diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/JSE.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/JSE.h | 276 |
1 files changed, 0 insertions, 276 deletions
diff --git a/qemu/roms/u-boot/include/configs/JSE.h b/qemu/roms/u-boot/include/configs/JSE.h deleted file mode 100644 index 5cc25576a..000000000 --- a/qemu/roms/u-boot/include/configs/JSE.h +++ /dev/null @@ -1,276 +0,0 @@ -/* - * (C) Copyright 2003 Picture Elements, Inc. - * Stephen Williams <steve@icarus.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options for the JSE board - * (Theoretically easy to change, but the board is fixed.) - */ - -#define CONFIG_JSE 1 - /* JSE has a PPC405GPr */ -#define CONFIG_405GP 1 - /* ... with a 33MHz OSC. connected to the SysCLK input */ -#define CONFIG_SYS_CLK_FREQ 33333333 - /* ... with on-chip memory here (4KBytes) */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF4000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x00001000 - /* Do not set up locked dcache as init ram. */ -#undef CONFIG_SYS_INIT_DCACHE_CS - -#define CONFIG_SYS_TEXT_BASE 0xFFF80000 - - /* Map the SystemACE chip (CS#1) here. (Must be a multiple of 1Meg) */ -#define CONFIG_SYSTEMACE 1 -#define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000 -#define CONFIG_SYS_SYSTEMACE_WIDTH 8 -#define CONFIG_DOS_PARTITION 1 - - /* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 - /* ... place INIT RAM in the OCM address */ -# define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR - /* ... give it the whole init ram */ -# define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE - /* ... Shave a bit off the end for global data */ -# define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - /* ... and place the stack pointer at the top of what's left. */ -# define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - - /* Enable board_pre_init function */ -#define CONFIG_BOARD_PRE_INIT 1 -#define CONFIG_BOARD_EARLY_INIT_F 1 - /* Disable post-clk setup init function */ -#undef CONFIG_BOARD_POSTCLK_INIT - /* Disable call to post_init_f: late init function. */ -#undef CONFIG_POST - /* Enable DRAM test. */ -#define CONFIG_SYS_DRAM_TEST 1 - /* Enable misc_init_r function. */ -#define CONFIG_MISC_INIT_R 1 - - /* JSE has EEPROM chips that are good for environment. */ -#undef CONFIG_ENV_IS_IN_NVRAM -#undef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_IS_IN_EEPROM 1 -#undef CONFIG_ENV_IS_NOWHERE - - /* This is the 7bit address of the device, not including P. */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 - /* After the device address, need one more address byte. */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - /* The EEPROM is 512 bytes. */ -#define CONFIG_SYS_EEPROM_SIZE 512 - /* The EEPROM can do 16byte ( 1 << 4 ) page writes. */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - /* Put the environment in the second half. */ -#define CONFIG_ENV_OFFSET 0x00 -#define CONFIG_ENV_SIZE 512 - - /* The JSE connects UART1 to the console tap connector. */ -#define CONFIG_CONS_INDEX 2 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - - /* Set console baudrate to 9600 */ -#define CONFIG_BAUDRATE 9600 - -/* - * Configuration related to auto-boot. - * - * CONFIG_BOOTDELAY sets the delay (in seconds) that U-Boot will wait - * before resorting to autoboot. This value can be overridden by the - * bootdelay environment variable. - * - * CONFIG_AUTOBOOT_PROMPT is the string that U-Boot emits to warn the - * user that an autoboot will happen. - * - * CONFIG_BOOTCOMMAND is the sequence of commands that U-Boot will - * execute to boot the JSE. This loads the uimage and initrd.img files - * from CompactFlash into memory, then boots them from memory. - * - * CONFIG_BOOTARGS is the arguments passed to the Linux kernel to get - * it going on the JSE. - */ -#define CONFIG_BOOTDELAY 5 -#define CONFIG_BOOTARGS "root=/dev/ram0 init=/linuxrc rw" -#define CONFIG_BOOTCOMMAND "fatload ace 0 2000000 uimage; fatload ace 0 2100000 initrd.img; bootm 2000000 2100000" - - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 1 /* PHY address */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_FLASH -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING - - - /* watchdog disabled */ -#undef CONFIG_WATCHDOG - /* SPD EEPROM (sdram speed config) disabled */ -#undef CONFIG_SPD_EEPROM -#undef SPD_EEPROM_ADDRESS - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* - * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1. - * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31. - * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value. - * The Linux BASE_BAUD define should match this configuration. - * baseBaud = cpuClock/(uartDivisor*16) - * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, - * set Linux BASE_BAUD to 403200. - */ -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ -#define CONFIG_SYS_BASE_BAUD 691200 - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#undef CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ - -/*----------------------------------------------------------------------- - * External peripheral base address - *----------------------------------------------------------------------- - */ -#undef CONFIG_IDE_LED /* no led for ide supported */ -#undef CONFIG_IDE_RESET /* no reset for ide supported */ - -#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000 -#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000 -#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000 - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFF80000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ - - -/* Configuration Port location */ -#define CONFIG_PORT_ADDR 0xF0000500 - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif -#endif /* __CONFIG_H */ |