diff options
Diffstat (limited to 'qemu/roms/u-boot/board/amcc/redwood')
| -rw-r--r-- | qemu/roms/u-boot/board/amcc/redwood/Makefile | 9 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/amcc/redwood/config.mk | 20 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/amcc/redwood/init.S | 62 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/amcc/redwood/redwood.c | 440 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/amcc/redwood/redwood.h | 34 |
5 files changed, 565 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/board/amcc/redwood/Makefile b/qemu/roms/u-boot/board/amcc/redwood/Makefile new file mode 100644 index 000000000..2bc632b24 --- /dev/null +++ b/qemu/roms/u-boot/board/amcc/redwood/Makefile @@ -0,0 +1,9 @@ +# +# (C) Copyright 2008 +# Feng Kan, Applied Micro Circuits Corp., fkan@amcc.com. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y = redwood.o +extra-y += init.o diff --git a/qemu/roms/u-boot/board/amcc/redwood/config.mk b/qemu/roms/u-boot/board/amcc/redwood/config.mk new file mode 100644 index 000000000..42b3e5f49 --- /dev/null +++ b/qemu/roms/u-boot/board/amcc/redwood/config.mk @@ -0,0 +1,20 @@ +# +# (C) Copyright 2008 +# Feng Kan, Applied Micro Circuits Corp., fkan@amcc.com. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +# +# AMCC 460SX Reference Platform (redwood) board +# + +PLATFORM_CPPFLAGS += -DCONFIG_440=1 + +ifeq ($(debug),1) +PLATFORM_CPPFLAGS += -DDEBUG +endif + +ifeq ($(dbcr),1) +PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000 +endif diff --git a/qemu/roms/u-boot/board/amcc/redwood/init.S b/qemu/roms/u-boot/board/amcc/redwood/init.S new file mode 100644 index 000000000..fd0513087 --- /dev/null +++ b/qemu/roms/u-boot/board/amcc/redwood/init.S @@ -0,0 +1,62 @@ +/* + * (C) Copyright 2008 + * Feng Kan, Applied Micro Circuits Corp., fkan@amcc.com. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <ppc_asm.tmpl> +#include <config.h> +#include <asm/mmu.h> +#include <asm/ppc4xx.h> + +/************************************************************************** + * TLB TABLE + * + * This table is used by the cpu boot code to setup the initial tlb + * entries. Rather than make broad assumptions in the cpu source tree, + * this table lets each board set things up however they like. + * + * Pointer to the table is returned in r1 + * + *************************************************************************/ + + .section .bootpg,"ax" + .globl tlbtab +tlbtab: + tlbtab_start + + /* + * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the + * speed up boot process. It is patched after relocation to enable SA_I + */ + tlbentry(0xff000000, SZ_16M, 0xff000000, 4, AC_RWX | SA_G) + + /* + * TLB entries for SDRAM are not needed on this platform. + * They are dynamically generated in the SPD DDR(2) detection + * routine. + */ + + /* Although 512 KB, map 256k at a time */ + tlbentry(CONFIG_SYS_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_RWX | SA_I) + tlbentry(CONFIG_SYS_ISRAM_BASE + 0x40000, SZ_256K, 0x00040000, 4, AC_RWX | SA_I) + + tlbentry(CONFIG_SYS_OPER_FLASH, SZ_16M, 0xE7000000, 4,AC_RWX | SA_IG) + + /* + * Peripheral base + */ + tlbentry(CONFIG_SYS_PERIPHERAL_BASE, SZ_16K, 0xEF600000, 4, AC_RW | SA_IG) + + tlbentry(CONFIG_SYS_PCIE0_XCFGBASE,SZ_16M, 0x00000000, 0xC, AC_RW | SA_IG) + tlbentry(CONFIG_SYS_PCIE1_XCFGBASE,SZ_16M, 0x10000000, 0xC, AC_RW | SA_IG) + tlbentry(CONFIG_SYS_PCIE2_XCFGBASE,SZ_16M, 0x20000000, 0xC, AC_RW | SA_IG) + + tlbentry(CONFIG_SYS_PCIE0_MEMBASE, SZ_256M, 0x00000000, 0xD, AC_RW | SA_IG) + tlbentry(CONFIG_SYS_PCIE1_MEMBASE, SZ_256M, 0x00000000, 0xE, AC_RW | SA_IG) + + tlbentry(CONFIG_SYS_PCIE0_REGBASE, SZ_64K, 0x30000000, 0xC, AC_RW | SA_IG) + tlbentry(CONFIG_SYS_PCIE1_REGBASE, SZ_64K, 0x30010000, 0xC, AC_RW | SA_IG) + tlbentry(CONFIG_SYS_PCIE2_REGBASE, SZ_64K, 0x30020000, 0xC, AC_RW | SA_IG) + tlbtab_end diff --git a/qemu/roms/u-boot/board/amcc/redwood/redwood.c b/qemu/roms/u-boot/board/amcc/redwood/redwood.c new file mode 100644 index 000000000..15c38840d --- /dev/null +++ b/qemu/roms/u-boot/board/amcc/redwood/redwood.c @@ -0,0 +1,440 @@ +/* + * This is the main board level file for the Redwood AMCC board. + * + * (C) Copyright 2008 + * Feng Kan, Applied Micro Circuits Corp., fkan@amcc.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include "redwood.h" +#include <asm/ppc4xx.h> +#include <asm/processor.h> +#include <i2c.h> +#include <asm/io.h> + +int compare_to_true(char *str); +char *remove_l_w_space(char *in_str); +char *remove_t_w_space(char *in_str); +int get_console_port(void); + +static void early_init_EBC(void); +static int bootdevice_selected(void); +static void early_reinit_EBC(int); +static void early_init_UIC(void); + +/* + * Define Boot devices + */ +#define BOOT_FROM_8BIT_SRAM 0x00 +#define BOOT_FROM_16BIT_SRAM 0x01 +#define BOOT_FROM_32BIT_SRAM 0x02 +#define BOOT_FROM_8BIT_NAND 0x03 +#define BOOT_FROM_16BIT_NOR 0x04 +#define BOOT_DEVICE_UNKNOWN 0xff + +/* + * EBC Devices Characteristics + * Peripheral Bank Access Parameters - EBC_BxAP + * Peripheral Bank Configuration Register - EBC_BxCR + */ + +/* + * 8 bit width SRAM + * BU Value + * BxAP : 0x03800000 - 0 00000111 0 00 00 00 00 00 000 0 0 0 0 00000 + * B0CR : 0xff098000 - BAS = ff0 - 100 11 00 0000000000000 + * B2CR : 0xe7098000 - BAS = e70 - 100 11 00 0000000000000 + */ +#define EBC_BXAP_8BIT_SRAM \ + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(7) | \ + EBC_BXAP_BCE_DISABLE | EBC_BXAP_BCT_2TRANS | \ + EBC_BXAP_CSN_ENCODE(0) | EBC_BXAP_OEN_ENCODE(0) | \ + EBC_BXAP_WBN_ENCODE(0) | EBC_BXAP_WBF_ENCODE(0) | \ + EBC_BXAP_TH_ENCODE(0) | EBC_BXAP_RE_DISABLED | \ + EBC_BXAP_SOR_DELAYED | EBC_BXAP_BEM_WRITEONLY | \ + EBC_BXAP_PEN_DISABLED + +#define EBC_BXAP_16BIT_SRAM EBC_BXAP_8BIT_SRAM +#define EBC_BXAP_32BIT_SRAM EBC_BXAP_8BIT_SRAM + +/* + * NAND flash + * BU Value + * BxAP : 0x048ff240 - 0 00000111 0 00 00 00 00 00 000 0 0 0 0 00000 + * B0CR : 0xff09a000 - BAS = ff0 - 100 11 01 0000000000000 + * B2CR : 0xe709a000 - BAS = e70 - 100 11 01 0000000000000 +*/ +#define EBC_BXAP_NAND \ + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(7) | \ + EBC_BXAP_BCE_DISABLE | EBC_BXAP_BCT_2TRANS | \ + EBC_BXAP_CSN_ENCODE(0) | EBC_BXAP_OEN_ENCODE(0) | \ + EBC_BXAP_WBN_ENCODE(0) | EBC_BXAP_WBF_ENCODE(0) | \ + EBC_BXAP_TH_ENCODE(0) | EBC_BXAP_RE_DISABLED | \ + EBC_BXAP_SOR_DELAYED | EBC_BXAP_BEM_WRITEONLY | \ + EBC_BXAP_PEN_DISABLED + +/* + * NOR flash + * BU Value + * BxAP : 0x048ff240 - 0 00000111 0 00 00 00 00 00 000 0 0 0 0 00000 + * B0CR : 0xff09a000 - BAS = ff0 - 100 11 01 0000000000000 + * B2CR : 0xe709a000 - BAS = e70 - 100 11 01 0000000000000 +*/ +#define EBC_BXAP_NOR \ + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(7) | \ + EBC_BXAP_BCE_DISABLE | EBC_BXAP_BCT_2TRANS | \ + EBC_BXAP_CSN_ENCODE(0) | EBC_BXAP_OEN_ENCODE(0) | \ + EBC_BXAP_WBN_ENCODE(0) | EBC_BXAP_WBF_ENCODE(0) | \ + EBC_BXAP_TH_ENCODE(0) | EBC_BXAP_RE_DISABLED | \ + EBC_BXAP_SOR_DELAYED | EBC_BXAP_BEM_WRITEONLY | \ + EBC_BXAP_PEN_DISABLED + +/* + * FPGA + * BU value : + * B1AP = 0x05895240 - 0 00001011 0 00 10 01 01 01 001 0 0 1 0 00000 + * B1CR = 0xe201a000 - BAS = e20 - 000 11 01 00000000000000 + */ +#define EBC_BXAP_FPGA \ + EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(11) | \ + EBC_BXAP_BCE_DISABLE | EBC_BXAP_BCT_2TRANS | \ + EBC_BXAP_CSN_ENCODE(10) | EBC_BXAP_OEN_ENCODE(1) | \ + EBC_BXAP_WBN_ENCODE(1) | EBC_BXAP_WBF_ENCODE(1) | \ + EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_RE_DISABLED | \ + EBC_BXAP_SOR_DELAYED | EBC_BXAP_BEM_RW | \ + EBC_BXAP_PEN_DISABLED + +#define EBC_BXCR_8BIT_SRAM_CS0 \ + EBC_BXCR_BAS_ENCODE(0xFFE00000) | EBC_BXCR_BS_1MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT + +#define EBC_BXCR_32BIT_SRAM_CS0 \ + EBC_BXCR_BAS_ENCODE(0xFFC00000) | EBC_BXCR_BS_1MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT + +#define EBC_BXCR_NAND_CS0 \ + EBC_BXCR_BAS_ENCODE(0xFF000000) | EBC_BXCR_BS_16MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT + +#define EBC_BXCR_16BIT_SRAM_CS0 \ + EBC_BXCR_BAS_ENCODE(0xFFE00000) | EBC_BXCR_BS_2MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT + +#define EBC_BXCR_NOR_CS0 \ + EBC_BXCR_BAS_ENCODE(0xFF000000) | EBC_BXCR_BS_16MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT + +#define EBC_BXCR_NOR_CS1 \ + EBC_BXCR_BAS_ENCODE(0xE0000000) | EBC_BXCR_BS_128MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT + +#define EBC_BXCR_NAND_CS1 \ + EBC_BXCR_BAS_ENCODE(0xE0000000) | EBC_BXCR_BS_128MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT + +#define EBC_BXCR_NAND_CS2 \ + EBC_BXCR_BAS_ENCODE(0xC0000000) | EBC_BXCR_BS_128MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT + +#define EBC_BXCR_SRAM_CS2 \ + EBC_BXCR_BAS_ENCODE(0xC0000000) | EBC_BXCR_BS_4MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT + +#define EBC_BXCR_LARGE_FLASH_CS2 \ + EBC_BXCR_BAS_ENCODE(0xE7000000) | EBC_BXCR_BS_16MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT + +#define EBC_BXCR_FPGA_CS3 \ + EBC_BXCR_BAS_ENCODE(0xE2000000) | EBC_BXCR_BS_1MB | \ + EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT + +/***************************************************************************** + * UBOOT initiated board specific function calls + ****************************************************************************/ + +int board_early_init_f(void) +{ + int computed_boot_device = BOOT_DEVICE_UNKNOWN; + + /* + * Initialise EBC + */ + early_init_EBC(); + + /* + * Determine which boot device was selected + */ + computed_boot_device = bootdevice_selected(); + + /* + * Reinit EBC based on selected boot device + */ + early_reinit_EBC(computed_boot_device); + + /* + * Setup for UIC on 460SX redwood board + */ + early_init_UIC(); + + return 0; +} + +int checkboard(void) +{ + char buf[64]; + int i = getenv_f("serial#", buf, sizeof(buf)); + + printf("Board: Redwood - AMCC 460SX Reference Board"); + if (i > 0) { + puts(", serial# "); + puts(buf); + } + putc('\n'); + + return 0; +} + +static void early_init_EBC(void) +{ + /* + * Initialize EBC CONFIG - + * Keep the Default value, but the bit PDT which has to be set to 1 ?TBC + * default value : + * 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000 + */ + mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK | + EBC_CFG_PTD_ENABLE | + EBC_CFG_RTC_16PERCLK | + EBC_CFG_ATC_PREVIOUS | + EBC_CFG_DTC_PREVIOUS | + EBC_CFG_CTC_PREVIOUS | + EBC_CFG_OEO_PREVIOUS | + EBC_CFG_EMC_DEFAULT | EBC_CFG_PME_DISABLE | EBC_CFG_PR_16); + + /* + * PART 1 : Initialize EBC Bank 3 + * ============================== + * Bank1 is always associated to the EPLD. + * It has to be initialized prior to other banks settings computation + * since some board registers values may be needed to determine the + * boot type + */ + mtebc(PB1AP, EBC_BXAP_FPGA); + mtebc(PB1CR, EBC_BXCR_FPGA_CS3); + +} + +static int bootdevice_selected(void) +{ + unsigned long sdr0_pinstp; + unsigned long bootstrap_settings; + int computed_boot_device = BOOT_DEVICE_UNKNOWN; + + /* + * Determine which boot device was selected + * ================================================= + * + * Read Pin Strap Register in PPC460SX + * Result can either be : + * - Boot strap = boot from EBC 8bits => Small Flash + * - Boot strap = boot from PCI + * - Boot strap = IIC + * In case of boot from IIC, read Serial Device Strap Register1 + * + * Result can either be : + * - Boot from EBC - EBC Bus Width = 8bits => Small Flash + * - Boot from EBC - EBC Bus Width = 16bits => Large Flash or SRAM + * - Boot from PCI + */ + + /* Read Pin Strap Register in PPC460SX */ + mfsdr(SDR0_PINSTP, sdr0_pinstp); + bootstrap_settings = sdr0_pinstp & SDR0_PSTRP0_BOOTSTRAP_MASK; + + switch (bootstrap_settings) { + case SDR0_PSTRP0_BOOTSTRAP_SETTINGS0: + /* + * Boot from SRAM, 8bit width + */ + computed_boot_device = BOOT_FROM_8BIT_SRAM; + break; + case SDR0_PSTRP0_BOOTSTRAP_SETTINGS1: + /* + * Boot from SRAM, 32bit width + */ + computed_boot_device = BOOT_FROM_32BIT_SRAM; + break; + case SDR0_PSTRP0_BOOTSTRAP_SETTINGS2: + /* + * Boot from NAND, 8bit width + */ + computed_boot_device = BOOT_FROM_8BIT_NAND; + break; + case SDR0_PSTRP0_BOOTSTRAP_SETTINGS4: + /* + * Boot from SRAM, 16bit width + * Boot setting in IIC EEPROM 0x50 + */ + computed_boot_device = BOOT_FROM_16BIT_SRAM; + break; + case SDR0_PSTRP0_BOOTSTRAP_SETTINGS5: + /* + * Boot from NOR, 16bit width + * Boot setting in IIC EEPROM 0x54 + */ + computed_boot_device = BOOT_FROM_16BIT_NOR; + break; + default: + /* should not be */ + computed_boot_device = BOOT_DEVICE_UNKNOWN; + break; + } + + return computed_boot_device; +} + +static void early_reinit_EBC(int computed_boot_device) +{ + /* + * Compute EBC settings depending on selected boot device + * ====================================================== + * + * Resulting EBC init will be among following configurations : + * + * - Boot from EBC 8bits => boot from Small Flash selected + * EBC-CS0 = Small Flash + * EBC-CS2 = Large Flash and SRAM + * + * - Boot from EBC 16bits => boot from Large Flash or SRAM + * EBC-CS0 = Large Flash or SRAM + * EBC-CS2 = Small Flash + * + * - Boot from PCI + * EBC-CS0 = not initialized to avoid address contention + * EBC-CS2 = same as boot from Small Flash selected + */ + + unsigned long ebc0_cs0_bxap_value = 0, ebc0_cs0_bxcr_value = 0; + unsigned long ebc0_cs1_bxap_value = 0, ebc0_cs1_bxcr_value = 0; + unsigned long ebc0_cs2_bxap_value = 0, ebc0_cs2_bxcr_value = 0; + + switch (computed_boot_device) { + /*-------------------------------------------------------------------*/ + case BOOT_FROM_8BIT_SRAM: + /*-------------------------------------------------------------------*/ + ebc0_cs0_bxap_value = EBC_BXAP_8BIT_SRAM; + ebc0_cs0_bxcr_value = EBC_BXCR_8BIT_SRAM_CS0; + ebc0_cs1_bxap_value = EBC_BXAP_NOR; + ebc0_cs1_bxcr_value = EBC_BXCR_NOR_CS1; + ebc0_cs2_bxap_value = EBC_BXAP_NAND; + ebc0_cs2_bxcr_value = EBC_BXCR_NAND_CS2; + break; + + /*-------------------------------------------------------------------*/ + case BOOT_FROM_16BIT_SRAM: + /*-------------------------------------------------------------------*/ + ebc0_cs0_bxap_value = EBC_BXAP_16BIT_SRAM; + ebc0_cs0_bxcr_value = EBC_BXCR_16BIT_SRAM_CS0; + ebc0_cs1_bxap_value = EBC_BXAP_NOR; + ebc0_cs1_bxcr_value = EBC_BXCR_NOR_CS1; + ebc0_cs2_bxap_value = EBC_BXAP_NAND; + ebc0_cs2_bxcr_value = EBC_BXCR_NAND_CS2; + break; + + /*-------------------------------------------------------------------*/ + case BOOT_FROM_32BIT_SRAM: + /*-------------------------------------------------------------------*/ + ebc0_cs0_bxap_value = EBC_BXAP_32BIT_SRAM; + ebc0_cs0_bxcr_value = EBC_BXCR_32BIT_SRAM_CS0; + ebc0_cs1_bxap_value = EBC_BXAP_NOR; + ebc0_cs1_bxcr_value = EBC_BXCR_NOR_CS1; + ebc0_cs2_bxap_value = EBC_BXAP_NAND; + ebc0_cs2_bxcr_value = EBC_BXCR_NAND_CS2; + break; + + /*-------------------------------------------------------------------*/ + case BOOT_FROM_16BIT_NOR: + /*-------------------------------------------------------------------*/ + ebc0_cs0_bxap_value = EBC_BXAP_NOR; + ebc0_cs0_bxcr_value = EBC_BXCR_NOR_CS0; + ebc0_cs1_bxap_value = EBC_BXAP_NAND; + ebc0_cs1_bxcr_value = EBC_BXCR_NAND_CS1; + ebc0_cs2_bxap_value = EBC_BXAP_32BIT_SRAM; + ebc0_cs2_bxcr_value = EBC_BXCR_SRAM_CS2; + break; + + /*-------------------------------------------------------------------*/ + case BOOT_FROM_8BIT_NAND: + /*-------------------------------------------------------------------*/ + ebc0_cs0_bxap_value = EBC_BXAP_NAND; + ebc0_cs0_bxcr_value = EBC_BXCR_NAND_CS0; + ebc0_cs1_bxap_value = EBC_BXAP_NOR; + ebc0_cs1_bxcr_value = EBC_BXCR_NOR_CS1; + ebc0_cs2_bxap_value = EBC_BXAP_32BIT_SRAM; + ebc0_cs2_bxcr_value = EBC_BXCR_SRAM_CS2; + break; + + /*-------------------------------------------------------------------*/ + default: + /*-------------------------------------------------------------------*/ + /* BOOT_DEVICE_UNKNOWN */ + break; + } + + mtebc(PB0AP, ebc0_cs0_bxap_value); + mtebc(PB0CR, ebc0_cs0_bxcr_value); + mtebc(PB1AP, ebc0_cs1_bxap_value); + mtebc(PB1CR, ebc0_cs1_bxcr_value); + mtebc(PB2AP, ebc0_cs2_bxap_value); + mtebc(PB2CR, ebc0_cs2_bxcr_value); +} + +static void early_init_UIC(void) +{ + /* + * Initialise UIC registers. Clear all interrupts. Disable all + * interrupts. + * Set critical interrupt values. Set interrupt polarities. Set + * interrupt trigger levels. Make bit 0 High priority. Clear all + * interrupts again. + */ + mtdcr(UIC3SR, 0xffffffff); /* Clear all interrupts */ + mtdcr(UIC3ER, 0x00000000); /* disable all interrupts */ + mtdcr(UIC3CR, 0x00000000); /* Set Critical / Non Critical + * interrupts */ + mtdcr(UIC3PR, 0xffffffff); /* Set Interrupt Polarities */ + mtdcr(UIC3TR, 0x001fffff); /* Set Interrupt Trigger Levels */ + mtdcr(UIC3VR, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(UIC3SR, 0xffffffff); /* clear all interrupts */ + + mtdcr(UIC2SR, 0xffffffff); /* Clear all interrupts */ + mtdcr(UIC2ER, 0x00000000); /* disable all interrupts */ + mtdcr(UIC2CR, 0x00000000); /* Set Critical / Non Critical + * interrupts */ + mtdcr(UIC2PR, 0xebebebff); /* Set Interrupt Polarities */ + mtdcr(UIC2TR, 0x74747400); /* Set Interrupt Trigger Levels */ + mtdcr(UIC2VR, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(UIC2SR, 0xffffffff); /* clear all interrupts */ + + mtdcr(UIC1SR, 0xffffffff); /* Clear all interrupts */ + mtdcr(UIC1ER, 0x00000000); /* disable all interrupts */ + mtdcr(UIC1CR, 0x00000000); /* Set Critical / Non Critical + * interrupts */ + mtdcr(UIC1PR, 0xffffffff); /* Set Interrupt Polarities */ + mtdcr(UIC1TR, 0x001fc0ff); /* Set Interrupt Trigger Levels */ + mtdcr(UIC1VR, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(UIC1SR, 0xffffffff); /* clear all interrupts */ + + mtdcr(UIC0SR, 0xffffffff); /* Clear all interrupts */ + mtdcr(UIC0ER, 0x00000000); /* disable all interrupts excepted + * cascade to be checked */ + mtdcr(UIC0CR, 0x00104001); /* Set Critical / Non Critical + * interrupts */ + mtdcr(UIC0PR, 0xffffffff); /* Set Interrupt Polarities */ + mtdcr(UIC0TR, 0x000f003c); /* Set Interrupt Trigger Levels */ + mtdcr(UIC0VR, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(UIC0SR, 0xffffffff); /* clear all interrupts */ + +} diff --git a/qemu/roms/u-boot/board/amcc/redwood/redwood.h b/qemu/roms/u-boot/board/amcc/redwood/redwood.h new file mode 100644 index 000000000..9c36073c2 --- /dev/null +++ b/qemu/roms/u-boot/board/amcc/redwood/redwood.h @@ -0,0 +1,34 @@ +/* + * (C) Copyright 2008 + * Feng Kan, Applied Micro Circuit Corp., fkan@amcc.com. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __REDWOOD_H_ +#define __REDWOOD_H_ + +#ifdef __cplusplus +extern "C" { +#endif + +/*----------------------------------------------------------------------------+ +| Defines ++----------------------------------------------------------------------------*/ +/* Pin Straps Reg */ +#define SDR0_PSTRP0 0x0040 +#define SDR0_PSTRP0_BOOTSTRAP_MASK 0xE0000000 /* Strap Bits */ + +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS0 0x00000000 /* Default strap settings 0 */ +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS1 0x20000000 /* Default strap settings 1 */ +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS2 0x40000000 /* Default strap settings 2 */ +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS3 0x60000000 /* Default strap settings 3 */ +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS4 0x80000000 /* Default strap settings 4 */ +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS5 0xA0000000 /* Default strap settings 5 */ +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS6 0xC0000000 /* Default strap settings 6 */ +#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS7 0xE0000000 /* Default strap settings 7 */ + +#ifdef __cplusplus +} +#endif +#endif /* __REDWOOD_H_ */ |