Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

1 files changed, 175 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/include/configs/pm9g45.h b/qemu/roms/u-boot/include/configs/pm9g45.h
new file mode 100644
index 000000000..f78e0ec17
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/pm9g45.h
@@ -0,0 +1,175 @@
+/*
+ * (C) Copyright 2010
+ * Ilko Iliev <iliev@ronetix.at>
+ * Asen Dimov <dimov@ronetix.at>
+ * Ronetix GmbH <www.ronetix.at>
+ *
+ * (C) Copyright 2007-2008
+ * Stelian Pop <stelian@popies.net>
+ * Lead Tech Design <www.leadtechdesign.com>
+ *
+ * Configuation settings for the PM9G45 board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * SoC must be defined first, before hardware.h is included.
+ * In this case SoC is defined in boards.cfg.
+ */
+#include <asm/hardware.h>
+
+#define CONFIG_PM9G45		1	/* It's an Ronetix PM9G45 */
+#define CONFIG_SYS_AT91_CPU_NAME	"AT91SAM9G45"
+
+#define MACH_TYPE_PM9G45	2672
+#define CONFIG_MACH_TYPE	MACH_TYPE_PM9G45
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_MAIN_CLOCK	12000000 /* from 12 MHz crystal */
+#define CONFIG_SYS_AT91_SLOW_CLOCK	32768		/* slow clock xtal */
+#define CONFIG_SYS_TEXT_BASE		0x73f00000
+
+#define CONFIG_ARCH_CPU_INIT
+
+#define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG	1
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_AT91_GPIO	1
+#define CONFIG_ATMEL_USART	1
+#define CONFIG_USART_BASE		ATMEL_BASE_DBGU
+#define	CONFIG_USART_ID			ATMEL_ID_SYS
+
+#define CONFIG_SYS_USE_NANDFLASH	1
+
+/* LED */
+#define CONFIG_AT91_LED
+#define CONFIG_RED_LED		GPIO_PIN_PD(31) /* this is the user1 led */
+#define CONFIG_GREEN_LED	GPIO_PIN_PD(0)  /* this is the user2 led */
+
+#define CONFIG_BOOTDELAY	3
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE	1
+#define CONFIG_BOOTP_BOOTPATH		1
+#define CONFIG_BOOTP_GATEWAY		1
+#define CONFIG_BOOTP_HOSTNAME		1
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_PING		1
+#define CONFIG_CMD_DHCP		1
+#define CONFIG_CMD_NAND		1
+#define CONFIG_CMD_USB		1
+
+#define CONFIG_CMD_JFFS2		1
+#define CONFIG_JFFS2_CMDLINE		1
+#define CONFIG_JFFS2_NAND		1
+#define CONFIG_JFFS2_DEV		"nand0" /* NAND dev jffs2 lives on */
+#define CONFIG_JFFS2_PART_OFFSET	0	/* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_SIZE		(256 * 1024 * 1024) /* partition */
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			0x70000000
+#define PHYS_SDRAM_SIZE			0x08000000	/* 128 megs */
+
+/* NOR flash, not available */
+#define CONFIG_SYS_NO_FLASH		1
+#undef CONFIG_CMD_FLASH
+
+/* NAND flash */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		0x40000000
+#define CONFIG_SYS_NAND_DBW_8		1
+/* our ALE is AD21 */
+#define CONFIG_SYS_NAND_MASK_ALE	(1 << 21)
+/* our CLE is AD22 */
+#define CONFIG_SYS_NAND_MASK_CLE	(1 << 22)
+#define CONFIG_SYS_NAND_ENABLE_PIN	GPIO_PIN_PC(14)
+#define CONFIG_SYS_NAND_READY_PIN	GPIO_PIN_PD(3)
+
+#endif
+
+/* Ethernet */
+#define CONFIG_MACB			1
+#define CONFIG_RMII			1
+#define CONFIG_NET_RETRY_COUNT		20
+#define CONFIG_RESET_PHY_R		1
+
+/* USB */
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
+#define CONFIG_USB_OHCI_NEW		1
+#define CONFIG_DOS_PARTITION		1
+#define CONFIG_SYS_USB_OHCI_CPU_INIT	1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE	0x00700000 /* _UHP_OHCI_BASE */
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME	"at91sam9g45"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
+#define CONFIG_USB_STORAGE		1
+
+/* board specific(not enough SRAM) */
+#define CONFIG_AT91SAM9G45_LCD_BASE	PHYS_SDRAM + 0xE00000
+
+#define CONFIG_SYS_LOAD_ADDR		PHYS_SDRAM + 0x2000000 /* load addr */
+
+#define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM
+#define CONFIG_SYS_MEMTEST_END		CONFIG_AT91SAM9G45_LCD_BASE
+
+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND		1
+#define CONFIG_ENV_OFFSET		0x60000
+#define CONFIG_ENV_OFFSET_REDUND	0x80000
+#define CONFIG_ENV_SIZE			0x20000		/* 1 sector = 128 kB */
+#define CONFIG_BOOTCOMMAND	"nand read 0x72000000 0x200000 0x200000; bootm"
+#define CONFIG_BOOTARGS		"fbcon=rotate:3 console=tty0 " \
+				"console=ttyS0,115200 " \
+				"root=/dev/mtdblock4 " \
+				"mtdparts=atmel_nand:128k(bootstrap)ro," \
+				"256k(uboot)ro,1664k(env)," \
+				"2M(linux)ro,-(root) rw " \
+				"rootfstype=jffs2"
+
+#define CONFIG_BAUDRATE			115200
+
+#define CONFIG_SYS_PROMPT		"U-Boot> "
+#define CONFIG_SYS_CBSIZE		256
+#define CONFIG_SYS_MAXARGS		16
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP		1
+#define CONFIG_CMDLINE_EDITING		1
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_HUSH_PARSER
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN		ROUND(3 * CONFIG_ENV_SIZE + 128*1024,\
+					0x1000)
+
+#define CONFIG_SYS_SDRAM_BASE	PHYS_SDRAM
+#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_SDRAM_BASE + 0x1000 - \
+				GENERATED_GBL_DATA_SIZE)
+
+#endif