diff options
Diffstat (limited to 'qemu/roms/u-boot/board/xes/xpedite517x/ddr.c')
| -rw-r--r-- | qemu/roms/u-boot/board/xes/xpedite517x/ddr.c | 124 |
1 files changed, 0 insertions, 124 deletions
diff --git a/qemu/roms/u-boot/board/xes/xpedite517x/ddr.c b/qemu/roms/u-boot/board/xes/xpedite517x/ddr.c deleted file mode 100644 index fd602ea7e..000000000 --- a/qemu/roms/u-boot/board/xes/xpedite517x/ddr.c +++ /dev/null @@ -1,124 +0,0 @@ -/* - * Copyright 2009 Extreme Engineering Solutions, Inc. - * Copyright 2007-2008 Freescale Semiconductor, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <i2c.h> -#include <fsl_ddr_sdram.h> -#include <fsl_ddr_dimm_params.h> - -void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address) -{ - i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd, - sizeof(ddr2_spd_eeprom_t)); -} - -/* - * There are four board-specific SDRAM timing parameters which must be - * calculated based on the particular PCB artwork. These are: - * 1.) CPO (Read Capture Delay) - * - TIMING_CFG_2 register - * Source: Calculation based on board trace lengths and - * chip-specific internal delays. - * 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay) - * - TIMING_CFG_2 register - * Source: Calculation based on board trace lengths. - * Unless clock and DQ lanes are very different - * lengths (>2"), this should be set to the nominal value - * of 1/2 clock delay. - * 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control) - * - DDR_SDRAM_CLK_CNTL register - * Source: Signal Integrity Simulations - * 4.) 2T Timing on Addr/Ctl - * - TIMING_CFG_2 register - * Source: Signal Integrity Simulations - * Usually only needed with heavy load/very high speed (>DDR2-800) - * - * PCB routing on the XPedite5170 is nearly identical to the XPedite5370 - * so we use the XPedite5370 settings as a basis for the XPedite5170. - */ - -typedef struct board_memctl_options { - uint16_t datarate_mhz_low; - uint16_t datarate_mhz_high; - uint8_t clk_adjust; - uint8_t cpo_override; - uint8_t write_data_delay; -} board_memctl_options_t; - -static struct board_memctl_options bopts_ctrl[][2] = { - { - /* Controller 0 */ - { - /* DDR2 600/667 */ - .datarate_mhz_low = 500, - .datarate_mhz_high = 750, - .clk_adjust = 5, - .cpo_override = 8, - .write_data_delay = 2, - }, - { - /* DDR2 800 */ - .datarate_mhz_low = 750, - .datarate_mhz_high = 850, - .clk_adjust = 5, - .cpo_override = 9, - .write_data_delay = 2, - }, - }, - { - /* Controller 1 */ - { - /* DDR2 600/667 */ - .datarate_mhz_low = 500, - .datarate_mhz_high = 750, - .clk_adjust = 5, - .cpo_override = 7, - .write_data_delay = 2, - }, - { - /* DDR2 800 */ - .datarate_mhz_low = 750, - .datarate_mhz_high = 850, - .clk_adjust = 5, - .cpo_override = 8, - .write_data_delay = 2, - }, - }, -}; - -void fsl_ddr_board_options(memctl_options_t *popts, - dimm_params_t *pdimm, - unsigned int ctrl_num) -{ - struct board_memctl_options *bopts = bopts_ctrl[ctrl_num]; - sys_info_t sysinfo; - int i; - unsigned int datarate; - - get_sys_info(&sysinfo); - datarate = get_ddr_freq(0) / 1000000; - - for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) { - if ((bopts[i].datarate_mhz_low <= datarate) && - (bopts[i].datarate_mhz_high >= datarate)) { - debug("controller %d:\n", ctrl_num); - debug(" clk_adjust = %d\n", bopts[i].clk_adjust); - debug(" cpo = %d\n", bopts[i].cpo_override); - debug(" write_data_delay = %d\n", - bopts[i].write_data_delay); - popts->clk_adjust = bopts[i].clk_adjust; - popts->cpo_override = bopts[i].cpo_override; - popts->write_data_delay = bopts[i].write_data_delay; - } - } - - /* - * Factors to consider for half-strength driver enable: - * - number of DIMMs installed - */ - popts->half_strength_driver_enable = 0; -} |