summaryrefslogtreecommitdiffstats
path: root/kernel/drivers/misc/eeprom
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/drivers/misc/eeprom')
-rw-r--r--kernel/drivers/misc/eeprom/Kconfig112
-rw-r--r--kernel/drivers/misc/eeprom/Makefile8
-rw-r--r--kernel/drivers/misc/eeprom/at24.c719
-rw-r--r--kernel/drivers/misc/eeprom/at25.c477
-rw-r--r--kernel/drivers/misc/eeprom/digsy_mtc_eeprom.c85
-rw-r--r--kernel/drivers/misc/eeprom/eeprom.c226
-rw-r--r--kernel/drivers/misc/eeprom/eeprom_93cx6.c381
-rw-r--r--kernel/drivers/misc/eeprom/eeprom_93xx46.c398
-rw-r--r--kernel/drivers/misc/eeprom/max6875.c214
-rw-r--r--kernel/drivers/misc/eeprom/sunxi_sid.c156
10 files changed, 2776 insertions, 0 deletions
diff --git a/kernel/drivers/misc/eeprom/Kconfig b/kernel/drivers/misc/eeprom/Kconfig
new file mode 100644
index 000000000..9536852fd
--- /dev/null
+++ b/kernel/drivers/misc/eeprom/Kconfig
@@ -0,0 +1,112 @@
+menu "EEPROM support"
+
+config EEPROM_AT24
+ tristate "I2C EEPROMs / RAMs / ROMs from most vendors"
+ depends on I2C && SYSFS
+ help
+ Enable this driver to get read/write support to most I2C EEPROMs
+ and compatible devices like FRAMs, SRAMs, ROMs etc. After you
+ configure the driver to know about each chip on your target
+ board. Use these generic chip names, instead of vendor-specific
+ ones like at24c64, 24lc02 or fm24c04:
+
+ 24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
+ 24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
+
+ Unless you like data loss puzzles, always be sure that any chip
+ you configure as a 24c32 (32 kbit) or larger is NOT really a
+ 24c16 (16 kbit) or smaller, and vice versa. Marking the chip
+ as read-only won't help recover from this. Also, if your chip
+ has any software write-protect mechanism you may want to review the
+ code to make sure this driver won't turn it on by accident.
+
+ If you use this with an SMBus adapter instead of an I2C adapter,
+ full functionality is not available. Only smaller devices are
+ supported (24c16 and below, max 4 kByte).
+
+ This driver can also be built as a module. If so, the module
+ will be called at24.
+
+config EEPROM_AT25
+ tristate "SPI EEPROMs from most vendors"
+ depends on SPI && SYSFS
+ help
+ Enable this driver to get read/write support to most SPI EEPROMs,
+ after you configure the board init code to know about each eeprom
+ on your target board.
+
+ This driver can also be built as a module. If so, the module
+ will be called at25.
+
+config EEPROM_LEGACY
+ tristate "Old I2C EEPROM reader"
+ depends on I2C && SYSFS
+ help
+ If you say yes here you get read-only access to the EEPROM data
+ available on modern memory DIMMs and Sony Vaio laptops via I2C. Such
+ EEPROMs could theoretically be available on other devices as well.
+
+ This driver can also be built as a module. If so, the module
+ will be called eeprom.
+
+config EEPROM_MAX6875
+ tristate "Maxim MAX6874/5 power supply supervisor"
+ depends on I2C
+ help
+ If you say yes here you get read-only support for the user EEPROM of
+ the Maxim MAX6874/5 EEPROM-programmable, quad power-supply
+ sequencer/supervisor.
+
+ All other features of this chip should be accessed via i2c-dev.
+
+ This driver can also be built as a module. If so, the module
+ will be called max6875.
+
+
+config EEPROM_93CX6
+ tristate "EEPROM 93CX6 support"
+ help
+ This is a driver for the EEPROM chipsets 93c46 and 93c66.
+ The driver supports both read as well as write commands.
+
+ If unsure, say N.
+
+config EEPROM_93XX46
+ tristate "Microwire EEPROM 93XX46 support"
+ depends on SPI && SYSFS
+ help
+ Driver for the microwire EEPROM chipsets 93xx46x. The driver
+ supports both read and write commands and also the command to
+ erase the whole EEPROM.
+
+ This driver can also be built as a module. If so, the module
+ will be called eeprom_93xx46.
+
+ If unsure, say N.
+
+config EEPROM_DIGSY_MTC_CFG
+ bool "DigsyMTC display configuration EEPROMs device"
+ depends on GPIO_MPC5200 && SPI_GPIO
+ help
+ This option enables access to display configuration EEPROMs
+ on digsy_mtc board. You have to additionally select Microwire
+ EEPROM 93XX46 driver. sysfs entries will be created for that
+ EEPROM allowing to read/write the configuration data or to
+ erase the whole EEPROM.
+
+ If unsure, say N.
+
+config EEPROM_SUNXI_SID
+ tristate "Allwinner sunxi security ID support"
+ depends on ARCH_SUNXI && SYSFS
+ help
+ This is a driver for the 'security ID' available on various Allwinner
+ devices.
+
+ Due to the potential risks involved with changing e-fuses,
+ this driver is read-only.
+
+ This driver can also be built as a module. If so, the module
+ will be called sunxi_sid.
+
+endmenu
diff --git a/kernel/drivers/misc/eeprom/Makefile b/kernel/drivers/misc/eeprom/Makefile
new file mode 100644
index 000000000..9507aec95
--- /dev/null
+++ b/kernel/drivers/misc/eeprom/Makefile
@@ -0,0 +1,8 @@
+obj-$(CONFIG_EEPROM_AT24) += at24.o
+obj-$(CONFIG_EEPROM_AT25) += at25.o
+obj-$(CONFIG_EEPROM_LEGACY) += eeprom.o
+obj-$(CONFIG_EEPROM_MAX6875) += max6875.o
+obj-$(CONFIG_EEPROM_93CX6) += eeprom_93cx6.o
+obj-$(CONFIG_EEPROM_93XX46) += eeprom_93xx46.o
+obj-$(CONFIG_EEPROM_SUNXI_SID) += sunxi_sid.o
+obj-$(CONFIG_EEPROM_DIGSY_MTC_CFG) += digsy_mtc_eeprom.o
diff --git a/kernel/drivers/misc/eeprom/at24.c b/kernel/drivers/misc/eeprom/at24.c
new file mode 100644
index 000000000..2d3db81be
--- /dev/null
+++ b/kernel/drivers/misc/eeprom/at24.c
@@ -0,0 +1,719 @@
+/*
+ * at24.c - handle most I2C EEPROMs
+ *
+ * Copyright (C) 2005-2007 David Brownell
+ * Copyright (C) 2008 Wolfram Sang, Pengutronix
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/mutex.h>
+#include <linux/sysfs.h>
+#include <linux/mod_devicetable.h>
+#include <linux/log2.h>
+#include <linux/bitops.h>
+#include <linux/jiffies.h>
+#include <linux/of.h>
+#include <linux/i2c.h>
+#include <linux/platform_data/at24.h>
+
+/*
+ * I2C EEPROMs from most vendors are inexpensive and mostly interchangeable.
+ * Differences between different vendor product lines (like Atmel AT24C or
+ * MicroChip 24LC, etc) won't much matter for typical read/write access.
+ * There are also I2C RAM chips, likewise interchangeable. One example
+ * would be the PCF8570, which acts like a 24c02 EEPROM (256 bytes).
+ *
+ * However, misconfiguration can lose data. "Set 16-bit memory address"
+ * to a part with 8-bit addressing will overwrite data. Writing with too
+ * big a page size also loses data. And it's not safe to assume that the
+ * conventional addresses 0x50..0x57 only hold eeproms; a PCF8563 RTC
+ * uses 0x51, for just one example.
+ *
+ * Accordingly, explicit board-specific configuration data should be used
+ * in almost all cases. (One partial exception is an SMBus used to access
+ * "SPD" data for DRAM sticks. Those only use 24c02 EEPROMs.)
+ *
+ * So this driver uses "new style" I2C driver binding, expecting to be
+ * told what devices exist. That may be in arch/X/mach-Y/board-Z.c or
+ * similar kernel-resident tables; or, configuration data coming from
+ * a bootloader.
+ *
+ * Other than binding model, current differences from "eeprom" driver are
+ * that this one handles write access and isn't restricted to 24c02 devices.
+ * It also handles larger devices (32 kbit and up) with two-byte addresses,
+ * which won't work on pure SMBus systems.
+ */
+
+struct at24_data {
+ struct at24_platform_data chip;
+ struct memory_accessor macc;
+ int use_smbus;
+ int use_smbus_write;
+
+ /*
+ * Lock protects against activities from other Linux tasks,
+ * but not from changes by other I2C masters.
+ */
+ struct mutex lock;
+ struct bin_attribute bin;
+
+ u8 *writebuf;
+ unsigned write_max;
+ unsigned num_addresses;
+
+ /*
+ * Some chips tie up multiple I2C addresses; dummy devices reserve
+ * them for us, and we'll use them with SMBus calls.
+ */
+ struct i2c_client *client[];
+};
+
+/*
+ * This parameter is to help this driver avoid blocking other drivers out
+ * of I2C for potentially troublesome amounts of time. With a 100 kHz I2C
+ * clock, one 256 byte read takes about 1/43 second which is excessive;
+ * but the 1/170 second it takes at 400 kHz may be quite reasonable; and
+ * at 1 MHz (Fm+) a 1/430 second delay could easily be invisible.
+ *
+ * This value is forced to be a power of two so that writes align on pages.
+ */
+static unsigned io_limit = 128;
+module_param(io_limit, uint, 0);
+MODULE_PARM_DESC(io_limit, "Maximum bytes per I/O (default 128)");
+
+/*
+ * Specs often allow 5 msec for a page write, sometimes 20 msec;
+ * it's important to recover from write timeouts.
+ */
+static unsigned write_timeout = 25;
+module_param(write_timeout, uint, 0);
+MODULE_PARM_DESC(write_timeout, "Time (in ms) to try writes (default 25)");
+
+#define AT24_SIZE_BYTELEN 5
+#define AT24_SIZE_FLAGS 8
+
+#define AT24_BITMASK(x) (BIT(x) - 1)
+
+/* create non-zero magic value for given eeprom parameters */
+#define AT24_DEVICE_MAGIC(_len, _flags) \
+ ((1 << AT24_SIZE_FLAGS | (_flags)) \
+ << AT24_SIZE_BYTELEN | ilog2(_len))
+
+static const struct i2c_device_id at24_ids[] = {
+ /* needs 8 addresses as A0-A2 are ignored */
+ { "24c00", AT24_DEVICE_MAGIC(128 / 8, AT24_FLAG_TAKE8ADDR) },
+ /* old variants can't be handled with this generic entry! */
+ { "24c01", AT24_DEVICE_MAGIC(1024 / 8, 0) },
+ { "24c02", AT24_DEVICE_MAGIC(2048 / 8, 0) },
+ /* spd is a 24c02 in memory DIMMs */
+ { "spd", AT24_DEVICE_MAGIC(2048 / 8,
+ AT24_FLAG_READONLY | AT24_FLAG_IRUGO) },
+ { "24c04", AT24_DEVICE_MAGIC(4096 / 8, 0) },
+ /* 24rf08 quirk is handled at i2c-core */
+ { "24c08", AT24_DEVICE_MAGIC(8192 / 8, 0) },
+ { "24c16", AT24_DEVICE_MAGIC(16384 / 8, 0) },
+ { "24c32", AT24_DEVICE_MAGIC(32768 / 8, AT24_FLAG_ADDR16) },
+ { "24c64", AT24_DEVICE_MAGIC(65536 / 8, AT24_FLAG_ADDR16) },
+ { "24c128", AT24_DEVICE_MAGIC(131072 / 8, AT24_FLAG_ADDR16) },
+ { "24c256", AT24_DEVICE_MAGIC(262144 / 8, AT24_FLAG_ADDR16) },
+ { "24c512", AT24_DEVICE_MAGIC(524288 / 8, AT24_FLAG_ADDR16) },
+ { "24c1024", AT24_DEVICE_MAGIC(1048576 / 8, AT24_FLAG_ADDR16) },
+ { "at24", 0 },
+ { /* END OF LIST */ }
+};
+MODULE_DEVICE_TABLE(i2c, at24_ids);
+
+/*-------------------------------------------------------------------------*/
+
+/*
+ * This routine supports chips which consume multiple I2C addresses. It
+ * computes the addressing information to be used for a given r/w request.
+ * Assumes that sanity checks for offset happened at sysfs-layer.
+ */
+static struct i2c_client *at24_translate_offset(struct at24_data *at24,
+ unsigned *offset)
+{
+ unsigned i;
+
+ if (at24->chip.flags & AT24_FLAG_ADDR16) {
+ i = *offset >> 16;
+ *offset &= 0xffff;
+ } else {
+ i = *offset >> 8;
+ *offset &= 0xff;
+ }
+
+ return at24->client[i];
+}
+
+static ssize_t at24_eeprom_read(struct at24_data *at24, char *buf,
+ unsigned offset, size_t count)
+{
+ struct i2c_msg msg[2];
+ u8 msgbuf[2];
+ struct i2c_client *client;
+ unsigned long timeout, read_time;
+ int status, i;
+
+ memset(msg, 0, sizeof(msg));
+
+ /*
+ * REVISIT some multi-address chips don't rollover page reads to
+ * the next slave address, so we may need to truncate the count.
+ * Those chips might need another quirk flag.
+ *
+ * If the real hardware used four adjacent 24c02 chips and that
+ * were misconfigured as one 24c08, that would be a similar effect:
+ * one "eeprom" file not four, but larger reads would fail when
+ * they crossed certain pages.
+ */
+
+ /*
+ * Slave address and byte offset derive from the offset. Always
+ * set the byte address; on a multi-master board, another master
+ * may have changed the chip's "current" address pointer.
+ */
+ client = at24_translate_offset(at24, &offset);
+
+ if (count > io_limit)
+ count = io_limit;
+
+ switch (at24->use_smbus) {
+ case I2C_SMBUS_I2C_BLOCK_DATA:
+ /* Smaller eeproms can work given some SMBus extension calls */
+ if (count > I2C_SMBUS_BLOCK_MAX)
+ count = I2C_SMBUS_BLOCK_MAX;
+ break;
+ case I2C_SMBUS_WORD_DATA:
+ count = 2;
+ break;
+ case I2C_SMBUS_BYTE_DATA:
+ count = 1;
+ break;
+ default:
+ /*
+ * When we have a better choice than SMBus calls, use a
+ * combined I2C message. Write address; then read up to
+ * io_limit data bytes. Note that read page rollover helps us
+ * here (unlike writes). msgbuf is u8 and will cast to our
+ * needs.
+ */
+ i = 0;
+ if (at24->chip.flags & AT24_FLAG_ADDR16)
+ msgbuf[i++] = offset >> 8;
+ msgbuf[i++] = offset;
+
+ msg[0].addr = client->addr;
+ msg[0].buf = msgbuf;
+ msg[0].len = i;
+
+ msg[1].addr = client->addr;
+ msg[1].flags = I2C_M_RD;
+ msg[1].buf = buf;
+ msg[1].len = count;
+ }
+
+ /*
+ * Reads fail if the previous write didn't complete yet. We may
+ * loop a few times until this one succeeds, waiting at least
+ * long enough for one entire page write to work.
+ */
+ timeout = jiffies + msecs_to_jiffies(write_timeout);
+ do {
+ read_time = jiffies;
+ switch (at24->use_smbus) {
+ case I2C_SMBUS_I2C_BLOCK_DATA:
+ status = i2c_smbus_read_i2c_block_data(client, offset,
+ count, buf);
+ break;
+ case I2C_SMBUS_WORD_DATA:
+ status = i2c_smbus_read_word_data(client, offset);
+ if (status >= 0) {
+ buf[0] = status & 0xff;
+ buf[1] = status >> 8;
+ status = count;
+ }
+ break;
+ case I2C_SMBUS_BYTE_DATA:
+ status = i2c_smbus_read_byte_data(client, offset);
+ if (status >= 0) {
+ buf[0] = status;
+ status = count;
+ }
+ break;
+ default:
+ status = i2c_transfer(client->adapter, msg, 2);
+ if (status == 2)
+ status = count;
+ }
+ dev_dbg(&client->dev, "read %zu@%d --> %d (%ld)\n",
+ count, offset, status, jiffies);
+
+ if (status == count)
+ return count;
+
+ /* REVISIT: at HZ=100, this is sloooow */
+ msleep(1);
+ } while (time_before(read_time, timeout));
+
+ return -ETIMEDOUT;
+}
+
+static ssize_t at24_read(struct at24_data *at24,
+ char *buf, loff_t off, size_t count)
+{
+ ssize_t retval = 0;
+
+ if (unlikely(!count))
+ return count;
+
+ /*
+ * Read data from chip, protecting against concurrent updates
+ * from this host, but not from other I2C masters.
+ */
+ mutex_lock(&at24->lock);
+
+ while (count) {
+ ssize_t status;
+
+ status = at24_eeprom_read(at24, buf, off, count);
+ if (status <= 0) {
+ if (retval == 0)
+ retval = status;
+ break;
+ }
+ buf += status;
+ off += status;
+ count -= status;
+ retval += status;
+ }
+
+ mutex_unlock(&at24->lock);
+
+ return retval;
+}
+
+static ssize_t at24_bin_read(struct file *filp, struct kobject *kobj,
+ struct bin_attribute *attr,
+ char *buf, loff_t off, size_t count)
+{
+ struct at24_data *at24;
+
+ at24 = dev_get_drvdata(container_of(kobj, struct device, kobj));
+ return at24_read(at24, buf, off, count);
+}
+
+
+/*
+ * Note that if the hardware write-protect pin is pulled high, the whole
+ * chip is normally write protected. But there are plenty of product
+ * variants here, including OTP fuses and partial chip protect.
+ *
+ * We only use page mode writes; the alternative is sloooow. This routine
+ * writes at most one page.
+ */
+static ssize_t at24_eeprom_write(struct at24_data *at24, const char *buf,
+ unsigned offset, size_t count)
+{
+ struct i2c_client *client;
+ struct i2c_msg msg;
+ ssize_t status = 0;
+ unsigned long timeout, write_time;
+ unsigned next_page;
+
+ /* Get corresponding I2C address and adjust offset */
+ client = at24_translate_offset(at24, &offset);
+
+ /* write_max is at most a page */
+ if (count > at24->write_max)
+ count = at24->write_max;
+
+ /* Never roll over backwards, to the start of this page */
+ next_page = roundup(offset + 1, at24->chip.page_size);
+ if (offset + count > next_page)
+ count = next_page - offset;
+
+ /* If we'll use I2C calls for I/O, set up the message */
+ if (!at24->use_smbus) {
+ int i = 0;
+
+ msg.addr = client->addr;
+ msg.flags = 0;
+
+ /* msg.buf is u8 and casts will mask the values */
+ msg.buf = at24->writebuf;
+ if (at24->chip.flags & AT24_FLAG_ADDR16)
+ msg.buf[i++] = offset >> 8;
+
+ msg.buf[i++] = offset;
+ memcpy(&msg.buf[i], buf, count);
+ msg.len = i + count;
+ }
+
+ /*
+ * Writes fail if the previous one didn't complete yet. We may
+ * loop a few times until this one succeeds, waiting at least
+ * long enough for one entire page write to work.
+ */
+ timeout = jiffies + msecs_to_jiffies(write_timeout);
+ do {
+ write_time = jiffies;
+ if (at24->use_smbus_write) {
+ switch (at24->use_smbus_write) {
+ case I2C_SMBUS_I2C_BLOCK_DATA:
+ status = i2c_smbus_write_i2c_block_data(client,
+ offset, count, buf);
+ break;
+ case I2C_SMBUS_BYTE_DATA:
+ status = i2c_smbus_write_byte_data(client,
+ offset, buf[0]);
+ break;
+ }
+
+ if (status == 0)
+ status = count;
+ } else {
+ status = i2c_transfer(client->adapter, &msg, 1);
+ if (status == 1)
+ status = count;
+ }
+ dev_dbg(&client->dev, "write %zu@%d --> %zd (%ld)\n",
+ count, offset, status, jiffies);
+
+ if (status == count)
+ return count;
+
+ /* REVISIT: at HZ=100, this is sloooow */
+ msleep(1);
+ } while (time_before(write_time, timeout));
+
+ return -ETIMEDOUT;
+}
+
+static ssize_t at24_write(struct at24_data *at24, const char *buf, loff_t off,
+ size_t count)
+{
+ ssize_t retval = 0;
+
+ if (unlikely(!count))
+ return count;
+
+ /*
+ * Write data to chip, protecting against concurrent updates
+ * from this host, but not from other I2C masters.
+ */
+ mutex_lock(&at24->lock);
+
+ while (count) {
+ ssize_t status;
+
+ status = at24_eeprom_write(at24, buf, off, count);
+ if (status <= 0) {
+ if (retval == 0)
+ retval = status;
+ break;
+ }
+ buf += status;
+ off += status;
+ count -= status;
+ retval += status;
+ }
+
+ mutex_unlock(&at24->lock);
+
+ return retval;
+}
+
+static ssize_t at24_bin_write(struct file *filp, struct kobject *kobj,
+ struct bin_attribute *attr,
+ char *buf, loff_t off, size_t count)
+{
+ struct at24_data *at24;
+
+ if (unlikely(off >= attr->size))
+ return -EFBIG;
+
+ at24 = dev_get_drvdata(container_of(kobj, struct device, kobj));
+ return at24_write(at24, buf, off, count);
+}
+
+/*-------------------------------------------------------------------------*/
+
+/*
+ * This lets other kernel code access the eeprom data. For example, it
+ * might hold a board's Ethernet address, or board-specific calibration
+ * data generated on the manufacturing floor.
+ */
+
+static ssize_t at24_macc_read(struct memory_accessor *macc, char *buf,
+ off_t offset, size_t count)
+{
+ struct at24_data *at24 = container_of(macc, struct at24_data, macc);
+
+ return at24_read(at24, buf, offset, count);
+}
+
+static ssize_t at24_macc_write(struct memory_accessor *macc, const char *buf,
+ off_t offset, size_t count)
+{
+ struct at24_data *at24 = container_of(macc, struct at24_data, macc);
+
+ return at24_write(at24, buf, offset, count);
+}
+
+/*-------------------------------------------------------------------------*/
+
+#ifdef CONFIG_OF
+static void at24_get_ofdata(struct i2c_client *client,
+ struct at24_platform_data *chip)
+{
+ const __be32 *val;
+ struct device_node *node = client->dev.of_node;
+
+ if (node) {
+ if (of_get_property(node, "read-only", NULL))
+ chip->flags |= AT24_FLAG_READONLY;
+ val = of_get_property(node, "pagesize", NULL);
+ if (val)
+ chip->page_size = be32_to_cpup(val);
+ }
+}
+#else
+static void at24_get_ofdata(struct i2c_client *client,
+ struct at24_platform_data *chip)
+{ }
+#endif /* CONFIG_OF */
+
+static int at24_probe(struct i2c_client *client, const struct i2c_device_id *id)
+{
+ struct at24_platform_data chip;
+ bool writable;
+ int use_smbus = 0;
+ int use_smbus_write = 0;
+ struct at24_data *at24;
+ int err;
+ unsigned i, num_addresses;
+ kernel_ulong_t magic;
+
+ if (client->dev.platform_data) {
+ chip = *(struct at24_platform_data *)client->dev.platform_data;
+ } else {
+ if (!id->driver_data)
+ return -ENODEV;
+
+ magic = id->driver_data;
+ chip.byte_len = BIT(magic & AT24_BITMASK(AT24_SIZE_BYTELEN));
+ magic >>= AT24_SIZE_BYTELEN;
+ chip.flags = magic & AT24_BITMASK(AT24_SIZE_FLAGS);
+ /*
+ * This is slow, but we can't know all eeproms, so we better
+ * play safe. Specifying custom eeprom-types via platform_data
+ * is recommended anyhow.
+ */
+ chip.page_size = 1;
+
+ /* update chipdata if OF is present */
+ at24_get_ofdata(client, &chip);
+
+ chip.setup = NULL;
+ chip.context = NULL;
+ }
+
+ if (!is_power_of_2(chip.byte_len))
+ dev_warn(&client->dev,
+ "byte_len looks suspicious (no power of 2)!\n");
+ if (!chip.page_size) {
+ dev_err(&client->dev, "page_size must not be 0!\n");
+ return -EINVAL;
+ }
+ if (!is_power_of_2(chip.page_size))
+ dev_warn(&client->dev,
+ "page_size looks suspicious (no power of 2)!\n");
+
+ /* Use I2C operations unless we're stuck with SMBus extensions. */
+ if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+ if (chip.flags & AT24_FLAG_ADDR16)
+ return -EPFNOSUPPORT;
+
+ if (i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
+ use_smbus = I2C_SMBUS_I2C_BLOCK_DATA;
+ } else if (i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_READ_WORD_DATA)) {
+ use_smbus = I2C_SMBUS_WORD_DATA;
+ } else if (i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_READ_BYTE_DATA)) {
+ use_smbus = I2C_SMBUS_BYTE_DATA;
+ } else {
+ return -EPFNOSUPPORT;
+ }
+ }
+
+ /* Use I2C operations unless we're stuck with SMBus extensions. */
+ if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+ if (i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_WRITE_I2C_BLOCK)) {
+ use_smbus_write = I2C_SMBUS_I2C_BLOCK_DATA;
+ } else if (i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_WRITE_BYTE_DATA)) {
+ use_smbus_write = I2C_SMBUS_BYTE_DATA;
+ chip.page_size = 1;
+ }
+ }
+
+ if (chip.flags & AT24_FLAG_TAKE8ADDR)
+ num_addresses = 8;
+ else
+ num_addresses = DIV_ROUND_UP(chip.byte_len,
+ (chip.flags & AT24_FLAG_ADDR16) ? 65536 : 256);
+
+ at24 = devm_kzalloc(&client->dev, sizeof(struct at24_data) +
+ num_addresses * sizeof(struct i2c_client *), GFP_KERNEL);
+ if (!at24)
+ return -ENOMEM;
+
+ mutex_init(&at24->lock);
+ at24->use_smbus = use_smbus;
+ at24->use_smbus_write = use_smbus_write;
+ at24->chip = chip;
+ at24->num_addresses = num_addresses;
+
+ /*
+ * Export the EEPROM bytes through sysfs, since that's convenient.
+ * By default, only root should see the data (maybe passwords etc)
+ */
+ sysfs_bin_attr_init(&at24->bin);
+ at24->bin.attr.name = "eeprom";
+ at24->bin.attr.mode = chip.flags & AT24_FLAG_IRUGO ? S_IRUGO : S_IRUSR;
+ at24->bin.read = at24_bin_read;
+ at24->bin.size = chip.byte_len;
+
+ at24->macc.read = at24_macc_read;
+
+ writable = !(chip.flags & AT24_FLAG_READONLY);
+ if (writable) {
+ if (!use_smbus || use_smbus_write) {
+
+ unsigned write_max = chip.page_size;
+
+ at24->macc.write = at24_macc_write;
+
+ at24->bin.write = at24_bin_write;
+ at24->bin.attr.mode |= S_IWUSR;
+
+ if (write_max > io_limit)
+ write_max = io_limit;
+ if (use_smbus && write_max > I2C_SMBUS_BLOCK_MAX)
+ write_max = I2C_SMBUS_BLOCK_MAX;
+ at24->write_max = write_max;
+
+ /* buffer (data + address at the beginning) */
+ at24->writebuf = devm_kzalloc(&client->dev,
+ write_max + 2, GFP_KERNEL);
+ if (!at24->writebuf)
+ return -ENOMEM;
+ } else {
+ dev_warn(&client->dev,
+ "cannot write due to controller restrictions.");
+ }
+ }
+
+ at24->client[0] = client;
+
+ /* use dummy devices for multiple-address chips */
+ for (i = 1; i < num_addresses; i++) {
+ at24->client[i] = i2c_new_dummy(client->adapter,
+ client->addr + i);
+ if (!at24->client[i]) {
+ dev_err(&client->dev, "address 0x%02x unavailable\n",
+ client->addr + i);
+ err = -EADDRINUSE;
+ goto err_clients;
+ }
+ }
+
+ err = sysfs_create_bin_file(&client->dev.kobj, &at24->bin);
+ if (err)
+ goto err_clients;
+
+ i2c_set_clientdata(client, at24);
+
+ dev_info(&client->dev, "%zu byte %s EEPROM, %s, %u bytes/write\n",
+ at24->bin.size, client->name,
+ writable ? "writable" : "read-only", at24->write_max);
+ if (use_smbus == I2C_SMBUS_WORD_DATA ||
+ use_smbus == I2C_SMBUS_BYTE_DATA) {
+ dev_notice(&client->dev, "Falling back to %s reads, "
+ "performance will suffer\n", use_smbus ==
+ I2C_SMBUS_WORD_DATA ? "word" : "byte");
+ }
+
+ /* export data to kernel code */
+ if (chip.setup)
+ chip.setup(&at24->macc, chip.context);
+
+ return 0;
+
+err_clients:
+ for (i = 1; i < num_addresses; i++)
+ if (at24->client[i])
+ i2c_unregister_device(at24->client[i]);
+
+ return err;
+}
+
+static int at24_remove(struct i2c_client *client)
+{
+ struct at24_data *at24;
+ int i;
+
+ at24 = i2c_get_clientdata(client);
+ sysfs_remove_bin_file(&client->dev.kobj, &at24->bin);
+
+ for (i = 1; i < at24->num_addresses; i++)
+ i2c_unregister_device(at24->client[i]);
+
+ return 0;
+}
+
+/*-------------------------------------------------------------------------*/
+
+static struct i2c_driver at24_driver = {
+ .driver = {
+ .name = "at24",
+ .owner = THIS_MODULE,
+ },
+ .probe = at24_probe,
+ .remove = at24_remove,
+ .id_table = at24_ids,
+};
+
+static int __init at24_init(void)
+{
+ if (!io_limit) {
+ pr_err("at24: io_limit must not be 0!\n");
+ return -EINVAL;
+ }
+
+ io_limit = rounddown_pow_of_two(io_limit);
+ return i2c_add_driver(&at24_driver);
+}
+module_init(at24_init);
+
+static void __exit at24_exit(void)
+{
+ i2c_del_driver(&at24_driver);
+}
+module_exit(at24_exit);
+
+MODULE_DESCRIPTION("Driver for most I2C EEPROMs");
+MODULE_AUTHOR("David Brownell and Wolfram Sang");
+MODULE_LICENSE("GPL");
diff --git a/kernel/drivers/misc/eeprom/at25.c b/kernel/drivers/misc/eeprom/at25.c
new file mode 100644
index 000000000..0a1af93ec
--- /dev/null
+++ b/kernel/drivers/misc/eeprom/at25.c
@@ -0,0 +1,477 @@
+/*
+ * at25.c -- support most SPI EEPROMs, such as Atmel AT25 models
+ *
+ * Copyright (C) 2006 David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/sched.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/eeprom.h>
+#include <linux/property.h>
+
+/*
+ * NOTE: this is an *EEPROM* driver. The vagaries of product naming
+ * mean that some AT25 products are EEPROMs, and others are FLASH.
+ * Handle FLASH chips with the drivers/mtd/devices/m25p80.c driver,
+ * not this one!
+ */
+
+struct at25_data {
+ struct spi_device *spi;
+ struct memory_accessor mem;
+ struct mutex lock;
+ struct spi_eeprom chip;
+ struct bin_attribute bin;
+ unsigned addrlen;
+};
+
+#define AT25_WREN 0x06 /* latch the write enable */
+#define AT25_WRDI 0x04 /* reset the write enable */
+#define AT25_RDSR 0x05 /* read status register */
+#define AT25_WRSR 0x01 /* write status register */
+#define AT25_READ 0x03 /* read byte(s) */
+#define AT25_WRITE 0x02 /* write byte(s)/sector */
+
+#define AT25_SR_nRDY 0x01 /* nRDY = write-in-progress */
+#define AT25_SR_WEN 0x02 /* write enable (latched) */
+#define AT25_SR_BP0 0x04 /* BP for software writeprotect */
+#define AT25_SR_BP1 0x08
+#define AT25_SR_WPEN 0x80 /* writeprotect enable */
+
+#define AT25_INSTR_BIT3 0x08 /* Additional address bit in instr */
+
+#define EE_MAXADDRLEN 3 /* 24 bit addresses, up to 2 MBytes */
+
+/* Specs often allow 5 msec for a page write, sometimes 20 msec;
+ * it's important to recover from write timeouts.
+ */
+#define EE_TIMEOUT 25
+
+/*-------------------------------------------------------------------------*/
+
+#define io_limit PAGE_SIZE /* bytes */
+
+static ssize_t
+at25_ee_read(
+ struct at25_data *at25,
+ char *buf,
+ unsigned offset,
+ size_t count
+)
+{
+ u8 command[EE_MAXADDRLEN + 1];
+ u8 *cp;
+ ssize_t status;
+ struct spi_transfer t[2];
+ struct spi_message m;
+ u8 instr;
+
+ if (unlikely(offset >= at25->bin.size))
+ return 0;
+ if ((offset + count) > at25->bin.size)
+ count = at25->bin.size - offset;
+ if (unlikely(!count))
+ return count;
+
+ cp = command;
+
+ instr = AT25_READ;
+ if (at25->chip.flags & EE_INSTR_BIT3_IS_ADDR)
+ if (offset >= (1U << (at25->addrlen * 8)))
+ instr |= AT25_INSTR_BIT3;
+ *cp++ = instr;
+
+ /* 8/16/24-bit address is written MSB first */
+ switch (at25->addrlen) {
+ default: /* case 3 */
+ *cp++ = offset >> 16;
+ case 2:
+ *cp++ = offset >> 8;
+ case 1:
+ case 0: /* can't happen: for better codegen */
+ *cp++ = offset >> 0;
+ }
+
+ spi_message_init(&m);
+ memset(t, 0, sizeof t);
+
+ t[0].tx_buf = command;
+ t[0].len = at25->addrlen + 1;
+ spi_message_add_tail(&t[0], &m);
+
+ t[1].rx_buf = buf;
+ t[1].len = count;
+ spi_message_add_tail(&t[1], &m);
+
+ mutex_lock(&at25->lock);
+
+ /* Read it all at once.
+ *
+ * REVISIT that's potentially a problem with large chips, if
+ * other devices on the bus need to be accessed regularly or
+ * this chip is clocked very slowly
+ */
+ status = spi_sync(at25->spi, &m);
+ dev_dbg(&at25->spi->dev,
+ "read %Zd bytes at %d --> %d\n",
+ count, offset, (int) status);
+
+ mutex_unlock(&at25->lock);
+ return status ? status : count;
+}
+
+static ssize_t
+at25_bin_read(struct file *filp, struct kobject *kobj,
+ struct bin_attribute *bin_attr,
+ char *buf, loff_t off, size_t count)
+{
+ struct device *dev;
+ struct at25_data *at25;
+
+ dev = container_of(kobj, struct device, kobj);
+ at25 = dev_get_drvdata(dev);
+
+ return at25_ee_read(at25, buf, off, count);
+}
+
+
+static ssize_t
+at25_ee_write(struct at25_data *at25, const char *buf, loff_t off,
+ size_t count)
+{
+ ssize_t status = 0;
+ unsigned written = 0;
+ unsigned buf_size;
+ u8 *bounce;
+
+ if (unlikely(off >= at25->bin.size))
+ return -EFBIG;
+ if ((off + count) > at25->bin.size)
+ count = at25->bin.size - off;
+ if (unlikely(!count))
+ return count;
+
+ /* Temp buffer starts with command and address */
+ buf_size = at25->chip.page_size;
+ if (buf_size > io_limit)
+ buf_size = io_limit;
+ bounce = kmalloc(buf_size + at25->addrlen + 1, GFP_KERNEL);
+ if (!bounce)
+ return -ENOMEM;
+
+ /* For write, rollover is within the page ... so we write at
+ * most one page, then manually roll over to the next page.
+ */
+ mutex_lock(&at25->lock);
+ do {
+ unsigned long timeout, retries;
+ unsigned segment;
+ unsigned offset = (unsigned) off;
+ u8 *cp = bounce;
+ int sr;
+ u8 instr;
+
+ *cp = AT25_WREN;
+ status = spi_write(at25->spi, cp, 1);
+ if (status < 0) {
+ dev_dbg(&at25->spi->dev, "WREN --> %d\n",
+ (int) status);
+ break;
+ }
+
+ instr = AT25_WRITE;
+ if (at25->chip.flags & EE_INSTR_BIT3_IS_ADDR)
+ if (offset >= (1U << (at25->addrlen * 8)))
+ instr |= AT25_INSTR_BIT3;
+ *cp++ = instr;
+
+ /* 8/16/24-bit address is written MSB first */
+ switch (at25->addrlen) {
+ default: /* case 3 */
+ *cp++ = offset >> 16;
+ case 2:
+ *cp++ = offset >> 8;
+ case 1:
+ case 0: /* can't happen: for better codegen */
+ *cp++ = offset >> 0;
+ }
+
+ /* Write as much of a page as we can */
+ segment = buf_size - (offset % buf_size);
+ if (segment > count)
+ segment = count;
+ memcpy(cp, buf, segment);
+ status = spi_write(at25->spi, bounce,
+ segment + at25->addrlen + 1);
+ dev_dbg(&at25->spi->dev,
+ "write %u bytes at %u --> %d\n",
+ segment, offset, (int) status);
+ if (status < 0)
+ break;
+
+ /* REVISIT this should detect (or prevent) failed writes
+ * to readonly sections of the EEPROM...
+ */
+
+ /* Wait for non-busy status */
+ timeout = jiffies + msecs_to_jiffies(EE_TIMEOUT);
+ retries = 0;
+ do {
+
+ sr = spi_w8r8(at25->spi, AT25_RDSR);
+ if (sr < 0 || (sr & AT25_SR_nRDY)) {
+ dev_dbg(&at25->spi->dev,
+ "rdsr --> %d (%02x)\n", sr, sr);
+ /* at HZ=100, this is sloooow */
+ msleep(1);
+ continue;
+ }
+ if (!(sr & AT25_SR_nRDY))
+ break;
+ } while (retries++ < 3 || time_before_eq(jiffies, timeout));
+
+ if ((sr < 0) || (sr & AT25_SR_nRDY)) {
+ dev_err(&at25->spi->dev,
+ "write %d bytes offset %d, "
+ "timeout after %u msecs\n",
+ segment, offset,
+ jiffies_to_msecs(jiffies -
+ (timeout - EE_TIMEOUT)));
+ status = -ETIMEDOUT;
+ break;
+ }
+
+ off += segment;
+ buf += segment;
+ count -= segment;
+ written += segment;
+
+ } while (count > 0);
+
+ mutex_unlock(&at25->lock);
+
+ kfree(bounce);
+ return written ? written : status;
+}
+
+static ssize_t
+at25_bin_write(struct file *filp, struct kobject *kobj,
+ struct bin_attribute *bin_attr,
+ char *buf, loff_t off, size_t count)
+{
+ struct device *dev;
+ struct at25_data *at25;
+
+ dev = container_of(kobj, struct device, kobj);
+ at25 = dev_get_drvdata(dev);
+
+ return at25_ee_write(at25, buf, off, count);
+}
+
+/*-------------------------------------------------------------------------*/
+
+/* Let in-kernel code access the eeprom data. */
+
+static ssize_t at25_mem_read(struct memory_accessor *mem, char *buf,
+ off_t offset, size_t count)
+{
+ struct at25_data *at25 = container_of(mem, struct at25_data, mem);
+
+ return at25_ee_read(at25, buf, offset, count);
+}
+
+static ssize_t at25_mem_write(struct memory_accessor *mem, const char *buf,
+ off_t offset, size_t count)
+{
+ struct at25_data *at25 = container_of(mem, struct at25_data, mem);
+
+ return at25_ee_write(at25, buf, offset, count);
+}
+
+/*-------------------------------------------------------------------------*/
+
+static int at25_fw_to_chip(struct device *dev, struct spi_eeprom *chip)
+{
+ u32 val;
+
+ memset(chip, 0, sizeof(*chip));
+ strncpy(chip->name, "at25", sizeof(chip->name));
+
+ if (device_property_read_u32(dev, "size", &val) == 0 ||
+ device_property_read_u32(dev, "at25,byte-len", &val) == 0) {
+ chip->byte_len = val;
+ } else {
+ dev_err(dev, "Error: missing \"size\" property\n");
+ return -ENODEV;
+ }
+
+ if (device_property_read_u32(dev, "pagesize", &val) == 0 ||
+ device_property_read_u32(dev, "at25,page-size", &val) == 0) {
+ chip->page_size = (u16)val;
+ } else {
+ dev_err(dev, "Error: missing \"pagesize\" property\n");
+ return -ENODEV;
+ }
+
+ if (device_property_read_u32(dev, "at25,addr-mode", &val) == 0) {
+ chip->flags = (u16)val;
+ } else {
+ if (device_property_read_u32(dev, "address-width", &val)) {
+ dev_err(dev,
+ "Error: missing \"address-width\" property\n");
+ return -ENODEV;
+ }
+ switch (val) {
+ case 8:
+ chip->flags |= EE_ADDR1;
+ break;
+ case 16:
+ chip->flags |= EE_ADDR2;
+ break;
+ case 24:
+ chip->flags |= EE_ADDR3;
+ break;
+ default:
+ dev_err(dev,
+ "Error: bad \"address-width\" property: %u\n",
+ val);
+ return -ENODEV;
+ }
+ if (device_property_present(dev, "read-only"))
+ chip->flags |= EE_READONLY;
+ }
+ return 0;
+}
+
+static int at25_probe(struct spi_device *spi)
+{
+ struct at25_data *at25 = NULL;
+ struct spi_eeprom chip;
+ int err;
+ int sr;
+ int addrlen;
+
+ /* Chip description */
+ if (!spi->dev.platform_data) {
+ err = at25_fw_to_chip(&spi->dev, &chip);
+ if (err)
+ return err;
+ } else
+ chip = *(struct spi_eeprom *)spi->dev.platform_data;
+
+ /* For now we only support 8/16/24 bit addressing */
+ if (chip.flags & EE_ADDR1)
+ addrlen = 1;
+ else if (chip.flags & EE_ADDR2)
+ addrlen = 2;
+ else if (chip.flags & EE_ADDR3)
+ addrlen = 3;
+ else {
+ dev_dbg(&spi->dev, "unsupported address type\n");
+ return -EINVAL;
+ }
+
+ /* Ping the chip ... the status register is pretty portable,
+ * unlike probing manufacturer IDs. We do expect that system
+ * firmware didn't write it in the past few milliseconds!
+ */
+ sr = spi_w8r8(spi, AT25_RDSR);
+ if (sr < 0 || sr & AT25_SR_nRDY) {
+ dev_dbg(&spi->dev, "rdsr --> %d (%02x)\n", sr, sr);
+ return -ENXIO;
+ }
+
+ at25 = devm_kzalloc(&spi->dev, sizeof(struct at25_data), GFP_KERNEL);
+ if (!at25)
+ return -ENOMEM;
+
+ mutex_init(&at25->lock);
+ at25->chip = chip;
+ at25->spi = spi_dev_get(spi);
+ spi_set_drvdata(spi, at25);
+ at25->addrlen = addrlen;
+
+ /* Export the EEPROM bytes through sysfs, since that's convenient.
+ * And maybe to other kernel code; it might hold a board's Ethernet
+ * address, or board-specific calibration data generated on the
+ * manufacturing floor.
+ *
+ * Default to root-only access to the data; EEPROMs often hold data
+ * that's sensitive for read and/or write, like ethernet addresses,
+ * security codes, board-specific manufacturing calibrations, etc.
+ */
+ sysfs_bin_attr_init(&at25->bin);
+ at25->bin.attr.name = "eeprom";
+ at25->bin.attr.mode = S_IRUSR;
+ at25->bin.read = at25_bin_read;
+ at25->mem.read = at25_mem_read;
+
+ at25->bin.size = at25->chip.byte_len;
+ if (!(chip.flags & EE_READONLY)) {
+ at25->bin.write = at25_bin_write;
+ at25->bin.attr.mode |= S_IWUSR;
+ at25->mem.write = at25_mem_write;
+ }
+
+ err = sysfs_create_bin_file(&spi->dev.kobj, &at25->bin);
+ if (err)
+ return err;
+
+ if (chip.setup)
+ chip.setup(&at25->mem, chip.context);
+
+ dev_info(&spi->dev, "%Zd %s %s eeprom%s, pagesize %u\n",
+ (at25->bin.size < 1024)
+ ? at25->bin.size
+ : (at25->bin.size / 1024),
+ (at25->bin.size < 1024) ? "Byte" : "KByte",
+ at25->chip.name,
+ (chip.flags & EE_READONLY) ? " (readonly)" : "",
+ at25->chip.page_size);
+ return 0;
+}
+
+static int at25_remove(struct spi_device *spi)
+{
+ struct at25_data *at25;
+
+ at25 = spi_get_drvdata(spi);
+ sysfs_remove_bin_file(&spi->dev.kobj, &at25->bin);
+ return 0;
+}
+
+/*-------------------------------------------------------------------------*/
+
+static const struct of_device_id at25_of_match[] = {
+ { .compatible = "atmel,at25", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, at25_of_match);
+
+static struct spi_driver at25_driver = {
+ .driver = {
+ .name = "at25",
+ .owner = THIS_MODULE,
+ .of_match_table = at25_of_match,
+ },
+ .probe = at25_probe,
+ .remove = at25_remove,
+};
+
+module_spi_driver(at25_driver);
+
+MODULE_DESCRIPTION("Driver for most SPI EEPROMs");
+MODULE_AUTHOR("David Brownell");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("spi:at25");
diff --git a/kernel/drivers/misc/eeprom/digsy_mtc_eeprom.c b/kernel/drivers/misc/eeprom/digsy_mtc_eeprom.c
new file mode 100644
index 000000000..66d9e1bae
--- /dev/null
+++ b/kernel/drivers/misc/eeprom/digsy_mtc_eeprom.c
@@ -0,0 +1,85 @@
+/*
+ * EEPROMs access control driver for display configuration EEPROMs
+ * on DigsyMTC board.
+ *
+ * (C) 2011 DENX Software Engineering, Anatolij Gustschin <agust@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_gpio.h>
+#include <linux/eeprom_93xx46.h>
+
+#define GPIO_EEPROM_CLK 216
+#define GPIO_EEPROM_CS 210
+#define GPIO_EEPROM_DI 217
+#define GPIO_EEPROM_DO 249
+#define GPIO_EEPROM_OE 255
+#define EE_SPI_BUS_NUM 1
+
+static void digsy_mtc_op_prepare(void *p)
+{
+ /* enable */
+ gpio_set_value(GPIO_EEPROM_OE, 0);
+}
+
+static void digsy_mtc_op_finish(void *p)
+{
+ /* disable */
+ gpio_set_value(GPIO_EEPROM_OE, 1);
+}
+
+struct eeprom_93xx46_platform_data digsy_mtc_eeprom_data = {
+ .flags = EE_ADDR8,
+ .prepare = digsy_mtc_op_prepare,
+ .finish = digsy_mtc_op_finish,
+};
+
+static struct spi_gpio_platform_data eeprom_spi_gpio_data = {
+ .sck = GPIO_EEPROM_CLK,
+ .mosi = GPIO_EEPROM_DI,
+ .miso = GPIO_EEPROM_DO,
+ .num_chipselect = 1,
+};
+
+static struct platform_device digsy_mtc_eeprom = {
+ .name = "spi_gpio",
+ .id = EE_SPI_BUS_NUM,
+ .dev = {
+ .platform_data = &eeprom_spi_gpio_data,
+ },
+};
+
+static struct spi_board_info digsy_mtc_eeprom_info[] __initdata = {
+ {
+ .modalias = "93xx46",
+ .max_speed_hz = 1000000,
+ .bus_num = EE_SPI_BUS_NUM,
+ .chip_select = 0,
+ .mode = SPI_MODE_0,
+ .controller_data = (void *)GPIO_EEPROM_CS,
+ .platform_data = &digsy_mtc_eeprom_data,
+ },
+};
+
+static int __init digsy_mtc_eeprom_devices_init(void)
+{
+ int ret;
+
+ ret = gpio_request_one(GPIO_EEPROM_OE, GPIOF_OUT_INIT_HIGH,
+ "93xx46 EEPROMs OE");
+ if (ret) {
+ pr_err("can't request gpio %d\n", GPIO_EEPROM_OE);
+ return ret;
+ }
+ spi_register_board_info(digsy_mtc_eeprom_info,
+ ARRAY_SIZE(digsy_mtc_eeprom_info));
+ return platform_device_register(&digsy_mtc_eeprom);
+}
+device_initcall(digsy_mtc_eeprom_devices_init);
diff --git a/kernel/drivers/misc/eeprom/eeprom.c b/kernel/drivers/misc/eeprom/eeprom.c
new file mode 100644
index 000000000..b432873de
--- /dev/null
+++ b/kernel/drivers/misc/eeprom/eeprom.c
@@ -0,0 +1,226 @@
+/*
+ * Copyright (C) 1998, 1999 Frodo Looijaard <frodol@dds.nl> and
+ * Philip Edelbrock <phil@netroedge.com>
+ * Copyright (C) 2003 Greg Kroah-Hartman <greg@kroah.com>
+ * Copyright (C) 2003 IBM Corp.
+ * Copyright (C) 2004 Jean Delvare <jdelvare@suse.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/mutex.h>
+
+/* Addresses to scan */
+static const unsigned short normal_i2c[] = { 0x50, 0x51, 0x52, 0x53, 0x54,
+ 0x55, 0x56, 0x57, I2C_CLIENT_END };
+
+
+/* Size of EEPROM in bytes */
+#define EEPROM_SIZE 256
+
+/* possible types of eeprom devices */
+enum eeprom_nature {
+ UNKNOWN,
+ VAIO,
+};
+
+/* Each client has this additional data */
+struct eeprom_data {
+ struct mutex update_lock;
+ u8 valid; /* bitfield, bit!=0 if slice is valid */
+ unsigned long last_updated[8]; /* In jiffies, 8 slices */
+ u8 data[EEPROM_SIZE]; /* Register values */
+ enum eeprom_nature nature;
+};
+
+
+static void eeprom_update_client(struct i2c_client *client, u8 slice)
+{
+ struct eeprom_data *data = i2c_get_clientdata(client);
+ int i;
+
+ mutex_lock(&data->update_lock);
+
+ if (!(data->valid & (1 << slice)) ||
+ time_after(jiffies, data->last_updated[slice] + 300 * HZ)) {
+ dev_dbg(&client->dev, "Starting eeprom update, slice %u\n", slice);
+
+ if (i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
+ for (i = slice << 5; i < (slice + 1) << 5; i += 32)
+ if (i2c_smbus_read_i2c_block_data(client, i,
+ 32, data->data + i)
+ != 32)
+ goto exit;
+ } else {
+ for (i = slice << 5; i < (slice + 1) << 5; i += 2) {
+ int word = i2c_smbus_read_word_data(client, i);
+ if (word < 0)
+ goto exit;
+ data->data[i] = word & 0xff;
+ data->data[i + 1] = word >> 8;
+ }
+ }
+ data->last_updated[slice] = jiffies;
+ data->valid |= (1 << slice);
+ }
+exit:
+ mutex_unlock(&data->update_lock);
+}
+
+static ssize_t eeprom_read(struct file *filp, struct kobject *kobj,
+ struct bin_attribute *bin_attr,
+ char *buf, loff_t off, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(container_of(kobj, struct device, kobj));
+ struct eeprom_data *data = i2c_get_clientdata(client);
+ u8 slice;
+
+ if (off > EEPROM_SIZE)
+ return 0;
+ if (off + count > EEPROM_SIZE)
+ count = EEPROM_SIZE - off;
+
+ /* Only refresh slices which contain requested bytes */
+ for (slice = off >> 5; slice <= (off + count - 1) >> 5; slice++)
+ eeprom_update_client(client, slice);
+
+ /* Hide Vaio private settings to regular users:
+ - BIOS passwords: bytes 0x00 to 0x0f
+ - UUID: bytes 0x10 to 0x1f
+ - Serial number: 0xc0 to 0xdf */
+ if (data->nature == VAIO && !capable(CAP_SYS_ADMIN)) {
+ int i;
+
+ for (i = 0; i < count; i++) {
+ if ((off + i <= 0x1f) ||
+ (off + i >= 0xc0 && off + i <= 0xdf))
+ buf[i] = 0;
+ else
+ buf[i] = data->data[off + i];
+ }
+ } else {
+ memcpy(buf, &data->data[off], count);
+ }
+
+ return count;
+}
+
+static struct bin_attribute eeprom_attr = {
+ .attr = {
+ .name = "eeprom",
+ .mode = S_IRUGO,
+ },
+ .size = EEPROM_SIZE,
+ .read = eeprom_read,
+};
+
+/* Return 0 if detection is successful, -ENODEV otherwise */
+static int eeprom_detect(struct i2c_client *client, struct i2c_board_info *info)
+{
+ struct i2c_adapter *adapter = client->adapter;
+
+ /* EDID EEPROMs are often 24C00 EEPROMs, which answer to all
+ addresses 0x50-0x57, but we only care about 0x50. So decline
+ attaching to addresses >= 0x51 on DDC buses */
+ if (!(adapter->class & I2C_CLASS_SPD) && client->addr >= 0x51)
+ return -ENODEV;
+
+ /* There are four ways we can read the EEPROM data:
+ (1) I2C block reads (faster, but unsupported by most adapters)
+ (2) Word reads (128% overhead)
+ (3) Consecutive byte reads (88% overhead, unsafe)
+ (4) Regular byte data reads (265% overhead)
+ The third and fourth methods are not implemented by this driver
+ because all known adapters support one of the first two. */
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_WORD_DATA)
+ && !i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_I2C_BLOCK))
+ return -ENODEV;
+
+ strlcpy(info->type, "eeprom", I2C_NAME_SIZE);
+
+ return 0;
+}
+
+static int eeprom_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct i2c_adapter *adapter = client->adapter;
+ struct eeprom_data *data;
+
+ data = devm_kzalloc(&client->dev, sizeof(struct eeprom_data),
+ GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ memset(data->data, 0xff, EEPROM_SIZE);
+ i2c_set_clientdata(client, data);
+ mutex_init(&data->update_lock);
+ data->nature = UNKNOWN;
+
+ /* Detect the Vaio nature of EEPROMs.
+ We use the "PCG-" or "VGN-" prefix as the signature. */
+ if (client->addr == 0x57
+ && i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_BYTE_DATA)) {
+ char name[4];
+
+ name[0] = i2c_smbus_read_byte_data(client, 0x80);
+ name[1] = i2c_smbus_read_byte_data(client, 0x81);
+ name[2] = i2c_smbus_read_byte_data(client, 0x82);
+ name[3] = i2c_smbus_read_byte_data(client, 0x83);
+
+ if (!memcmp(name, "PCG-", 4) || !memcmp(name, "VGN-", 4)) {
+ dev_info(&client->dev, "Vaio EEPROM detected, "
+ "enabling privacy protection\n");
+ data->nature = VAIO;
+ }
+ }
+
+ /* create the sysfs eeprom file */
+ return sysfs_create_bin_file(&client->dev.kobj, &eeprom_attr);
+}
+
+static int eeprom_remove(struct i2c_client *client)
+{
+ sysfs_remove_bin_file(&client->dev.kobj, &eeprom_attr);
+
+ return 0;
+}
+
+static const struct i2c_device_id eeprom_id[] = {
+ { "eeprom", 0 },
+ { }
+};
+
+static struct i2c_driver eeprom_driver = {
+ .driver = {
+ .name = "eeprom",
+ },
+ .probe = eeprom_probe,
+ .remove = eeprom_remove,
+ .id_table = eeprom_id,
+
+ .class = I2C_CLASS_DDC | I2C_CLASS_SPD,
+ .detect = eeprom_detect,
+ .address_list = normal_i2c,
+};
+
+module_i2c_driver(eeprom_driver);
+
+MODULE_AUTHOR("Frodo Looijaard <frodol@dds.nl> and "
+ "Philip Edelbrock <phil@netroedge.com> and "
+ "Greg Kroah-Hartman <greg@kroah.com>");
+MODULE_DESCRIPTION("I2C EEPROM driver");
+MODULE_LICENSE("GPL");
diff --git a/kernel/drivers/misc/eeprom/eeprom_93cx6.c b/kernel/drivers/misc/eeprom/eeprom_93cx6.c
new file mode 100644
index 000000000..0cf2c9d67
--- /dev/null
+++ b/kernel/drivers/misc/eeprom/eeprom_93cx6.c
@@ -0,0 +1,381 @@
+/*
+ * Copyright (C) 2004 - 2006 rt2x00 SourceForge Project
+ * <http://rt2x00.serialmonkey.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Module: eeprom_93cx6
+ * Abstract: EEPROM reader routines for 93cx6 chipsets.
+ * Supported chipsets: 93c46 & 93c66.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/eeprom_93cx6.h>
+
+MODULE_AUTHOR("http://rt2x00.serialmonkey.com");
+MODULE_VERSION("1.0");
+MODULE_DESCRIPTION("EEPROM 93cx6 chip driver");
+MODULE_LICENSE("GPL");
+
+static inline void eeprom_93cx6_pulse_high(struct eeprom_93cx6 *eeprom)
+{
+ eeprom->reg_data_clock = 1;
+ eeprom->register_write(eeprom);
+
+ /*
+ * Add a short delay for the pulse to work.
+ * According to the specifications the "maximum minimum"
+ * time should be 450ns.
+ */
+ ndelay(450);
+}
+
+static inline void eeprom_93cx6_pulse_low(struct eeprom_93cx6 *eeprom)
+{
+ eeprom->reg_data_clock = 0;
+ eeprom->register_write(eeprom);
+
+ /*
+ * Add a short delay for the pulse to work.
+ * According to the specifications the "maximum minimum"
+ * time should be 450ns.
+ */
+ ndelay(450);
+}
+
+static void eeprom_93cx6_startup(struct eeprom_93cx6 *eeprom)
+{
+ /*
+ * Clear all flags, and enable chip select.
+ */
+ eeprom->register_read(eeprom);
+ eeprom->reg_data_in = 0;
+ eeprom->reg_data_out = 0;
+ eeprom->reg_data_clock = 0;
+ eeprom->reg_chip_select = 1;
+ eeprom->drive_data = 1;
+ eeprom->register_write(eeprom);
+
+ /*
+ * kick a pulse.
+ */
+ eeprom_93cx6_pulse_high(eeprom);
+ eeprom_93cx6_pulse_low(eeprom);
+}
+
+static void eeprom_93cx6_cleanup(struct eeprom_93cx6 *eeprom)
+{
+ /*
+ * Clear chip_select and data_in flags.
+ */
+ eeprom->register_read(eeprom);
+ eeprom->reg_data_in = 0;
+ eeprom->reg_chip_select = 0;
+ eeprom->register_write(eeprom);
+
+ /*
+ * kick a pulse.
+ */
+ eeprom_93cx6_pulse_high(eeprom);
+ eeprom_93cx6_pulse_low(eeprom);
+}
+
+static void eeprom_93cx6_write_bits(struct eeprom_93cx6 *eeprom,
+ const u16 data, const u16 count)
+{
+ unsigned int i;
+
+ eeprom->register_read(eeprom);
+
+ /*
+ * Clear data flags.
+ */
+ eeprom->reg_data_in = 0;
+ eeprom->reg_data_out = 0;
+ eeprom->drive_data = 1;
+
+ /*
+ * Start writing all bits.
+ */
+ for (i = count; i > 0; i--) {
+ /*
+ * Check if this bit needs to be set.
+ */
+ eeprom->reg_data_in = !!(data & (1 << (i - 1)));
+
+ /*
+ * Write the bit to the eeprom register.
+ */
+ eeprom->register_write(eeprom);
+
+ /*
+ * Kick a pulse.
+ */
+ eeprom_93cx6_pulse_high(eeprom);
+ eeprom_93cx6_pulse_low(eeprom);
+ }
+
+ eeprom->reg_data_in = 0;
+ eeprom->register_write(eeprom);
+}
+
+static void eeprom_93cx6_read_bits(struct eeprom_93cx6 *eeprom,
+ u16 *data, const u16 count)
+{
+ unsigned int i;
+ u16 buf = 0;
+
+ eeprom->register_read(eeprom);
+
+ /*
+ * Clear data flags.
+ */
+ eeprom->reg_data_in = 0;
+ eeprom->reg_data_out = 0;
+ eeprom->drive_data = 0;
+
+ /*
+ * Start reading all bits.
+ */
+ for (i = count; i > 0; i--) {
+ eeprom_93cx6_pulse_high(eeprom);
+
+ eeprom->register_read(eeprom);
+
+ /*
+ * Clear data_in flag.
+ */
+ eeprom->reg_data_in = 0;
+
+ /*
+ * Read if the bit has been set.
+ */
+ if (eeprom->reg_data_out)
+ buf |= (1 << (i - 1));
+
+ eeprom_93cx6_pulse_low(eeprom);
+ }
+
+ *data = buf;
+}
+
+/**
+ * eeprom_93cx6_read - Read a word from eeprom
+ * @eeprom: Pointer to eeprom structure
+ * @word: Word index from where we should start reading
+ * @data: target pointer where the information will have to be stored
+ *
+ * This function will read the eeprom data as host-endian word
+ * into the given data pointer.
+ */
+void eeprom_93cx6_read(struct eeprom_93cx6 *eeprom, const u8 word,
+ u16 *data)
+{
+ u16 command;
+
+ /*
+ * Initialize the eeprom register
+ */
+ eeprom_93cx6_startup(eeprom);
+
+ /*
+ * Select the read opcode and the word to be read.
+ */
+ command = (PCI_EEPROM_READ_OPCODE << eeprom->width) | word;
+ eeprom_93cx6_write_bits(eeprom, command,
+ PCI_EEPROM_WIDTH_OPCODE + eeprom->width);
+
+ /*
+ * Read the requested 16 bits.
+ */
+ eeprom_93cx6_read_bits(eeprom, data, 16);
+
+ /*
+ * Cleanup eeprom register.
+ */
+ eeprom_93cx6_cleanup(eeprom);
+}
+EXPORT_SYMBOL_GPL(eeprom_93cx6_read);
+
+/**
+ * eeprom_93cx6_multiread - Read multiple words from eeprom
+ * @eeprom: Pointer to eeprom structure
+ * @word: Word index from where we should start reading
+ * @data: target pointer where the information will have to be stored
+ * @words: Number of words that should be read.
+ *
+ * This function will read all requested words from the eeprom,
+ * this is done by calling eeprom_93cx6_read() multiple times.
+ * But with the additional change that while the eeprom_93cx6_read
+ * will return host ordered bytes, this method will return little
+ * endian words.
+ */
+void eeprom_93cx6_multiread(struct eeprom_93cx6 *eeprom, const u8 word,
+ __le16 *data, const u16 words)
+{
+ unsigned int i;
+ u16 tmp;
+
+ for (i = 0; i < words; i++) {
+ tmp = 0;
+ eeprom_93cx6_read(eeprom, word + i, &tmp);
+ data[i] = cpu_to_le16(tmp);
+ }
+}
+EXPORT_SYMBOL_GPL(eeprom_93cx6_multiread);
+
+/**
+ * eeprom_93cx6_readb - Read a byte from eeprom
+ * @eeprom: Pointer to eeprom structure
+ * @word: Byte index from where we should start reading
+ * @data: target pointer where the information will have to be stored
+ *
+ * This function will read a byte of the eeprom data
+ * into the given data pointer.
+ */
+void eeprom_93cx6_readb(struct eeprom_93cx6 *eeprom, const u8 byte,
+ u8 *data)
+{
+ u16 command;
+ u16 tmp;
+
+ /*
+ * Initialize the eeprom register
+ */
+ eeprom_93cx6_startup(eeprom);
+
+ /*
+ * Select the read opcode and the byte to be read.
+ */
+ command = (PCI_EEPROM_READ_OPCODE << (eeprom->width + 1)) | byte;
+ eeprom_93cx6_write_bits(eeprom, command,
+ PCI_EEPROM_WIDTH_OPCODE + eeprom->width + 1);
+
+ /*
+ * Read the requested 8 bits.
+ */
+ eeprom_93cx6_read_bits(eeprom, &tmp, 8);
+ *data = tmp & 0xff;
+
+ /*
+ * Cleanup eeprom register.
+ */
+ eeprom_93cx6_cleanup(eeprom);
+}
+EXPORT_SYMBOL_GPL(eeprom_93cx6_readb);
+
+/**
+ * eeprom_93cx6_multireadb - Read multiple bytes from eeprom
+ * @eeprom: Pointer to eeprom structure
+ * @byte: Index from where we should start reading
+ * @data: target pointer where the information will have to be stored
+ * @words: Number of bytes that should be read.
+ *
+ * This function will read all requested bytes from the eeprom,
+ * this is done by calling eeprom_93cx6_readb() multiple times.
+ */
+void eeprom_93cx6_multireadb(struct eeprom_93cx6 *eeprom, const u8 byte,
+ u8 *data, const u16 bytes)
+{
+ unsigned int i;
+
+ for (i = 0; i < bytes; i++)
+ eeprom_93cx6_readb(eeprom, byte + i, &data[i]);
+}
+EXPORT_SYMBOL_GPL(eeprom_93cx6_multireadb);
+
+/**
+ * eeprom_93cx6_wren - set the write enable state
+ * @eeprom: Pointer to eeprom structure
+ * @enable: true to enable writes, otherwise disable writes
+ *
+ * Set the EEPROM write enable state to either allow or deny
+ * writes depending on the @enable value.
+ */
+void eeprom_93cx6_wren(struct eeprom_93cx6 *eeprom, bool enable)
+{
+ u16 command;
+
+ /* start the command */
+ eeprom_93cx6_startup(eeprom);
+
+ /* create command to enable/disable */
+
+ command = enable ? PCI_EEPROM_EWEN_OPCODE : PCI_EEPROM_EWDS_OPCODE;
+ command <<= (eeprom->width - 2);
+
+ eeprom_93cx6_write_bits(eeprom, command,
+ PCI_EEPROM_WIDTH_OPCODE + eeprom->width);
+
+ eeprom_93cx6_cleanup(eeprom);
+}
+EXPORT_SYMBOL_GPL(eeprom_93cx6_wren);
+
+/**
+ * eeprom_93cx6_write - write data to the EEPROM
+ * @eeprom: Pointer to eeprom structure
+ * @addr: Address to write data to.
+ * @data: The data to write to address @addr.
+ *
+ * Write the @data to the specified @addr in the EEPROM and
+ * waiting for the device to finish writing.
+ *
+ * Note, since we do not expect large number of write operations
+ * we delay in between parts of the operation to avoid using excessive
+ * amounts of CPU time busy waiting.
+ */
+void eeprom_93cx6_write(struct eeprom_93cx6 *eeprom, u8 addr, u16 data)
+{
+ int timeout = 100;
+ u16 command;
+
+ /* start the command */
+ eeprom_93cx6_startup(eeprom);
+
+ command = PCI_EEPROM_WRITE_OPCODE << eeprom->width;
+ command |= addr;
+
+ /* send write command */
+ eeprom_93cx6_write_bits(eeprom, command,
+ PCI_EEPROM_WIDTH_OPCODE + eeprom->width);
+
+ /* send data */
+ eeprom_93cx6_write_bits(eeprom, data, 16);
+
+ /* get ready to check for busy */
+ eeprom->drive_data = 0;
+ eeprom->reg_chip_select = 1;
+ eeprom->register_write(eeprom);
+
+ /* wait at-least 250ns to get DO to be the busy signal */
+ usleep_range(1000, 2000);
+
+ /* wait for DO to go high to signify finish */
+
+ while (true) {
+ eeprom->register_read(eeprom);
+
+ if (eeprom->reg_data_out)
+ break;
+
+ usleep_range(1000, 2000);
+
+ if (--timeout <= 0) {
+ printk(KERN_ERR "%s: timeout\n", __func__);
+ break;
+ }
+ }
+
+ eeprom_93cx6_cleanup(eeprom);
+}
+EXPORT_SYMBOL_GPL(eeprom_93cx6_write);
diff --git a/kernel/drivers/misc/eeprom/eeprom_93xx46.c b/kernel/drivers/misc/eeprom/eeprom_93xx46.c
new file mode 100644
index 000000000..9ebeacdb8
--- /dev/null
+++ b/kernel/drivers/misc/eeprom/eeprom_93xx46.c
@@ -0,0 +1,398 @@
+/*
+ * Driver for 93xx46 EEPROMs
+ *
+ * (C) 2011 DENX Software Engineering, Anatolij Gustschin <agust@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/spi/spi.h>
+#include <linux/sysfs.h>
+#include <linux/eeprom_93xx46.h>
+
+#define OP_START 0x4
+#define OP_WRITE (OP_START | 0x1)
+#define OP_READ (OP_START | 0x2)
+#define ADDR_EWDS 0x00
+#define ADDR_ERAL 0x20
+#define ADDR_EWEN 0x30
+
+struct eeprom_93xx46_dev {
+ struct spi_device *spi;
+ struct eeprom_93xx46_platform_data *pdata;
+ struct bin_attribute bin;
+ struct mutex lock;
+ int addrlen;
+};
+
+static ssize_t
+eeprom_93xx46_bin_read(struct file *filp, struct kobject *kobj,
+ struct bin_attribute *bin_attr,
+ char *buf, loff_t off, size_t count)
+{
+ struct eeprom_93xx46_dev *edev;
+ struct device *dev;
+ struct spi_message m;
+ struct spi_transfer t[2];
+ int bits, ret;
+ u16 cmd_addr;
+
+ dev = container_of(kobj, struct device, kobj);
+ edev = dev_get_drvdata(dev);
+
+ if (unlikely(off >= edev->bin.size))
+ return 0;
+ if ((off + count) > edev->bin.size)
+ count = edev->bin.size - off;
+ if (unlikely(!count))
+ return count;
+
+ cmd_addr = OP_READ << edev->addrlen;
+
+ if (edev->addrlen == 7) {
+ cmd_addr |= off & 0x7f;
+ bits = 10;
+ } else {
+ cmd_addr |= off & 0x3f;
+ bits = 9;
+ }
+
+ dev_dbg(&edev->spi->dev, "read cmd 0x%x, %d Hz\n",
+ cmd_addr, edev->spi->max_speed_hz);
+
+ spi_message_init(&m);
+ memset(t, 0, sizeof(t));
+
+ t[0].tx_buf = (char *)&cmd_addr;
+ t[0].len = 2;
+ t[0].bits_per_word = bits;
+ spi_message_add_tail(&t[0], &m);
+
+ t[1].rx_buf = buf;
+ t[1].len = count;
+ t[1].bits_per_word = 8;
+ spi_message_add_tail(&t[1], &m);
+
+ mutex_lock(&edev->lock);
+
+ if (edev->pdata->prepare)
+ edev->pdata->prepare(edev);
+
+ ret = spi_sync(edev->spi, &m);
+ /* have to wait at least Tcsl ns */
+ ndelay(250);
+ if (ret) {
+ dev_err(&edev->spi->dev, "read %zu bytes at %d: err. %d\n",
+ count, (int)off, ret);
+ }
+
+ if (edev->pdata->finish)
+ edev->pdata->finish(edev);
+
+ mutex_unlock(&edev->lock);
+ return ret ? : count;
+}
+
+static int eeprom_93xx46_ew(struct eeprom_93xx46_dev *edev, int is_on)
+{
+ struct spi_message m;
+ struct spi_transfer t;
+ int bits, ret;
+ u16 cmd_addr;
+
+ cmd_addr = OP_START << edev->addrlen;
+ if (edev->addrlen == 7) {
+ cmd_addr |= (is_on ? ADDR_EWEN : ADDR_EWDS) << 1;
+ bits = 10;
+ } else {
+ cmd_addr |= (is_on ? ADDR_EWEN : ADDR_EWDS);
+ bits = 9;
+ }
+
+ dev_dbg(&edev->spi->dev, "ew cmd 0x%04x\n", cmd_addr);
+
+ spi_message_init(&m);
+ memset(&t, 0, sizeof(t));
+
+ t.tx_buf = &cmd_addr;
+ t.len = 2;
+ t.bits_per_word = bits;
+ spi_message_add_tail(&t, &m);
+
+ mutex_lock(&edev->lock);
+
+ if (edev->pdata->prepare)
+ edev->pdata->prepare(edev);
+
+ ret = spi_sync(edev->spi, &m);
+ /* have to wait at least Tcsl ns */
+ ndelay(250);
+ if (ret)
+ dev_err(&edev->spi->dev, "erase/write %sable error %d\n",
+ is_on ? "en" : "dis", ret);
+
+ if (edev->pdata->finish)
+ edev->pdata->finish(edev);
+
+ mutex_unlock(&edev->lock);
+ return ret;
+}
+
+static ssize_t
+eeprom_93xx46_write_word(struct eeprom_93xx46_dev *edev,
+ const char *buf, unsigned off)
+{
+ struct spi_message m;
+ struct spi_transfer t[2];
+ int bits, data_len, ret;
+ u16 cmd_addr;
+
+ cmd_addr = OP_WRITE << edev->addrlen;
+
+ if (edev->addrlen == 7) {
+ cmd_addr |= off & 0x7f;
+ bits = 10;
+ data_len = 1;
+ } else {
+ cmd_addr |= off & 0x3f;
+ bits = 9;
+ data_len = 2;
+ }
+
+ dev_dbg(&edev->spi->dev, "write cmd 0x%x\n", cmd_addr);
+
+ spi_message_init(&m);
+ memset(t, 0, sizeof(t));
+
+ t[0].tx_buf = (char *)&cmd_addr;
+ t[0].len = 2;
+ t[0].bits_per_word = bits;
+ spi_message_add_tail(&t[0], &m);
+
+ t[1].tx_buf = buf;
+ t[1].len = data_len;
+ t[1].bits_per_word = 8;
+ spi_message_add_tail(&t[1], &m);
+
+ ret = spi_sync(edev->spi, &m);
+ /* have to wait program cycle time Twc ms */
+ mdelay(6);
+ return ret;
+}
+
+static ssize_t
+eeprom_93xx46_bin_write(struct file *filp, struct kobject *kobj,
+ struct bin_attribute *bin_attr,
+ char *buf, loff_t off, size_t count)
+{
+ struct eeprom_93xx46_dev *edev;
+ struct device *dev;
+ int i, ret, step = 1;
+
+ dev = container_of(kobj, struct device, kobj);
+ edev = dev_get_drvdata(dev);
+
+ if (unlikely(off >= edev->bin.size))
+ return -EFBIG;
+ if ((off + count) > edev->bin.size)
+ count = edev->bin.size - off;
+ if (unlikely(!count))
+ return count;
+
+ /* only write even number of bytes on 16-bit devices */
+ if (edev->addrlen == 6) {
+ step = 2;
+ count &= ~1;
+ }
+
+ /* erase/write enable */
+ ret = eeprom_93xx46_ew(edev, 1);
+ if (ret)
+ return ret;
+
+ mutex_lock(&edev->lock);
+
+ if (edev->pdata->prepare)
+ edev->pdata->prepare(edev);
+
+ for (i = 0; i < count; i += step) {
+ ret = eeprom_93xx46_write_word(edev, &buf[i], off + i);
+ if (ret) {
+ dev_err(&edev->spi->dev, "write failed at %d: %d\n",
+ (int)off + i, ret);
+ break;
+ }
+ }
+
+ if (edev->pdata->finish)
+ edev->pdata->finish(edev);
+
+ mutex_unlock(&edev->lock);
+
+ /* erase/write disable */
+ eeprom_93xx46_ew(edev, 0);
+ return ret ? : count;
+}
+
+static int eeprom_93xx46_eral(struct eeprom_93xx46_dev *edev)
+{
+ struct eeprom_93xx46_platform_data *pd = edev->pdata;
+ struct spi_message m;
+ struct spi_transfer t;
+ int bits, ret;
+ u16 cmd_addr;
+
+ cmd_addr = OP_START << edev->addrlen;
+ if (edev->addrlen == 7) {
+ cmd_addr |= ADDR_ERAL << 1;
+ bits = 10;
+ } else {
+ cmd_addr |= ADDR_ERAL;
+ bits = 9;
+ }
+
+ spi_message_init(&m);
+ memset(&t, 0, sizeof(t));
+
+ t.tx_buf = &cmd_addr;
+ t.len = 2;
+ t.bits_per_word = bits;
+ spi_message_add_tail(&t, &m);
+
+ mutex_lock(&edev->lock);
+
+ if (edev->pdata->prepare)
+ edev->pdata->prepare(edev);
+
+ ret = spi_sync(edev->spi, &m);
+ if (ret)
+ dev_err(&edev->spi->dev, "erase error %d\n", ret);
+ /* have to wait erase cycle time Tec ms */
+ mdelay(6);
+
+ if (pd->finish)
+ pd->finish(edev);
+
+ mutex_unlock(&edev->lock);
+ return ret;
+}
+
+static ssize_t eeprom_93xx46_store_erase(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct eeprom_93xx46_dev *edev = dev_get_drvdata(dev);
+ int erase = 0, ret;
+
+ sscanf(buf, "%d", &erase);
+ if (erase) {
+ ret = eeprom_93xx46_ew(edev, 1);
+ if (ret)
+ return ret;
+ ret = eeprom_93xx46_eral(edev);
+ if (ret)
+ return ret;
+ ret = eeprom_93xx46_ew(edev, 0);
+ if (ret)
+ return ret;
+ }
+ return count;
+}
+static DEVICE_ATTR(erase, S_IWUSR, NULL, eeprom_93xx46_store_erase);
+
+static int eeprom_93xx46_probe(struct spi_device *spi)
+{
+ struct eeprom_93xx46_platform_data *pd;
+ struct eeprom_93xx46_dev *edev;
+ int err;
+
+ pd = spi->dev.platform_data;
+ if (!pd) {
+ dev_err(&spi->dev, "missing platform data\n");
+ return -ENODEV;
+ }
+
+ edev = kzalloc(sizeof(*edev), GFP_KERNEL);
+ if (!edev)
+ return -ENOMEM;
+
+ if (pd->flags & EE_ADDR8)
+ edev->addrlen = 7;
+ else if (pd->flags & EE_ADDR16)
+ edev->addrlen = 6;
+ else {
+ dev_err(&spi->dev, "unspecified address type\n");
+ err = -EINVAL;
+ goto fail;
+ }
+
+ mutex_init(&edev->lock);
+
+ edev->spi = spi_dev_get(spi);
+ edev->pdata = pd;
+
+ sysfs_bin_attr_init(&edev->bin);
+ edev->bin.attr.name = "eeprom";
+ edev->bin.attr.mode = S_IRUSR;
+ edev->bin.read = eeprom_93xx46_bin_read;
+ edev->bin.size = 128;
+ if (!(pd->flags & EE_READONLY)) {
+ edev->bin.write = eeprom_93xx46_bin_write;
+ edev->bin.attr.mode |= S_IWUSR;
+ }
+
+ err = sysfs_create_bin_file(&spi->dev.kobj, &edev->bin);
+ if (err)
+ goto fail;
+
+ dev_info(&spi->dev, "%d-bit eeprom %s\n",
+ (pd->flags & EE_ADDR8) ? 8 : 16,
+ (pd->flags & EE_READONLY) ? "(readonly)" : "");
+
+ if (!(pd->flags & EE_READONLY)) {
+ if (device_create_file(&spi->dev, &dev_attr_erase))
+ dev_err(&spi->dev, "can't create erase interface\n");
+ }
+
+ spi_set_drvdata(spi, edev);
+ return 0;
+fail:
+ kfree(edev);
+ return err;
+}
+
+static int eeprom_93xx46_remove(struct spi_device *spi)
+{
+ struct eeprom_93xx46_dev *edev = spi_get_drvdata(spi);
+
+ if (!(edev->pdata->flags & EE_READONLY))
+ device_remove_file(&spi->dev, &dev_attr_erase);
+
+ sysfs_remove_bin_file(&spi->dev.kobj, &edev->bin);
+ kfree(edev);
+ return 0;
+}
+
+static struct spi_driver eeprom_93xx46_driver = {
+ .driver = {
+ .name = "93xx46",
+ .owner = THIS_MODULE,
+ },
+ .probe = eeprom_93xx46_probe,
+ .remove = eeprom_93xx46_remove,
+};
+
+module_spi_driver(eeprom_93xx46_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Driver for 93xx46 EEPROMs");
+MODULE_AUTHOR("Anatolij Gustschin <agust@denx.de>");
+MODULE_ALIAS("spi:93xx46");
diff --git a/kernel/drivers/misc/eeprom/max6875.c b/kernel/drivers/misc/eeprom/max6875.c
new file mode 100644
index 000000000..580ff9df5
--- /dev/null
+++ b/kernel/drivers/misc/eeprom/max6875.c
@@ -0,0 +1,214 @@
+/*
+ * max6875.c - driver for MAX6874/MAX6875
+ *
+ * Copyright (C) 2005 Ben Gardner <bgardner@wabtec.com>
+ *
+ * Based on eeprom.c
+ *
+ * The MAX6875 has a bank of registers and two banks of EEPROM.
+ * Address ranges are defined as follows:
+ * * 0x0000 - 0x0046 = configuration registers
+ * * 0x8000 - 0x8046 = configuration EEPROM
+ * * 0x8100 - 0x82FF = user EEPROM
+ *
+ * This driver makes the user EEPROM available for read.
+ *
+ * The registers & config EEPROM should be accessed via i2c-dev.
+ *
+ * The MAX6875 ignores the lowest address bit, so each chip responds to
+ * two addresses - 0x50/0x51 and 0x52/0x53.
+ *
+ * Note that the MAX6875 uses i2c_smbus_write_byte_data() to set the read
+ * address, so this driver is destructive if loaded for the wrong EEPROM chip.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/mutex.h>
+
+/* The MAX6875 can only read/write 16 bytes at a time */
+#define SLICE_SIZE 16
+#define SLICE_BITS 4
+
+/* USER EEPROM is at addresses 0x8100 - 0x82FF */
+#define USER_EEPROM_BASE 0x8100
+#define USER_EEPROM_SIZE 0x0200
+#define USER_EEPROM_SLICES 32
+
+/* MAX6875 commands */
+#define MAX6875_CMD_BLK_READ 0x84
+
+/* Each client has this additional data */
+struct max6875_data {
+ struct i2c_client *fake_client;
+ struct mutex update_lock;
+
+ u32 valid;
+ u8 data[USER_EEPROM_SIZE];
+ unsigned long last_updated[USER_EEPROM_SLICES];
+};
+
+static void max6875_update_slice(struct i2c_client *client, int slice)
+{
+ struct max6875_data *data = i2c_get_clientdata(client);
+ int i, j, addr;
+ u8 *buf;
+
+ if (slice >= USER_EEPROM_SLICES)
+ return;
+
+ mutex_lock(&data->update_lock);
+
+ buf = &data->data[slice << SLICE_BITS];
+
+ if (!(data->valid & (1 << slice)) ||
+ time_after(jiffies, data->last_updated[slice])) {
+
+ dev_dbg(&client->dev, "Starting update of slice %u\n", slice);
+
+ data->valid &= ~(1 << slice);
+
+ addr = USER_EEPROM_BASE + (slice << SLICE_BITS);
+
+ /* select the eeprom address */
+ if (i2c_smbus_write_byte_data(client, addr >> 8, addr & 0xFF)) {
+ dev_err(&client->dev, "address set failed\n");
+ goto exit_up;
+ }
+
+ if (i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
+ if (i2c_smbus_read_i2c_block_data(client,
+ MAX6875_CMD_BLK_READ,
+ SLICE_SIZE,
+ buf) != SLICE_SIZE) {
+ goto exit_up;
+ }
+ } else {
+ for (i = 0; i < SLICE_SIZE; i++) {
+ j = i2c_smbus_read_byte(client);
+ if (j < 0) {
+ goto exit_up;
+ }
+ buf[i] = j;
+ }
+ }
+ data->last_updated[slice] = jiffies;
+ data->valid |= (1 << slice);
+ }
+exit_up:
+ mutex_unlock(&data->update_lock);
+}
+
+static ssize_t max6875_read(struct file *filp, struct kobject *kobj,
+ struct bin_attribute *bin_attr,
+ char *buf, loff_t off, size_t count)
+{
+ struct i2c_client *client = kobj_to_i2c_client(kobj);
+ struct max6875_data *data = i2c_get_clientdata(client);
+ int slice, max_slice;
+
+ if (off > USER_EEPROM_SIZE)
+ return 0;
+
+ if (off + count > USER_EEPROM_SIZE)
+ count = USER_EEPROM_SIZE - off;
+
+ /* refresh slices which contain requested bytes */
+ max_slice = (off + count - 1) >> SLICE_BITS;
+ for (slice = (off >> SLICE_BITS); slice <= max_slice; slice++)
+ max6875_update_slice(client, slice);
+
+ memcpy(buf, &data->data[off], count);
+
+ return count;
+}
+
+static struct bin_attribute user_eeprom_attr = {
+ .attr = {
+ .name = "eeprom",
+ .mode = S_IRUGO,
+ },
+ .size = USER_EEPROM_SIZE,
+ .read = max6875_read,
+};
+
+static int max6875_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct i2c_adapter *adapter = client->adapter;
+ struct max6875_data *data;
+ int err;
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WRITE_BYTE_DATA
+ | I2C_FUNC_SMBUS_READ_BYTE))
+ return -ENODEV;
+
+ /* Only bind to even addresses */
+ if (client->addr & 1)
+ return -ENODEV;
+
+ if (!(data = kzalloc(sizeof(struct max6875_data), GFP_KERNEL)))
+ return -ENOMEM;
+
+ /* A fake client is created on the odd address */
+ data->fake_client = i2c_new_dummy(client->adapter, client->addr + 1);
+ if (!data->fake_client) {
+ err = -ENOMEM;
+ goto exit_kfree;
+ }
+
+ /* Init real i2c_client */
+ i2c_set_clientdata(client, data);
+ mutex_init(&data->update_lock);
+
+ err = sysfs_create_bin_file(&client->dev.kobj, &user_eeprom_attr);
+ if (err)
+ goto exit_remove_fake;
+
+ return 0;
+
+exit_remove_fake:
+ i2c_unregister_device(data->fake_client);
+exit_kfree:
+ kfree(data);
+ return err;
+}
+
+static int max6875_remove(struct i2c_client *client)
+{
+ struct max6875_data *data = i2c_get_clientdata(client);
+
+ i2c_unregister_device(data->fake_client);
+
+ sysfs_remove_bin_file(&client->dev.kobj, &user_eeprom_attr);
+ kfree(data);
+
+ return 0;
+}
+
+static const struct i2c_device_id max6875_id[] = {
+ { "max6875", 0 },
+ { }
+};
+
+static struct i2c_driver max6875_driver = {
+ .driver = {
+ .name = "max6875",
+ },
+ .probe = max6875_probe,
+ .remove = max6875_remove,
+ .id_table = max6875_id,
+};
+
+module_i2c_driver(max6875_driver);
+
+MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>");
+MODULE_DESCRIPTION("MAX6875 driver");
+MODULE_LICENSE("GPL");
diff --git a/kernel/drivers/misc/eeprom/sunxi_sid.c b/kernel/drivers/misc/eeprom/sunxi_sid.c
new file mode 100644
index 000000000..8385177ff
--- /dev/null
+++ b/kernel/drivers/misc/eeprom/sunxi_sid.c
@@ -0,0 +1,156 @@
+/*
+ * Copyright (c) 2013 Oliver Schinagl <oliver@schinagl.nl>
+ * http://www.linux-sunxi.org
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * This driver exposes the Allwinner security ID, efuses exported in byte-
+ * sized chunks.
+ */
+
+#include <linux/compiler.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/export.h>
+#include <linux/fs.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/kobject.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/random.h>
+#include <linux/slab.h>
+#include <linux/stat.h>
+#include <linux/sysfs.h>
+#include <linux/types.h>
+
+#define DRV_NAME "sunxi-sid"
+
+struct sunxi_sid_data {
+ void __iomem *reg_base;
+ unsigned int keysize;
+};
+
+/* We read the entire key, due to a 32 bit read alignment requirement. Since we
+ * want to return the requested byte, this results in somewhat slower code and
+ * uses 4 times more reads as needed but keeps code simpler. Since the SID is
+ * only very rarely probed, this is not really an issue.
+ */
+static u8 sunxi_sid_read_byte(const struct sunxi_sid_data *sid_data,
+ const unsigned int offset)
+{
+ u32 sid_key;
+
+ if (offset >= sid_data->keysize)
+ return 0;
+
+ sid_key = ioread32be(sid_data->reg_base + round_down(offset, 4));
+ sid_key >>= (offset % 4) * 8;
+
+ return sid_key; /* Only return the last byte */
+}
+
+static ssize_t sid_read(struct file *fd, struct kobject *kobj,
+ struct bin_attribute *attr, char *buf,
+ loff_t pos, size_t size)
+{
+ struct platform_device *pdev;
+ struct sunxi_sid_data *sid_data;
+ int i;
+
+ pdev = to_platform_device(kobj_to_dev(kobj));
+ sid_data = platform_get_drvdata(pdev);
+
+ if (pos < 0 || pos >= sid_data->keysize)
+ return 0;
+ if (size > sid_data->keysize - pos)
+ size = sid_data->keysize - pos;
+
+ for (i = 0; i < size; i++)
+ buf[i] = sunxi_sid_read_byte(sid_data, pos + i);
+
+ return i;
+}
+
+static struct bin_attribute sid_bin_attr = {
+ .attr = { .name = "eeprom", .mode = S_IRUGO, },
+ .read = sid_read,
+};
+
+static int sunxi_sid_remove(struct platform_device *pdev)
+{
+ device_remove_bin_file(&pdev->dev, &sid_bin_attr);
+ dev_dbg(&pdev->dev, "driver unloaded\n");
+
+ return 0;
+}
+
+static const struct of_device_id sunxi_sid_of_match[] = {
+ { .compatible = "allwinner,sun4i-a10-sid", .data = (void *)16},
+ { .compatible = "allwinner,sun7i-a20-sid", .data = (void *)512},
+ {/* sentinel */},
+};
+MODULE_DEVICE_TABLE(of, sunxi_sid_of_match);
+
+static int sunxi_sid_probe(struct platform_device *pdev)
+{
+ struct sunxi_sid_data *sid_data;
+ struct resource *res;
+ const struct of_device_id *of_dev_id;
+ u8 *entropy;
+ unsigned int i;
+
+ sid_data = devm_kzalloc(&pdev->dev, sizeof(struct sunxi_sid_data),
+ GFP_KERNEL);
+ if (!sid_data)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ sid_data->reg_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(sid_data->reg_base))
+ return PTR_ERR(sid_data->reg_base);
+
+ of_dev_id = of_match_device(sunxi_sid_of_match, &pdev->dev);
+ if (!of_dev_id)
+ return -ENODEV;
+ sid_data->keysize = (int)of_dev_id->data;
+
+ platform_set_drvdata(pdev, sid_data);
+
+ sid_bin_attr.size = sid_data->keysize;
+ if (device_create_bin_file(&pdev->dev, &sid_bin_attr))
+ return -ENODEV;
+
+ entropy = kzalloc(sizeof(u8) * sid_data->keysize, GFP_KERNEL);
+ for (i = 0; i < sid_data->keysize; i++)
+ entropy[i] = sunxi_sid_read_byte(sid_data, i);
+ add_device_randomness(entropy, sid_data->keysize);
+ kfree(entropy);
+
+ dev_dbg(&pdev->dev, "loaded\n");
+
+ return 0;
+}
+
+static struct platform_driver sunxi_sid_driver = {
+ .probe = sunxi_sid_probe,
+ .remove = sunxi_sid_remove,
+ .driver = {
+ .name = DRV_NAME,
+ .of_match_table = sunxi_sid_of_match,
+ },
+};
+module_platform_driver(sunxi_sid_driver);
+
+MODULE_AUTHOR("Oliver Schinagl <oliver@schinagl.nl>");
+MODULE_DESCRIPTION("Allwinner sunxi security id driver");
+MODULE_LICENSE("GPL");