diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/ESTEEM192E.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/ESTEEM192E.h | 292 |
1 files changed, 292 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/ESTEEM192E.h b/qemu/roms/u-boot/include/configs/ESTEEM192E.h new file mode 100644 index 000000000..347f8b64a --- /dev/null +++ b/qemu/roms/u-boot/include/configs/ESTEEM192E.h @@ -0,0 +1,292 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC850 1 /* This is a MPC850 CPU */ +#define CONFIG_ESTEEM192E 1 /* ...on a EST ESTEEM192E */ + +#define CONFIG_SYS_TEXT_BASE 0x40000000 + +#define CONFIG_FLASH_16BIT 1 /* Rom 16 bit data bus */ + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE + +#define MPC8XX_FACT 10 /* Multiply by 10 */ +#define MPC8XX_XIN 4915200 /* 4.915200 MHz in - ??? - XXX */ +#define CONFIG_SYS_PLPRCR_MF ((MPC8XX_FACT-1) << 20) +#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) /* 49,152,000 Hz */ + +#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ /* Force it - dont measure it */ + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_BAUDRATE 9600 +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif +#define CONFIG_BOOTCOMMAND "bootm 40030000" /* autoboot command */ + +#define CONFIG_BOOTARGS "root=/dev/ram rw ramdisk=8192 " \ + "ip=100.100.100.21:100.100.100.14:100.100.100.1:255.0.0.0 " +/* + * Miscellaneous configurable options + */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_BOOTFILESIZE + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + + +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "BOOT: " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 8 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CONFIG_SYS_IMMR 0xFF000000 + + /*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0x40000000 +#ifdef DEBUG +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ +#endif +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ +#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) + +/*----------------------------------------------------------------------- + * SUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) /* DBGC00 */ + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE) + +/* (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) */ + + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit - leave PLL multiplication factor unchanged ! + */ +#define CONFIG_SYS_PLPRCR (CONFIG_SYS_PLPRCR_MF | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +#define CONFIG_SYS_SCCR (SCCR_TBS | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00) + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000) +#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000) +#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000) +#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) + +#define CONFIG_SYS_PCMCIA_INTERRUPT SIU_LEVEL6 + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +/*#define CONFIG_SYS_DER 0x2002000F*/ +#define CONFIG_SYS_DER 0 +/*#define CONFIG_SYS_DER 0x02002000 */ + + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ + +/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ +#define CONFIG_SYS_OR_TIMING_FLASH 0x00000160 + /*(OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \ + OR_SCY_5_CLK | OR_EHTR) */ + +#define CONFIG_SYS_OR0_REMAP 0x80000160 /*(CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)*/ +#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) +#define CONFIG_SYS_BR0_PRELIM ( FLASH_BASE0_PRELIM | 0x00000801 ) + +#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM +#define CONFIG_SYS_BR1_PRELIM ( FLASH_BASE1_PRELIM | 0x00000801 ) + +/* + * BR2/3 and OR2/3 (SDRAM) + * + */ +#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */ +#define SDRAM_BASE3_PRELIM 0x04000000 /* SDRAM bank #1 */ +#define SDRAM_MAX_SIZE 0x02000000 /* max 32 MB per bank */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ +#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00 + +#define CONFIG_SYS_OR2_PRELIM 0xFC000E00 +#define CONFIG_SYS_BR2_PRELIM (SDRAM_BASE2_PRELIM | 0x00000081) + +#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM +#define CONFIG_SYS_BR3_PRELIM (SDRAM_BASE3_PRELIM | 0x00000081) + + +/* + * Memory Periodic Timer Prescaler + */ + +/* periodic timer for refresh */ +#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */ + +/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ +#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ + +/* + * MAMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CONFIG_SYS_MAMR_8COL 0x18803112 +#define CONFIG_SYS_MAMR_9COL 0x18803112 /* same as 8 column because its just easier to port with*/ + +#endif /* __CONFIG_H */ |