETOACT 3 /* Precharge to activate interval FIXME: was 2 */ -#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval FIXME: was 5 */ -#define CONFIG_SYS_ACTORW 3 /* FIXME was 2 */ -#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latancy */ -#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */ -#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1 -#define CONFIG_SYS_EXTROM 1 -#define CONFIG_SYS_REGDIMM 0 - -#define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 reatins the currently accessed page in memory FIXME: was 0x32*/ - -#define CONFIG_SYS_SDRAM_DSCD 0x20 /* SDRAM data in sample clock delay - note bottom 3 bits MUST be 0 */ - -/* Memory bank settings. - * Only bits 20-29 are actually used from these vales to set the - * start/end addresses. The upper two bits will always be 0, and the lower - * 20 bits will be 0x00000 for a start address, or 0xfffff for an end - * address. Refer to the MPC8240 book. - */ - -#define CONFIG_SYS_BANK0_START 0x00000000 -#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1) -#define CONFIG_SYS_BANK0_ENABLE 1 -#define CONFIG_SYS_BANK1_START 0x3ff00000 -#define CONFIG_SYS_BANK1_END 0x3fffffff -#define CONFIG_SYS_BANK1_ENABLE 0 -#define CONFIG_SYS_BANK2_START 0x3ff00000 -#define CONFIG_SYS_BANK2_END 0x3fffffff -#define CONFIG_SYS_BANK2_ENABLE 0 -#define CONFIG_SYS_BANK3_START 0x3ff00000 -#define CONFIG_SYS_BANK3_END 0x3fffffff -#define CONFIG_SYS_BANK3_ENABLE 0 -#define CONFIG_SYS_BANK4_START 0x3ff00000 -#define CONFIG_SYS_BANK4_END 0x3fffffff -#define CONFIG_SYS_BANK4_ENABLE 0 -#define CONFIG_SYS_BANK5_START 0x3ff00000 -#define CONFIG_SYS_BANK5_END 0x3fffffff -#define CONFIG_SYS_BANK5_ENABLE 0 -#define CONFIG_SYS_BANK6_START 0x3ff00000 -#define CONFIG_SYS_BANK6_END 0x3fffffff -#define CONFIG_SYS_BANK6_ENABLE 0 -#define CONFIG_SYS_BANK7_START 0x3ff00000 -#define CONFIG_SYS_BANK7_END 0x3fffffff -#define CONFIG_SYS_BANK7_ENABLE 0 - -#define CONFIG_SYS_ODCR 0xff - -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* Max number of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors per flash */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - - - /* Warining: environment is not EMBEDDED in the U-Boot code. - * It's stored in flash separately. - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0xFFFF0000 -#define CONFIG_ENV_SIZE 0x00010000 /* Size of the Environment */ -#define CONFIG_ENV_SECT_SIZE 0x20000 /* Size of the Environment Sector */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -#endif /* __CONFIG_H */ |