diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/M5282EVB.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/M5282EVB.h | 236 |
1 files changed, 0 insertions, 236 deletions
diff --git a/qemu/roms/u-boot/include/configs/M5282EVB.h b/qemu/roms/u-boot/include/configs/M5282EVB.h deleted file mode 100644 index fd970d078..000000000 --- a/qemu/roms/u-boot/include/configs/M5282EVB.h +++ /dev/null @@ -1,236 +0,0 @@ -/* - * Configuation settings for the Motorola MC5282EVB board. - * - * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef _CONFIG_M5282EVB_H -#define _CONFIG_M5282EVB_H - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_MCF52x2 /* define processor family */ -#define CONFIG_M5282 /* define processor type */ - -#define CONFIG_MCFTMR - -#define CONFIG_MCFUART -#define CONFIG_SYS_UART_PORT (0) -#define CONFIG_BAUDRATE 115200 - -#undef CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */ - -/* Configuration for environment - * Environment is embedded in u-boot in the second sector of the flash - */ -#define CONFIG_ENV_ADDR 0xffe04000 -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_IS_IN_FLASH 1 - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_NET -#define CONFIG_CMD_PING -#define CONFIG_CMD_MII - -#undef CONFIG_CMD_LOADS -#undef CONFIG_CMD_LOADB - -#define CONFIG_MCFFEC -#ifdef CONFIG_MCFFEC -# define CONFIG_MII 1 -# define CONFIG_MII_INIT 1 -# define CONFIG_SYS_DISCOVER_PHY -# define CONFIG_SYS_RX_ETH_BUFFER 8 -# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN - -# define CONFIG_SYS_FEC0_PINMUX 0 -# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE -# define MCFFEC_TOUT_LOOP 50000 -/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ -# ifndef CONFIG_SYS_DISCOVER_PHY -# define FECDUPLEX FULL -# define FECSPEED _100BASET -# else -# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN -# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN -# endif -# endif /* CONFIG_SYS_DISCOVER_PHY */ -#endif - -#define CONFIG_BOOTDELAY 5 -#ifdef CONFIG_MCFFEC -# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60 -# define CONFIG_IPADDR 192.162.1.2 -# define CONFIG_NETMASK 255.255.255.0 -# define CONFIG_SERVERIP 192.162.1.1 -# define CONFIG_GATEWAYIP 192.162.1.1 -# define CONFIG_OVERWRITE_ETHADDR_ONCE -#endif /* CONFIG_MCFFEC */ - -#define CONFIG_HOSTNAME M5282EVB -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "loadaddr=10000\0" \ - "u-boot=u-boot.bin\0" \ - "load=tftp ${loadaddr) ${u-boot}\0" \ - "upd=run load; run prog\0" \ - "prog=prot off ffe00000 ffe3ffff;" \ - "era ffe00000 ffe3ffff;" \ - "cp.b ${loadaddr} ffe00000 ${filesize};"\ - "save\0" \ - "" - -#define CONFIG_SYS_PROMPT "-> " -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_LOAD_ADDR 0x20000 - -#define CONFIG_SYS_MEMTEST_START 0x400 -#define CONFIG_SYS_MEMTEST_END 0x380000 - -#define CONFIG_SYS_CLK 64000000 - -/* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */ - -#define CONFIG_SYS_MFD 0x02 /* PLL Multiplication Factor Devider */ -#define CONFIG_SYS_RFD 0x00 /* PLL Reduce Frecuency Devider */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -#define CONFIG_SYS_MBAR 0x40000000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE -#define CONFIG_SYS_INT_FLASH_BASE 0xf0000000 -#define CONFIG_SYS_INT_FLASH_ENABLE 0x21 - -/* If M5282 port is fully implemented the monitor base will be behind - * the vector table. */ -#if (CONFIG_SYS_TEXT_BASE != CONFIG_SYS_INT_FLASH_BASE) -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) -#else -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x418) /* 24 Byte for CFM-Config */ -#endif - -#define CONFIG_SYS_MONITOR_LEN 0x20000 -#define CONFIG_SYS_MALLOC_LEN (256 << 10) -#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization ?? - */ -#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_FLASH_CFI -#ifdef CONFIG_SYS_FLASH_CFI - -# define CONFIG_FLASH_CFI_DRIVER 1 -# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */ -# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT -# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ -# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ -# define CONFIG_SYS_FLASH_CHECKSUM -# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } -#endif - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 - -#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 8) -#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 4) -#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV + CF_CACR_DCM) -#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ - CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ - CF_ACR_EN | CF_ACR_SM_ALL) -#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_DISD | \ - CF_CACR_CEIB | CF_CACR_DBWE | \ - CF_CACR_EUSP) - -/*----------------------------------------------------------------------- - * Memory bank definitions - */ -#define CONFIG_SYS_CS0_BASE 0xFFE00000 -#define CONFIG_SYS_CS0_CTRL 0x00001980 -#define CONFIG_SYS_CS0_MASK 0x001F0001 - -/*----------------------------------------------------------------------- - * Port configuration - */ -#define CONFIG_SYS_PACNT 0x0000000 /* Port A D[31:24] */ -#define CONFIG_SYS_PADDR 0x0000000 -#define CONFIG_SYS_PADAT 0x0000000 - -#define CONFIG_SYS_PBCNT 0x0000000 /* Port B D[23:16] */ -#define CONFIG_SYS_PBDDR 0x0000000 -#define CONFIG_SYS_PBDAT 0x0000000 - -#define CONFIG_SYS_PCCNT 0x0000000 /* Port C D[15:08] */ -#define CONFIG_SYS_PCDDR 0x0000000 -#define CONFIG_SYS_PCDAT 0x0000000 - -#define CONFIG_SYS_PDCNT 0x0000000 /* Port D D[07:00] */ -#define CONFIG_SYS_PCDDR 0x0000000 -#define CONFIG_SYS_PCDAT 0x0000000 - -#define CONFIG_SYS_PEHLPAR 0xC0 -#define CONFIG_SYS_PUAPAR 0x0F /* UA0..UA3 = Uart 0 +1 */ -#define CONFIG_SYS_DDRUA 0x05 -#define CONFIG_SYS_PJPAR 0xFF - -#endif /* _CONFIG_M5282EVB_H */ |