Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

1 files changed, 174 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/doc/README.at91 b/qemu/roms/u-boot/doc/README.at91
new file mode 100644
index 000000000..67412136e
--- /dev/null
+++ b/qemu/roms/u-boot/doc/README.at91
@@ -0,0 +1,174 @@
+Atmel AT91 Evaluation kits
+
+Index
+  - I. Board mapping & boot media
+  - II. NAND partition table
+  - III. watchdog support
+
+I. Board mapping & boot media
+------------------------------------------------------------------------------
+AT91SAM9260EK, AT91SAM9G20EK & AT91SAM9XEEK
+------------------------------------------------------------------------------
+
+Memory map
+	0x20000000 - 23FFFFFF	SDRAM (64 MB)
+	0xC0000000 - Cxxxxxxx	Atmel Dataflash card (J13)
+	0xD0000000 - D07FFFFF	Soldered Atmel Dataflash (AT45DB642)
+
+Environment variables
+
+	U-Boot environment variables can be stored at different places:
+		- Dataflash on SPI chip select 1 (default)
+		- Dataflash on SPI chip select 0 (dataflash card)
+		- Nand flash.
+
+	You can choose your storage location at config step (here for at91sam9260ek) :
+		make at91sam9260ek_nandflash_config	- use nand flash
+		make at91sam9260ek_dataflash_cs0_config	- use data flash (spi cs0)
+		make at91sam9260ek_dataflash_cs1_config	- use data flash (spi cs1)
+
+
+------------------------------------------------------------------------------
+AT91SAM9261EK, AT91SAM9G10EK
+------------------------------------------------------------------------------
+
+Memory map
+	0x20000000 - 23FFFFFF	SDRAM (64 MB)
+	0xC0000000 - C07FFFFF	Soldered Atmel Dataflash (AT45DB642)
+	0xD0000000 - Dxxxxxxx	Atmel Dataflash card (J22)
+
+Environment variables
+
+	U-Boot environment variables can be stored at different places:
+		- Dataflash on SPI chip select 0 (default)
+		- Dataflash on SPI chip select 3 (dataflash card)
+		- Nand flash.
+
+	You can choose your storage location at config step (here for at91sam9260ek) :
+		make at91sam9261ek_nandflash_config	- use nand flash
+		make at91sam9261ek_dataflash_cs0_config	- use data flash (spi cs0)
+		make at91sam9261ek_dataflash_cs3_config	- use data flash (spi cs3)
+
+
+------------------------------------------------------------------------------
+AT91SAM9263EK
+------------------------------------------------------------------------------
+
+Memory map
+	0x20000000 - 23FFFFFF	SDRAM (64 MB)
+	0xC0000000 - Cxxxxxxx	Atmel Dataflash card (J9)
+
+Environment variables
+
+	U-Boot environment variables can be stored at different places:
+		- Dataflash on SPI chip select 0 (dataflash card)
+		- Nand flash.
+		- Nor flash (not populate by default)
+
+	You can choose your storage location at config step (here for at91sam9260ek) :
+		make at91sam9263ek_nandflash_config	- use nand flash
+		make at91sam9263ek_dataflash_cs0_config	- use data flash (spi cs0)
+		make at91sam9263ek_norflash_config	- use nor flash
+
+	You can choose to boot directly from U-Boot at config step
+		make at91sam9263ek_norflash_boot_config	- boot from nor flash
+
+
+------------------------------------------------------------------------------
+AT91SAM9M10G45EK
+------------------------------------------------------------------------------
+
+Memory map
+	0x70000000 - 77FFFFFF	SDRAM (128 MB)
+
+Environment variables
+
+	U-Boot environment variables can be stored at different places:
+		- Nand flash.
+
+	You can choose your storage location at config step (here for at91sam9m10g45ek) :
+		make at91sam9m10g45ek_nandflash_config		- use nand flash
+
+
+------------------------------------------------------------------------------
+AT91SAM9RLEK
+------------------------------------------------------------------------------
+
+Memory map
+	0x20000000 - 23FFFFFF	SDRAM (64 MB)
+	0xC0000000 - C07FFFFF   Soldered Atmel Dataflash (AT45DB642)
+
+Environment variables
+
+	U-Boot environment variables can be stored at different places:
+		- Dataflash on SPI chip select 0
+		- Nand flash.
+
+	You can choose your storage location at config step (here for at91sam9rlek) :
+		make at91sam9rlek_nandflash_config	- use nand flash
+
+
+------------------------------------------------------------------------------
+AT91SAM9N12EK, AT91SAM9X5EK
+------------------------------------------------------------------------------
+
+Memory map
+	0x20000000 - 27FFFFFF	SDRAM (128 MB)
+
+Environment variables
+
+	U-Boot environment variables can be stored at different places:
+		- Nand flash.
+		- SD/MMC card
+		- Serialflash/Dataflash on SPI chip select 0
+
+	You can choose your storage location at config step (here for at91sam9x5ek) :
+		make at91sam9x5ek_dataflash_config	- use data flash
+		make at91sam9x5ek_mmc_config		- use sd/mmc card
+		make at91sam9x5ek_nandflash_config	- use nand flash
+		make at91sam9x5ek_spiflash_config	- use serial flash
+
+
+------------------------------------------------------------------------------
+SAMA5D3XEK
+------------------------------------------------------------------------------
+
+Memory map
+	0x20000000 - 3FFFFFFF	SDRAM (512 MB)
+
+Environment variables
+
+	U-Boot environment variables can be stored at different places:
+		- Nand flash.
+		- SD/MMC card
+		- Serialflash on SPI chip select 0
+
+	You can choose your storage location at config step (here for sama5d3xek) :
+		make sama5d3xek_mmc_config		- use SD/MMC card
+		make sama5d3xek_nandflash_config	- use nand flash
+		make sama5d3xek_serialflash_config	- use serial flash
+
+
+II. NAND partition table
+
+	All the board support boot from NAND flash will use the following NAND
+	partition table
+
+		0x00000000 - 0x0003FFFF	bootstrap	(256 KiB)
+		0x00040000 - 0x000BFFFF u-boot		(512 KiB)
+		0x000C0000 - 0x000FFFFF env		(256 KiB)
+		0x00100000 - 0x0013FFFF env_redundant	(256 KiB)
+		0x00140000 - 0x0017FFFF spare		(256 KiB)
+		0x00180000 - 0x001FFFFF dtb		(512 KiB)
+		0x00200000 - 0x007FFFFF kernel		(6 MiB)
+		0x00800000 - 0xxxxxxxxx rootfs		(All left)
+
+III. Watchdog support
+
+	For security reasons, the at91 watchdog is running at boot time and,
+	if deactivated, cannot be used anymore.
+	If you want to use the watchdog, you will need to keep it running in
+	your code (make sure not to disable it in AT91Bootstrap for instance).
+
+	In the U-Boot configuration, the AT91 watchdog support is enabled using
+	the CONFIG_AT91SAM9_WATCHDOG and CONFIG_HW_WATCHDOG options.