Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

1 files changed, 274 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/include/configs/VOM405.h b/qemu/roms/u-boot/include/configs/VOM405.h
new file mode 100644
index 000000000..c06897b89
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/VOM405.h
@@ -0,0 +1,274 @@
+/*
+ * (C) Copyright 2001-2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
+#define CONFIG_VOM405		1	/* ...on a VOM405 board		*/
+
+#define	CONFIG_SYS_TEXT_BASE	0xFFFC8000
+
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
+#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
+
+#define CONFIG_SYS_CLK_FREQ	33330000 /* external frequency to pll	*/
+
+#define CONFIG_BAUDRATE		9600
+#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
+
+#undef	CONFIG_BOOTARGS
+#undef  CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT                  /* enable preboot variable      */
+
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#undef  CONFIG_HAS_ETH1
+
+#define CONFIG_PPC4xx_EMAC
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_EEPROM
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+
+#undef  CONFIG_PRAM			/* no "protected RAM"           */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
+
+#undef	CONFIG_SYS_HUSH_PARSER			/* use "hush" command parser	*/
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CONFIG_SYS_DEVICE_NULLDEV	1	/* include nulldev device	*/
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
+
+#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
+
+#undef	CONFIG_SYS_EXT_SERIAL_CLOCK	       /* no external serial clock used */
+#define CONFIG_SYS_BASE_BAUD	    691200
+
+/* The following table includes the supported baudrates */
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
+	 57600, 115200, 230400, 460800, 921600 }
+
+#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
+#define CONFIG_SYS_EXTBDINFO	1		/* To use extended board_into (bd_t) */
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+
+#define CONFIG_SYS_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+/*
+ * FLASH organization
+ */
+#define FLASH_BASE0_PRELIM	0xFFC00000	/* FLASH bank #0	*/
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
+
+#define CONFIG_SYS_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CONFIG_SYS_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CONFIG_SYS_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CONFIG_SYS_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CONFIG_SYS_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CONFIG_SYS_FLASH_READ2		0x0002	/* 2 is standard			*/
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+
+/*
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN		(~(CONFIG_SYS_TEXT_BASE) + 1)
+#define CONFIG_SYS_MALLOC_LEN		(256 * 1024)
+
+#if (CONFIG_SYS_MONITOR_BASE < FLASH_BASE0_PRELIM)
+# define CONFIG_SYS_RAMBOOT		1
+#else
+# undef CONFIG_SYS_RAMBOOT
+#endif
+
+/*
+ * Environment Variable setup
+ */
+#define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CONFIG_ENV_OFFSET		0x100	/* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
+				   /* total size of a CAT24WC16 is 2048 bytes */
+
+#define CONFIG_SYS_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
+#define CONFIG_SYS_NVRAM_SIZE		242			/* NVRAM size		*/
+
+/*
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
+					/* 16 byte page write mode using*/
+					/* last 4 bits of the address	*/
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
+
+/*
+ * External Bus Controller (EBC) Setup
+ */
+#define CAN_BA		0xF0000000	    /* CAN Base Address			*/
+
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization			*/
+#define CONFIG_SYS_EBC_PB0AP		0x92015480
+#define CONFIG_SYS_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization		*/
+#define CONFIG_SYS_EBC_PB2AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CONFIG_SYS_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
+
+/*
+ * FPGA stuff
+ */
+#define CONFIG_SYS_XSVF_DEFAULT_ADDR	0xfffc0000
+
+/* FPGA program pin configuration */
+#define CONFIG_SYS_FPGA_PRG		0x04000000  /* JTAG TMS pin (ppc output)     */
+#define CONFIG_SYS_FPGA_CLK		0x02000000  /* JTAG TCK pin (ppc output)     */
+#define CONFIG_SYS_FPGA_DATA		0x01000000  /* JTAG TDO->TDI data pin (ppc output) */
+#define CONFIG_SYS_FPGA_INIT		0x00010000  /* unused (ppc input)	     */
+#define CONFIG_SYS_FPGA_DONE		0x00008000  /* JTAG TDI->TDO pin (ppc input) */
+
+/*
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CONFIG_SYS_TEMP_STACK_OCM	  1
+
+/* On Chip Memory location */
+#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
+#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
+#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM	*/
+
+#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+/*
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * GPIO0[0]	- External Bus Controller BLAST output
+ * GPIO0[1-9]	- Instruction trace outputs -> GPIO
+ * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
+ * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
+ * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
+ * GPIO0[24-27] - UART0 control signal inputs/outputs
+ * GPIO0[28-29] - UART1 data signal input/output
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ */
+/* GPIO Input:		OSR=00, ISR=00, TSR=00, TCR=0 */
+/* GPIO Output:		OSR=00, ISR=00, TSR=00, TCR=1 */
+/* Alt. Funtion Input:	OSR=00, ISR=01, TSR=00, TCR=0 */
+/* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */
+#define CONFIG_SYS_GPIO0_OSRL		0x40000500  /*	0 ... 15 */
+#define CONFIG_SYS_GPIO0_OSRH		0x00000110  /* 16 ... 31 */
+#define CONFIG_SYS_GPIO0_ISR1L		0x00000000  /*	0 ... 15 */
+#define CONFIG_SYS_GPIO0_ISR1H		0x14000045  /* 16 ... 31 */
+#define CONFIG_SYS_GPIO0_TSRL		0x00000000  /*	0 ... 15 */
+#define CONFIG_SYS_GPIO0_TSRH		0x00000000  /* 16 ... 31 */
+#define CONFIG_SYS_GPIO0_TCR		0xF7FE0014  /*	0 ... 31 */
+
+/*
+ * Default speed selection (cpu_plb_opb_ebc) in mhz.
+ * This value will be set if iic boot eprom is disabled.
+ */
+#define PLLMR0_DEFAULT	 PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT	 PLLMR1_133_66_66_33
+
+#endif	/* __CONFIG_H */