diff options
Diffstat (limited to 'qemu/roms/seabios/src/hw/ahci.h')
| -rw-r--r-- | qemu/roms/seabios/src/hw/ahci.h | 202 |
1 files changed, 202 insertions, 0 deletions
diff --git a/qemu/roms/seabios/src/hw/ahci.h b/qemu/roms/seabios/src/hw/ahci.h new file mode 100644 index 000000000..c8c755a3f --- /dev/null +++ b/qemu/roms/seabios/src/hw/ahci.h @@ -0,0 +1,202 @@ +#ifndef __AHCI_H +#define __AHCI_H + +#include "block.h" // struct drive_s +#include "types.h" // u32 + +struct sata_cmd_fis { + u8 reg; + u8 pmp_type; + u8 command; + u8 feature; + + u8 lba_low; + u8 lba_mid; + u8 lba_high; + u8 device; + + u8 lba_low2; + u8 lba_mid2; + u8 lba_high2; + u8 feature2; + + u8 sector_count; + u8 sector_count2; + u8 res_1; + u8 control; + + u8 res_2[64 - 16]; +}; + +struct ahci_ctrl_s { + struct pci_device *pci_tmp; + u16 pci_bdf; + u8 irq; + u32 iobase; + u32 caps; + u32 ports; +}; + +struct ahci_cmd_s { + struct sata_cmd_fis fis; + u8 atapi[0x20]; + u8 res[0x20]; + struct { + u32 base; + u32 baseu; + u32 res; + u32 flags; + } prdt[]; +}; + +/* command list */ +struct ahci_list_s { + u32 flags; + u32 bytes; + u32 base; + u32 baseu; + u32 res[4]; +}; + +struct ahci_fis_s { + u8 dsfis[0x1c]; /* dma setup */ + u8 res_1[0x04]; + u8 psfis[0x14]; /* pio setup */ + u8 res_2[0x0c]; + u8 rfis[0x14]; /* d2h register */ + u8 res_3[0x04]; + u8 sdbfis[0x08]; /* set device bits */ + u8 ufis[0x40]; /* unknown */ + u8 res_4[0x60]; +}; + +struct ahci_port_s { + struct drive_s drive; + struct ahci_ctrl_s *ctrl; + struct ahci_list_s *list; + struct ahci_fis_s *fis; + struct ahci_cmd_s *cmd; + u32 pnr; + u32 atapi; + char *desc; + int prio; +}; + +void ahci_setup(void); +int process_ahci_op(struct disk_op_s *op); +int ahci_cmd_data(struct disk_op_s *op, void *cdbcmd, u16 blocksize); + +#define AHCI_IRQ_ON_SG (1 << 31) +#define AHCI_CMD_ATAPI (1 << 5) +#define AHCI_CMD_WRITE (1 << 6) +#define AHCI_CMD_PREFETCH (1 << 7) +#define AHCI_CMD_RESET (1 << 8) +#define AHCI_CMD_CLR_BUSY (1 << 10) + +#define RX_FIS_D2H_REG 0x40 /* offset of D2H Register FIS data */ +#define RX_FIS_SDB 0x58 /* offset of SDB FIS data */ +#define RX_FIS_UNK 0x60 /* offset of Unknown FIS data */ + +/* global controller registers */ +#define HOST_CAP 0x00 /* host capabilities */ +#define HOST_CTL 0x04 /* global host control */ +#define HOST_IRQ_STAT 0x08 /* interrupt status */ +#define HOST_PORTS_IMPL 0x0c /* bitmap of implemented ports */ +#define HOST_VERSION 0x10 /* AHCI spec. version compliancy */ + +/* HOST_CTL bits */ +#define HOST_CTL_RESET (1 << 0) /* reset controller; self-clear */ +#define HOST_CTL_IRQ_EN (1 << 1) /* global IRQ enable */ +#define HOST_CTL_AHCI_EN (1 << 31) /* AHCI enabled */ + +/* HOST_CAP bits */ +#define HOST_CAP_SSC (1 << 14) /* Slumber capable */ +#define HOST_CAP_AHCI (1 << 18) /* AHCI only */ +#define HOST_CAP_CLO (1 << 24) /* Command List Override support */ +#define HOST_CAP_SSS (1 << 27) /* Staggered Spin-up */ +#define HOST_CAP_NCQ (1 << 30) /* Native Command Queueing */ +#define HOST_CAP_64 (1 << 31) /* PCI DAC (64-bit DMA) support */ + +/* registers for each SATA port */ +#define PORT_LST_ADDR 0x00 /* command list DMA addr */ +#define PORT_LST_ADDR_HI 0x04 /* command list DMA addr hi */ +#define PORT_FIS_ADDR 0x08 /* FIS rx buf addr */ +#define PORT_FIS_ADDR_HI 0x0c /* FIS rx buf addr hi */ +#define PORT_IRQ_STAT 0x10 /* interrupt status */ +#define PORT_IRQ_MASK 0x14 /* interrupt enable/disable mask */ +#define PORT_CMD 0x18 /* port command */ +#define PORT_TFDATA 0x20 /* taskfile data */ +#define PORT_SIG 0x24 /* device TF signature */ +#define PORT_SCR_STAT 0x28 /* SATA phy register: SStatus */ +#define PORT_SCR_CTL 0x2c /* SATA phy register: SControl */ +#define PORT_SCR_ERR 0x30 /* SATA phy register: SError */ +#define PORT_SCR_ACT 0x34 /* SATA phy register: SActive */ +#define PORT_CMD_ISSUE 0x38 /* command issue */ +#define PORT_RESERVED 0x3c /* reserved */ + +/* PORT_IRQ_{STAT,MASK} bits */ +#define PORT_IRQ_COLD_PRES (1 << 31) /* cold presence detect */ +#define PORT_IRQ_TF_ERR (1 << 30) /* task file error */ +#define PORT_IRQ_HBUS_ERR (1 << 29) /* host bus fatal error */ +#define PORT_IRQ_HBUS_DATA_ERR (1 << 28) /* host bus data error */ +#define PORT_IRQ_IF_ERR (1 << 27) /* interface fatal error */ +#define PORT_IRQ_IF_NONFATAL (1 << 26) /* interface non-fatal error */ +#define PORT_IRQ_OVERFLOW (1 << 24) /* xfer exhausted available S/G */ +#define PORT_IRQ_BAD_PMP (1 << 23) /* incorrect port multiplier */ + +#define PORT_IRQ_PHYRDY (1 << 22) /* PhyRdy changed */ +#define PORT_IRQ_DEV_ILCK (1 << 7) /* device interlock */ +#define PORT_IRQ_CONNECT (1 << 6) /* port connect change status */ +#define PORT_IRQ_SG_DONE (1 << 5) /* descriptor processed */ +#define PORT_IRQ_UNK_FIS (1 << 4) /* unknown FIS rx'd */ +#define PORT_IRQ_SDB_FIS (1 << 3) /* Set Device Bits FIS rx'd */ +#define PORT_IRQ_DMAS_FIS (1 << 2) /* DMA Setup FIS rx'd */ +#define PORT_IRQ_PIOS_FIS (1 << 1) /* PIO Setup FIS rx'd */ +#define PORT_IRQ_D2H_REG_FIS (1 << 0) /* D2H Register FIS rx'd */ + +#define PORT_IRQ_FREEZE (PORT_IRQ_HBUS_ERR | PORT_IRQ_IF_ERR | \ + PORT_IRQ_CONNECT | PORT_IRQ_PHYRDY | \ + PORT_IRQ_UNK_FIS) +#define PORT_IRQ_ERROR (PORT_IRQ_FREEZE | PORT_IRQ_TF_ERR | \ + PORT_IRQ_HBUS_DATA_ERR) +#define DEF_PORT_IRQ (PORT_IRQ_ERROR | PORT_IRQ_SG_DONE | \ + PORT_IRQ_SDB_FIS | PORT_IRQ_DMAS_FIS | \ + PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS) + +/* PORT_CMD bits */ +#define PORT_CMD_ATAPI (1 << 24) /* Device is ATAPI */ +#define PORT_CMD_LIST_ON (1 << 15) /* cmd list DMA engine running */ +#define PORT_CMD_FIS_ON (1 << 14) /* FIS DMA engine running */ +#define PORT_CMD_FIS_RX (1 << 4) /* Enable FIS receive DMA engine */ +#define PORT_CMD_CLO (1 << 3) /* Command list override */ +#define PORT_CMD_POWER_ON (1 << 2) /* Power up device */ +#define PORT_CMD_SPIN_UP (1 << 1) /* Spin up device */ +#define PORT_CMD_START (1 << 0) /* Enable port DMA engine */ + +#define PORT_CMD_ICC_MASK (0xf << 28) /* i/f ICC state mask */ +#define PORT_CMD_ICC_ACTIVE (0x1 << 28) /* Put i/f in active state */ +#define PORT_CMD_ICC_PARTIAL (0x2 << 28) /* Put i/f in partial state */ +#define PORT_CMD_ICC_SLUMBER (0x6 << 28) /* Put i/f in slumber state */ + +#define PORT_IRQ_STAT_DHRS (1 << 0) /* Device to Host Register FIS */ +#define PORT_IRQ_STAT_PSS (1 << 1) /* PIO Setup FIS */ +#define PORT_IRQ_STAT_DSS (1 << 2) /* DMA Setup FIS */ +#define PORT_IRQ_STAT_SDBS (1 << 3) /* Set Device Bits */ +#define PORT_IRQ_STAT_UFS (1 << 4) /* Unknown FIS */ +#define PORT_IRQ_STAT_DPS (1 << 5) /* Descriptor Processed */ +#define PORT_IRQ_STAT_PCS (1 << 6) /* Port Connect Change Status */ +#define PORT_IRQ_STAT_DMPS (1 << 7) /* Device Mechanical Presence + Status */ +#define PORT_IRQ_STAT_PRCS (1 << 22) /* File Ready Status */ +#define PORT_IRQ_STAT_IPMS (1 << 23) /* Incorrect Port Multiplier + Status */ +#define PORT_IRQ_STAT_OFS (1 << 24) /* Overflow Status */ +#define PORT_IRQ_STAT_INFS (1 << 26) /* Interface Non-Fatal Error + Status */ +#define PORT_IRQ_STAT_IFS (1 << 27) /* Interface Fatal Error */ +#define PORT_IRQ_STAT_HBDS (1 << 28) /* Host Bus Data Error Status */ +#define PORT_IRQ_STAT_HBFS (1 << 29) /* Host Bus Fatal Error Status */ +#define PORT_IRQ_STAT_TFES (1 << 30) /* Task File Error Status */ +#define PORT_IRQ_STAT_CPDS (1 << 31) /* Code Port Detect Status */ + +#endif // ahci.h |