diff options
Diffstat (limited to 'qemu/roms/u-boot/board/esd/tasreg/tasreg.c')
| -rw-r--r-- | qemu/roms/u-boot/board/esd/tasreg/tasreg.c | 432 |
1 files changed, 432 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/board/esd/tasreg/tasreg.c b/qemu/roms/u-boot/board/esd/tasreg/tasreg.c new file mode 100644 index 000000000..09a90ed2d --- /dev/null +++ b/qemu/roms/u-boot/board/esd/tasreg/tasreg.c @@ -0,0 +1,432 @@ +/* + * (C) Copyright 2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <malloc.h> +#include <asm/m5249.h> +#include <asm/io.h> + + +/* Prototypes */ +int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len); +int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len); + + +#if 0 +#define FPGA_DEBUG +#endif + +/* predefine these here for FPGA programming (before including fpga.c) */ +#define SET_FPGA(data) mbar2_writeLong(MCFSIM_GPIO1_OUT, data) +#define FPGA_DONE_STATE (mbar2_readLong(MCFSIM_GPIO1_READ) & CONFIG_SYS_FPGA_DONE) +#define FPGA_INIT_STATE (mbar2_readLong(MCFSIM_GPIO1_READ) & CONFIG_SYS_FPGA_INIT) +#define FPGA_PROG_ACTIVE_HIGH /* on this platform is PROG active high! */ +#define out32(a,b) /* nothing to do (gpio already configured) */ + + +/* fpga configuration data - generated by bin2cc */ +const unsigned char fpgadata[] = +{ +#include "fpgadata.c" +}; + +/* + * include common fpga code (for esd boards) + */ +#include "../common/fpga.c" + + +int checkboard (void) { + ulong val; + uchar val8; + + puts ("Board: "); + puts("esd TASREG"); + val8 = ((uchar)~((uchar)mbar2_readLong(MCFSIM_GPIO1_READ) >> 4)) & 0xf; + printf(" (Switch=%1X)\n", val8); + + /* + * Set LED on + */ + val = mbar2_readLong(MCFSIM_GPIO1_OUT) & ~CONFIG_SYS_GPIO1_LED; + mbar2_writeLong(MCFSIM_GPIO1_OUT, val); /* Set LED on */ + + return 0; +}; + + +phys_size_t initdram (int board_type) { + unsigned long junk = 0xa5a59696; + + /* + * Note: + * RC = ([(RefreshTime/#rows) / (1/BusClk)] / 16) - 1 + */ + +#ifdef CONFIG_SYS_FAST_CLK + /* + * Busclk=70MHz, RefreshTime=64ms, #rows=4096 (4K) + * SO=1, NAM=0, COC=0, RTIM=01 (6clk refresh), RC=39 + */ + mbar_writeShort(MCFSIM_DCR, 0x8239); +#elif CONFIG_SYS_PLL_BYPASS + /* + * Busclk=5.6448MHz, RefreshTime=64ms, #rows=8192 (8K) + * SO=1, NAM=0, COC=0, RTIM=01 (6clk refresh), RC=02 + */ + mbar_writeShort(MCFSIM_DCR, 0x8202); +#else + /* + * Busclk=36MHz, RefreshTime=64ms, #rows=4096 (4K) + * SO=1, NAM=0, COC=0, RTIM=01 (6clk refresh), RC=22 (562 bus clock cycles) + */ + mbar_writeShort(MCFSIM_DCR, 0x8222); +#endif + + /* + * SDRAM starts at 0x0000_0000, CASL=10, CBM=010, PS=10 (16bit port), + * PM=1 (continuous page mode) + */ + + /* RE=0 (keep auto-refresh disabled while setting up registers) */ + mbar_writeLong(MCFSIM_DACR0, 0x00003324); + + /* BAM=007c (bits 22,21 are bank selects; 256kB blocks) */ + mbar_writeLong(MCFSIM_DMR0, 0x01fc0001); + + /** Precharge sequence **/ + mbar_writeLong(MCFSIM_DACR0, 0x0000332c); /* Set DACR0[IP] (bit 3) */ + out_be32((void *)0, junk); /* write to a memory location to init. precharge */ + udelay(0x10); /* Allow several Precharge cycles */ + + /** Refresh Sequence **/ + mbar_writeLong(MCFSIM_DACR0, 0x0000b324); /* Enable the refresh bit, DACR0[RE] (bit 15) */ + udelay(0x7d0); /* Allow gobs of refresh cycles */ + + /** Mode Register initialization **/ + mbar_writeLong(MCFSIM_DACR0, 0x0000b364); /* Enable DACR0[IMRS] (bit 6); RE remains enabled */ + out_be32((void *)0x800, junk); /* Access RAM to initialize the mode register */ + + return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; +}; + + +int testdram (void) { + /* TODO: XXX XXX XXX */ + printf ("DRAM test not implemented!\n"); + + return (0); +} + + +int misc_init_r (void) +{ + unsigned char *dst; + ulong len = sizeof(fpgadata); + int status; + int index; + int i; + uchar buf[8]; + + dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE); + if (gunzip (dst, CONFIG_SYS_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) { + printf ("GUNZIP ERROR - must RESET board to recover\n"); + do_reset (NULL, 0, 0, NULL); + } + + status = fpga_boot(dst, len); + if (status != 0) { + printf("\nFPGA: Booting failed "); + switch (status) { + case ERROR_FPGA_PRG_INIT_LOW: + printf("(Timeout: INIT not low after asserting PROGRAM*)\n "); + break; + case ERROR_FPGA_PRG_INIT_HIGH: + printf("(Timeout: INIT not high after deasserting PROGRAM*)\n "); + break; + case ERROR_FPGA_PRG_DONE: + printf("(Timeout: DONE not high after programming FPGA)\n "); + break; + } + + /* display infos on fpgaimage */ + index = 15; + for (i=0; i<4; i++) { + len = dst[index]; + printf("FPGA: %s\n", &(dst[index+1])); + index += len+3; + } + putc ('\n'); + /* delayed reboot */ + for (i=20; i>0; i--) { + printf("Rebooting in %2d seconds \r",i); + for (index=0;index<1000;index++) + udelay(1000); + } + putc ('\n'); + do_reset(NULL, 0, 0, NULL); + } + + puts("FPGA: "); + + /* display infos on fpgaimage */ + index = 15; + for (i=0; i<4; i++) { + len = dst[index]; + printf("%s ", &(dst[index+1])); + index += len+3; + } + putc ('\n'); + + free(dst); + + /* + * + */ + buf[0] = 0x00; + buf[1] = 0x32; + buf[2] = 0x3f; + i2c_write(0x38, 0, 0, buf, 3); + + return (0); +} + + +#if 1 /* test-only: board specific test commands */ +int i2c_probe(uchar addr); + +/* + */ +int do_iploop(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + ulong addr; + + if (argc < 2) { + puts("ERROR!\n"); + return -1; + } + + addr = simple_strtol (argv[1], NULL, 16); + + printf("i2c probe looping on addr 0x%lx (cntrl-c aborts)...\n", addr); + + for (;;) { + i2c_probe(addr); + + /* Abort if ctrl-c was pressed */ + if (ctrlc()) { + puts("\nAbort\n"); + return 0; + } + + udelay(1000); + } + + return 0; +} +U_BOOT_CMD( + iploop, 2, 1, do_iploop, + "i2c probe loop <addr>", + "" +); + +/* + */ +int do_codec(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + uchar buf[8]; + + out_be16((void *)0xe0000000, 0x4000); + + udelay(5000); /* wait for 5ms */ + + buf[0] = 0x10; + buf[1] = 0x07; + buf[2] = 0x03; + i2c_write(0x10, 0, 0, buf, 3); + + buf[0] = 0x10; + buf[1] = 0x01; + buf[2] = 0x80; + i2c_write(0x10, 0, 0, buf, 3); + + buf[0] = 0x10; + buf[1] = 0x02; + buf[2] = 0x03; + i2c_write(0x10, 0, 0, buf, 3); + + buf[0] = 0x10; + buf[1] = 0x03; + buf[2] = 0x29; + i2c_write(0x10, 0, 0, buf, 3); + + buf[0] = 0x10; + buf[1] = 0x04; + buf[2] = 0x00; + i2c_write(0x10, 0, 0, buf, 3); + + buf[0] = 0x10; + buf[1] = 0x05; + buf[2] = 0x00; + i2c_write(0x10, 0, 0, buf, 3); + + buf[0] = 0x10; + buf[1] = 0x07; + buf[2] = 0x02; + i2c_write(0x10, 0, 0, buf, 3); + + return 0; +} +U_BOOT_CMD( + codec, 1, 1, do_codec, + "Enable codec", + "" +); + +/* + */ +int do_saa(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + ulong addr; + ulong instr; + ulong cntrl; + ulong data; + uchar buf[8]; + + if (argc < 5) { + puts("ERROR!\n"); + return -1; + } + + addr = simple_strtol (argv[1], NULL, 16); + instr = simple_strtol (argv[2], NULL, 16); + cntrl = simple_strtol (argv[3], NULL, 16); + data = simple_strtol (argv[4], NULL, 16); + + buf[0] = (uchar)instr; + buf[1] = (uchar)cntrl; + buf[2] = (uchar)data; + i2c_write(addr, 0, 0, buf, 3); + + return 0; +} +U_BOOT_CMD( + saa, 5, 1, do_saa, + "Write to SAA1064 <addr> <instr> <cntrl> <data>", + "" +); + +/* + */ +int do_iwrite(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + ulong addr; + ulong data0; + ulong data1; + ulong data2; + ulong data3; + uchar buf[8]; + int cnt; + + if (argc < 3) { + puts("ERROR!\n"); + return -1; + } + + addr = simple_strtol (argv[1], NULL, 16); + cnt = simple_strtol (argv[2], NULL, 16); + data0 = simple_strtol (argv[3], NULL, 16); + data1 = simple_strtol (argv[4], NULL, 16); + data2 = simple_strtol (argv[5], NULL, 16); + data3 = simple_strtol (argv[6], NULL, 16); + + printf("Writing %d bytes to device %lx!\n", cnt, addr); + buf[0] = (uchar)data0; + buf[1] = (uchar)data1; + buf[2] = (uchar)data2; + buf[3] = (uchar)data3; + i2c_write(addr, 0, 0, buf, cnt); + + return 0; +} +U_BOOT_CMD( + iwrite, 6, 1, do_iwrite, + "Write n bytes to I2C-device", + "addr cnt data0 ... datan" +); + +/* + */ +int do_iread(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + ulong addr; + ulong cnt; + uchar buf[32]; + int i; + + if (argc < 3) { + puts("ERROR!\n"); + return -1; + } + + addr = simple_strtol (argv[1], NULL, 16); + cnt = simple_strtol (argv[2], NULL, 16); + + i2c_read(addr, 0, 0, buf, cnt); + printf("I2C Data:"); + for (i=0; i<cnt; i++) { + printf(" %02X", buf[i]); + } + printf("\n"); + + return 0; +} +U_BOOT_CMD( + iread, 3, 1, do_iread, + "Read from I2C <addr> <cnt>", + "" +); + +/* + */ +int do_ireadl(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + ulong addr; + uchar buf[32]; + int cnt; + + if (argc < 2) { + puts("ERROR!\n"); + return -1; + } + + addr = simple_strtol (argv[1], NULL, 16); + cnt = 1; + + printf("iread looping on addr 0x%lx (cntrl-c aborts)...\n", addr); + + for (;;) { + i2c_read(addr, 0, 0, buf, cnt); + + /* Abort if ctrl-c was pressed */ + if (ctrlc()) { + puts("\nAbort\n"); + return 0; + } + + udelay(3000); + } + + return 0; +} +U_BOOT_CMD( + ireadl, 2, 1, do_ireadl, + "Read-loop from I2C <addr>", + "" +); +#endif |