Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

1 files changed, 151 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/include/configs/tny_a9260.h b/qemu/roms/u-boot/include/configs/tny_a9260.h
new file mode 100644
index 000000000..32f6b00bb
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/tny_a9260.h
@@ -0,0 +1,151 @@
+/*
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian@popies.net>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * Copyright (C) 2009
+ * Albin Tonnerre, Free Electrons <albin.tonnerre@free-electrons.com>
+ *
+ * Configuation settings for the Calao TNY-A9260 and TNY-A9G20 boards
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * SoC must be defined first, before hardware.h is included.
+ * In this case SoC is defined in boards.cfg.
+ */
+#include <asm/hardware.h>
+
+#if defined(CONFIG_TNY_A9260_NANDFLASH) || defined(CONFIG_TNY_A9G20_NANDFLASH)
+#define CONFIG_ENV_IS_IN_NAND
+#else
+#define CONFIG_ENV_IS_IN_EEPROM
+#endif
+
+/* Define actual evaluation board type from used processor type */
+#ifdef CONFIG_AT91SAM9G20
+# define CONFIG_TNY_A9G20
+# define MACH_TYPE_TNY_A9G20		2059
+# define CONFIG_MACH_TYPE		MACH_TYPE_TNY_A9G20
+#else
+# define CONFIG_TNY_A9260
+# define MACH_TYPE_TNY_A9260		2058
+# define CONFIG_MACH_TYPE		MACH_TYPE_TNY_A9260
+#endif
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_SLOW_CLOCK	32768		/* slow clock xtal */
+#define CONFIG_SYS_AT91_MAIN_CLOCK	12000000	/* 12 MHz crystal */
+
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_CMDLINE_TAG	        /* enable passing of ATAGs	*/
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_SKIP_LOWLEVEL_INIT
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_ATMEL_LEGACY
+#define CONFIG_AT91_GPIO
+
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE		ATMEL_BASE_DBGU
+#define	CONFIG_USART_ID			ATMEL_ID_SYS
+#define CONFIG_BAUDRATE			115200
+
+#define CONFIG_BOOTDELAY	3
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+#undef CONFIG_CMD_SOURCE
+#undef CONFIG_CMD_USB
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_SYS_SDRAM_BASE		ATMEL_BASE_CS1
+#define CONFIG_SYS_SDRAM_SIZE		0x04000000	/* 64 megs */
+# define CONFIG_SYS_INIT_SP_ADDR \
+	(ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
+/* SPI EEPROM */
+#define CONFIG_SPI
+#define CONFIG_CMD_SPI
+#define CONFIG_ATMEL_SPI
+#define CONFIG_SYS_SPI_WRITE_TOUT		(5 * CONFIG_SYS_HZ)
+
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SPI_M95XXX
+#define CONFIG_SYS_EEPROM_SIZE 0x10000
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
+
+/* NAND flash */
+#define CONFIG_CMD_NAND
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_MAX_NAND_DEVICE		1
+#define CONFIG_SYS_NAND_BASE			ATMEL_BASE_CS3
+#define CONFIG_SYS_NAND_DBW_8
+/* our ALE is AD21 */
+#define CONFIG_SYS_NAND_MASK_ALE		(1 << 21)
+/* our CLE is AD22 */
+#define CONFIG_SYS_NAND_MASK_CLE		(1 << 22)
+#define CONFIG_SYS_NAND_ENABLE_PIN		AT91_PIN_PC14
+#define CONFIG_SYS_NAND_READY_PIN		AT91_PIN_PC13
+
+/* NOR flash - no real flash on this board */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_FAT
+
+#define CONFIG_SYS_LOAD_ADDR			0x22000000	/* load address */
+
+#define CONFIG_SYS_MEMTEST_START		CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END			0x23e00000
+
+/* Env in EEPROM, bootstrap + u-boot in NAND*/
+#ifdef CONFIG_ENV_IS_IN_EEPROM
+#define CONFIG_ENV_OFFSET		0x20
+#define CONFIG_ENV_SIZE		        0x1000
+#endif
+
+/* Env, bootstrap and u-boot in NAND */
+#ifdef CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET               0x60000
+#define CONFIG_ENV_OFFSET_REDUND        0x80000
+#define CONFIG_ENV_SIZE                 0x20000
+#endif
+
+#define CONFIG_BOOTCOMMAND	"nboot 0x21000000 0 400000"
+#define CONFIG_BOOTARGS		"console=ttyS0,115200 " \
+				"root=/dev/mtdblock1 " \
+				"mtdparts=atmel_nand:16M(kernel)ro," \
+				"120M(rootfs),-(other) " \
+				"rw rootfstype=jffs2"
+
+#define CONFIG_SYS_PROMPT	"U-Boot> "
+#define CONFIG_SYS_CBSIZE	256
+#define CONFIG_SYS_MAXARGS	16
+#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN	ROUND(3 * CONFIG_ENV_SIZE + 128 * 1024, 0x1000)
+
+#endif