diff options
Diffstat (limited to 'kernel/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c')
| -rw-r--r-- | kernel/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c | 791 |
1 files changed, 791 insertions, 0 deletions
diff --git a/kernel/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c b/kernel/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c new file mode 100644 index 000000000..19a3c3bc2 --- /dev/null +++ b/kernel/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c @@ -0,0 +1,791 @@ +/* + * Copyright (c) 2015, Sony Mobile Communications AB. + * Copyright (c) 2013, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/pinctrl/pinctrl.h> +#include <linux/pinctrl/pinmux.h> +#include <linux/pinctrl/pinconf.h> +#include <linux/pinctrl/pinconf-generic.h> +#include <linux/slab.h> +#include <linux/regmap.h> +#include <linux/gpio.h> +#include <linux/interrupt.h> +#include <linux/of_device.h> + +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> + +#include "../core.h" +#include "../pinctrl-utils.h" + +/* mode */ +#define PM8XXX_GPIO_MODE_ENABLED BIT(0) +#define PM8XXX_GPIO_MODE_INPUT 0 +#define PM8XXX_GPIO_MODE_OUTPUT 2 + +/* output buffer */ +#define PM8XXX_GPIO_PUSH_PULL 0 +#define PM8XXX_GPIO_OPEN_DRAIN 1 + +/* bias */ +#define PM8XXX_GPIO_BIAS_PU_30 0 +#define PM8XXX_GPIO_BIAS_PU_1P5 1 +#define PM8XXX_GPIO_BIAS_PU_31P5 2 +#define PM8XXX_GPIO_BIAS_PU_1P5_30 3 +#define PM8XXX_GPIO_BIAS_PD 4 +#define PM8XXX_GPIO_BIAS_NP 5 + +/* GPIO registers */ +#define SSBI_REG_ADDR_GPIO_BASE 0x150 +#define SSBI_REG_ADDR_GPIO(n) (SSBI_REG_ADDR_GPIO_BASE + n) + +#define PM8XXX_BANK_WRITE BIT(7) + +#define PM8XXX_MAX_GPIOS 44 + +/* custom pinconf parameters */ +#define PM8XXX_QCOM_DRIVE_STRENGH (PIN_CONFIG_END + 1) +#define PM8XXX_QCOM_PULL_UP_STRENGTH (PIN_CONFIG_END + 2) + +/** + * struct pm8xxx_pin_data - dynamic configuration for a pin + * @reg: address of the control register + * @irq: IRQ from the PMIC interrupt controller + * @power_source: logical selected voltage source, mapping in static data + * is used translate to register values + * @mode: operating mode for the pin (input/output) + * @open_drain: output buffer configured as open-drain (vs push-pull) + * @output_value: configured output value + * @bias: register view of configured bias + * @pull_up_strength: placeholder for selected pull up strength + * only used to configure bias when pull up is selected + * @output_strength: selector of output-strength + * @disable: pin disabled / configured as tristate + * @function: pinmux selector + * @inverted: pin logic is inverted + */ +struct pm8xxx_pin_data { + unsigned reg; + int irq; + u8 power_source; + u8 mode; + bool open_drain; + bool output_value; + u8 bias; + u8 pull_up_strength; + u8 output_strength; + bool disable; + u8 function; + bool inverted; +}; + +struct pm8xxx_gpio { + struct device *dev; + struct regmap *regmap; + struct pinctrl_dev *pctrl; + struct gpio_chip chip; + + struct pinctrl_desc desc; + unsigned npins; +}; + +static const struct pinconf_generic_params pm8xxx_gpio_bindings[] = { + {"qcom,drive-strength", PM8XXX_QCOM_DRIVE_STRENGH, 0}, + {"qcom,pull-up-strength", PM8XXX_QCOM_PULL_UP_STRENGTH, 0}, +}; + +#ifdef CONFIG_DEBUG_FS +static const struct pin_config_item pm8xxx_conf_items[ARRAY_SIZE(pm8xxx_gpio_bindings)] = { + PCONFDUMP(PM8XXX_QCOM_DRIVE_STRENGH, "drive-strength", NULL, true), + PCONFDUMP(PM8XXX_QCOM_PULL_UP_STRENGTH, "pull up strength", NULL, true), +}; +#endif + +static const char * const pm8xxx_groups[PM8XXX_MAX_GPIOS] = { + "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", "gpio8", + "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", "gpio15", + "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21", "gpio22", + "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28", "gpio29", + "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35", "gpio36", + "gpio37", "gpio38", "gpio39", "gpio40", "gpio41", "gpio42", "gpio43", + "gpio44", +}; + +static const char * const pm8xxx_gpio_functions[] = { + PMIC_GPIO_FUNC_NORMAL, PMIC_GPIO_FUNC_PAIRED, + PMIC_GPIO_FUNC_FUNC1, PMIC_GPIO_FUNC_FUNC2, + PMIC_GPIO_FUNC_DTEST1, PMIC_GPIO_FUNC_DTEST2, + PMIC_GPIO_FUNC_DTEST3, PMIC_GPIO_FUNC_DTEST4, +}; + +static int pm8xxx_read_bank(struct pm8xxx_gpio *pctrl, + struct pm8xxx_pin_data *pin, int bank) +{ + unsigned int val = bank << 4; + int ret; + + ret = regmap_write(pctrl->regmap, pin->reg, val); + if (ret) { + dev_err(pctrl->dev, "failed to select bank %d\n", bank); + return ret; + } + + ret = regmap_read(pctrl->regmap, pin->reg, &val); + if (ret) { + dev_err(pctrl->dev, "failed to read register %d\n", bank); + return ret; + } + + return val; +} + +static int pm8xxx_write_bank(struct pm8xxx_gpio *pctrl, + struct pm8xxx_pin_data *pin, + int bank, + u8 val) +{ + int ret; + + val |= PM8XXX_BANK_WRITE; + val |= bank << 4; + + ret = regmap_write(pctrl->regmap, pin->reg, val); + if (ret) + dev_err(pctrl->dev, "failed to write register\n"); + + return ret; +} + +static int pm8xxx_get_groups_count(struct pinctrl_dev *pctldev) +{ + struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev); + + return pctrl->npins; +} + +static const char *pm8xxx_get_group_name(struct pinctrl_dev *pctldev, + unsigned group) +{ + return pm8xxx_groups[group]; +} + + +static int pm8xxx_get_group_pins(struct pinctrl_dev *pctldev, + unsigned group, + const unsigned **pins, + unsigned *num_pins) +{ + struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev); + + *pins = &pctrl->desc.pins[group].number; + *num_pins = 1; + + return 0; +} + +static const struct pinctrl_ops pm8xxx_pinctrl_ops = { + .get_groups_count = pm8xxx_get_groups_count, + .get_group_name = pm8xxx_get_group_name, + .get_group_pins = pm8xxx_get_group_pins, + .dt_node_to_map = pinconf_generic_dt_node_to_map_group, + .dt_free_map = pinctrl_utils_dt_free_map, +}; + +static int pm8xxx_get_functions_count(struct pinctrl_dev *pctldev) +{ + return ARRAY_SIZE(pm8xxx_gpio_functions); +} + +static const char *pm8xxx_get_function_name(struct pinctrl_dev *pctldev, + unsigned function) +{ + return pm8xxx_gpio_functions[function]; +} + +static int pm8xxx_get_function_groups(struct pinctrl_dev *pctldev, + unsigned function, + const char * const **groups, + unsigned * const num_groups) +{ + struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev); + + *groups = pm8xxx_groups; + *num_groups = pctrl->npins; + return 0; +} + +static int pm8xxx_pinmux_set_mux(struct pinctrl_dev *pctldev, + unsigned function, + unsigned group) +{ + struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev); + struct pm8xxx_pin_data *pin = pctrl->desc.pins[group].drv_data; + u8 val; + + pin->function = function; + val = pin->function << 1; + + pm8xxx_write_bank(pctrl, pin, 4, val); + + return 0; +} + +static const struct pinmux_ops pm8xxx_pinmux_ops = { + .get_functions_count = pm8xxx_get_functions_count, + .get_function_name = pm8xxx_get_function_name, + .get_function_groups = pm8xxx_get_function_groups, + .set_mux = pm8xxx_pinmux_set_mux, +}; + +static int pm8xxx_pin_config_get(struct pinctrl_dev *pctldev, + unsigned int offset, + unsigned long *config) +{ + struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev); + struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data; + unsigned param = pinconf_to_config_param(*config); + unsigned arg; + + switch (param) { + case PIN_CONFIG_BIAS_DISABLE: + arg = pin->bias == PM8XXX_GPIO_BIAS_NP; + break; + case PIN_CONFIG_BIAS_PULL_DOWN: + arg = pin->bias == PM8XXX_GPIO_BIAS_PD; + break; + case PIN_CONFIG_BIAS_PULL_UP: + arg = pin->bias <= PM8XXX_GPIO_BIAS_PU_1P5_30; + break; + case PM8XXX_QCOM_PULL_UP_STRENGTH: + arg = pin->pull_up_strength; + break; + case PIN_CONFIG_BIAS_HIGH_IMPEDANCE: + arg = pin->disable; + break; + case PIN_CONFIG_INPUT_ENABLE: + arg = pin->mode == PM8XXX_GPIO_MODE_INPUT; + break; + case PIN_CONFIG_OUTPUT: + if (pin->mode & PM8XXX_GPIO_MODE_OUTPUT) + arg = pin->output_value; + else + arg = 0; + break; + case PIN_CONFIG_POWER_SOURCE: + arg = pin->power_source; + break; + case PM8XXX_QCOM_DRIVE_STRENGH: + arg = pin->output_strength; + break; + case PIN_CONFIG_DRIVE_PUSH_PULL: + arg = !pin->open_drain; + break; + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + arg = pin->open_drain; + break; + default: + return -EINVAL; + } + + *config = pinconf_to_config_packed(param, arg); + + return 0; +} + +static int pm8xxx_pin_config_set(struct pinctrl_dev *pctldev, + unsigned int offset, + unsigned long *configs, + unsigned num_configs) +{ + struct pm8xxx_gpio *pctrl = pinctrl_dev_get_drvdata(pctldev); + struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data; + unsigned param; + unsigned arg; + unsigned i; + u8 banks = 0; + u8 val; + + for (i = 0; i < num_configs; i++) { + param = pinconf_to_config_param(configs[i]); + arg = pinconf_to_config_argument(configs[i]); + + switch (param) { + case PIN_CONFIG_BIAS_DISABLE: + pin->bias = PM8XXX_GPIO_BIAS_NP; + banks |= BIT(2); + pin->disable = 0; + banks |= BIT(3); + break; + case PIN_CONFIG_BIAS_PULL_DOWN: + pin->bias = PM8XXX_GPIO_BIAS_PD; + banks |= BIT(2); + pin->disable = 0; + banks |= BIT(3); + break; + case PM8XXX_QCOM_PULL_UP_STRENGTH: + if (arg > PM8XXX_GPIO_BIAS_PU_1P5_30) { + dev_err(pctrl->dev, "invalid pull-up strength\n"); + return -EINVAL; + } + pin->pull_up_strength = arg; + /* FALLTHROUGH */ + case PIN_CONFIG_BIAS_PULL_UP: + pin->bias = pin->pull_up_strength; + banks |= BIT(2); + pin->disable = 0; + banks |= BIT(3); + break; + case PIN_CONFIG_BIAS_HIGH_IMPEDANCE: + pin->disable = 1; + banks |= BIT(3); + break; + case PIN_CONFIG_INPUT_ENABLE: + pin->mode = PM8XXX_GPIO_MODE_INPUT; + banks |= BIT(0) | BIT(1); + break; + case PIN_CONFIG_OUTPUT: + pin->mode = PM8XXX_GPIO_MODE_OUTPUT; + pin->output_value = !!arg; + banks |= BIT(0) | BIT(1); + break; + case PIN_CONFIG_POWER_SOURCE: + pin->power_source = arg; + banks |= BIT(0); + break; + case PM8XXX_QCOM_DRIVE_STRENGH: + if (arg > PMIC_GPIO_STRENGTH_LOW) { + dev_err(pctrl->dev, "invalid drive strength\n"); + return -EINVAL; + } + pin->output_strength = arg; + banks |= BIT(3); + break; + case PIN_CONFIG_DRIVE_PUSH_PULL: + pin->open_drain = 0; + banks |= BIT(1); + break; + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + pin->open_drain = 1; + banks |= BIT(1); + break; + default: + dev_err(pctrl->dev, + "unsupported config parameter: %x\n", + param); + return -EINVAL; + } + } + + if (banks & BIT(0)) { + val = pin->power_source << 1; + val |= PM8XXX_GPIO_MODE_ENABLED; + pm8xxx_write_bank(pctrl, pin, 0, val); + } + + if (banks & BIT(1)) { + val = pin->mode << 2; + val |= pin->open_drain << 1; + val |= pin->output_value; + pm8xxx_write_bank(pctrl, pin, 1, val); + } + + if (banks & BIT(2)) { + val = pin->bias << 1; + pm8xxx_write_bank(pctrl, pin, 2, val); + } + + if (banks & BIT(3)) { + val = pin->output_strength << 2; + val |= pin->disable; + pm8xxx_write_bank(pctrl, pin, 3, val); + } + + if (banks & BIT(4)) { + val = pin->function << 1; + pm8xxx_write_bank(pctrl, pin, 4, val); + } + + if (banks & BIT(5)) { + val = 0; + if (!pin->inverted) + val |= BIT(3); + pm8xxx_write_bank(pctrl, pin, 5, val); + } + + return 0; +} + +static const struct pinconf_ops pm8xxx_pinconf_ops = { + .is_generic = true, + .pin_config_group_get = pm8xxx_pin_config_get, + .pin_config_group_set = pm8xxx_pin_config_set, +}; + +static struct pinctrl_desc pm8xxx_pinctrl_desc = { + .name = "pm8xxx_gpio", + .pctlops = &pm8xxx_pinctrl_ops, + .pmxops = &pm8xxx_pinmux_ops, + .confops = &pm8xxx_pinconf_ops, + .owner = THIS_MODULE, +}; + +static int pm8xxx_gpio_direction_input(struct gpio_chip *chip, + unsigned offset) +{ + struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip); + struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data; + u8 val; + + pin->mode = PM8XXX_GPIO_MODE_INPUT; + val = pin->mode << 2; + + pm8xxx_write_bank(pctrl, pin, 1, val); + + return 0; +} + +static int pm8xxx_gpio_direction_output(struct gpio_chip *chip, + unsigned offset, + int value) +{ + struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip); + struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data; + u8 val; + + pin->mode = PM8XXX_GPIO_MODE_OUTPUT; + pin->output_value = !!value; + + val = pin->mode << 2; + val |= pin->open_drain << 1; + val |= pin->output_value; + + pm8xxx_write_bank(pctrl, pin, 1, val); + + return 0; +} + +static int pm8xxx_gpio_get(struct gpio_chip *chip, unsigned offset) +{ + struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip); + struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data; + bool state; + int ret; + + if (pin->mode == PM8XXX_GPIO_MODE_OUTPUT) { + ret = pin->output_value; + } else { + ret = irq_get_irqchip_state(pin->irq, IRQCHIP_STATE_LINE_LEVEL, &state); + if (!ret) + ret = !!state; + } + + return ret; +} + +static void pm8xxx_gpio_set(struct gpio_chip *chip, unsigned offset, int value) +{ + struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip); + struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data; + u8 val; + + pin->output_value = !!value; + + val = pin->mode << 2; + val |= pin->open_drain << 1; + val |= pin->output_value; + + pm8xxx_write_bank(pctrl, pin, 1, val); +} + +static int pm8xxx_gpio_of_xlate(struct gpio_chip *chip, + const struct of_phandle_args *gpio_desc, + u32 *flags) +{ + if (chip->of_gpio_n_cells < 2) + return -EINVAL; + + if (flags) + *flags = gpio_desc->args[1]; + + return gpio_desc->args[0] - 1; +} + + +static int pm8xxx_gpio_to_irq(struct gpio_chip *chip, unsigned offset) +{ + struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip); + struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data; + + return pin->irq; +} + +#ifdef CONFIG_DEBUG_FS +#include <linux/seq_file.h> + +static void pm8xxx_gpio_dbg_show_one(struct seq_file *s, + struct pinctrl_dev *pctldev, + struct gpio_chip *chip, + unsigned offset, + unsigned gpio) +{ + struct pm8xxx_gpio *pctrl = container_of(chip, struct pm8xxx_gpio, chip); + struct pm8xxx_pin_data *pin = pctrl->desc.pins[offset].drv_data; + + static const char * const modes[] = { + "in", "both", "out", "off" + }; + static const char * const biases[] = { + "pull-up 30uA", "pull-up 1.5uA", "pull-up 31.5uA", + "pull-up 1.5uA + 30uA boost", "pull-down 10uA", "no pull" + }; + static const char * const buffer_types[] = { + "push-pull", "open-drain" + }; + static const char * const strengths[] = { + "no", "high", "medium", "low" + }; + + seq_printf(s, " gpio%-2d:", offset + 1); + if (pin->disable) { + seq_puts(s, " ---"); + } else { + seq_printf(s, " %-4s", modes[pin->mode]); + seq_printf(s, " %-7s", pm8xxx_gpio_functions[pin->function]); + seq_printf(s, " VIN%d", pin->power_source); + seq_printf(s, " %-27s", biases[pin->bias]); + seq_printf(s, " %-10s", buffer_types[pin->open_drain]); + seq_printf(s, " %-4s", pin->output_value ? "high" : "low"); + seq_printf(s, " %-7s", strengths[pin->output_strength]); + if (pin->inverted) + seq_puts(s, " inverted"); + } +} + +static void pm8xxx_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip) +{ + unsigned gpio = chip->base; + unsigned i; + + for (i = 0; i < chip->ngpio; i++, gpio++) { + pm8xxx_gpio_dbg_show_one(s, NULL, chip, i, gpio); + seq_puts(s, "\n"); + } +} + +#else +#define pm8xxx_gpio_dbg_show NULL +#endif + +static struct gpio_chip pm8xxx_gpio_template = { + .direction_input = pm8xxx_gpio_direction_input, + .direction_output = pm8xxx_gpio_direction_output, + .get = pm8xxx_gpio_get, + .set = pm8xxx_gpio_set, + .of_xlate = pm8xxx_gpio_of_xlate, + .to_irq = pm8xxx_gpio_to_irq, + .dbg_show = pm8xxx_gpio_dbg_show, + .owner = THIS_MODULE, +}; + +static int pm8xxx_pin_populate(struct pm8xxx_gpio *pctrl, + struct pm8xxx_pin_data *pin) +{ + int val; + + val = pm8xxx_read_bank(pctrl, pin, 0); + if (val < 0) + return val; + + pin->power_source = (val >> 1) & 0x7; + + val = pm8xxx_read_bank(pctrl, pin, 1); + if (val < 0) + return val; + + pin->mode = (val >> 2) & 0x3; + pin->open_drain = !!(val & BIT(1)); + pin->output_value = val & BIT(0); + + val = pm8xxx_read_bank(pctrl, pin, 2); + if (val < 0) + return val; + + pin->bias = (val >> 1) & 0x7; + if (pin->bias <= PM8XXX_GPIO_BIAS_PU_1P5_30) + pin->pull_up_strength = pin->bias; + else + pin->pull_up_strength = PM8XXX_GPIO_BIAS_PU_30; + + val = pm8xxx_read_bank(pctrl, pin, 3); + if (val < 0) + return val; + + pin->output_strength = (val >> 2) & 0x3; + pin->disable = val & BIT(0); + + val = pm8xxx_read_bank(pctrl, pin, 4); + if (val < 0) + return val; + + pin->function = (val >> 1) & 0x7; + + val = pm8xxx_read_bank(pctrl, pin, 5); + if (val < 0) + return val; + + pin->inverted = !(val & BIT(3)); + + return 0; +} + +static const struct of_device_id pm8xxx_gpio_of_match[] = { + { .compatible = "qcom,pm8018-gpio", .data = (void *)6 }, + { .compatible = "qcom,pm8038-gpio", .data = (void *)12 }, + { .compatible = "qcom,pm8058-gpio", .data = (void *)40 }, + { .compatible = "qcom,pm8917-gpio", .data = (void *)38 }, + { .compatible = "qcom,pm8921-gpio", .data = (void *)44 }, + { }, +}; +MODULE_DEVICE_TABLE(of, pm8xxx_gpio_of_match); + +static int pm8xxx_gpio_probe(struct platform_device *pdev) +{ + struct pm8xxx_pin_data *pin_data; + struct pinctrl_pin_desc *pins; + struct pm8xxx_gpio *pctrl; + int ret; + int i; + + pctrl = devm_kzalloc(&pdev->dev, sizeof(*pctrl), GFP_KERNEL); + if (!pctrl) + return -ENOMEM; + + pctrl->dev = &pdev->dev; + pctrl->npins = (unsigned long)of_device_get_match_data(&pdev->dev); + + pctrl->regmap = dev_get_regmap(pdev->dev.parent, NULL); + if (!pctrl->regmap) { + dev_err(&pdev->dev, "parent regmap unavailable\n"); + return -ENXIO; + } + + pctrl->desc = pm8xxx_pinctrl_desc; + pctrl->desc.npins = pctrl->npins; + + pins = devm_kcalloc(&pdev->dev, + pctrl->desc.npins, + sizeof(struct pinctrl_pin_desc), + GFP_KERNEL); + if (!pins) + return -ENOMEM; + + pin_data = devm_kcalloc(&pdev->dev, + pctrl->desc.npins, + sizeof(struct pm8xxx_pin_data), + GFP_KERNEL); + if (!pin_data) + return -ENOMEM; + + for (i = 0; i < pctrl->desc.npins; i++) { + pin_data[i].reg = SSBI_REG_ADDR_GPIO(i); + pin_data[i].irq = platform_get_irq(pdev, i); + if (pin_data[i].irq < 0) { + dev_err(&pdev->dev, + "missing interrupts for pin %d\n", i); + return pin_data[i].irq; + } + + ret = pm8xxx_pin_populate(pctrl, &pin_data[i]); + if (ret) + return ret; + + pins[i].number = i; + pins[i].name = pm8xxx_groups[i]; + pins[i].drv_data = &pin_data[i]; + } + pctrl->desc.pins = pins; + + pctrl->desc.num_custom_params = ARRAY_SIZE(pm8xxx_gpio_bindings); + pctrl->desc.custom_params = pm8xxx_gpio_bindings; +#ifdef CONFIG_DEBUG_FS + pctrl->desc.custom_conf_items = pm8xxx_conf_items; +#endif + + pctrl->pctrl = pinctrl_register(&pctrl->desc, &pdev->dev, pctrl); + if (IS_ERR(pctrl->pctrl)) { + dev_err(&pdev->dev, "couldn't register pm8xxx gpio driver\n"); + return PTR_ERR(pctrl->pctrl); + } + + pctrl->chip = pm8xxx_gpio_template; + pctrl->chip.base = -1; + pctrl->chip.dev = &pdev->dev; + pctrl->chip.of_node = pdev->dev.of_node; + pctrl->chip.of_gpio_n_cells = 2; + pctrl->chip.label = dev_name(pctrl->dev); + pctrl->chip.ngpio = pctrl->npins; + ret = gpiochip_add(&pctrl->chip); + if (ret) { + dev_err(&pdev->dev, "failed register gpiochip\n"); + goto unregister_pinctrl; + } + + ret = gpiochip_add_pin_range(&pctrl->chip, + dev_name(pctrl->dev), + 0, 0, pctrl->chip.ngpio); + if (ret) { + dev_err(pctrl->dev, "failed to add pin range\n"); + goto unregister_gpiochip; + } + + platform_set_drvdata(pdev, pctrl); + + dev_dbg(&pdev->dev, "Qualcomm pm8xxx gpio driver probed\n"); + + return 0; + +unregister_gpiochip: + gpiochip_remove(&pctrl->chip); + +unregister_pinctrl: + pinctrl_unregister(pctrl->pctrl); + + return ret; +} + +static int pm8xxx_gpio_remove(struct platform_device *pdev) +{ + struct pm8xxx_gpio *pctrl = platform_get_drvdata(pdev); + + gpiochip_remove(&pctrl->chip); + + pinctrl_unregister(pctrl->pctrl); + + return 0; +} + +static struct platform_driver pm8xxx_gpio_driver = { + .driver = { + .name = "qcom-ssbi-gpio", + .of_match_table = pm8xxx_gpio_of_match, + }, + .probe = pm8xxx_gpio_probe, + .remove = pm8xxx_gpio_remove, +}; + +module_platform_driver(pm8xxx_gpio_driver); + +MODULE_AUTHOR("Bjorn Andersson <bjorn.andersson@sonymobile.com>"); +MODULE_DESCRIPTION("Qualcomm PM8xxx GPIO driver"); +MODULE_LICENSE("GPL v2"); |