Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

1 files changed, 237 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/include/configs/CPCIISER4.h b/qemu/roms/u-boot/include/configs/CPCIISER4.h
new file mode 100644
index 000000000..25365f747
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/CPCIISER4.h
@@ -0,0 +1,237 @@
+/*
+ * (C) Copyright 2001-2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
+#define CONFIG_CPCIISER4	1	/* ...on a CPCIISER4 board	*/
+
+#define	CONFIG_SYS_TEXT_BASE	0xFFFC0000
+
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
+
+#define CONFIG_SYS_CLK_FREQ	25000000 /* external frequency to pll	*/
+
+#define CONFIG_BAUDRATE		9600
+#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
+
+#undef	CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND	"bootm fff00000"
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_PPC4xx_EMAC
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_EEPROM
+
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
+
+#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
+
+#define CONFIG_SYS_EXT_SERIAL_CLOCK	1843200	 /* use external serial clock	*/
+
+/* The following table includes the supported baudrates */
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
+	 57600, 115200, 230400, 460800, 921600 }
+
+#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
+#define CONFIG_SYS_EXTBDINFO	1		/* To use extended board_into (bd_t) */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0		/* configure ar pci adapter	*/
+#define PCI_HOST_FORCE	1		/* configure as pci host	*/
+#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
+
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO	/* select pci host function	*/
+#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+					/* resource configuration	*/
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0404	/* PCI Device ID: CPCI-ISER4	*/
+#define CONFIG_SYS_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CONFIG_SYS_PCI_PTM1MS	0xff000001	/* 16MB, enable hard-wired to 1 */
+#define CONFIG_SYS_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CONFIG_SYS_PCI_PTM2LA	0xffe00000	/* point to flash		*/
+#define CONFIG_SYS_PCI_PTM2MS	0xffe00001	/* 2MB, enable			*/
+#define CONFIG_SYS_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_FLASH_BASE		0xFFFC0000
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
+#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define CONFIG_SYS_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CONFIG_SYS_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CONFIG_SYS_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CONFIG_SYS_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CONFIG_SYS_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CONFIG_SYS_FLASH_READ2		0x0002	/* 2 is standard			*/
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC08) for environment
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
+					/* 16 byte page write mode using*/
+					/* last 4 bits of the address	*/
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
+
+#define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CONFIG_ENV_OFFSET		0x000	/* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_SIZE		0x300	/* 768 bytes may be used for env vars */
+				   /* total size of a CAT24WC08 is 1024 bytes */
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM	0xFFF00000	/* FLASH bank #0	*/
+#define FLASH_BASE1_PRELIM	0		/* FLASH bank #1	*/
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+/* Memory Bank 0 (Flash Bank 0) initialization					*/
+#define CONFIG_SYS_EBC_PB0AP		0x92015480
+#define CONFIG_SYS_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 1 (Uart 8bit) initialization					*/
+#define CONFIG_SYS_EBC_PB1AP		0x01000480  /* TWT=2,TH=2,no Ready,BEM=0,SOR=1	*/
+#define CONFIG_SYS_EBC_PB1CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
+
+/* Memory Bank 2 (Uart 32bit) initialization					*/
+#define CONFIG_SYS_EBC_PB2AP		0x000004c0  /* no Ready, BEM=1			*/
+#define CONFIG_SYS_EBC_PB2CR		0xF011C000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=32bit */
+
+/* Memory Bank 3 (FPGA Reset) initialization					*/
+#define CONFIG_SYS_EBC_PB3AP		0x010004C0  /* no Ready, BEM=1			*/
+#define CONFIG_SYS_EBC_PB3CR		0xF021A000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=16bit */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CONFIG_SYS_INIT_DCACHE_CS	7	/* use cs # 7 for data cache memory    */
+#define CONFIG_SYS_INIT_RAM_ADDR	0x40000000  /* use data cache		       */
+#define CONFIG_SYS_INIT_RAM_SIZE	0x2000	/* Size of used area in RAM	       */
+#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#endif	/* __CONFIG_H */