1 files changed, 0 insertions, 120 deletions
diff --git a/kernel/Documentation/devicetree/bindings/video/exynos_dp.txt b/kernel/Documentation/devicetree/bindings/video/exynos_dp.txt
deleted file mode 100644
index 7a3a9cdb8..000000000
--- a/kernel/Documentation/devicetree/bindings/video/exynos_dp.txt
+++ /dev/null
@@ -1,120 +0,0 @@
-The Exynos display port interface should be configured based on
-the type of panel connected to it.
-
-We use two nodes:
-	-dp-controller node
-	-dptx-phy node(defined inside dp-controller node)
-
-For the DP-PHY initialization, we use the dptx-phy node.
-Required properties for dptx-phy: deprecated, use phys and phy-names
-	-reg: deprecated
-		Base address of DP PHY register.
-	-samsung,enable-mask: deprecated
-		The bit-mask used to enable/disable DP PHY.
-
-For the Panel initialization, we read data from dp-controller node.
-Required properties for dp-controller:
-	-compatible:
-		should be "samsung,exynos5-dp".
-	-reg:
-		physical base address of the controller and length
-		of memory mapped region.
-	-interrupts:
-		interrupt combiner values.
-	-clocks:
-		from common clock binding: handle to dp clock.
-	-clock-names:
-		from common clock binding: Shall be "dp".
-	-interrupt-parent:
-		phandle to Interrupt combiner node.
-	-phys:
-		from general PHY binding: the phandle for the PHY device.
-	-phy-names:
-		from general PHY binding: Should be "dp".
-	-samsung,color-space:
-		input video data format.
-			COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2
-	-samsung,dynamic-range:
-		dynamic range for input video data.
-			VESA = 0, CEA = 1
-	-samsung,ycbcr-coeff:
-		YCbCr co-efficients for input video.
-			COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1
-	-samsung,color-depth:
-		number of bits per colour component.
-			COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3
-	-samsung,link-rate:
-		link rate supported by the panel.
-			LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A
-	-samsung,lane-count:
-		number of lanes supported by the panel.
-			LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4
-	- display-timings: timings for the connected panel as described by
-		Documentation/devicetree/bindings/video/display-timing.txt
-
-Optional properties for dp-controller:
-	-interlaced:
-		interlace scan mode.
-			Progressive if defined, Interlaced if not defined
-	-vsync-active-high:
-		VSYNC polarity configuration.
-			High if defined, Low if not defined
-	-hsync-active-high:
-		HSYNC polarity configuration.
-			High if defined, Low if not defined
-	-samsung,hpd-gpio:
-		Hotplug detect GPIO.
-			Indicates which GPIO should be used for hotplug
-			detection
-	-video interfaces: Device node can contain video interface port
-			    nodes according to [1].
-
-[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Example:
-
-SOC specific portion:
-	dp-controller {
-		compatible = "samsung,exynos5-dp";
-		reg = <0x145b0000 0x10000>;
-		interrupts = <10 3>;
-		interrupt-parent = <&combiner>;
-		clocks = <&clock 342>;
-		clock-names = "dp";
-
-		phys = <&dp_phy>;
-		phy-names = "dp";
-	};
-
-Board Specific portion:
-	dp-controller {
-		samsung,color-space = <0>;
-		samsung,dynamic-range = <0>;
-		samsung,ycbcr-coeff = <0>;
-		samsung,color-depth = <1>;
-		samsung,link-rate = <0x0a>;
-		samsung,lane-count = <4>;
-
-		display-timings {
-			native-mode = <&lcd_timing>;
-			lcd_timing: 1366x768 {
-				clock-frequency = <70589280>;
-				hactive = <1366>;
-				vactive = <768>;
-				hfront-porch = <40>;
-				hback-porch = <40>;
-				hsync-len = <32>;
-				vback-porch = <10>;
-				vfront-porch = <12>;
-				vsync-len = <6>;
-			};
-		};
-
-		ports {
-			port@0 {
-				dp_out: endpoint {
-					remote-endpoint = <&bridge_in>;
-				};
-			};
-		};
-	};