diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/MPC8641HPCN.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/MPC8641HPCN.h | 756 |
1 files changed, 0 insertions, 756 deletions
diff --git a/qemu/roms/u-boot/include/configs/MPC8641HPCN.h b/qemu/roms/u-boot/include/configs/MPC8641HPCN.h deleted file mode 100644 index a0d7d5262..000000000 --- a/qemu/roms/u-boot/include/configs/MPC8641HPCN.h +++ /dev/null @@ -1,756 +0,0 @@ -/* - * Copyright 2006, 2010-2011 Freescale Semiconductor. - * - * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * MPC8641HPCN board configuration file - * - * Make sure you change the MAC address and other network params first, - * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_SYS_GENERIC_BOARD -#define CONFIG_DISPLAY_BOARDINFO - -/* High Level Configuration Options */ -#define CONFIG_MPC8641 1 /* MPC8641 specific */ -#define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */ -#define CONFIG_MP 1 /* support multiple processors */ -#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ -/*#define CONFIG_PHYS_64BIT 1*/ /* Place devices in 36-bit space */ -#define CONFIG_ADDR_MAP 1 /* Use addr map */ - -/* - * default CCSRBAR is at 0xff700000 - * assume U-Boot is less than 0.5MB - */ -#define CONFIG_SYS_TEXT_BASE 0xeff00000 - -#ifdef RUN_DIAG -#define CONFIG_SYS_DIAG_ADDR CONFIG_SYS_FLASH_BASE -#endif - -/* - * virtual address to be used for temporary mappings. There - * should be 128k free at this VA. - */ -#define CONFIG_SYS_SCRATCH_VA 0xe0000000 - -#define CONFIG_SYS_SRIO -#define CONFIG_SRIO1 /* SRIO port 1 */ - -#define CONFIG_PCI 1 /* Enable PCI/PCIE */ -#define CONFIG_PCIE1 1 /* PCIE controler 1 (ULI bridge) */ -#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot) */ -#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ -#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ -#define CONFIG_FSL_LAW 1 /* Use common FSL law init code */ - -#define CONFIG_TSEC_ENET /* tsec ethernet support */ -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_BAT_RW 1 /* Use common BAT rw code */ -#define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */ -#define CONFIG_SYS_NUM_ADDR_MAP 8 /* Number of addr map slots = 8 dbats */ - -#define CONFIG_ALTIVEC 1 - -/* - * L2CR setup -- make sure this is right for your board! - */ -#define CONFIG_SYS_L2 -#define L2_INIT 0 -#define L2_ENABLE (L2CR_L2E) - -#ifndef CONFIG_SYS_CLK_FREQ -#ifndef __ASSEMBLY__ -extern unsigned long get_board_sys_clk(unsigned long dummy); -#endif -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) -#endif - -#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x00400000 - -/* - * With the exception of PCI Memory and Rapid IO, most devices will simply - * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA - * when 36-bit is enabled. When 36-bit is not enabled, these bits are 0. - */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PHYS_ADDR_HIGH 0x0000000f -#else -#define CONFIG_SYS_PHYS_ADDR_HIGH 0x00000000 -#endif - -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ - -/* Physical addresses */ -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR -#define CONFIG_SYS_CCSRBAR_PHYS_HIGH CONFIG_SYS_PHYS_ADDR_HIGH -#define CONFIG_SYS_CCSRBAR_PHYS \ - PAIRED_PHYS_TO_PHYS(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ - CONFIG_SYS_CCSRBAR_PHYS_HIGH) - -#define CONFIG_HWCONFIG /* use hwconfig to control memory interleaving */ - -/* - * DDR Setup - */ -#define CONFIG_SYS_FSL_DDR2 -#undef CONFIG_FSL_DDR_INTERACTIVE -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -#define CONFIG_DDR_SPD - -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE -#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ -#define CONFIG_VERY_BIG_RAM - -#define CONFIG_NUM_DDR_CONTROLLERS 2 -#define CONFIG_DIMM_SLOTS_PER_CTLR 2 -#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) - -/* - * I2C addresses of SPD EEPROMs - */ -#define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ -#define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 0 DIMM 1 */ -#define SPD_EEPROM_ADDRESS3 0x53 /* CTLR 1 DIMM 0 */ -#define SPD_EEPROM_ADDRESS4 0x54 /* CTLR 1 DIMM 1 */ - - -/* - * These are used when DDR doesn't use SPD. - */ -#define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */ -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F -#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */ -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 -#define CONFIG_SYS_DDR_TIMING_0 0x00260802 -#define CONFIG_SYS_DDR_TIMING_1 0x39357322 -#define CONFIG_SYS_DDR_TIMING_2 0x14904cc8 -#define CONFIG_SYS_DDR_MODE_1 0x00480432 -#define CONFIG_SYS_DDR_MODE_2 0x00000000 -#define CONFIG_SYS_DDR_INTERVAL 0x06090100 -#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef -#define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 -#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 -#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 -#define CONFIG_SYS_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ -#define CONFIG_SYS_DDR_CONTROL2 0x04400000 - -#define CONFIG_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_NXID -#define CONFIG_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -#define CONFIG_SYS_FLASH_BASE 0xef800000 /* start of FLASH 8M */ -#define CONFIG_SYS_FLASH_BASE_PHYS_LOW CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_FLASH_BASE_PHYS \ - PAIRED_PHYS_TO_PHYS(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ - CONFIG_SYS_PHYS_ADDR_HIGH) - -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} - -#define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ - | 0x00001001) /* port size 16bit */ -#define CONFIG_SYS_OR0_PRELIM 0xff806ff7 /* 8MB Boot Flash area*/ - -#define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CF_BASE_PHYS) \ - | 0x00001001) /* port size 16bit */ -#define CONFIG_SYS_OR2_PRELIM 0xffffeff7 /* 32k Compact Flash */ - -#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) \ - | 0x00000801) /* port size 8bit */ -#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32k PIXIS area*/ - -/* - * The LBC_BASE is the base of the region that contains the PIXIS and the CF. - * The PIXIS and CF by themselves aren't large enough to take up the 128k - * required for the smallest BAT mapping, so there's a 64k hole. - */ -#define CONFIG_SYS_LBC_BASE 0xffde0000 -#define CONFIG_SYS_LBC_BASE_PHYS_LOW CONFIG_SYS_LBC_BASE - -#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ -#define PIXIS_BASE (CONFIG_SYS_LBC_BASE + 0x00010000) -#define PIXIS_BASE_PHYS_LOW (CONFIG_SYS_LBC_BASE_PHYS_LOW + 0x00010000) -#define PIXIS_BASE_PHYS PAIRED_PHYS_TO_PHYS(PIXIS_BASE_PHYS_LOW, \ - CONFIG_SYS_PHYS_ADDR_HIGH) -#define PIXIS_SIZE 0x00008000 /* 32k */ -#define PIXIS_ID 0x0 /* Board ID at offset 0 */ -#define PIXIS_VER 0x1 /* Board version at offset 1 */ -#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ -#define PIXIS_RST 0x4 /* PIXIS Reset Control register */ -#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */ -#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ -#define PIXIS_VCTL 0x10 /* VELA Control Register */ -#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ -#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ -#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ -#define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */ -#define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */ -#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ -#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ -#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ -#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ -#define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ - -/* Compact flash shares a BAT with PIXIS; make sure they're contiguous */ -#define CF_BASE (PIXIS_BASE + PIXIS_SIZE) -#define CF_BASE_PHYS (PIXIS_BASE_PHYS + PIXIS_SIZE) - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ - -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_EMPTY_INFO - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -#if defined(CONFIG_SYS_RAMBOOT) -#undef CONFIG_SPD_EEPROM -#define CONFIG_SYS_SDRAM_SIZE 256 -#endif - -#undef CONFIG_CLOCKS_IN_MHZ - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#ifndef CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */ -#else -#define CONFIG_SYS_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ -#endif -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ - -/* Serial Port */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) - -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER - -/* - * Pass open firmware flat tree to kernel - */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS 1 - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } - -/* - * RapidIO MMU - */ -#define CONFIG_SYS_SRIO1_MEM_BASE 0x80000000 /* base address */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_SRIO1_MEM_PHYS_LOW 0x00000000 -#define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH 0x0000000c -#else -#define CONFIG_SYS_SRIO1_MEM_PHYS_LOW CONFIG_SYS_SRIO1_MEM_BASE -#define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH 0x00000000 -#endif -#define CONFIG_SYS_SRIO1_MEM_PHYS \ - PAIRED_PHYS_TO_PHYS(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ - CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) -#define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 128M */ - -/* - * General PCI - * Addresses are mapped 1-1. - */ - -#define CONFIG_SYS_PCIE1_NAME "ULI" -#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS_LOW 0x00000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 0x0000000c -#else -#define CONFIG_SYS_PCIE1_MEM_BUS CONFIG_SYS_PCIE1_MEM_VIRT -#define CONFIG_SYS_PCIE1_MEM_PHYS_LOW CONFIG_SYS_PCIE1_MEM_VIRT -#define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 0x00000000 -#endif -#define CONFIG_SYS_PCIE1_MEM_PHYS \ - PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ - CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 -#define CONFIG_SYS_PCIE1_IO_PHYS_LOW CONFIG_SYS_PCIE1_IO_VIRT -#define CONFIG_SYS_PCIE1_IO_PHYS \ - PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ - CONFIG_SYS_PHYS_ADDR_HIGH) -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64K */ - -#ifdef CONFIG_PHYS_64BIT -/* - * Use the same PCI bus address on PCIE1 and PCIE2 if we have PHYS_64BIT. - * This will increase the amount of PCI address space available for - * for mapping RAM. - */ -#define CONFIG_SYS_PCIE2_MEM_BUS CONFIG_SYS_PCIE1_MEM_BUS -#else -#define CONFIG_SYS_PCIE2_MEM_BUS (CONFIG_SYS_PCIE1_MEM_BUS \ - + CONFIG_SYS_PCIE1_MEM_SIZE) -#endif -#define CONFIG_SYS_PCIE2_MEM_VIRT (CONFIG_SYS_PCIE1_MEM_VIRT \ - + CONFIG_SYS_PCIE1_MEM_SIZE) -#define CONFIG_SYS_PCIE2_MEM_PHYS_LOW (CONFIG_SYS_PCIE1_MEM_PHYS_LOW \ - + CONFIG_SYS_PCIE1_MEM_SIZE) -#define CONFIG_SYS_PCIE2_MEM_PHYS_HIGH CONFIG_SYS_PCIE1_MEM_PHYS_HIGH -#define CONFIG_SYS_PCIE2_MEM_PHYS (CONFIG_SYS_PCIE1_MEM_PHYS \ - + CONFIG_SYS_PCIE1_MEM_SIZE) -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE2_IO_VIRT (CONFIG_SYS_PCIE1_IO_VIRT \ - + CONFIG_SYS_PCIE1_IO_SIZE) -#define CONFIG_SYS_PCIE2_IO_PHYS_LOW (CONFIG_SYS_PCIE1_IO_PHYS_LOW \ - + CONFIG_SYS_PCIE1_IO_SIZE) -#define CONFIG_SYS_PCIE2_IO_PHYS (CONFIG_SYS_PCIE1_IO_PHYS \ - + CONFIG_SYS_PCIE1_IO_SIZE) -#define CONFIG_SYS_PCIE2_IO_SIZE CONFIG_SYS_PCIE1_IO_SIZE - -#if defined(CONFIG_PCI) - -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ - -#undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE - -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - -#define CONFIG_RTL8139 - -#undef CONFIG_EEPRO100 -#undef CONFIG_TULIP - -/************************************************************ - * USB support - ************************************************************/ -#define CONFIG_PCI_OHCI 1 -#define CONFIG_USB_OHCI_NEW 1 -#define CONFIG_USB_KEYBOARD 1 -#define CONFIG_SYS_STDIO_DEREGISTER -#define CONFIG_SYS_USB_EVENT_POLL 1 -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 -#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 - -/*PCIE video card used*/ -#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT - -/*PCI video card used*/ -/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT*/ - -/* video */ -#define CONFIG_VIDEO - -#if defined(CONFIG_VIDEO) -#define CONFIG_BIOSEMU -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_ATI_RADEON_FB -#define CONFIG_VIDEO_LOGO -/*#define CONFIG_CONSOLE_CURSOR*/ -#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT -#endif - -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ - -#define CONFIG_DOS_PARTITION -#define CONFIG_SCSI_AHCI - -#ifdef CONFIG_SCSI_AHCI -#define CONFIG_LIBATA -#define CONFIG_SATA_ULI5288 -#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 -#define CONFIG_SYS_SCSI_MAX_LUN 1 -#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) -#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE -#endif - -#endif /* CONFIG_PCI */ - -#if defined(CONFIG_TSEC_ENET) - -#define CONFIG_MII 1 /* MII PHY management */ - -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "eTSEC1" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "eTSEC2" -#define CONFIG_TSEC3 1 -#define CONFIG_TSEC3_NAME "eTSEC3" -#define CONFIG_TSEC4 1 -#define CONFIG_TSEC4_NAME "eTSEC4" - -#define TSEC1_PHY_ADDR 0 -#define TSEC2_PHY_ADDR 1 -#define TSEC3_PHY_ADDR 2 -#define TSEC4_PHY_ADDR 3 -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC3_PHYIDX 0 -#define TSEC4_PHYIDX 0 -#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) - -#define CONFIG_ETHPRIME "eTSEC1" - -#endif /* CONFIG_TSEC_ENET */ - - -#ifdef CONFIG_PHYS_64BIT -#define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8) -#define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2) - -/* Put physical address into the BAT format */ -#define BAT_PHYS_ADDR(low, high) \ - (low | PHYS_HIGH_TO_BXPN(high) | PHYS_HIGH_TO_BX(high)) -/* Convert high/low pairs to actual 64-bit value */ -#define PAIRED_PHYS_TO_PHYS(low, high) (low | ((u64)high << 32)) -#else -/* 32-bit systems just ignore the "high" bits */ -#define BAT_PHYS_ADDR(low, high) (low) -#define PAIRED_PHYS_TO_PHYS(low, high) (low) -#endif - -/* - * BAT0 DDR - */ -#define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) - -/* - * BAT1 LBC (PIXIS/CF) - */ -#define CONFIG_SYS_DBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \ - CONFIG_SYS_PHYS_ADDR_HIGH) \ - | BATL_PP_RW | BATL_CACHEINHIBIT | \ - BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT1U (CONFIG_SYS_LBC_BASE | BATU_BL_128K \ - | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \ - CONFIG_SYS_PHYS_ADDR_HIGH) \ - | BATL_PP_RW | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U - -/* if CONFIG_PCI: - * BAT2 PCIE1 and PCIE1 MEM - * if CONFIG_RIO - * BAT2 Rapidio Memory - */ -#ifdef CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE -#define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ - CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \ - | BATL_PP_RW | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_1G \ - | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ - CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \ - | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U -#else /* CONFIG_RIO */ -#define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ - CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \ - | BATL_PP_RW | BATL_CACHEINHIBIT | \ - BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT2U (CONFIG_SYS_SRIO1_MEM_BASE | BATU_BL_512M \ - | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ - CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \ - | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U -#endif - -/* - * BAT3 CCSR Space - */ -#define CONFIG_SYS_DBAT3L (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ - CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ - | BATL_PP_RW | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_IBAT3L (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ - CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ - | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U - -#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) -#define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ - | BATL_PP_RW | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \ - | BATU_BL_1M | BATU_VS | BATU_VP) -#define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ - | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU -#endif - -/* - * BAT4 PCIE1_IO and PCIE2_IO - */ -#define CONFIG_SYS_DBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ - CONFIG_SYS_PHYS_ADDR_HIGH) \ - | BATL_PP_RW | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_128K \ - | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ - CONFIG_SYS_PHYS_ADDR_HIGH) \ - | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U - -/* - * BAT5 Init RAM for stack in the CPU DCache (no backing memory) - */ -#define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) -#define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L -#define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U - -/* - * BAT6 FLASH - */ -#define CONFIG_SYS_DBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ - CONFIG_SYS_PHYS_ADDR_HIGH) \ - | BATL_PP_RW | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_IBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ - CONFIG_SYS_PHYS_ADDR_HIGH) \ - | BATL_PP_RW | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U - -/* Map the last 1M of flash where we're running from reset */ -#define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ - | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY - -/* - * BAT7 FREE - used later for tmp mappings - */ -#define CONFIG_SYS_DBAT7L 0x00000000 -#define CONFIG_SYS_DBAT7U 0x00000000 -#define CONFIG_SYS_IBAT7L 0x00000000 -#define CONFIG_SYS_IBAT7U 0x00000000 - -/* - * Environment - */ -#ifndef CONFIG_SYS_RAMBOOT - #define CONFIG_ENV_IS_IN_FLASH 1 - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x60000) - #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ -#else - #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#endif -#define CONFIG_ENV_SIZE 0x2000 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PING -#define CONFIG_CMD_I2C -#define CONFIG_CMD_REGINFO - -#if defined(CONFIG_SYS_RAMBOOT) - #undef CONFIG_CMD_SAVEENV -#endif - -#if defined(CONFIG_PCI) - #define CONFIG_CMD_PCI - #define CONFIG_CMD_SCSI - #define CONFIG_CMD_EXT2 - #define CONFIG_CMD_USB -#endif - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -#if defined(CONFIG_CMD_KGDB) - #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else - #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ - -#if defined(CONFIG_CMD_KGDB) - #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Environment Configuration - */ - -/* The mac addresses for all ethernet interface */ -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_ETHADDR 00:E0:0C:00:00:01 -#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD -#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD -#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD -#endif - -#define CONFIG_HAS_ETH0 1 -#define CONFIG_HAS_ETH1 1 -#define CONFIG_HAS_ETH2 1 -#define CONFIG_HAS_ETH3 1 - -#define CONFIG_IPADDR 192.168.1.100 - -#define CONFIG_HOSTNAME unknown -#define CONFIG_ROOTPATH "/opt/nfsroot" -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ - -#define CONFIG_SERVERIP 192.168.1.1 -#define CONFIG_GATEWAYIP 192.168.1.1 -#define CONFIG_NETMASK 255.255.255.0 - -/* default location for tftp and bootm */ -#define CONFIG_LOADADDR 1000000 - -#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ -#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ - "tftpflash=tftpboot $loadaddr $uboot; " \ - "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize; " \ - "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=2000000\0" \ - "ramdiskfile=your.ramdisk.u-boot\0" \ - "fdtaddr=c00000\0" \ - "fdtfile=mpc8641_hpcn.dtb\0" \ - "en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0" \ - "dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \ - "maxcpus=2" - - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND - -#endif /* __CONFIG_H */ |