1 files changed, 0 insertions, 116 deletions

diff --git a/qemu/roms/u-boot/board/freescale/t1040qds/ddr.c b/qemu/roms/u-boot/board/freescale/t1040qds/ddr.c
deleted file mode 100644
index 43f952f9c..000000000
--- a/qemu/roms/u-boot/board/freescale/t1040qds/ddr.c
+++ /dev/null
@@ -1,116 +0,0 @@
-/*
- * Copyright 2013-2014 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <hwconfig.h>
-#include <asm/mmu.h>
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-#include <asm/fsl_law.h>
-#include "ddr.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void fsl_ddr_board_options(memctl_options_t *popts,
-				dimm_params_t *pdimm,
-				unsigned int ctrl_num)
-{
-	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
-	ulong ddr_freq;
-
-	if (ctrl_num > 2) {
-		printf("Not supported controller number %d\n", ctrl_num);
-		return;
-	}
-	if (!pdimm->n_ranks)
-		return;
-
-	pbsp = udimms[0];
-
-	/* Get clk_adjust, cpo, write_data_delay,2t, according to the board ddr
-	 * freqency and n_banks specified in board_specific_parameters table.
-	 */
-	ddr_freq = get_ddr_freq(0) / 1000000;
-	while (pbsp->datarate_mhz_high) {
-		if (pbsp->n_ranks == pdimm->n_ranks &&
-		    (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
-			if (ddr_freq <= pbsp->datarate_mhz_high) {
-				popts->clk_adjust = pbsp->clk_adjust;
-				popts->wrlvl_start = pbsp->wrlvl_start;
-				popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
-				popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
-				goto found;
-			}
-			pbsp_highest = pbsp;
-		}
-		pbsp++;
-	}
-
-	if (pbsp_highest) {
-		printf("Error: board specific timing not found\n");
-		printf("for data rate %lu MT/s\n", ddr_freq);
-		printf("Trying to use the highest speed (%u) parameters\n",
-		       pbsp_highest->datarate_mhz_high);
-		popts->clk_adjust = pbsp_highest->clk_adjust;
-		popts->wrlvl_start = pbsp_highest->wrlvl_start;
-		popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
-		popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
-	} else {
-		panic("DIMM is not supported by this board");
-	}
-found:
-	debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
-		"\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, "
-		"wrlvl_ctrl_3 0x%x\n",
-		pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
-		pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
-		pbsp->wrlvl_ctl_3);
-
-	/*
-	 * Factors to consider for half-strength driver enable:
-	 *	- number of DIMMs installed
-	 */
-	popts->half_strength_driver_enable = 1;
-	/*
-	 * Write leveling override
-	 */
-	popts->wrlvl_override = 1;
-	popts->wrlvl_sample = 0xf;
-
-	/*
-	 * rtt and rtt_wr override
-	 */
-	popts->rtt_override = 0;
-
-	/* Enable ZQ calibration */
-	popts->zq_en = 1;
-
-	/* DHC_EN =1, ODT = 75 Ohm */
-#ifdef CONFIG_SYS_FSL_DDR4
-	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
-	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
-			  DDR_CDR2_VREF_OVRD(70);	/* Vref = 70% */
-#else
-	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
-	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
-#endif
-}
-
-phys_size_t initdram(int board_type)
-{
-	phys_size_t dram_size;
-
-	puts("Initializing....using SPD\n");
-
-	dram_size = fsl_ddr_sdram();
-
-	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
-	dram_size *= 0x100000;
-
-	puts("    DDR: ");
-	return dram_size;
-}