summaryrefslogtreecommitdiffstats
path: root/kernel/arch/cris/arch-v32/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/arch/cris/arch-v32/drivers')
-rw-r--r--kernel/arch/cris/arch-v32/drivers/Kconfig167
-rw-r--r--kernel/arch/cris/arch-v32/drivers/Makefile1
-rw-r--r--kernel/arch/cris/arch-v32/drivers/axisflashmap.c49
-rw-r--r--kernel/arch/cris/arch-v32/drivers/i2c.c751
-rw-r--r--kernel/arch/cris/arch-v32/drivers/i2c.h16
-rw-r--r--kernel/arch/cris/arch-v32/drivers/mach-a3/Makefile1
-rw-r--r--kernel/arch/cris/arch-v32/drivers/mach-a3/gpio.c999
-rw-r--r--kernel/arch/cris/arch-v32/drivers/mach-fs/Makefile1
-rw-r--r--kernel/arch/cris/arch-v32/drivers/mach-fs/gpio.c979
-rw-r--r--kernel/arch/cris/arch-v32/drivers/sync_serial.c2
10 files changed, 12 insertions, 2954 deletions
diff --git a/kernel/arch/cris/arch-v32/drivers/Kconfig b/kernel/arch/cris/arch-v32/drivers/Kconfig
index 4fc16b44f..2735eb767 100644
--- a/kernel/arch/cris/arch-v32/drivers/Kconfig
+++ b/kernel/arch/cris/arch-v32/drivers/Kconfig
@@ -149,173 +149,6 @@ config ETRAX_NANDBOOT
Say Y if your boot code, kernel and root file system is in
NAND flash. Say N if they are in NOR flash.
-config ETRAX_I2C
- bool "I2C driver"
- depends on ETRAX_ARCH_V32
- help
- This option enables the I2C driver used by e.g. the RTC driver.
-
-config ETRAX_V32_I2C_DATA_PORT
- string "I2C data pin"
- depends on ETRAX_I2C
- help
- The pin to use for I2C data.
-
-config ETRAX_V32_I2C_CLK_PORT
- string "I2C clock pin"
- depends on ETRAX_I2C
- help
- The pin to use for I2C clock.
-
-config ETRAX_GPIO
- bool "GPIO support"
- depends on ETRAX_ARCH_V32
- ---help---
- Enables the ETRAX general port device (major 120, minors 0-4).
- You can use this driver to access the general port bits. It supports
- these ioctl's:
- #include <linux/etraxgpio.h>
- fd = open("/dev/gpioa", O_RDWR); // or /dev/gpiob
- ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_SETBITS), bits_to_set);
- ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_CLRBITS), bits_to_clear);
- err = ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_READ_INBITS), &val);
- Remember that you need to setup the port directions appropriately in
- the General configuration.
-
-config ETRAX_VIRTUAL_GPIO
- bool "Virtual GPIO support"
- depends on ETRAX_GPIO
- help
- Enables the virtual Etrax general port device (major 120, minor 6).
- It uses an I/O expander for the I2C-bus.
-
-config ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN
- int "Virtual GPIO interrupt pin on PA pin"
- range 0 7
- depends on ETRAX_VIRTUAL_GPIO
- help
- The pin to use on PA for virtual gpio interrupt.
-
-config ETRAX_PA_CHANGEABLE_DIR
- hex "PA user changeable dir mask"
- depends on ETRAX_GPIO
- default "0x00" if ETRAXFS
- default "0x00000000" if !ETRAXFS
- help
- This is a bitmask (8 bits) with information of what bits in PA that a
- user can change direction on using ioctl's.
- Bit set = changeable.
- You probably want 0 here, but it depends on your hardware.
-
-config ETRAX_PA_CHANGEABLE_BITS
- hex "PA user changeable bits mask"
- depends on ETRAX_GPIO
- default "0x00" if ETRAXFS
- default "0x00000000" if !ETRAXFS
- help
- This is a bitmask (8 bits) with information of what bits in PA
- that a user can change the value on using ioctl's.
- Bit set = changeable.
-
-config ETRAX_PB_CHANGEABLE_DIR
- hex "PB user changeable dir mask"
- depends on ETRAX_GPIO
- default "0x00000" if ETRAXFS
- default "0x00000000" if !ETRAXFS
- help
- This is a bitmask (18 bits) with information of what bits in PB
- that a user can change direction on using ioctl's.
- Bit set = changeable.
- You probably want 0 here, but it depends on your hardware.
-
-config ETRAX_PB_CHANGEABLE_BITS
- hex "PB user changeable bits mask"
- depends on ETRAX_GPIO
- default "0x00000" if ETRAXFS
- default "0x00000000" if !ETRAXFS
- help
- This is a bitmask (18 bits) with information of what bits in PB
- that a user can change the value on using ioctl's.
- Bit set = changeable.
-
-config ETRAX_PC_CHANGEABLE_DIR
- hex "PC user changeable dir mask"
- depends on ETRAX_GPIO
- default "0x00000" if ETRAXFS
- default "0x00000000" if !ETRAXFS
- help
- This is a bitmask (18 bits) with information of what bits in PC
- that a user can change direction on using ioctl's.
- Bit set = changeable.
- You probably want 0 here, but it depends on your hardware.
-
-config ETRAX_PC_CHANGEABLE_BITS
- hex "PC user changeable bits mask"
- depends on ETRAX_GPIO
- default "0x00000" if ETRAXFS
- default "0x00000000" if ETRAXFS
- help
- This is a bitmask (18 bits) with information of what bits in PC
- that a user can change the value on using ioctl's.
- Bit set = changeable.
-
-config ETRAX_PD_CHANGEABLE_DIR
- hex "PD user changeable dir mask"
- depends on ETRAX_GPIO && ETRAXFS
- default "0x00000"
- help
- This is a bitmask (18 bits) with information of what bits in PD
- that a user can change direction on using ioctl's.
- Bit set = changeable.
- You probably want 0x00000 here, but it depends on your hardware.
-
-config ETRAX_PD_CHANGEABLE_BITS
- hex "PD user changeable bits mask"
- depends on ETRAX_GPIO && ETRAXFS
- default "0x00000"
- help
- This is a bitmask (18 bits) with information of what bits in PD
- that a user can change the value on using ioctl's.
- Bit set = changeable.
-
-config ETRAX_PE_CHANGEABLE_DIR
- hex "PE user changeable dir mask"
- depends on ETRAX_GPIO && ETRAXFS
- default "0x00000"
- help
- This is a bitmask (18 bits) with information of what bits in PE
- that a user can change direction on using ioctl's.
- Bit set = changeable.
- You probably want 0x00000 here, but it depends on your hardware.
-
-config ETRAX_PE_CHANGEABLE_BITS
- hex "PE user changeable bits mask"
- depends on ETRAX_GPIO && ETRAXFS
- default "0x00000"
- help
- This is a bitmask (18 bits) with information of what bits in PE
- that a user can change the value on using ioctl's.
- Bit set = changeable.
-
-config ETRAX_PV_CHANGEABLE_DIR
- hex "PV user changeable dir mask"
- depends on ETRAX_VIRTUAL_GPIO
- default "0x0000"
- help
- This is a bitmask (16 bits) with information of what bits in PV
- that a user can change direction on using ioctl's.
- Bit set = changeable.
- You probably want 0x0000 here, but it depends on your hardware.
-
-config ETRAX_PV_CHANGEABLE_BITS
- hex "PV user changeable bits mask"
- depends on ETRAX_VIRTUAL_GPIO
- default "0x0000"
- help
- This is a bitmask (16 bits) with information of what bits in PV
- that a user can change the value on using ioctl's.
- Bit set = changeable.
-
config ETRAX_CARDBUS
bool "Cardbus support"
depends on ETRAX_ARCH_V32
diff --git a/kernel/arch/cris/arch-v32/drivers/Makefile b/kernel/arch/cris/arch-v32/drivers/Makefile
index 15fbfefce..b5a75fdce 100644
--- a/kernel/arch/cris/arch-v32/drivers/Makefile
+++ b/kernel/arch/cris/arch-v32/drivers/Makefile
@@ -7,6 +7,5 @@ obj-$(CONFIG_ETRAX_AXISFLASHMAP) += axisflashmap.o
obj-$(CONFIG_ETRAXFS) += mach-fs/
obj-$(CONFIG_CRIS_MACH_ARTPEC3) += mach-a3/
obj-$(CONFIG_ETRAX_IOP_FW_LOAD) += iop_fw_load.o
-obj-$(CONFIG_ETRAX_I2C) += i2c.o
obj-$(CONFIG_ETRAX_SYNCHRONOUS_SERIAL) += sync_serial.o
obj-$(CONFIG_PCI) += pci/
diff --git a/kernel/arch/cris/arch-v32/drivers/axisflashmap.c b/kernel/arch/cris/arch-v32/drivers/axisflashmap.c
index 28dd77144..c6309a182 100644
--- a/kernel/arch/cris/arch-v32/drivers/axisflashmap.c
+++ b/kernel/arch/cris/arch-v32/drivers/axisflashmap.c
@@ -313,6 +313,7 @@ static int __init init_axis_flash(void)
size_t len;
int ram_rootfs_partition = -1; /* -1 => no RAM rootfs partition */
int part;
+ struct mtd_partition *partition;
/* We need a root fs. If it resides in RAM, we need to use an
* MTDRAM device, so it must be enabled in the kernel config,
@@ -329,7 +330,7 @@ static int __init init_axis_flash(void)
main_mtd = flash_probe();
if (main_mtd)
- printk(KERN_INFO "%s: 0x%08x bytes of NOR flash memory.\n",
+ printk(KERN_INFO "%s: 0x%08llx bytes of NOR flash memory.\n",
main_mtd->name, main_mtd->size);
#ifdef CONFIG_ETRAX_NANDFLASH
@@ -360,7 +361,7 @@ static int __init init_axis_flash(void)
#if 0 /* Dump flash memory so we can see what is going on */
if (main_mtd) {
- int sectoraddr, i;
+ int sectoraddr;
for (sectoraddr = 0; sectoraddr < 2*65536+4096;
sectoraddr += PAGESIZE) {
main_mtd->read(main_mtd, sectoraddr, PAGESIZE, &len,
@@ -368,30 +369,16 @@ static int __init init_axis_flash(void)
printk(KERN_INFO
"Sector at %d (length %d):\n",
sectoraddr, len);
- for (i = 0; i < PAGESIZE; i += 16) {
- printk(KERN_INFO
- "%02x %02x %02x %02x "
- "%02x %02x %02x %02x "
- "%02x %02x %02x %02x "
- "%02x %02x %02x %02x\n",
- page[i] & 255, page[i+1] & 255,
- page[i+2] & 255, page[i+3] & 255,
- page[i+4] & 255, page[i+5] & 255,
- page[i+6] & 255, page[i+7] & 255,
- page[i+8] & 255, page[i+9] & 255,
- page[i+10] & 255, page[i+11] & 255,
- page[i+12] & 255, page[i+13] & 255,
- page[i+14] & 255, page[i+15] & 255);
- }
+ print_hex_dump(KERN_INFO, "", DUMP_PREFIX_NONE, 16, 1, page, PAGESIZE, false);
}
}
#endif
if (main_mtd) {
+ loff_t ptable_sector = CONFIG_ETRAX_PTABLE_SECTOR;
main_mtd->owner = THIS_MODULE;
axisflash_mtd = main_mtd;
- loff_t ptable_sector = CONFIG_ETRAX_PTABLE_SECTOR;
/* First partition (rescue) is always set to the default. */
pidx++;
@@ -416,25 +403,11 @@ static int __init init_axis_flash(void)
#if 0 /* Dump partition table so we can see what is going on */
printk(KERN_INFO
- "axisflashmap: flash read %d bytes at 0x%08x, data: "
- "%02x %02x %02x %02x %02x %02x %02x %02x\n",
- len, CONFIG_ETRAX_PTABLE_SECTOR,
- page[0] & 255, page[1] & 255,
- page[2] & 255, page[3] & 255,
- page[4] & 255, page[5] & 255,
- page[6] & 255, page[7] & 255);
+ "axisflashmap: flash read %d bytes at 0x%08x, data: %8ph\n",
+ len, CONFIG_ETRAX_PTABLE_SECTOR, page);
printk(KERN_INFO
- "axisflashmap: partition table offset %d, data: "
- "%02x %02x %02x %02x %02x %02x %02x %02x\n",
- PARTITION_TABLE_OFFSET,
- page[PARTITION_TABLE_OFFSET+0] & 255,
- page[PARTITION_TABLE_OFFSET+1] & 255,
- page[PARTITION_TABLE_OFFSET+2] & 255,
- page[PARTITION_TABLE_OFFSET+3] & 255,
- page[PARTITION_TABLE_OFFSET+4] & 255,
- page[PARTITION_TABLE_OFFSET+5] & 255,
- page[PARTITION_TABLE_OFFSET+6] & 255,
- page[PARTITION_TABLE_OFFSET+7] & 255);
+ "axisflashmap: partition table offset %d, data: %8ph\n",
+ PARTITION_TABLE_OFFSET, page + PARTITION_TABLE_OFFSET);
#endif
}
@@ -517,7 +490,7 @@ static int __init init_axis_flash(void)
/* Decide whether to use default partition table. */
/* Only use default table if we actually have a device (main_mtd) */
- struct mtd_partition *partition = &axis_partitions[0];
+ partition = &axis_partitions[0];
if (main_mtd && !ptable_ok) {
memcpy(axis_partitions, axis_default_partitions,
sizeof(axis_default_partitions));
@@ -580,7 +553,7 @@ static int __init init_axis_flash(void)
printk(KERN_INFO "axisflashmap: Adding RAM partition "
"for rootfs image.\n");
err = mtdram_init_device(mtd_ram,
- (void *)partition[part].offset,
+ (void *)(u_int32_t)partition[part].offset,
partition[part].size,
partition[part].name);
if (err)
diff --git a/kernel/arch/cris/arch-v32/drivers/i2c.c b/kernel/arch/cris/arch-v32/drivers/i2c.c
deleted file mode 100644
index 3b2c82ce8..000000000
--- a/kernel/arch/cris/arch-v32/drivers/i2c.c
+++ /dev/null
@@ -1,751 +0,0 @@
-/*!***************************************************************************
-*!
-*! FILE NAME : i2c.c
-*!
-*! DESCRIPTION: implements an interface for IIC/I2C, both directly from other
-*! kernel modules (i2c_writereg/readreg) and from userspace using
-*! ioctl()'s
-*!
-*! Nov 30 1998 Torbjorn Eliasson Initial version.
-*! Bjorn Wesen Elinux kernel version.
-*! Jan 14 2000 Johan Adolfsson Fixed PB shadow register stuff -
-*! don't use PB_I2C if DS1302 uses same bits,
-*! use PB.
-*| June 23 2003 Pieter Grimmerink Added 'i2c_sendnack'. i2c_readreg now
-*| generates nack on last received byte,
-*| instead of ack.
-*| i2c_getack changed data level while clock
-*| was high, causing DS75 to see a stop condition
-*!
-*! ---------------------------------------------------------------------------
-*!
-*! (C) Copyright 1999-2007 Axis Communications AB, LUND, SWEDEN
-*!
-*!***************************************************************************/
-
-/****************** INCLUDE FILES SECTION ***********************************/
-
-#include <linux/module.h>
-#include <linux/sched.h>
-#include <linux/errno.h>
-#include <linux/kernel.h>
-#include <linux/fs.h>
-#include <linux/string.h>
-#include <linux/init.h>
-#include <linux/mutex.h>
-
-#include <asm/etraxi2c.h>
-
-#include <asm/io.h>
-#include <asm/delay.h>
-
-#include "i2c.h"
-
-/****************** I2C DEFINITION SECTION *************************/
-
-#define D(x)
-
-#define I2C_MAJOR 123 /* LOCAL/EXPERIMENTAL */
-static DEFINE_MUTEX(i2c_mutex);
-static const char i2c_name[] = "i2c";
-
-#define CLOCK_LOW_TIME 8
-#define CLOCK_HIGH_TIME 8
-#define START_CONDITION_HOLD_TIME 8
-#define STOP_CONDITION_HOLD_TIME 8
-#define ENABLE_OUTPUT 0x01
-#define ENABLE_INPUT 0x00
-#define I2C_CLOCK_HIGH 1
-#define I2C_CLOCK_LOW 0
-#define I2C_DATA_HIGH 1
-#define I2C_DATA_LOW 0
-
-#define i2c_enable()
-#define i2c_disable()
-
-/* enable or disable output-enable, to select output or input on the i2c bus */
-
-#define i2c_dir_out() crisv32_io_set_dir(&cris_i2c_data, crisv32_io_dir_out)
-#define i2c_dir_in() crisv32_io_set_dir(&cris_i2c_data, crisv32_io_dir_in)
-
-/* control the i2c clock and data signals */
-
-#define i2c_clk(x) crisv32_io_set(&cris_i2c_clk, x)
-#define i2c_data(x) crisv32_io_set(&cris_i2c_data, x)
-
-/* read a bit from the i2c interface */
-
-#define i2c_getbit() crisv32_io_rd(&cris_i2c_data)
-
-#define i2c_delay(usecs) udelay(usecs)
-
-static DEFINE_SPINLOCK(i2c_lock); /* Protect directions etc */
-
-/****************** VARIABLE SECTION ************************************/
-
-static struct crisv32_iopin cris_i2c_clk;
-static struct crisv32_iopin cris_i2c_data;
-
-/****************** FUNCTION DEFINITION SECTION *************************/
-
-
-/* generate i2c start condition */
-
-void
-i2c_start(void)
-{
- /*
- * SCL=1 SDA=1
- */
- i2c_dir_out();
- i2c_delay(CLOCK_HIGH_TIME/6);
- i2c_data(I2C_DATA_HIGH);
- i2c_clk(I2C_CLOCK_HIGH);
- i2c_delay(CLOCK_HIGH_TIME);
- /*
- * SCL=1 SDA=0
- */
- i2c_data(I2C_DATA_LOW);
- i2c_delay(START_CONDITION_HOLD_TIME);
- /*
- * SCL=0 SDA=0
- */
- i2c_clk(I2C_CLOCK_LOW);
- i2c_delay(CLOCK_LOW_TIME);
-}
-
-/* generate i2c stop condition */
-
-void
-i2c_stop(void)
-{
- i2c_dir_out();
-
- /*
- * SCL=0 SDA=0
- */
- i2c_clk(I2C_CLOCK_LOW);
- i2c_data(I2C_DATA_LOW);
- i2c_delay(CLOCK_LOW_TIME*2);
- /*
- * SCL=1 SDA=0
- */
- i2c_clk(I2C_CLOCK_HIGH);
- i2c_delay(CLOCK_HIGH_TIME*2);
- /*
- * SCL=1 SDA=1
- */
- i2c_data(I2C_DATA_HIGH);
- i2c_delay(STOP_CONDITION_HOLD_TIME);
-
- i2c_dir_in();
-}
-
-/* write a byte to the i2c interface */
-
-void
-i2c_outbyte(unsigned char x)
-{
- int i;
-
- i2c_dir_out();
-
- for (i = 0; i < 8; i++) {
- if (x & 0x80) {
- i2c_data(I2C_DATA_HIGH);
- } else {
- i2c_data(I2C_DATA_LOW);
- }
-
- i2c_delay(CLOCK_LOW_TIME/2);
- i2c_clk(I2C_CLOCK_HIGH);
- i2c_delay(CLOCK_HIGH_TIME);
- i2c_clk(I2C_CLOCK_LOW);
- i2c_delay(CLOCK_LOW_TIME/2);
- x <<= 1;
- }
- i2c_data(I2C_DATA_LOW);
- i2c_delay(CLOCK_LOW_TIME/2);
-
- /*
- * enable input
- */
- i2c_dir_in();
-}
-
-/* read a byte from the i2c interface */
-
-unsigned char
-i2c_inbyte(void)
-{
- unsigned char aBitByte = 0;
- int i;
-
- /* Switch off I2C to get bit */
- i2c_disable();
- i2c_dir_in();
- i2c_delay(CLOCK_HIGH_TIME/2);
-
- /* Get bit */
- aBitByte |= i2c_getbit();
-
- /* Enable I2C */
- i2c_enable();
- i2c_delay(CLOCK_LOW_TIME/2);
-
- for (i = 1; i < 8; i++) {
- aBitByte <<= 1;
- /* Clock pulse */
- i2c_clk(I2C_CLOCK_HIGH);
- i2c_delay(CLOCK_HIGH_TIME);
- i2c_clk(I2C_CLOCK_LOW);
- i2c_delay(CLOCK_LOW_TIME);
-
- /* Switch off I2C to get bit */
- i2c_disable();
- i2c_dir_in();
- i2c_delay(CLOCK_HIGH_TIME/2);
-
- /* Get bit */
- aBitByte |= i2c_getbit();
-
- /* Enable I2C */
- i2c_enable();
- i2c_delay(CLOCK_LOW_TIME/2);
- }
- i2c_clk(I2C_CLOCK_HIGH);
- i2c_delay(CLOCK_HIGH_TIME);
-
- /*
- * we leave the clock low, getbyte is usually followed
- * by sendack/nack, they assume the clock to be low
- */
- i2c_clk(I2C_CLOCK_LOW);
- return aBitByte;
-}
-
-/*#---------------------------------------------------------------------------
-*#
-*# FUNCTION NAME: i2c_getack
-*#
-*# DESCRIPTION : checks if ack was received from ic2
-*#
-*#--------------------------------------------------------------------------*/
-
-int
-i2c_getack(void)
-{
- int ack = 1;
- /*
- * enable output
- */
- i2c_dir_out();
- /*
- * Release data bus by setting
- * data high
- */
- i2c_data(I2C_DATA_HIGH);
- /*
- * enable input
- */
- i2c_dir_in();
- i2c_delay(CLOCK_HIGH_TIME/4);
- /*
- * generate ACK clock pulse
- */
- i2c_clk(I2C_CLOCK_HIGH);
-#if 0
- /*
- * Use PORT PB instead of I2C
- * for input. (I2C not working)
- */
- i2c_clk(1);
- i2c_data(1);
- /*
- * switch off I2C
- */
- i2c_data(1);
- i2c_disable();
- i2c_dir_in();
-#endif
-
- /*
- * now wait for ack
- */
- i2c_delay(CLOCK_HIGH_TIME/2);
- /*
- * check for ack
- */
- if (i2c_getbit())
- ack = 0;
- i2c_delay(CLOCK_HIGH_TIME/2);
- if (!ack) {
- if (!i2c_getbit()) /* receiver pulld SDA low */
- ack = 1;
- i2c_delay(CLOCK_HIGH_TIME/2);
- }
-
- /*
- * our clock is high now, make sure data is low
- * before we enable our output. If we keep data high
- * and enable output, we would generate a stop condition.
- */
-#if 0
- i2c_data(I2C_DATA_LOW);
-
- /*
- * end clock pulse
- */
- i2c_enable();
- i2c_dir_out();
-#endif
- i2c_clk(I2C_CLOCK_LOW);
- i2c_delay(CLOCK_HIGH_TIME/4);
- /*
- * enable output
- */
- i2c_dir_out();
- /*
- * remove ACK clock pulse
- */
- i2c_data(I2C_DATA_HIGH);
- i2c_delay(CLOCK_LOW_TIME/2);
- return ack;
-}
-
-/*#---------------------------------------------------------------------------
-*#
-*# FUNCTION NAME: I2C::sendAck
-*#
-*# DESCRIPTION : Send ACK on received data
-*#
-*#--------------------------------------------------------------------------*/
-void
-i2c_sendack(void)
-{
- /*
- * enable output
- */
- i2c_delay(CLOCK_LOW_TIME);
- i2c_dir_out();
- /*
- * set ack pulse high
- */
- i2c_data(I2C_DATA_LOW);
- /*
- * generate clock pulse
- */
- i2c_delay(CLOCK_HIGH_TIME/6);
- i2c_clk(I2C_CLOCK_HIGH);
- i2c_delay(CLOCK_HIGH_TIME);
- i2c_clk(I2C_CLOCK_LOW);
- i2c_delay(CLOCK_LOW_TIME/6);
- /*
- * reset data out
- */
- i2c_data(I2C_DATA_HIGH);
- i2c_delay(CLOCK_LOW_TIME);
-
- i2c_dir_in();
-}
-
-/*#---------------------------------------------------------------------------
-*#
-*# FUNCTION NAME: i2c_sendnack
-*#
-*# DESCRIPTION : Sends NACK on received data
-*#
-*#--------------------------------------------------------------------------*/
-void
-i2c_sendnack(void)
-{
- /*
- * enable output
- */
- i2c_delay(CLOCK_LOW_TIME);
- i2c_dir_out();
- /*
- * set data high
- */
- i2c_data(I2C_DATA_HIGH);
- /*
- * generate clock pulse
- */
- i2c_delay(CLOCK_HIGH_TIME/6);
- i2c_clk(I2C_CLOCK_HIGH);
- i2c_delay(CLOCK_HIGH_TIME);
- i2c_clk(I2C_CLOCK_LOW);
- i2c_delay(CLOCK_LOW_TIME);
-
- i2c_dir_in();
-}
-
-/*#---------------------------------------------------------------------------
-*#
-*# FUNCTION NAME: i2c_write
-*#
-*# DESCRIPTION : Writes a value to an I2C device
-*#
-*#--------------------------------------------------------------------------*/
-int
-i2c_write(unsigned char theSlave, void *data, size_t nbytes)
-{
- int error, cntr = 3;
- unsigned char bytes_wrote = 0;
- unsigned char value;
- unsigned long flags;
-
- spin_lock_irqsave(&i2c_lock, flags);
-
- do {
- error = 0;
-
- i2c_start();
- /*
- * send slave address
- */
- i2c_outbyte((theSlave & 0xfe));
- /*
- * wait for ack
- */
- if (!i2c_getack())
- error = 1;
- /*
- * send data
- */
- for (bytes_wrote = 0; bytes_wrote < nbytes; bytes_wrote++) {
- memcpy(&value, data + bytes_wrote, sizeof value);
- i2c_outbyte(value);
- /*
- * now it's time to wait for ack
- */
- if (!i2c_getack())
- error |= 4;
- }
- /*
- * end byte stream
- */
- i2c_stop();
-
- } while (error && cntr--);
-
- i2c_delay(CLOCK_LOW_TIME);
-
- spin_unlock_irqrestore(&i2c_lock, flags);
-
- return -error;
-}
-
-/*#---------------------------------------------------------------------------
-*#
-*# FUNCTION NAME: i2c_read
-*#
-*# DESCRIPTION : Reads a value from an I2C device
-*#
-*#--------------------------------------------------------------------------*/
-int
-i2c_read(unsigned char theSlave, void *data, size_t nbytes)
-{
- unsigned char b = 0;
- unsigned char bytes_read = 0;
- int error, cntr = 3;
- unsigned long flags;
-
- spin_lock_irqsave(&i2c_lock, flags);
-
- do {
- error = 0;
- memset(data, 0, nbytes);
- /*
- * generate start condition
- */
- i2c_start();
- /*
- * send slave address
- */
- i2c_outbyte((theSlave | 0x01));
- /*
- * wait for ack
- */
- if (!i2c_getack())
- error = 1;
- /*
- * fetch data
- */
- for (bytes_read = 0; bytes_read < nbytes; bytes_read++) {
- b = i2c_inbyte();
- memcpy(data + bytes_read, &b, sizeof b);
-
- if (bytes_read < (nbytes - 1))
- i2c_sendack();
- }
- /*
- * last received byte needs to be nacked
- * instead of acked
- */
- i2c_sendnack();
- /*
- * end sequence
- */
- i2c_stop();
- } while (error && cntr--);
-
- spin_unlock_irqrestore(&i2c_lock, flags);
-
- return -error;
-}
-
-/*#---------------------------------------------------------------------------
-*#
-*# FUNCTION NAME: i2c_writereg
-*#
-*# DESCRIPTION : Writes a value to an I2C device
-*#
-*#--------------------------------------------------------------------------*/
-int
-i2c_writereg(unsigned char theSlave, unsigned char theReg,
- unsigned char theValue)
-{
- int error, cntr = 3;
- unsigned long flags;
-
- spin_lock_irqsave(&i2c_lock, flags);
-
- do {
- error = 0;
-
- i2c_start();
- /*
- * send slave address
- */
- i2c_outbyte((theSlave & 0xfe));
- /*
- * wait for ack
- */
- if(!i2c_getack())
- error = 1;
- /*
- * now select register
- */
- i2c_dir_out();
- i2c_outbyte(theReg);
- /*
- * now it's time to wait for ack
- */
- if(!i2c_getack())
- error |= 2;
- /*
- * send register register data
- */
- i2c_outbyte(theValue);
- /*
- * now it's time to wait for ack
- */
- if(!i2c_getack())
- error |= 4;
- /*
- * end byte stream
- */
- i2c_stop();
- } while(error && cntr--);
-
- i2c_delay(CLOCK_LOW_TIME);
-
- spin_unlock_irqrestore(&i2c_lock, flags);
-
- return -error;
-}
-
-/*#---------------------------------------------------------------------------
-*#
-*# FUNCTION NAME: i2c_readreg
-*#
-*# DESCRIPTION : Reads a value from the decoder registers.
-*#
-*#--------------------------------------------------------------------------*/
-unsigned char
-i2c_readreg(unsigned char theSlave, unsigned char theReg)
-{
- unsigned char b = 0;
- int error, cntr = 3;
- unsigned long flags;
-
- spin_lock_irqsave(&i2c_lock, flags);
-
- do {
- error = 0;
- /*
- * generate start condition
- */
- i2c_start();
-
- /*
- * send slave address
- */
- i2c_outbyte((theSlave & 0xfe));
- /*
- * wait for ack
- */
- if(!i2c_getack())
- error = 1;
- /*
- * now select register
- */
- i2c_dir_out();
- i2c_outbyte(theReg);
- /*
- * now it's time to wait for ack
- */
- if(!i2c_getack())
- error |= 2;
- /*
- * repeat start condition
- */
- i2c_delay(CLOCK_LOW_TIME);
- i2c_start();
- /*
- * send slave address
- */
- i2c_outbyte(theSlave | 0x01);
- /*
- * wait for ack
- */
- if(!i2c_getack())
- error |= 4;
- /*
- * fetch register
- */
- b = i2c_inbyte();
- /*
- * last received byte needs to be nacked
- * instead of acked
- */
- i2c_sendnack();
- /*
- * end sequence
- */
- i2c_stop();
-
- } while(error && cntr--);
-
- spin_unlock_irqrestore(&i2c_lock, flags);
-
- return b;
-}
-
-static int
-i2c_open(struct inode *inode, struct file *filp)
-{
- return 0;
-}
-
-static int
-i2c_release(struct inode *inode, struct file *filp)
-{
- return 0;
-}
-
-/* Main device API. ioctl's to write or read to/from i2c registers.
- */
-
-static long
-i2c_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-{
- int ret;
- if(_IOC_TYPE(cmd) != ETRAXI2C_IOCTYPE) {
- return -ENOTTY;
- }
-
- switch (_IOC_NR(cmd)) {
- case I2C_WRITEREG:
- /* write to an i2c slave */
- D(printk("i2cw %d %d %d\n",
- I2C_ARGSLAVE(arg),
- I2C_ARGREG(arg),
- I2C_ARGVALUE(arg)));
-
- mutex_lock(&i2c_mutex);
- ret = i2c_writereg(I2C_ARGSLAVE(arg),
- I2C_ARGREG(arg),
- I2C_ARGVALUE(arg));
- mutex_unlock(&i2c_mutex);
- return ret;
-
- case I2C_READREG:
- {
- unsigned char val;
- /* read from an i2c slave */
- D(printk("i2cr %d %d ",
- I2C_ARGSLAVE(arg),
- I2C_ARGREG(arg)));
- mutex_lock(&i2c_mutex);
- val = i2c_readreg(I2C_ARGSLAVE(arg), I2C_ARGREG(arg));
- mutex_unlock(&i2c_mutex);
- D(printk("= %d\n", val));
- return val;
- }
- default:
- return -EINVAL;
-
- }
-
- return 0;
-}
-
-static const struct file_operations i2c_fops = {
- .owner = THIS_MODULE,
- .unlocked_ioctl = i2c_ioctl,
- .open = i2c_open,
- .release = i2c_release,
- .llseek = noop_llseek,
-};
-
-static int __init i2c_init(void)
-{
- static int res;
- static int first = 1;
-
- if (!first)
- return res;
-
- first = 0;
-
- /* Setup and enable the DATA and CLK pins */
-
- res = crisv32_io_get_name(&cris_i2c_data,
- CONFIG_ETRAX_V32_I2C_DATA_PORT);
- if (res < 0)
- return res;
-
- res = crisv32_io_get_name(&cris_i2c_clk, CONFIG_ETRAX_V32_I2C_CLK_PORT);
- crisv32_io_set_dir(&cris_i2c_clk, crisv32_io_dir_out);
-
- return res;
-}
-
-
-static int __init i2c_register(void)
-{
- int res;
-
- res = i2c_init();
- if (res < 0)
- return res;
-
- /* register char device */
-
- res = register_chrdev(I2C_MAJOR, i2c_name, &i2c_fops);
- if (res < 0) {
- printk(KERN_ERR "i2c: couldn't get a major number.\n");
- return res;
- }
-
- printk(KERN_INFO
- "I2C driver v2.2, (c) 1999-2007 Axis Communications AB\n");
-
- return 0;
-}
-/* this makes sure that i2c_init is called during boot */
-module_init(i2c_register);
-
-/****************** END OF FILE i2c.c ********************************/
diff --git a/kernel/arch/cris/arch-v32/drivers/i2c.h b/kernel/arch/cris/arch-v32/drivers/i2c.h
deleted file mode 100644
index d9cc856f8..000000000
--- a/kernel/arch/cris/arch-v32/drivers/i2c.h
+++ /dev/null
@@ -1,16 +0,0 @@
-
-#include <linux/init.h>
-
-/* High level I2C actions */
-int i2c_write(unsigned char theSlave, void *data, size_t nbytes);
-int i2c_read(unsigned char theSlave, void *data, size_t nbytes);
-int i2c_writereg(unsigned char theSlave, unsigned char theReg, unsigned char theValue);
-unsigned char i2c_readreg(unsigned char theSlave, unsigned char theReg);
-
-/* Low level I2C */
-void i2c_start(void);
-void i2c_stop(void);
-void i2c_outbyte(unsigned char x);
-unsigned char i2c_inbyte(void);
-int i2c_getack(void);
-void i2c_sendack(void);
diff --git a/kernel/arch/cris/arch-v32/drivers/mach-a3/Makefile b/kernel/arch/cris/arch-v32/drivers/mach-a3/Makefile
index 5c6d2a2a0..59028d0b9 100644
--- a/kernel/arch/cris/arch-v32/drivers/mach-a3/Makefile
+++ b/kernel/arch/cris/arch-v32/drivers/mach-a3/Makefile
@@ -3,4 +3,3 @@
#
obj-$(CONFIG_ETRAX_NANDFLASH) += nandflash.o
-obj-$(CONFIG_ETRAX_GPIO) += gpio.o
diff --git a/kernel/arch/cris/arch-v32/drivers/mach-a3/gpio.c b/kernel/arch/cris/arch-v32/drivers/mach-a3/gpio.c
deleted file mode 100644
index 74f9fe809..000000000
--- a/kernel/arch/cris/arch-v32/drivers/mach-a3/gpio.c
+++ /dev/null
@@ -1,999 +0,0 @@
-/*
- * Artec-3 general port I/O device
- *
- * Copyright (c) 2007 Axis Communications AB
- *
- * Authors: Bjorn Wesen (initial version)
- * Ola Knutsson (LED handling)
- * Johan Adolfsson (read/set directions, write, port G,
- * port to ETRAX FS.
- * Ricard Wanderlof (PWM for Artpec-3)
- *
- */
-
-#include <linux/module.h>
-#include <linux/sched.h>
-#include <linux/slab.h>
-#include <linux/ioport.h>
-#include <linux/errno.h>
-#include <linux/kernel.h>
-#include <linux/fs.h>
-#include <linux/string.h>
-#include <linux/poll.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/spinlock.h>
-#include <linux/mutex.h>
-
-#include <asm/etraxgpio.h>
-#include <hwregs/reg_map.h>
-#include <hwregs/reg_rdwr.h>
-#include <hwregs/gio_defs.h>
-#include <hwregs/intr_vect_defs.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <mach/pinmux.h>
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-#include "../i2c.h"
-
-#define VIRT_I2C_ADDR 0x40
-#endif
-
-/* The following gio ports on ARTPEC-3 is available:
- * pa 32 bits
- * pb 32 bits
- * pc 16 bits
- * each port has a rw_px_dout, r_px_din and rw_px_oe register.
- */
-
-#define GPIO_MAJOR 120 /* experimental MAJOR number */
-
-#define I2C_INTERRUPT_BITS 0x300 /* i2c0_done and i2c1_done bits */
-
-#define D(x)
-
-#if 0
-static int dp_cnt;
-#define DP(x) \
- do { \
- dp_cnt++; \
- if (dp_cnt % 1000 == 0) \
- x; \
- } while (0)
-#else
-#define DP(x)
-#endif
-
-static DEFINE_MUTEX(gpio_mutex);
-static char gpio_name[] = "etrax gpio";
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static int virtual_gpio_ioctl(struct file *file, unsigned int cmd,
- unsigned long arg);
-#endif
-static long gpio_ioctl(struct file *file, unsigned int cmd, unsigned long arg);
-static ssize_t gpio_write(struct file *file, const char __user *buf,
- size_t count, loff_t *off);
-static int gpio_open(struct inode *inode, struct file *filp);
-static int gpio_release(struct inode *inode, struct file *filp);
-static unsigned int gpio_poll(struct file *filp,
- struct poll_table_struct *wait);
-
-/* private data per open() of this driver */
-
-struct gpio_private {
- struct gpio_private *next;
- /* The IO_CFG_WRITE_MODE_VALUE only support 8 bits: */
- unsigned char clk_mask;
- unsigned char data_mask;
- unsigned char write_msb;
- unsigned char pad1;
- /* These fields are generic */
- unsigned long highalarm, lowalarm;
- wait_queue_head_t alarm_wq;
- int minor;
-};
-
-static void gpio_set_alarm(struct gpio_private *priv);
-static int gpio_leds_ioctl(unsigned int cmd, unsigned long arg);
-static int gpio_pwm_ioctl(struct gpio_private *priv, unsigned int cmd,
- unsigned long arg);
-
-
-/* linked list of alarms to check for */
-
-static struct gpio_private *alarmlist;
-
-static int wanted_interrupts;
-
-static DEFINE_SPINLOCK(gpio_lock);
-
-#define NUM_PORTS (GPIO_MINOR_LAST+1)
-#define GIO_REG_RD_ADDR(reg) \
- (unsigned long *)(regi_gio + REG_RD_ADDR_gio_##reg)
-#define GIO_REG_WR_ADDR(reg) \
- (unsigned long *)(regi_gio + REG_WR_ADDR_gio_##reg)
-static unsigned long led_dummy;
-static unsigned long port_d_dummy; /* Only input on Artpec-3 */
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static unsigned long port_e_dummy; /* Non existent on Artpec-3 */
-static unsigned long virtual_dummy;
-static unsigned long virtual_rw_pv_oe = CONFIG_ETRAX_DEF_GIO_PV_OE;
-static unsigned short cached_virtual_gpio_read;
-#endif
-
-static unsigned long *data_out[NUM_PORTS] = {
- GIO_REG_WR_ADDR(rw_pa_dout),
- GIO_REG_WR_ADDR(rw_pb_dout),
- &led_dummy,
- GIO_REG_WR_ADDR(rw_pc_dout),
- &port_d_dummy,
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- &port_e_dummy,
- &virtual_dummy,
-#endif
-};
-
-static unsigned long *data_in[NUM_PORTS] = {
- GIO_REG_RD_ADDR(r_pa_din),
- GIO_REG_RD_ADDR(r_pb_din),
- &led_dummy,
- GIO_REG_RD_ADDR(r_pc_din),
- GIO_REG_RD_ADDR(r_pd_din),
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- &port_e_dummy,
- &virtual_dummy,
-#endif
-};
-
-static unsigned long changeable_dir[NUM_PORTS] = {
- CONFIG_ETRAX_PA_CHANGEABLE_DIR,
- CONFIG_ETRAX_PB_CHANGEABLE_DIR,
- 0,
- CONFIG_ETRAX_PC_CHANGEABLE_DIR,
- 0,
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- 0,
- CONFIG_ETRAX_PV_CHANGEABLE_DIR,
-#endif
-};
-
-static unsigned long changeable_bits[NUM_PORTS] = {
- CONFIG_ETRAX_PA_CHANGEABLE_BITS,
- CONFIG_ETRAX_PB_CHANGEABLE_BITS,
- 0,
- CONFIG_ETRAX_PC_CHANGEABLE_BITS,
- 0,
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- 0,
- CONFIG_ETRAX_PV_CHANGEABLE_BITS,
-#endif
-};
-
-static unsigned long *dir_oe[NUM_PORTS] = {
- GIO_REG_WR_ADDR(rw_pa_oe),
- GIO_REG_WR_ADDR(rw_pb_oe),
- &led_dummy,
- GIO_REG_WR_ADDR(rw_pc_oe),
- &port_d_dummy,
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- &port_e_dummy,
- &virtual_rw_pv_oe,
-#endif
-};
-
-static void gpio_set_alarm(struct gpio_private *priv)
-{
- int bit;
- int intr_cfg;
- int mask;
- int pins;
- unsigned long flags;
-
- spin_lock_irqsave(&gpio_lock, flags);
- intr_cfg = REG_RD_INT(gio, regi_gio, rw_intr_cfg);
- pins = REG_RD_INT(gio, regi_gio, rw_intr_pins);
- mask = REG_RD_INT(gio, regi_gio, rw_intr_mask) & I2C_INTERRUPT_BITS;
-
- for (bit = 0; bit < 32; bit++) {
- int intr = bit % 8;
- int pin = bit / 8;
- if (priv->minor < GPIO_MINOR_LEDS)
- pin += priv->minor * 4;
- else
- pin += (priv->minor - 1) * 4;
-
- if (priv->highalarm & (1<<bit)) {
- intr_cfg |= (regk_gio_hi << (intr * 3));
- mask |= 1 << intr;
- wanted_interrupts = mask & 0xff;
- pins |= pin << (intr * 4);
- } else if (priv->lowalarm & (1<<bit)) {
- intr_cfg |= (regk_gio_lo << (intr * 3));
- mask |= 1 << intr;
- wanted_interrupts = mask & 0xff;
- pins |= pin << (intr * 4);
- }
- }
-
- REG_WR_INT(gio, regi_gio, rw_intr_cfg, intr_cfg);
- REG_WR_INT(gio, regi_gio, rw_intr_pins, pins);
- REG_WR_INT(gio, regi_gio, rw_intr_mask, mask);
-
- spin_unlock_irqrestore(&gpio_lock, flags);
-}
-
-static unsigned int gpio_poll(struct file *file, struct poll_table_struct *wait)
-{
- unsigned int mask = 0;
- struct gpio_private *priv = file->private_data;
- unsigned long data;
- unsigned long tmp;
-
- if (priv->minor >= GPIO_MINOR_PWM0 &&
- priv->minor <= GPIO_MINOR_LAST_PWM)
- return 0;
-
- poll_wait(file, &priv->alarm_wq, wait);
- if (priv->minor <= GPIO_MINOR_D) {
- data = readl(data_in[priv->minor]);
- REG_WR_INT(gio, regi_gio, rw_ack_intr, wanted_interrupts);
- tmp = REG_RD_INT(gio, regi_gio, rw_intr_mask);
- tmp &= I2C_INTERRUPT_BITS;
- tmp |= wanted_interrupts;
- REG_WR_INT(gio, regi_gio, rw_intr_mask, tmp);
- } else
- return 0;
-
- if ((data & priv->highalarm) || (~data & priv->lowalarm))
- mask = POLLIN|POLLRDNORM;
-
- DP(printk(KERN_DEBUG "gpio_poll ready: mask 0x%08X\n", mask));
- return mask;
-}
-
-static irqreturn_t gpio_interrupt(int irq, void *dev_id)
-{
- reg_gio_rw_intr_mask intr_mask;
- reg_gio_r_masked_intr masked_intr;
- reg_gio_rw_ack_intr ack_intr;
- unsigned long flags;
- unsigned long tmp;
- unsigned long tmp2;
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- unsigned char enable_gpiov_ack = 0;
-#endif
-
- /* Find what PA interrupts are active */
- masked_intr = REG_RD(gio, regi_gio, r_masked_intr);
- tmp = REG_TYPE_CONV(unsigned long, reg_gio_r_masked_intr, masked_intr);
-
- /* Find those that we have enabled */
- spin_lock_irqsave(&gpio_lock, flags);
- tmp &= wanted_interrupts;
- spin_unlock_irqrestore(&gpio_lock, flags);
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- /* Something changed on virtual GPIO. Interrupt is acked by
- * reading the device.
- */
- if (tmp & (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN)) {
- i2c_read(VIRT_I2C_ADDR, (void *)&cached_virtual_gpio_read,
- sizeof(cached_virtual_gpio_read));
- enable_gpiov_ack = 1;
- }
-#endif
-
- /* Ack them */
- ack_intr = REG_TYPE_CONV(reg_gio_rw_ack_intr, unsigned long, tmp);
- REG_WR(gio, regi_gio, rw_ack_intr, ack_intr);
-
- /* Disable those interrupts.. */
- intr_mask = REG_RD(gio, regi_gio, rw_intr_mask);
- tmp2 = REG_TYPE_CONV(unsigned long, reg_gio_rw_intr_mask, intr_mask);
- tmp2 &= ~tmp;
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- /* Do not disable interrupt on virtual GPIO. Changes on virtual
- * pins are only noticed by an interrupt.
- */
- if (enable_gpiov_ack)
- tmp2 |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
-#endif
- intr_mask = REG_TYPE_CONV(reg_gio_rw_intr_mask, unsigned long, tmp2);
- REG_WR(gio, regi_gio, rw_intr_mask, intr_mask);
-
- return IRQ_RETVAL(tmp);
-}
-
-static void gpio_write_bit(unsigned long *port, unsigned char data, int bit,
- unsigned char clk_mask, unsigned char data_mask)
-{
- unsigned long shadow = readl(port) & ~clk_mask;
- writel(shadow, port);
- if (data & 1 << bit)
- shadow |= data_mask;
- else
- shadow &= ~data_mask;
- writel(shadow, port);
- /* For FPGA: min 5.0ns (DCC) before CCLK high */
- shadow |= clk_mask;
- writel(shadow, port);
-}
-
-static void gpio_write_byte(struct gpio_private *priv, unsigned long *port,
- unsigned char data)
-{
- int i;
-
- if (priv->write_msb)
- for (i = 7; i >= 0; i--)
- gpio_write_bit(port, data, i, priv->clk_mask,
- priv->data_mask);
- else
- for (i = 0; i <= 7; i++)
- gpio_write_bit(port, data, i, priv->clk_mask,
- priv->data_mask);
-}
-
-
-static ssize_t gpio_write(struct file *file, const char __user *buf,
- size_t count, loff_t *off)
-{
- struct gpio_private *priv = file->private_data;
- unsigned long flags;
- ssize_t retval = count;
- /* Only bits 0-7 may be used for write operations but allow all
- devices except leds... */
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- if (priv->minor == GPIO_MINOR_V)
- return -EFAULT;
-#endif
- if (priv->minor == GPIO_MINOR_LEDS)
- return -EFAULT;
-
- if (priv->minor >= GPIO_MINOR_PWM0 &&
- priv->minor <= GPIO_MINOR_LAST_PWM)
- return -EFAULT;
-
- if (!access_ok(VERIFY_READ, buf, count))
- return -EFAULT;
-
- /* It must have been configured using the IO_CFG_WRITE_MODE */
- /* Perhaps a better error code? */
- if (priv->clk_mask == 0 || priv->data_mask == 0)
- return -EPERM;
-
- D(printk(KERN_DEBUG "gpio_write: %lu to data 0x%02X clk 0x%02X "
- "msb: %i\n",
- count, priv->data_mask, priv->clk_mask, priv->write_msb));
-
- spin_lock_irqsave(&gpio_lock, flags);
-
- while (count--)
- gpio_write_byte(priv, data_out[priv->minor], *buf++);
-
- spin_unlock_irqrestore(&gpio_lock, flags);
- return retval;
-}
-
-static int gpio_open(struct inode *inode, struct file *filp)
-{
- struct gpio_private *priv;
- int p = iminor(inode);
-
- if (p > GPIO_MINOR_LAST_PWM ||
- (p > GPIO_MINOR_LAST && p < GPIO_MINOR_PWM0))
- return -EINVAL;
-
- priv = kmalloc(sizeof(struct gpio_private), GFP_KERNEL);
-
- if (!priv)
- return -ENOMEM;
-
- mutex_lock(&gpio_mutex);
- memset(priv, 0, sizeof(*priv));
-
- priv->minor = p;
- filp->private_data = priv;
-
- /* initialize the io/alarm struct, not for PWM ports though */
- if (p <= GPIO_MINOR_LAST) {
-
- priv->clk_mask = 0;
- priv->data_mask = 0;
- priv->highalarm = 0;
- priv->lowalarm = 0;
-
- init_waitqueue_head(&priv->alarm_wq);
-
- /* link it into our alarmlist */
- spin_lock_irq(&gpio_lock);
- priv->next = alarmlist;
- alarmlist = priv;
- spin_unlock_irq(&gpio_lock);
- }
-
- mutex_unlock(&gpio_mutex);
- return 0;
-}
-
-static int gpio_release(struct inode *inode, struct file *filp)
-{
- struct gpio_private *p;
- struct gpio_private *todel;
- /* local copies while updating them: */
- unsigned long a_high, a_low;
-
- /* prepare to free private structure */
- todel = filp->private_data;
-
- /* unlink from alarmlist - only for non-PWM ports though */
- if (todel->minor <= GPIO_MINOR_LAST) {
- spin_lock_irq(&gpio_lock);
- p = alarmlist;
-
- if (p == todel)
- alarmlist = todel->next;
- else {
- while (p->next != todel)
- p = p->next;
- p->next = todel->next;
- }
-
- /* Check if there are still any alarms set */
- p = alarmlist;
- a_high = 0;
- a_low = 0;
- while (p) {
- if (p->minor == GPIO_MINOR_A) {
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- p->lowalarm |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
-#endif
- a_high |= p->highalarm;
- a_low |= p->lowalarm;
- }
-
- p = p->next;
- }
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- /* Variable 'a_low' needs to be set here again
- * to ensure that interrupt for virtual GPIO is handled.
- */
- a_low |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
-#endif
-
- spin_unlock_irq(&gpio_lock);
- }
- kfree(todel);
-
- return 0;
-}
-
-/* Main device API. ioctl's to read/set/clear bits, as well as to
- * set alarms to wait for using a subsequent select().
- */
-
-inline unsigned long setget_input(struct gpio_private *priv, unsigned long arg)
-{
- /* Set direction 0=unchanged 1=input,
- * return mask with 1=input
- */
- unsigned long flags;
- unsigned long dir_shadow;
-
- spin_lock_irqsave(&gpio_lock, flags);
-
- dir_shadow = readl(dir_oe[priv->minor]) &
- ~(arg & changeable_dir[priv->minor]);
- writel(dir_shadow, dir_oe[priv->minor]);
-
- spin_unlock_irqrestore(&gpio_lock, flags);
-
- if (priv->minor == GPIO_MINOR_C)
- dir_shadow ^= 0xFFFF; /* Only 16 bits */
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- else if (priv->minor == GPIO_MINOR_V)
- dir_shadow ^= 0xFFFF; /* Only 16 bits */
-#endif
- else
- dir_shadow ^= 0xFFFFFFFF; /* PA, PB and PD 32 bits */
-
- return dir_shadow;
-
-} /* setget_input */
-
-static inline unsigned long setget_output(struct gpio_private *priv,
- unsigned long arg)
-{
- unsigned long flags;
- unsigned long dir_shadow;
-
- spin_lock_irqsave(&gpio_lock, flags);
-
- dir_shadow = readl(dir_oe[priv->minor]) |
- (arg & changeable_dir[priv->minor]);
- writel(dir_shadow, dir_oe[priv->minor]);
-
- spin_unlock_irqrestore(&gpio_lock, flags);
- return dir_shadow;
-} /* setget_output */
-
-static long gpio_ioctl_unlocked(struct file *file,
- unsigned int cmd, unsigned long arg)
-{
- unsigned long flags;
- unsigned long val;
- unsigned long shadow;
- struct gpio_private *priv = file->private_data;
-
- if (_IOC_TYPE(cmd) != ETRAXGPIO_IOCTYPE)
- return -ENOTTY;
-
- /* Check for special ioctl handlers first */
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- if (priv->minor == GPIO_MINOR_V)
- return virtual_gpio_ioctl(file, cmd, arg);
-#endif
-
- if (priv->minor == GPIO_MINOR_LEDS)
- return gpio_leds_ioctl(cmd, arg);
-
- if (priv->minor >= GPIO_MINOR_PWM0 &&
- priv->minor <= GPIO_MINOR_LAST_PWM)
- return gpio_pwm_ioctl(priv, cmd, arg);
-
- switch (_IOC_NR(cmd)) {
- case IO_READBITS: /* Use IO_READ_INBITS and IO_READ_OUTBITS instead */
- /* Read the port. */
- return readl(data_in[priv->minor]);
- case IO_SETBITS:
- spin_lock_irqsave(&gpio_lock, flags);
- /* Set changeable bits with a 1 in arg. */
- shadow = readl(data_out[priv->minor]) |
- (arg & changeable_bits[priv->minor]);
- writel(shadow, data_out[priv->minor]);
- spin_unlock_irqrestore(&gpio_lock, flags);
- break;
- case IO_CLRBITS:
- spin_lock_irqsave(&gpio_lock, flags);
- /* Clear changeable bits with a 1 in arg. */
- shadow = readl(data_out[priv->minor]) &
- ~(arg & changeable_bits[priv->minor]);
- writel(shadow, data_out[priv->minor]);
- spin_unlock_irqrestore(&gpio_lock, flags);
- break;
- case IO_HIGHALARM:
- /* Set alarm when bits with 1 in arg go high. */
- priv->highalarm |= arg;
- gpio_set_alarm(priv);
- break;
- case IO_LOWALARM:
- /* Set alarm when bits with 1 in arg go low. */
- priv->lowalarm |= arg;
- gpio_set_alarm(priv);
- break;
- case IO_CLRALARM:
- /* Clear alarm for bits with 1 in arg. */
- priv->highalarm &= ~arg;
- priv->lowalarm &= ~arg;
- gpio_set_alarm(priv);
- break;
- case IO_READDIR: /* Use IO_SETGET_INPUT/OUTPUT instead! */
- /* Read direction 0=input 1=output */
- return readl(dir_oe[priv->minor]);
-
- case IO_SETINPUT: /* Use IO_SETGET_INPUT instead! */
- /* Set direction 0=unchanged 1=input,
- * return mask with 1=input
- */
- return setget_input(priv, arg);
-
- case IO_SETOUTPUT: /* Use IO_SETGET_OUTPUT instead! */
- /* Set direction 0=unchanged 1=output,
- * return mask with 1=output
- */
- return setget_output(priv, arg);
-
- case IO_CFG_WRITE_MODE:
- {
- int res = -EPERM;
- unsigned long dir_shadow, clk_mask, data_mask, write_msb;
-
- clk_mask = arg & 0xFF;
- data_mask = (arg >> 8) & 0xFF;
- write_msb = (arg >> 16) & 0x01;
-
- /* Check if we're allowed to change the bits and
- * the direction is correct
- */
- spin_lock_irqsave(&gpio_lock, flags);
- dir_shadow = readl(dir_oe[priv->minor]);
- if ((clk_mask & changeable_bits[priv->minor]) &&
- (data_mask & changeable_bits[priv->minor]) &&
- (clk_mask & dir_shadow) &&
- (data_mask & dir_shadow)) {
- priv->clk_mask = clk_mask;
- priv->data_mask = data_mask;
- priv->write_msb = write_msb;
- res = 0;
- }
- spin_unlock_irqrestore(&gpio_lock, flags);
-
- return res;
- }
- case IO_READ_INBITS:
- /* *arg is result of reading the input pins */
- val = readl(data_in[priv->minor]);
- if (copy_to_user((void __user *)arg, &val, sizeof(val)))
- return -EFAULT;
- return 0;
- case IO_READ_OUTBITS:
- /* *arg is result of reading the output shadow */
- val = *data_out[priv->minor];
- if (copy_to_user((void __user *)arg, &val, sizeof(val)))
- return -EFAULT;
- break;
- case IO_SETGET_INPUT:
- /* bits set in *arg is set to input,
- * *arg updated with current input pins.
- */
- if (copy_from_user(&val, (void __user *)arg, sizeof(val)))
- return -EFAULT;
- val = setget_input(priv, val);
- if (copy_to_user((void __user *)arg, &val, sizeof(val)))
- return -EFAULT;
- break;
- case IO_SETGET_OUTPUT:
- /* bits set in *arg is set to output,
- * *arg updated with current output pins.
- */
- if (copy_from_user(&val, (void __user *)arg, sizeof(val)))
- return -EFAULT;
- val = setget_output(priv, val);
- if (copy_to_user((void __user *)arg, &val, sizeof(val)))
- return -EFAULT;
- break;
- default:
- return -EINVAL;
- } /* switch */
-
- return 0;
-}
-
-static long gpio_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-{
- long ret;
-
- mutex_lock(&gpio_mutex);
- ret = gpio_ioctl_unlocked(file, cmd, arg);
- mutex_unlock(&gpio_mutex);
-
- return ret;
-}
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static int virtual_gpio_ioctl(struct file *file, unsigned int cmd,
- unsigned long arg)
-{
- unsigned long flags;
- unsigned short val;
- unsigned short shadow;
- struct gpio_private *priv = file->private_data;
-
- switch (_IOC_NR(cmd)) {
- case IO_SETBITS:
- spin_lock_irqsave(&gpio_lock, flags);
- /* Set changeable bits with a 1 in arg. */
- i2c_read(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
- shadow |= ~readl(dir_oe[priv->minor]) |
- (arg & changeable_bits[priv->minor]);
- i2c_write(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
- spin_unlock_irqrestore(&gpio_lock, flags);
- break;
- case IO_CLRBITS:
- spin_lock_irqsave(&gpio_lock, flags);
- /* Clear changeable bits with a 1 in arg. */
- i2c_read(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
- shadow |= ~readl(dir_oe[priv->minor]) &
- ~(arg & changeable_bits[priv->minor]);
- i2c_write(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
- spin_unlock_irqrestore(&gpio_lock, flags);
- break;
- case IO_HIGHALARM:
- /* Set alarm when bits with 1 in arg go high. */
- priv->highalarm |= arg;
- break;
- case IO_LOWALARM:
- /* Set alarm when bits with 1 in arg go low. */
- priv->lowalarm |= arg;
- break;
- case IO_CLRALARM:
- /* Clear alarm for bits with 1 in arg. */
- priv->highalarm &= ~arg;
- priv->lowalarm &= ~arg;
- break;
- case IO_CFG_WRITE_MODE:
- {
- unsigned long dir_shadow;
- dir_shadow = readl(dir_oe[priv->minor]);
-
- priv->clk_mask = arg & 0xFF;
- priv->data_mask = (arg >> 8) & 0xFF;
- priv->write_msb = (arg >> 16) & 0x01;
- /* Check if we're allowed to change the bits and
- * the direction is correct
- */
- if (!((priv->clk_mask & changeable_bits[priv->minor]) &&
- (priv->data_mask & changeable_bits[priv->minor]) &&
- (priv->clk_mask & dir_shadow) &&
- (priv->data_mask & dir_shadow))) {
- priv->clk_mask = 0;
- priv->data_mask = 0;
- return -EPERM;
- }
- break;
- }
- case IO_READ_INBITS:
- /* *arg is result of reading the input pins */
- val = cached_virtual_gpio_read & ~readl(dir_oe[priv->minor]);
- if (copy_to_user((void __user *)arg, &val, sizeof(val)))
- return -EFAULT;
- return 0;
-
- case IO_READ_OUTBITS:
- /* *arg is result of reading the output shadow */
- i2c_read(VIRT_I2C_ADDR, (void *)&val, sizeof(val));
- val &= readl(dir_oe[priv->minor]);
- if (copy_to_user((void __user *)arg, &val, sizeof(val)))
- return -EFAULT;
- break;
- case IO_SETGET_INPUT:
- {
- /* bits set in *arg is set to input,
- * *arg updated with current input pins.
- */
- unsigned short input_mask = ~readl(dir_oe[priv->minor]);
- if (copy_from_user(&val, (void __user *)arg, sizeof(val)))
- return -EFAULT;
- val = setget_input(priv, val);
- if (copy_to_user((void __user *)arg, &val, sizeof(val)))
- return -EFAULT;
- if ((input_mask & val) != input_mask) {
- /* Input pins changed. All ports desired as input
- * should be set to logic 1.
- */
- unsigned short change = input_mask ^ val;
- i2c_read(VIRT_I2C_ADDR, (void *)&shadow,
- sizeof(shadow));
- shadow &= ~change;
- shadow |= val;
- i2c_write(VIRT_I2C_ADDR, (void *)&shadow,
- sizeof(shadow));
- }
- break;
- }
- case IO_SETGET_OUTPUT:
- /* bits set in *arg is set to output,
- * *arg updated with current output pins.
- */
- if (copy_from_user(&val, (void __user *)arg, sizeof(val)))
- return -EFAULT;
- val = setget_output(priv, val);
- if (copy_to_user((void __user *)arg, &val, sizeof(val)))
- return -EFAULT;
- break;
- default:
- return -EINVAL;
- } /* switch */
- return 0;
-}
-#endif /* CONFIG_ETRAX_VIRTUAL_GPIO */
-
-static int gpio_leds_ioctl(unsigned int cmd, unsigned long arg)
-{
- unsigned char green;
- unsigned char red;
-
- switch (_IOC_NR(cmd)) {
- case IO_LEDACTIVE_SET:
- green = ((unsigned char) arg) & 1;
- red = (((unsigned char) arg) >> 1) & 1;
- CRIS_LED_ACTIVE_SET_G(green);
- CRIS_LED_ACTIVE_SET_R(red);
- break;
-
- default:
- return -EINVAL;
- } /* switch */
-
- return 0;
-}
-
-static int gpio_pwm_set_mode(unsigned long arg, int pwm_port)
-{
- int pinmux_pwm = pinmux_pwm0 + pwm_port;
- int mode;
- reg_gio_rw_pwm0_ctrl rw_pwm_ctrl = {
- .ccd_val = 0,
- .ccd_override = regk_gio_no,
- .mode = regk_gio_no
- };
- int allocstatus;
-
- if (get_user(mode, &((struct io_pwm_set_mode *) arg)->mode))
- return -EFAULT;
- rw_pwm_ctrl.mode = mode;
- if (mode != PWM_OFF)
- allocstatus = crisv32_pinmux_alloc_fixed(pinmux_pwm);
- else
- allocstatus = crisv32_pinmux_dealloc_fixed(pinmux_pwm);
- if (allocstatus)
- return allocstatus;
- REG_WRITE(reg_gio_rw_pwm0_ctrl, REG_ADDR(gio, regi_gio, rw_pwm0_ctrl) +
- 12 * pwm_port, rw_pwm_ctrl);
- return 0;
-}
-
-static int gpio_pwm_set_period(unsigned long arg, int pwm_port)
-{
- struct io_pwm_set_period periods;
- reg_gio_rw_pwm0_var rw_pwm_widths;
-
- if (copy_from_user(&periods, (void __user *)arg, sizeof(periods)))
- return -EFAULT;
- if (periods.lo > 8191 || periods.hi > 8191)
- return -EINVAL;
- rw_pwm_widths.lo = periods.lo;
- rw_pwm_widths.hi = periods.hi;
- REG_WRITE(reg_gio_rw_pwm0_var, REG_ADDR(gio, regi_gio, rw_pwm0_var) +
- 12 * pwm_port, rw_pwm_widths);
- return 0;
-}
-
-static int gpio_pwm_set_duty(unsigned long arg, int pwm_port)
-{
- unsigned int duty;
- reg_gio_rw_pwm0_data rw_pwm_duty;
-
- if (get_user(duty, &((struct io_pwm_set_duty *) arg)->duty))
- return -EFAULT;
- if (duty > 255)
- return -EINVAL;
- rw_pwm_duty.data = duty;
- REG_WRITE(reg_gio_rw_pwm0_data, REG_ADDR(gio, regi_gio, rw_pwm0_data) +
- 12 * pwm_port, rw_pwm_duty);
- return 0;
-}
-
-static int gpio_pwm_ioctl(struct gpio_private *priv, unsigned int cmd,
- unsigned long arg)
-{
- int pwm_port = priv->minor - GPIO_MINOR_PWM0;
-
- switch (_IOC_NR(cmd)) {
- case IO_PWM_SET_MODE:
- return gpio_pwm_set_mode(arg, pwm_port);
- case IO_PWM_SET_PERIOD:
- return gpio_pwm_set_period(arg, pwm_port);
- case IO_PWM_SET_DUTY:
- return gpio_pwm_set_duty(arg, pwm_port);
- default:
- return -EINVAL;
- }
- return 0;
-}
-
-static const struct file_operations gpio_fops = {
- .owner = THIS_MODULE,
- .poll = gpio_poll,
- .unlocked_ioctl = gpio_ioctl,
- .write = gpio_write,
- .open = gpio_open,
- .release = gpio_release,
- .llseek = noop_llseek,
-};
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static void __init virtual_gpio_init(void)
-{
- reg_gio_rw_intr_cfg intr_cfg;
- reg_gio_rw_intr_mask intr_mask;
- unsigned short shadow;
-
- shadow = ~virtual_rw_pv_oe; /* Input ports should be set to logic 1 */
- shadow |= CONFIG_ETRAX_DEF_GIO_PV_OUT;
- i2c_write(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
-
- /* Set interrupt mask and on what state the interrupt shall trigger.
- * For virtual gpio the interrupt shall trigger on logic '0'.
- */
- intr_cfg = REG_RD(gio, regi_gio, rw_intr_cfg);
- intr_mask = REG_RD(gio, regi_gio, rw_intr_mask);
-
- switch (CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN) {
- case 0:
- intr_cfg.pa0 = regk_gio_lo;
- intr_mask.pa0 = regk_gio_yes;
- break;
- case 1:
- intr_cfg.pa1 = regk_gio_lo;
- intr_mask.pa1 = regk_gio_yes;
- break;
- case 2:
- intr_cfg.pa2 = regk_gio_lo;
- intr_mask.pa2 = regk_gio_yes;
- break;
- case 3:
- intr_cfg.pa3 = regk_gio_lo;
- intr_mask.pa3 = regk_gio_yes;
- break;
- case 4:
- intr_cfg.pa4 = regk_gio_lo;
- intr_mask.pa4 = regk_gio_yes;
- break;
- case 5:
- intr_cfg.pa5 = regk_gio_lo;
- intr_mask.pa5 = regk_gio_yes;
- break;
- case 6:
- intr_cfg.pa6 = regk_gio_lo;
- intr_mask.pa6 = regk_gio_yes;
- break;
- case 7:
- intr_cfg.pa7 = regk_gio_lo;
- intr_mask.pa7 = regk_gio_yes;
- break;
- }
-
- REG_WR(gio, regi_gio, rw_intr_cfg, intr_cfg);
- REG_WR(gio, regi_gio, rw_intr_mask, intr_mask);
-}
-#endif
-
-/* main driver initialization routine, called from mem.c */
-
-static int __init gpio_init(void)
-{
- int res;
-
- printk(KERN_INFO "ETRAX FS GPIO driver v2.7, (c) 2003-2008 "
- "Axis Communications AB\n");
-
- /* do the formalities */
-
- res = register_chrdev(GPIO_MAJOR, gpio_name, &gpio_fops);
- if (res < 0) {
- printk(KERN_ERR "gpio: couldn't get a major number.\n");
- return res;
- }
-
- /* Clear all leds */
- CRIS_LED_NETWORK_GRP0_SET(0);
- CRIS_LED_NETWORK_GRP1_SET(0);
- CRIS_LED_ACTIVE_SET(0);
- CRIS_LED_DISK_READ(0);
- CRIS_LED_DISK_WRITE(0);
-
- int res2 = request_irq(GIO_INTR_VECT, gpio_interrupt,
- IRQF_SHARED, "gpio", &alarmlist);
- if (res2) {
- printk(KERN_ERR "err: irq for gpio\n");
- return res2;
- }
-
- /* No IRQs by default. */
- REG_WR_INT(gio, regi_gio, rw_intr_pins, 0);
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- virtual_gpio_init();
-#endif
-
- return res;
-}
-
-/* this makes sure that gpio_init is called during kernel boot */
-
-module_init(gpio_init);
diff --git a/kernel/arch/cris/arch-v32/drivers/mach-fs/Makefile b/kernel/arch/cris/arch-v32/drivers/mach-fs/Makefile
index 5c6d2a2a0..59028d0b9 100644
--- a/kernel/arch/cris/arch-v32/drivers/mach-fs/Makefile
+++ b/kernel/arch/cris/arch-v32/drivers/mach-fs/Makefile
@@ -3,4 +3,3 @@
#
obj-$(CONFIG_ETRAX_NANDFLASH) += nandflash.o
-obj-$(CONFIG_ETRAX_GPIO) += gpio.o
diff --git a/kernel/arch/cris/arch-v32/drivers/mach-fs/gpio.c b/kernel/arch/cris/arch-v32/drivers/mach-fs/gpio.c
deleted file mode 100644
index 009f4ee1b..000000000
--- a/kernel/arch/cris/arch-v32/drivers/mach-fs/gpio.c
+++ /dev/null
@@ -1,979 +0,0 @@
-/*
- * ETRAX CRISv32 general port I/O device
- *
- * Copyright (c) 1999-2006 Axis Communications AB
- *
- * Authors: Bjorn Wesen (initial version)
- * Ola Knutsson (LED handling)
- * Johan Adolfsson (read/set directions, write, port G,
- * port to ETRAX FS.
- *
- */
-
-#include <linux/module.h>
-#include <linux/sched.h>
-#include <linux/slab.h>
-#include <linux/ioport.h>
-#include <linux/errno.h>
-#include <linux/kernel.h>
-#include <linux/fs.h>
-#include <linux/string.h>
-#include <linux/poll.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/spinlock.h>
-#include <linux/mutex.h>
-
-#include <asm/etraxgpio.h>
-#include <hwregs/reg_map.h>
-#include <hwregs/reg_rdwr.h>
-#include <hwregs/gio_defs.h>
-#include <hwregs/intr_vect_defs.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-#include "../i2c.h"
-
-#define VIRT_I2C_ADDR 0x40
-#endif
-
-/* The following gio ports on ETRAX FS is available:
- * pa 8 bits, supports interrupts off, hi, low, set, posedge, negedge anyedge
- * pb 18 bits
- * pc 18 bits
- * pd 18 bits
- * pe 18 bits
- * each port has a rw_px_dout, r_px_din and rw_px_oe register.
- */
-
-#define GPIO_MAJOR 120 /* experimental MAJOR number */
-
-#define D(x)
-
-#if 0
-static int dp_cnt;
-#define DP(x) \
- do { \
- dp_cnt++; \
- if (dp_cnt % 1000 == 0) \
- x; \
- } while (0)
-#else
-#define DP(x)
-#endif
-
-static DEFINE_MUTEX(gpio_mutex);
-static char gpio_name[] = "etrax gpio";
-
-#if 0
-static wait_queue_head_t *gpio_wq;
-#endif
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static int virtual_gpio_ioctl(struct file *file, unsigned int cmd,
- unsigned long arg);
-#endif
-static long gpio_ioctl(struct file *file, unsigned int cmd, unsigned long arg);
-static ssize_t gpio_write(struct file *file, const char *buf, size_t count,
- loff_t *off);
-static int gpio_open(struct inode *inode, struct file *filp);
-static int gpio_release(struct inode *inode, struct file *filp);
-static unsigned int gpio_poll(struct file *filp,
- struct poll_table_struct *wait);
-
-/* private data per open() of this driver */
-
-struct gpio_private {
- struct gpio_private *next;
- /* The IO_CFG_WRITE_MODE_VALUE only support 8 bits: */
- unsigned char clk_mask;
- unsigned char data_mask;
- unsigned char write_msb;
- unsigned char pad1;
- /* These fields are generic */
- unsigned long highalarm, lowalarm;
- wait_queue_head_t alarm_wq;
- int minor;
-};
-
-/* linked list of alarms to check for */
-
-static struct gpio_private *alarmlist;
-
-static int gpio_some_alarms; /* Set if someone uses alarm */
-static unsigned long gpio_pa_high_alarms;
-static unsigned long gpio_pa_low_alarms;
-
-static DEFINE_SPINLOCK(alarm_lock);
-
-#define NUM_PORTS (GPIO_MINOR_LAST+1)
-#define GIO_REG_RD_ADDR(reg) \
- (volatile unsigned long *)(regi_gio + REG_RD_ADDR_gio_##reg)
-#define GIO_REG_WR_ADDR(reg) \
- (volatile unsigned long *)(regi_gio + REG_RD_ADDR_gio_##reg)
-unsigned long led_dummy;
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static unsigned long virtual_dummy;
-static unsigned long virtual_rw_pv_oe = CONFIG_ETRAX_DEF_GIO_PV_OE;
-static unsigned short cached_virtual_gpio_read;
-#endif
-
-static volatile unsigned long *data_out[NUM_PORTS] = {
- GIO_REG_WR_ADDR(rw_pa_dout),
- GIO_REG_WR_ADDR(rw_pb_dout),
- &led_dummy,
- GIO_REG_WR_ADDR(rw_pc_dout),
- GIO_REG_WR_ADDR(rw_pd_dout),
- GIO_REG_WR_ADDR(rw_pe_dout),
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- &virtual_dummy,
-#endif
-};
-
-static volatile unsigned long *data_in[NUM_PORTS] = {
- GIO_REG_RD_ADDR(r_pa_din),
- GIO_REG_RD_ADDR(r_pb_din),
- &led_dummy,
- GIO_REG_RD_ADDR(r_pc_din),
- GIO_REG_RD_ADDR(r_pd_din),
- GIO_REG_RD_ADDR(r_pe_din),
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- &virtual_dummy,
-#endif
-};
-
-static unsigned long changeable_dir[NUM_PORTS] = {
- CONFIG_ETRAX_PA_CHANGEABLE_DIR,
- CONFIG_ETRAX_PB_CHANGEABLE_DIR,
- 0,
- CONFIG_ETRAX_PC_CHANGEABLE_DIR,
- CONFIG_ETRAX_PD_CHANGEABLE_DIR,
- CONFIG_ETRAX_PE_CHANGEABLE_DIR,
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- CONFIG_ETRAX_PV_CHANGEABLE_DIR,
-#endif
-};
-
-static unsigned long changeable_bits[NUM_PORTS] = {
- CONFIG_ETRAX_PA_CHANGEABLE_BITS,
- CONFIG_ETRAX_PB_CHANGEABLE_BITS,
- 0,
- CONFIG_ETRAX_PC_CHANGEABLE_BITS,
- CONFIG_ETRAX_PD_CHANGEABLE_BITS,
- CONFIG_ETRAX_PE_CHANGEABLE_BITS,
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- CONFIG_ETRAX_PV_CHANGEABLE_BITS,
-#endif
-};
-
-static volatile unsigned long *dir_oe[NUM_PORTS] = {
- GIO_REG_WR_ADDR(rw_pa_oe),
- GIO_REG_WR_ADDR(rw_pb_oe),
- &led_dummy,
- GIO_REG_WR_ADDR(rw_pc_oe),
- GIO_REG_WR_ADDR(rw_pd_oe),
- GIO_REG_WR_ADDR(rw_pe_oe),
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- &virtual_rw_pv_oe,
-#endif
-};
-
-
-
-static unsigned int gpio_poll(struct file *file, struct poll_table_struct *wait)
-{
- unsigned int mask = 0;
- struct gpio_private *priv = file->private_data;
- unsigned long data;
- poll_wait(file, &priv->alarm_wq, wait);
- if (priv->minor == GPIO_MINOR_A) {
- reg_gio_rw_intr_cfg intr_cfg;
- unsigned long tmp;
- unsigned long flags;
-
- local_irq_save(flags);
- data = REG_TYPE_CONV(unsigned long, reg_gio_r_pa_din,
- REG_RD(gio, regi_gio, r_pa_din));
- /* PA has support for interrupt
- * lets activate high for those low and with highalarm set
- */
- intr_cfg = REG_RD(gio, regi_gio, rw_intr_cfg);
-
- tmp = ~data & priv->highalarm & 0xFF;
- if (tmp & (1 << 0))
- intr_cfg.pa0 = regk_gio_hi;
- if (tmp & (1 << 1))
- intr_cfg.pa1 = regk_gio_hi;
- if (tmp & (1 << 2))
- intr_cfg.pa2 = regk_gio_hi;
- if (tmp & (1 << 3))
- intr_cfg.pa3 = regk_gio_hi;
- if (tmp & (1 << 4))
- intr_cfg.pa4 = regk_gio_hi;
- if (tmp & (1 << 5))
- intr_cfg.pa5 = regk_gio_hi;
- if (tmp & (1 << 6))
- intr_cfg.pa6 = regk_gio_hi;
- if (tmp & (1 << 7))
- intr_cfg.pa7 = regk_gio_hi;
- /*
- * lets activate low for those high and with lowalarm set
- */
- tmp = data & priv->lowalarm & 0xFF;
- if (tmp & (1 << 0))
- intr_cfg.pa0 = regk_gio_lo;
- if (tmp & (1 << 1))
- intr_cfg.pa1 = regk_gio_lo;
- if (tmp & (1 << 2))
- intr_cfg.pa2 = regk_gio_lo;
- if (tmp & (1 << 3))
- intr_cfg.pa3 = regk_gio_lo;
- if (tmp & (1 << 4))
- intr_cfg.pa4 = regk_gio_lo;
- if (tmp & (1 << 5))
- intr_cfg.pa5 = regk_gio_lo;
- if (tmp & (1 << 6))
- intr_cfg.pa6 = regk_gio_lo;
- if (tmp & (1 << 7))
- intr_cfg.pa7 = regk_gio_lo;
-
- REG_WR(gio, regi_gio, rw_intr_cfg, intr_cfg);
- local_irq_restore(flags);
- } else if (priv->minor <= GPIO_MINOR_E)
- data = *data_in[priv->minor];
- else
- return 0;
-
- if ((data & priv->highalarm) || (~data & priv->lowalarm))
- mask = POLLIN|POLLRDNORM;
-
- DP(printk(KERN_DEBUG "gpio_poll ready: mask 0x%08X\n", mask));
- return mask;
-}
-
-int etrax_gpio_wake_up_check(void)
-{
- struct gpio_private *priv;
- unsigned long data = 0;
- unsigned long flags;
- int ret = 0;
- spin_lock_irqsave(&alarm_lock, flags);
- priv = alarmlist;
- while (priv) {
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- if (priv->minor == GPIO_MINOR_V)
- data = (unsigned long)cached_virtual_gpio_read;
- else {
- data = *data_in[priv->minor];
- if (priv->minor == GPIO_MINOR_A)
- priv->lowalarm |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
- }
-#else
- data = *data_in[priv->minor];
-#endif
- if ((data & priv->highalarm) ||
- (~data & priv->lowalarm)) {
- DP(printk(KERN_DEBUG
- "etrax_gpio_wake_up_check %i\n", priv->minor));
- wake_up_interruptible(&priv->alarm_wq);
- ret = 1;
- }
- priv = priv->next;
- }
- spin_unlock_irqrestore(&alarm_lock, flags);
- return ret;
-}
-
-static irqreturn_t
-gpio_poll_timer_interrupt(int irq, void *dev_id)
-{
- if (gpio_some_alarms)
- return IRQ_RETVAL(etrax_gpio_wake_up_check());
- return IRQ_NONE;
-}
-
-static irqreturn_t
-gpio_pa_interrupt(int irq, void *dev_id)
-{
- reg_gio_rw_intr_mask intr_mask;
- reg_gio_r_masked_intr masked_intr;
- reg_gio_rw_ack_intr ack_intr;
- unsigned long tmp;
- unsigned long tmp2;
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- unsigned char enable_gpiov_ack = 0;
-#endif
-
- /* Find what PA interrupts are active */
- masked_intr = REG_RD(gio, regi_gio, r_masked_intr);
- tmp = REG_TYPE_CONV(unsigned long, reg_gio_r_masked_intr, masked_intr);
-
- /* Find those that we have enabled */
- spin_lock(&alarm_lock);
- tmp &= (gpio_pa_high_alarms | gpio_pa_low_alarms);
- spin_unlock(&alarm_lock);
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- /* Something changed on virtual GPIO. Interrupt is acked by
- * reading the device.
- */
- if (tmp & (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN)) {
- i2c_read(VIRT_I2C_ADDR, (void *)&cached_virtual_gpio_read,
- sizeof(cached_virtual_gpio_read));
- enable_gpiov_ack = 1;
- }
-#endif
-
- /* Ack them */
- ack_intr = REG_TYPE_CONV(reg_gio_rw_ack_intr, unsigned long, tmp);
- REG_WR(gio, regi_gio, rw_ack_intr, ack_intr);
-
- /* Disable those interrupts.. */
- intr_mask = REG_RD(gio, regi_gio, rw_intr_mask);
- tmp2 = REG_TYPE_CONV(unsigned long, reg_gio_rw_intr_mask, intr_mask);
- tmp2 &= ~tmp;
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- /* Do not disable interrupt on virtual GPIO. Changes on virtual
- * pins are only noticed by an interrupt.
- */
- if (enable_gpiov_ack)
- tmp2 |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
-#endif
- intr_mask = REG_TYPE_CONV(reg_gio_rw_intr_mask, unsigned long, tmp2);
- REG_WR(gio, regi_gio, rw_intr_mask, intr_mask);
-
- if (gpio_some_alarms)
- return IRQ_RETVAL(etrax_gpio_wake_up_check());
- return IRQ_NONE;
-}
-
-
-static ssize_t gpio_write(struct file *file, const char *buf, size_t count,
- loff_t *off)
-{
- struct gpio_private *priv = file->private_data;
- unsigned char data, clk_mask, data_mask, write_msb;
- unsigned long flags;
- unsigned long shadow;
- volatile unsigned long *port;
- ssize_t retval = count;
- /* Only bits 0-7 may be used for write operations but allow all
- devices except leds... */
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- if (priv->minor == GPIO_MINOR_V)
- return -EFAULT;
-#endif
- if (priv->minor == GPIO_MINOR_LEDS)
- return -EFAULT;
-
- if (!access_ok(VERIFY_READ, buf, count))
- return -EFAULT;
- clk_mask = priv->clk_mask;
- data_mask = priv->data_mask;
- /* It must have been configured using the IO_CFG_WRITE_MODE */
- /* Perhaps a better error code? */
- if (clk_mask == 0 || data_mask == 0)
- return -EPERM;
- write_msb = priv->write_msb;
- D(printk(KERN_DEBUG "gpio_write: %lu to data 0x%02X clk 0x%02X "
- "msb: %i\n", count, data_mask, clk_mask, write_msb));
- port = data_out[priv->minor];
-
- while (count--) {
- int i;
- data = *buf++;
- if (priv->write_msb) {
- for (i = 7; i >= 0; i--) {
- local_irq_save(flags);
- shadow = *port;
- *port = shadow &= ~clk_mask;
- if (data & 1<<i)
- *port = shadow |= data_mask;
- else
- *port = shadow &= ~data_mask;
- /* For FPGA: min 5.0ns (DCC) before CCLK high */
- *port = shadow |= clk_mask;
- local_irq_restore(flags);
- }
- } else {
- for (i = 0; i <= 7; i++) {
- local_irq_save(flags);
- shadow = *port;
- *port = shadow &= ~clk_mask;
- if (data & 1<<i)
- *port = shadow |= data_mask;
- else
- *port = shadow &= ~data_mask;
- /* For FPGA: min 5.0ns (DCC) before CCLK high */
- *port = shadow |= clk_mask;
- local_irq_restore(flags);
- }
- }
- }
- return retval;
-}
-
-
-
-static int
-gpio_open(struct inode *inode, struct file *filp)
-{
- struct gpio_private *priv;
- int p = iminor(inode);
-
- if (p > GPIO_MINOR_LAST)
- return -EINVAL;
-
- priv = kmalloc(sizeof(struct gpio_private), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
-
- mutex_lock(&gpio_mutex);
- memset(priv, 0, sizeof(*priv));
-
- priv->minor = p;
-
- /* initialize the io/alarm struct */
-
- priv->clk_mask = 0;
- priv->data_mask = 0;
- priv->highalarm = 0;
- priv->lowalarm = 0;
- init_waitqueue_head(&priv->alarm_wq);
-
- filp->private_data = (void *)priv;
-
- /* link it into our alarmlist */
- spin_lock_irq(&alarm_lock);
- priv->next = alarmlist;
- alarmlist = priv;
- spin_unlock_irq(&alarm_lock);
-
- mutex_unlock(&gpio_mutex);
- return 0;
-}
-
-static int
-gpio_release(struct inode *inode, struct file *filp)
-{
- struct gpio_private *p;
- struct gpio_private *todel;
- /* local copies while updating them: */
- unsigned long a_high, a_low;
- unsigned long some_alarms;
-
- /* unlink from alarmlist and free the private structure */
-
- spin_lock_irq(&alarm_lock);
- p = alarmlist;
- todel = filp->private_data;
-
- if (p == todel) {
- alarmlist = todel->next;
- } else {
- while (p->next != todel)
- p = p->next;
- p->next = todel->next;
- }
-
- kfree(todel);
- /* Check if there are still any alarms set */
- p = alarmlist;
- some_alarms = 0;
- a_high = 0;
- a_low = 0;
- while (p) {
- if (p->minor == GPIO_MINOR_A) {
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- p->lowalarm |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
-#endif
- a_high |= p->highalarm;
- a_low |= p->lowalarm;
- }
-
- if (p->highalarm | p->lowalarm)
- some_alarms = 1;
- p = p->next;
- }
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- /* Variables 'some_alarms' and 'a_low' needs to be set here again
- * to ensure that interrupt for virtual GPIO is handled.
- */
- some_alarms = 1;
- a_low |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
-#endif
-
- gpio_some_alarms = some_alarms;
- gpio_pa_high_alarms = a_high;
- gpio_pa_low_alarms = a_low;
- spin_unlock_irq(&alarm_lock);
-
- return 0;
-}
-
-/* Main device API. ioctl's to read/set/clear bits, as well as to
- * set alarms to wait for using a subsequent select().
- */
-
-inline unsigned long setget_input(struct gpio_private *priv, unsigned long arg)
-{
- /* Set direction 0=unchanged 1=input,
- * return mask with 1=input
- */
- unsigned long flags;
- unsigned long dir_shadow;
-
- local_irq_save(flags);
- dir_shadow = *dir_oe[priv->minor];
- dir_shadow &= ~(arg & changeable_dir[priv->minor]);
- *dir_oe[priv->minor] = dir_shadow;
- local_irq_restore(flags);
-
- if (priv->minor == GPIO_MINOR_A)
- dir_shadow ^= 0xFF; /* Only 8 bits */
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- else if (priv->minor == GPIO_MINOR_V)
- dir_shadow ^= 0xFFFF; /* Only 16 bits */
-#endif
- else
- dir_shadow ^= 0x3FFFF; /* Only 18 bits */
- return dir_shadow;
-
-} /* setget_input */
-
-inline unsigned long setget_output(struct gpio_private *priv, unsigned long arg)
-{
- unsigned long flags;
- unsigned long dir_shadow;
-
- local_irq_save(flags);
- dir_shadow = *dir_oe[priv->minor];
- dir_shadow |= (arg & changeable_dir[priv->minor]);
- *dir_oe[priv->minor] = dir_shadow;
- local_irq_restore(flags);
- return dir_shadow;
-} /* setget_output */
-
-static int gpio_leds_ioctl(unsigned int cmd, unsigned long arg);
-
-static int
-gpio_ioctl_unlocked(struct file *file, unsigned int cmd, unsigned long arg)
-{
- unsigned long flags;
- unsigned long val;
- unsigned long shadow;
- struct gpio_private *priv = file->private_data;
- if (_IOC_TYPE(cmd) != ETRAXGPIO_IOCTYPE)
- return -EINVAL;
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- if (priv->minor == GPIO_MINOR_V)
- return virtual_gpio_ioctl(file, cmd, arg);
-#endif
-
- switch (_IOC_NR(cmd)) {
- case IO_READBITS: /* Use IO_READ_INBITS and IO_READ_OUTBITS instead */
- /* Read the port. */
- return *data_in[priv->minor];
- break;
- case IO_SETBITS:
- local_irq_save(flags);
- /* Set changeable bits with a 1 in arg. */
- shadow = *data_out[priv->minor];
- shadow |= (arg & changeable_bits[priv->minor]);
- *data_out[priv->minor] = shadow;
- local_irq_restore(flags);
- break;
- case IO_CLRBITS:
- local_irq_save(flags);
- /* Clear changeable bits with a 1 in arg. */
- shadow = *data_out[priv->minor];
- shadow &= ~(arg & changeable_bits[priv->minor]);
- *data_out[priv->minor] = shadow;
- local_irq_restore(flags);
- break;
- case IO_HIGHALARM:
- /* Set alarm when bits with 1 in arg go high. */
- priv->highalarm |= arg;
- spin_lock_irqsave(&alarm_lock, flags);
- gpio_some_alarms = 1;
- if (priv->minor == GPIO_MINOR_A)
- gpio_pa_high_alarms |= arg;
- spin_unlock_irqrestore(&alarm_lock, flags);
- break;
- case IO_LOWALARM:
- /* Set alarm when bits with 1 in arg go low. */
- priv->lowalarm |= arg;
- spin_lock_irqsave(&alarm_lock, flags);
- gpio_some_alarms = 1;
- if (priv->minor == GPIO_MINOR_A)
- gpio_pa_low_alarms |= arg;
- spin_unlock_irqrestore(&alarm_lock, flags);
- break;
- case IO_CLRALARM:
- /* Clear alarm for bits with 1 in arg. */
- priv->highalarm &= ~arg;
- priv->lowalarm &= ~arg;
- spin_lock_irqsave(&alarm_lock, flags);
- if (priv->minor == GPIO_MINOR_A) {
- if (gpio_pa_high_alarms & arg ||
- gpio_pa_low_alarms & arg)
- /* Must update the gpio_pa_*alarms masks */
- ;
- }
- spin_unlock_irqrestore(&alarm_lock, flags);
- break;
- case IO_READDIR: /* Use IO_SETGET_INPUT/OUTPUT instead! */
- /* Read direction 0=input 1=output */
- return *dir_oe[priv->minor];
- case IO_SETINPUT: /* Use IO_SETGET_INPUT instead! */
- /* Set direction 0=unchanged 1=input,
- * return mask with 1=input
- */
- return setget_input(priv, arg);
- break;
- case IO_SETOUTPUT: /* Use IO_SETGET_OUTPUT instead! */
- /* Set direction 0=unchanged 1=output,
- * return mask with 1=output
- */
- return setget_output(priv, arg);
-
- case IO_CFG_WRITE_MODE:
- {
- unsigned long dir_shadow;
- dir_shadow = *dir_oe[priv->minor];
-
- priv->clk_mask = arg & 0xFF;
- priv->data_mask = (arg >> 8) & 0xFF;
- priv->write_msb = (arg >> 16) & 0x01;
- /* Check if we're allowed to change the bits and
- * the direction is correct
- */
- if (!((priv->clk_mask & changeable_bits[priv->minor]) &&
- (priv->data_mask & changeable_bits[priv->minor]) &&
- (priv->clk_mask & dir_shadow) &&
- (priv->data_mask & dir_shadow))) {
- priv->clk_mask = 0;
- priv->data_mask = 0;
- return -EPERM;
- }
- break;
- }
- case IO_READ_INBITS:
- /* *arg is result of reading the input pins */
- val = *data_in[priv->minor];
- if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
- return -EFAULT;
- return 0;
- break;
- case IO_READ_OUTBITS:
- /* *arg is result of reading the output shadow */
- val = *data_out[priv->minor];
- if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
- return -EFAULT;
- break;
- case IO_SETGET_INPUT:
- /* bits set in *arg is set to input,
- * *arg updated with current input pins.
- */
- if (copy_from_user(&val, (unsigned long *)arg, sizeof(val)))
- return -EFAULT;
- val = setget_input(priv, val);
- if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
- return -EFAULT;
- break;
- case IO_SETGET_OUTPUT:
- /* bits set in *arg is set to output,
- * *arg updated with current output pins.
- */
- if (copy_from_user(&val, (unsigned long *)arg, sizeof(val)))
- return -EFAULT;
- val = setget_output(priv, val);
- if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
- return -EFAULT;
- break;
- default:
- if (priv->minor == GPIO_MINOR_LEDS)
- return gpio_leds_ioctl(cmd, arg);
- else
- return -EINVAL;
- } /* switch */
-
- return 0;
-}
-
-static long gpio_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-{
- long ret;
-
- mutex_lock(&gpio_mutex);
- ret = gpio_ioctl_unlocked(file, cmd, arg);
- mutex_unlock(&gpio_mutex);
-
- return ret;
-}
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static int
-virtual_gpio_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-{
- unsigned long flags;
- unsigned short val;
- unsigned short shadow;
- struct gpio_private *priv = file->private_data;
-
- switch (_IOC_NR(cmd)) {
- case IO_SETBITS:
- local_irq_save(flags);
- /* Set changeable bits with a 1 in arg. */
- i2c_read(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
- shadow |= ~*dir_oe[priv->minor];
- shadow |= (arg & changeable_bits[priv->minor]);
- i2c_write(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
- local_irq_restore(flags);
- break;
- case IO_CLRBITS:
- local_irq_save(flags);
- /* Clear changeable bits with a 1 in arg. */
- i2c_read(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
- shadow |= ~*dir_oe[priv->minor];
- shadow &= ~(arg & changeable_bits[priv->minor]);
- i2c_write(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
- local_irq_restore(flags);
- break;
- case IO_HIGHALARM:
- /* Set alarm when bits with 1 in arg go high. */
- priv->highalarm |= arg;
- spin_lock(&alarm_lock);
- gpio_some_alarms = 1;
- spin_unlock(&alarm_lock);
- break;
- case IO_LOWALARM:
- /* Set alarm when bits with 1 in arg go low. */
- priv->lowalarm |= arg;
- spin_lock(&alarm_lock);
- gpio_some_alarms = 1;
- spin_unlock(&alarm_lock);
- break;
- case IO_CLRALARM:
- /* Clear alarm for bits with 1 in arg. */
- priv->highalarm &= ~arg;
- priv->lowalarm &= ~arg;
- spin_lock(&alarm_lock);
- spin_unlock(&alarm_lock);
- break;
- case IO_CFG_WRITE_MODE:
- {
- unsigned long dir_shadow;
- dir_shadow = *dir_oe[priv->minor];
-
- priv->clk_mask = arg & 0xFF;
- priv->data_mask = (arg >> 8) & 0xFF;
- priv->write_msb = (arg >> 16) & 0x01;
- /* Check if we're allowed to change the bits and
- * the direction is correct
- */
- if (!((priv->clk_mask & changeable_bits[priv->minor]) &&
- (priv->data_mask & changeable_bits[priv->minor]) &&
- (priv->clk_mask & dir_shadow) &&
- (priv->data_mask & dir_shadow))) {
- priv->clk_mask = 0;
- priv->data_mask = 0;
- return -EPERM;
- }
- break;
- }
- case IO_READ_INBITS:
- /* *arg is result of reading the input pins */
- val = cached_virtual_gpio_read;
- val &= ~*dir_oe[priv->minor];
- if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
- return -EFAULT;
- return 0;
- break;
- case IO_READ_OUTBITS:
- /* *arg is result of reading the output shadow */
- i2c_read(VIRT_I2C_ADDR, (void *)&val, sizeof(val));
- val &= *dir_oe[priv->minor];
- if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
- return -EFAULT;
- break;
- case IO_SETGET_INPUT:
- {
- /* bits set in *arg is set to input,
- * *arg updated with current input pins.
- */
- unsigned short input_mask = ~*dir_oe[priv->minor];
- if (copy_from_user(&val, (unsigned long *)arg, sizeof(val)))
- return -EFAULT;
- val = setget_input(priv, val);
- if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
- return -EFAULT;
- if ((input_mask & val) != input_mask) {
- /* Input pins changed. All ports desired as input
- * should be set to logic 1.
- */
- unsigned short change = input_mask ^ val;
- i2c_read(VIRT_I2C_ADDR, (void *)&shadow,
- sizeof(shadow));
- shadow &= ~change;
- shadow |= val;
- i2c_write(VIRT_I2C_ADDR, (void *)&shadow,
- sizeof(shadow));
- }
- break;
- }
- case IO_SETGET_OUTPUT:
- /* bits set in *arg is set to output,
- * *arg updated with current output pins.
- */
- if (copy_from_user(&val, (unsigned long *)arg, sizeof(val)))
- return -EFAULT;
- val = setget_output(priv, val);
- if (copy_to_user((unsigned long *)arg, &val, sizeof(val)))
- return -EFAULT;
- break;
- default:
- return -EINVAL;
- } /* switch */
- return 0;
-}
-#endif /* CONFIG_ETRAX_VIRTUAL_GPIO */
-
-static int
-gpio_leds_ioctl(unsigned int cmd, unsigned long arg)
-{
- unsigned char green;
- unsigned char red;
-
- switch (_IOC_NR(cmd)) {
- case IO_LEDACTIVE_SET:
- green = ((unsigned char) arg) & 1;
- red = (((unsigned char) arg) >> 1) & 1;
- CRIS_LED_ACTIVE_SET_G(green);
- CRIS_LED_ACTIVE_SET_R(red);
- break;
-
- default:
- return -EINVAL;
- } /* switch */
-
- return 0;
-}
-
-static const struct file_operations gpio_fops = {
- .owner = THIS_MODULE,
- .poll = gpio_poll,
- .unlocked_ioctl = gpio_ioctl,
- .write = gpio_write,
- .open = gpio_open,
- .release = gpio_release,
- .llseek = noop_llseek,
-};
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-static void
-virtual_gpio_init(void)
-{
- reg_gio_rw_intr_cfg intr_cfg;
- reg_gio_rw_intr_mask intr_mask;
- unsigned short shadow;
-
- shadow = ~virtual_rw_pv_oe; /* Input ports should be set to logic 1 */
- shadow |= CONFIG_ETRAX_DEF_GIO_PV_OUT;
- i2c_write(VIRT_I2C_ADDR, (void *)&shadow, sizeof(shadow));
-
- /* Set interrupt mask and on what state the interrupt shall trigger.
- * For virtual gpio the interrupt shall trigger on logic '0'.
- */
- intr_cfg = REG_RD(gio, regi_gio, rw_intr_cfg);
- intr_mask = REG_RD(gio, regi_gio, rw_intr_mask);
-
- switch (CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN) {
- case 0:
- intr_cfg.pa0 = regk_gio_lo;
- intr_mask.pa0 = regk_gio_yes;
- break;
- case 1:
- intr_cfg.pa1 = regk_gio_lo;
- intr_mask.pa1 = regk_gio_yes;
- break;
- case 2:
- intr_cfg.pa2 = regk_gio_lo;
- intr_mask.pa2 = regk_gio_yes;
- break;
- case 3:
- intr_cfg.pa3 = regk_gio_lo;
- intr_mask.pa3 = regk_gio_yes;
- break;
- case 4:
- intr_cfg.pa4 = regk_gio_lo;
- intr_mask.pa4 = regk_gio_yes;
- break;
- case 5:
- intr_cfg.pa5 = regk_gio_lo;
- intr_mask.pa5 = regk_gio_yes;
- break;
- case 6:
- intr_cfg.pa6 = regk_gio_lo;
- intr_mask.pa6 = regk_gio_yes;
- break;
- case 7:
- intr_cfg.pa7 = regk_gio_lo;
- intr_mask.pa7 = regk_gio_yes;
- break;
- }
-
- REG_WR(gio, regi_gio, rw_intr_cfg, intr_cfg);
- REG_WR(gio, regi_gio, rw_intr_mask, intr_mask);
-
- gpio_pa_low_alarms |= (1 << CONFIG_ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN);
- gpio_some_alarms = 1;
-}
-#endif
-
-/* main driver initialization routine, called from mem.c */
-
-static __init int
-gpio_init(void)
-{
- int res;
-
- /* do the formalities */
-
- res = register_chrdev(GPIO_MAJOR, gpio_name, &gpio_fops);
- if (res < 0) {
- printk(KERN_ERR "gpio: couldn't get a major number.\n");
- return res;
- }
-
- /* Clear all leds */
- CRIS_LED_NETWORK_GRP0_SET(0);
- CRIS_LED_NETWORK_GRP1_SET(0);
- CRIS_LED_ACTIVE_SET(0);
- CRIS_LED_DISK_READ(0);
- CRIS_LED_DISK_WRITE(0);
-
- printk(KERN_INFO "ETRAX FS GPIO driver v2.5, (c) 2003-2007 "
- "Axis Communications AB\n");
- /* We call etrax_gpio_wake_up_check() from timer interrupt */
- if (request_irq(TIMER0_INTR_VECT, gpio_poll_timer_interrupt,
- IRQF_SHARED, "gpio poll", &alarmlist))
- printk(KERN_ERR "timer0 irq for gpio\n");
-
- if (request_irq(GIO_INTR_VECT, gpio_pa_interrupt,
- IRQF_SHARED, "gpio PA", &alarmlist))
- printk(KERN_ERR "PA irq for gpio\n");
-
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- virtual_gpio_init();
-#endif
-
- return res;
-}
-
-/* this makes sure that gpio_init is called during kernel boot */
-
-module_init(gpio_init);
diff --git a/kernel/arch/cris/arch-v32/drivers/sync_serial.c b/kernel/arch/cris/arch-v32/drivers/sync_serial.c
index 4dda9bd6b..e989cee77 100644
--- a/kernel/arch/cris/arch-v32/drivers/sync_serial.c
+++ b/kernel/arch/cris/arch-v32/drivers/sync_serial.c
@@ -1464,7 +1464,7 @@ static inline void handle_rx_packet(struct sync_port *port)
if (port->write_ts_idx == NBR_IN_DESCR)
port->write_ts_idx = 0;
idx = port->write_ts_idx++;
- do_posix_clock_monotonic_gettime(&port->timestamp[idx]);
+ ktime_get_ts(&port->timestamp[idx]);
port->in_buffer_len += port->inbufchunk;
}
spin_unlock_irqrestore(&port->lock, flags);