diff options
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/media/i2c')
11 files changed, 488 insertions, 0 deletions
diff --git a/kernel/Documentation/devicetree/bindings/media/i2c/adv7343.txt b/kernel/Documentation/devicetree/bindings/media/i2c/adv7343.txt new file mode 100644 index 000000000..5653bc242 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/media/i2c/adv7343.txt @@ -0,0 +1,48 @@ +* Analog Devices adv7343 video encoder + +The ADV7343 are high speed, digital-to-analog video encoders in a 64-lead LQFP +package. Six high speed, 3.3 V, 11-bit video DACs provide support for composite +(CVBS), S-Video (Y-C), and component (YPrPb/RGB) analog outputs in standard +definition (SD), enhanced definition (ED), or high definition (HD) video +formats. + +Required Properties : +- compatible: Must be "adi,adv7343" + +Optional Properties : +- adi,power-mode-sleep-mode: on enable the current consumption is reduced to + micro ampere level. All DACs and the internal PLL + circuit are disabled. +- adi,power-mode-pll-ctrl: PLL and oversampling control. This control allows + internal PLL 1 circuit to be powered down and the + oversampling to be switched off. +- ad,adv7343-power-mode-dac: array configuring the power on/off DAC's 1..6, + 0 = OFF and 1 = ON, Default value when this + property is not specified is <0 0 0 0 0 0>. +- ad,adv7343-sd-config-dac-out: array configure SD DAC Output's 1 and 2, 0 = OFF + and 1 = ON, Default value when this property is + not specified is <0 0>. + +Example: + +i2c0@1c22000 { + ... + ... + + adv7343@2a { + compatible = "adi,adv7343"; + reg = <0x2a>; + + port { + adv7343_1: endpoint { + adi,power-mode-sleep-mode; + adi,power-mode-pll-ctrl; + /* Use DAC1..3, DAC6 */ + adi,dac-enable = <1 1 1 0 0 1>; + /* Use SD DAC output 1 */ + adi,sd-dac-enable = <1 0>; + }; + }; + }; + ... +}; diff --git a/kernel/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/kernel/Documentation/devicetree/bindings/media/i2c/adv7604.txt new file mode 100644 index 000000000..c27cede3b --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/media/i2c/adv7604.txt @@ -0,0 +1,70 @@ +* Analog Devices ADV7604/11 video decoder with HDMI receiver + +The ADV7604 and ADV7611 are multiformat video decoders with an integrated HDMI +receiver. The ADV7604 has four multiplexed HDMI inputs and one analog input, +and the ADV7611 has one HDMI input and no analog input. + +These device tree bindings support the ADV7611 only at the moment. + +Required Properties: + + - compatible: Must contain one of the following + - "adi,adv7611" for the ADV7611 + + - reg: I2C slave address + + - hpd-gpios: References to the GPIOs that control the HDMI hot-plug + detection pins, one per HDMI input. The active flag indicates the GPIO + level that enables hot-plug detection. + +The device node must contain one 'port' child node per device input and output +port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes +are numbered as follows. + + Port ADV7611 +------------------------------------------------------------ + HDMI 0 + Digital output 1 + +The digital output port node must contain at least one endpoint. + +Optional Properties: + + - reset-gpios: Reference to the GPIO connected to the device's reset pin. + +Optional Endpoint Properties: + + The following three properties are defined in video-interfaces.txt and are + valid for source endpoints only. + + - hsync-active: Horizontal synchronization polarity. Defaults to active low. + - vsync-active: Vertical synchronization polarity. Defaults to active low. + - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge. + + If none of hsync-active, vsync-active and pclk-sample is specified the + endpoint will use embedded BT.656 synchronization. + + +Example: + + hdmi_receiver@4c { + compatible = "adi,adv7611"; + reg = <0x4c>; + + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; + + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + }; + port@1 { + reg = <1>; + hdmi_in: endpoint { + remote-endpoint = <&ccdc_in>; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/media/i2c/mt9m111.txt b/kernel/Documentation/devicetree/bindings/media/i2c/mt9m111.txt new file mode 100644 index 000000000..ed5a334b1 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/media/i2c/mt9m111.txt @@ -0,0 +1,28 @@ +Micron 1.3Mp CMOS Digital Image Sensor + +The Micron MT9M111 is a CMOS active pixel digital image sensor with an active +array size of 1280H x 1024V. It is programmable through a simple two-wire serial +interface. + +Required Properties: +- compatible: value should be "micron,mt9m111" + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c_master { + mt9m111@5d { + compatible = "micron,mt9m111"; + reg = <0x5d>; + + remote = <&pxa_camera>; + port { + mt9m111_1: endpoint { + bus-width = <8>; + remote-endpoint = <&pxa_camera>; + }; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/media/i2c/mt9p031.txt b/kernel/Documentation/devicetree/bindings/media/i2c/mt9p031.txt new file mode 100644 index 000000000..cb60443ff --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/media/i2c/mt9p031.txt @@ -0,0 +1,40 @@ +* Aptina 1/2.5-Inch 5Mp CMOS Digital Image Sensor + +The Aptina MT9P031 is a 1/2.5-inch CMOS active pixel digital image sensor with +an active array size of 2592H x 1944V. It is programmable through a simple +two-wire serial interface. + +Required Properties: +- compatible: value should be either one among the following + (a) "aptina,mt9p031" for mt9p031 sensor + (b) "aptina,mt9p031m" for mt9p031m sensor + +- input-clock-frequency: Input clock frequency. + +- pixel-clock-frequency: Pixel clock frequency. + +Optional Properties: +- reset-gpios: Chip reset GPIO + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + mt9p031@5d { + compatible = "aptina,mt9p031"; + reg = <0x5d>; + reset-gpios = <&gpio3 30 0>; + + port { + mt9p031_1: endpoint { + input-clock-frequency = <6000000>; + pixel-clock-frequency = <96000000>; + }; + }; + }; + ... + }; diff --git a/kernel/Documentation/devicetree/bindings/media/i2c/mt9v032.txt b/kernel/Documentation/devicetree/bindings/media/i2c/mt9v032.txt new file mode 100644 index 000000000..202565313 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/media/i2c/mt9v032.txt @@ -0,0 +1,39 @@ +* Aptina 1/3-Inch WVGA CMOS Digital Image Sensor + +The Aptina MT9V032 is a 1/3-inch CMOS active pixel digital image sensor with +an active array size of 752H x 480V. It is programmable through a simple +two-wire serial interface. + +Required Properties: + +- compatible: value should be either one among the following + (a) "aptina,mt9v022" for MT9V022 color sensor + (b) "aptina,mt9v022m" for MT9V022 monochrome sensor + (c) "aptina,mt9v024" for MT9V024 color sensor + (d) "aptina,mt9v024m" for MT9V024 monochrome sensor + (e) "aptina,mt9v032" for MT9V032 color sensor + (f) "aptina,mt9v032m" for MT9V032 monochrome sensor + (g) "aptina,mt9v034" for MT9V034 color sensor + (h) "aptina,mt9v034m" for MT9V034 monochrome sensor + +Optional Properties: + +- link-frequencies: List of allowed link frequencies in Hz. Each frequency is + expressed as a 64-bit big-endian integer. + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + mt9v032@5c { + compatible = "aptina,mt9v032"; + reg = <0x5c>; + + port { + mt9v032_out: endpoint { + link-frequencies = /bits/ 64 + <13000000 26600000 27000000>; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/kernel/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt new file mode 100644 index 000000000..855e1faf7 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt @@ -0,0 +1,63 @@ +SMIA/SMIA++ sensor + +SMIA (Standard Mobile Imaging Architecture) is an image sensor standard +defined jointly by Nokia and ST. SMIA++, defined by Nokia, is an extension +of that. These definitions are valid for both types of sensors. + +More detailed documentation can be found in +Documentation/devicetree/bindings/media/video-interfaces.txt . + + +Mandatory properties +-------------------- + +- compatible: "nokia,smia" +- reg: I2C address (0x10, or an alternative address) +- vana-supply: Analogue voltage supply (VANA), typically 2,8 volts (sensor + dependent). +- clocks: External clock to the sensor +- clock-frequency: Frequency of the external clock to the sensor +- link-frequencies: List of allowed data link frequencies. An array of + 64-bit elements. + + +Optional properties +------------------- + +- nokia,nvm-size: The size of the NVM, in bytes. If the size is not given, + the NVM contents will not be read. +- reset-gpios: XSHUTDOWN GPIO + + +Endpoint node mandatory properties +---------------------------------- + +- clock-lanes: <0> +- data-lanes: <1..n> +- remote-endpoint: A phandle to the bus receiver's endpoint node. + + +Example +------- + +&i2c2 { + clock-frequency = <400000>; + + smiapp_1: camera@10 { + compatible = "nokia,smia"; + reg = <0x10>; + reset-gpios = <&gpio3 20 0>; + vana-supply = <&vaux3>; + clocks = <&omap3_isp 0>; + clock-frequency = <9600000>; + nokia,nvm-size = <512>; /* 8 * 64 */ + link-frequencies = /bits/ 64 <199200000 210000000 499200000>; + port { + smiapp_1_1: endpoint { + clock-lanes = <0>; + data-lanes = <1 2>; + remote-endpoint = <&csi2a_ep>; + }; + }; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/media/i2c/ov2640.txt b/kernel/Documentation/devicetree/bindings/media/i2c/ov2640.txt new file mode 100644 index 000000000..c429b5bdc --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/media/i2c/ov2640.txt @@ -0,0 +1,46 @@ +* Omnivision OV2640 CMOS sensor + +The Omnivision OV2640 sensor support multiple resolutions output, such as +CIF, SVGA, UXGA. It also can support YUV422/420, RGB565/555 or raw RGB +output format. + +Required Properties: +- compatible: should be "ovti,ov2640" +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". + +Optional Properties: +- resetb-gpios: reference to the GPIO connected to the resetb pin, if any. +- pwdn-gpios: reference to the GPIO connected to the pwdn pin, if any. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c1: i2c@f0018000 { + ov2640: camera@0x30 { + compatible = "ovti,ov2640"; + reg = <0x30>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck1 &pinctrl_ov2640_pwdn &pinctrl_ov2640_resetb>; + + resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>; + pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>; + + clocks = <&pck1>; + clock-names = "xvclk"; + + assigned-clocks = <&pck1>; + assigned-clock-rates = <25000000>; + + port { + ov2640_0: endpoint { + remote-endpoint = <&isi_0>; + bus-width = <8>; + }; + }; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/media/i2c/ov2659.txt b/kernel/Documentation/devicetree/bindings/media/i2c/ov2659.txt new file mode 100644 index 000000000..cabc7d827 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/media/i2c/ov2659.txt @@ -0,0 +1,38 @@ +* OV2659 1/5-Inch 2Mp SOC Camera + +The Omnivision OV2659 is a 1/5-inch SOC camera, with an active array size of +1632H x 1212V. It is programmable through a SCCB. The OV2659 sensor supports +multiple resolutions output, such as UXGA, SVGA, 720p. It also can support +YUV422, RGB565/555 or raw RGB output formats. + +Required Properties: +- compatible: Must be "ovti,ov2659" +- reg: I2C slave address +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". +- link-frequencies: target pixel clock frequency. + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + ov2659@30 { + compatible = "ovti,ov2659"; + reg = <0x30>; + + clocks = <&clk_ov2659 0>; + clock-names = "xvclk"; + + port { + ov2659_0: endpoint { + remote-endpoint = <&vpfe_ep>; + link-frequencies = /bits/ 64 <70000000>; + }; + }; + }; + ... + }; diff --git a/kernel/Documentation/devicetree/bindings/media/i2c/ths8200.txt b/kernel/Documentation/devicetree/bindings/media/i2c/ths8200.txt new file mode 100644 index 000000000..285f6ae7d --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/media/i2c/ths8200.txt @@ -0,0 +1,19 @@ +* Texas Instruments THS8200 video encoder + +The ths8200 device is a digital to analog converter used in DVD players, video +recorders, set-top boxes. + +Required Properties : +- compatible : value must be "ti,ths8200" + +Example: + + i2c0@1c22000 { + ... + ... + ths8200@5c { + compatible = "ti,ths8200"; + reg = <0x5c>; + }; + ... + }; diff --git a/kernel/Documentation/devicetree/bindings/media/i2c/tvp514x.txt b/kernel/Documentation/devicetree/bindings/media/i2c/tvp514x.txt new file mode 100644 index 000000000..46752cc71 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/media/i2c/tvp514x.txt @@ -0,0 +1,44 @@ +* Texas Instruments TVP514x video decoder + +The TVP5146/TVP5146m2/TVP5147/TVP5147m1 device is high quality, single-chip +digital video decoder that digitizes and decodes all popular baseband analog +video formats into digital video component. The tvp514x decoder supports analog- +to-digital (A/D) conversion of component RGB and YPbPr signals as well as A/D +conversion and decoding of NTSC, PAL and SECAM composite and S-video into +component YCbCr. + +Required Properties : +- compatible : value should be either one among the following + (a) "ti,tvp5146" for tvp5146 decoder. + (b) "ti,tvp5146m2" for tvp5146m2 decoder. + (c) "ti,tvp5147" for tvp5147 decoder. + (d) "ti,tvp5147m1" for tvp5147m1 decoder. + +- hsync-active: HSYNC Polarity configuration for endpoint. + +- vsync-active: VSYNC Polarity configuration for endpoint. + +- pclk-sample: Clock polarity of the endpoint. + +For further reading on port node refer to Documentation/devicetree/bindings/ +media/video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + tvp514x@5c { + compatible = "ti,tvp5146"; + reg = <0x5c>; + + port { + tvp514x_1: endpoint { + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + }; + }; + }; + ... + }; diff --git a/kernel/Documentation/devicetree/bindings/media/i2c/tvp7002.txt b/kernel/Documentation/devicetree/bindings/media/i2c/tvp7002.txt new file mode 100644 index 000000000..5f28b5d9a --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/media/i2c/tvp7002.txt @@ -0,0 +1,53 @@ +* Texas Instruments TV7002 video decoder + +The TVP7002 device supports digitizing of video and graphics signal in RGB and +YPbPr color space. + +Required Properties : +- compatible : Must be "ti,tvp7002" + +Optional Properties: +- hsync-active: HSYNC Polarity configuration for the bus. Default value when + this property is not specified is <0>. + +- vsync-active: VSYNC Polarity configuration for the bus. Default value when + this property is not specified is <0>. + +- pclk-sample: Clock polarity of the bus. Default value when this property is + not specified is <0>. + +- sync-on-green-active: Active state of Sync-on-green signal property of the + endpoint. + 0 = Normal Operation (Active Low, Default) + 1 = Inverted operation + +- field-even-active: Active-high Field ID output polarity control of the bus. + Under normal operation, the field ID output is set to logic 1 for an odd field + (field 1) and set to logic 0 for an even field (field 0). + 0 = Normal Operation (Active Low, Default) + 1 = FID output polarity inverted + +For further reading of port node refer Documentation/devicetree/bindings/media/ +video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + tvp7002@5c { + compatible = "ti,tvp7002"; + reg = <0x5c>; + + port { + tvp7002_1: endpoint { + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + sync-on-green-active = <1>; + field-even-active = <0>; + }; + }; + }; + ... + }; |