Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

1 files changed, 553 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/board/ti/beagle/beagle.c b/qemu/roms/u-boot/board/ti/beagle/beagle.c
new file mode 100644
index 000000000..0674afdc0
--- /dev/null
+++ b/qemu/roms/u-boot/board/ti/beagle/beagle.c
@@ -0,0 +1,553 @@
+/*
+ * (C) Copyright 2004-2011
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ *	Sunil Kumar <sunilsaini05@gmail.com>
+ *	Shashi Ranjan <shashiranjanmca05@gmail.com>
+ *
+ * Derived from Beagle Board and 3430 SDP code by
+ *	Richard Woodruff <r-woodruff2@ti.com>
+ *	Syed Mohammed Khasim <khasim@ti.com>
+ *
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#include <common.h>
+#ifdef CONFIG_STATUS_LED
+#include <status_led.h>
+#endif
+#include <twl4030.h>
+#include <linux/mtd/nand.h>
+#include <asm/io.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/mach-types.h>
+#include <asm/omap_musb.h>
+#include <asm/errno.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+#include <linux/usb/musb.h>
+#include "beagle.h"
+#include <command.h>
+
+#ifdef CONFIG_USB_EHCI
+#include <usb.h>
+#include <asm/ehci-omap.h>
+#endif
+
+#define TWL4030_I2C_BUS			0
+#define EXPANSION_EEPROM_I2C_BUS	1
+#define EXPANSION_EEPROM_I2C_ADDRESS	0x50
+
+#define TINCANTOOLS_ZIPPY		0x01000100
+#define TINCANTOOLS_ZIPPY2		0x02000100
+#define TINCANTOOLS_TRAINER		0x04000100
+#define TINCANTOOLS_SHOWDOG		0x03000100
+#define KBADC_BEAGLEFPGA		0x01000600
+#define LW_BEAGLETOUCH			0x01000700
+#define BRAINMUX_LCDOG			0x01000800
+#define BRAINMUX_LCDOGTOUCH		0x02000800
+#define BBTOYS_WIFI			0x01000B00
+#define BBTOYS_VGA			0x02000B00
+#define BBTOYS_LCD			0x03000B00
+#define BCT_BRETTL3			0x01000F00
+#define BCT_BRETTL4			0x02000F00
+#define LSR_COM6L_ADPT			0x01001300
+#define BEAGLE_NO_EEPROM		0xffffffff
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct {
+	unsigned int device_vendor;
+	unsigned char revision;
+	unsigned char content;
+	char fab_revision[8];
+	char env_var[16];
+	char env_setting[64];
+} expansion_config;
+
+/*
+ * Routine: board_init
+ * Description: Early hardware init.
+ */
+int board_init(void)
+{
+	gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+	/* board id for Linux */
+	gd->bd->bi_arch_number = MACH_TYPE_OMAP3_BEAGLE;
+	/* boot param addr */
+	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
+	status_led_set (STATUS_LED_BOOT, STATUS_LED_ON);
+#endif
+
+	return 0;
+}
+
+/*
+ * Routine: get_board_revision
+ * Description: Detect if we are running on a Beagle revision Ax/Bx,
+ *		C1/2/3, C4, xM Ax/Bx or xM Cx. This can be done by reading
+ *		the level of GPIO173, GPIO172 and GPIO171. This should
+ *		result in
+ *		GPIO173, GPIO172, GPIO171: 1 1 1 => Ax/Bx
+ *		GPIO173, GPIO172, GPIO171: 1 1 0 => C1/2/3
+ *		GPIO173, GPIO172, GPIO171: 1 0 1 => C4
+ *		GPIO173, GPIO172, GPIO171: 0 1 0 => xM Cx
+ *		GPIO173, GPIO172, GPIO171: 0 0 0 => xM Ax/Bx
+ */
+static int get_board_revision(void)
+{
+	int revision;
+
+	if (!gpio_request(171, "") &&
+	    !gpio_request(172, "") &&
+	    !gpio_request(173, "")) {
+
+		gpio_direction_input(171);
+		gpio_direction_input(172);
+		gpio_direction_input(173);
+
+		revision = gpio_get_value(173) << 2 |
+			   gpio_get_value(172) << 1 |
+			   gpio_get_value(171);
+	} else {
+		printf("Error: unable to acquire board revision GPIOs\n");
+		revision = -1;
+	}
+
+	return revision;
+}
+
+#ifdef CONFIG_SPL_BUILD
+/*
+ * Routine: get_board_mem_timings
+ * Description: If we use SPL then there is no x-loader nor config header
+ * so we have to setup the DDR timings ourself on both banks.
+ */
+void get_board_mem_timings(struct board_sdrc_timings *timings)
+{
+	int pop_mfr, pop_id;
+
+	/*
+	 * We need to identify what PoP memory is on the board so that
+	 * we know what timings to use.  If we can't identify it then
+	 * we know it's an xM.  To map the ID values please see nand_ids.c
+	 */
+	identify_nand_chip(&pop_mfr, &pop_id);
+
+	timings->mr = MICRON_V_MR_165;
+	switch (get_board_revision()) {
+	case REVISION_C4:
+		if (pop_mfr == NAND_MFR_STMICRO && pop_id == 0xba) {
+			/* 512MB DDR */
+			timings->mcfg = NUMONYX_V_MCFG_165(512 << 20);
+			timings->ctrla = NUMONYX_V_ACTIMA_165;
+			timings->ctrlb = NUMONYX_V_ACTIMB_165;
+			timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+			break;
+		} else if (pop_mfr == NAND_MFR_MICRON && pop_id == 0xba) {
+			/* Beagleboard Rev C4, 512MB Nand/256MB DDR*/
+			timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+			timings->ctrla = MICRON_V_ACTIMA_165;
+			timings->ctrlb = MICRON_V_ACTIMB_165;
+			timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+			break;
+		} else if (pop_mfr == NAND_MFR_MICRON && pop_id == 0xbc) {
+			/* Beagleboard Rev C5, 256MB DDR */
+			timings->mcfg = MICRON_V_MCFG_200(256 << 20);
+			timings->ctrla = MICRON_V_ACTIMA_200;
+			timings->ctrlb = MICRON_V_ACTIMB_200;
+			timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+			break;
+		}
+	case REVISION_XM_AB:
+	case REVISION_XM_C:
+		if (pop_mfr == 0) {
+			/* 256MB DDR */
+			timings->mcfg = MICRON_V_MCFG_200(256 << 20);
+			timings->ctrla = MICRON_V_ACTIMA_200;
+			timings->ctrlb = MICRON_V_ACTIMB_200;
+			timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
+		} else {
+			/* 512MB DDR */
+			timings->mcfg = NUMONYX_V_MCFG_165(512 << 20);
+			timings->ctrla = NUMONYX_V_ACTIMA_165;
+			timings->ctrlb = NUMONYX_V_ACTIMB_165;
+			timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+		}
+		break;
+	default:
+		/* Assume 128MB and Micron/165MHz timings to be safe */
+		timings->mcfg = MICRON_V_MCFG_165(128 << 20);
+		timings->ctrla = MICRON_V_ACTIMA_165;
+		timings->ctrlb = MICRON_V_ACTIMB_165;
+		timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+	}
+}
+#endif
+
+/*
+ * Routine: get_expansion_id
+ * Description: This function checks for expansion board by checking I2C
+ *		bus 1 for the availability of an AT24C01B serial EEPROM.
+ *		returns the device_vendor field from the EEPROM
+ */
+static unsigned int get_expansion_id(void)
+{
+	i2c_set_bus_num(EXPANSION_EEPROM_I2C_BUS);
+
+	/* return BEAGLE_NO_EEPROM if eeprom doesn't respond */
+	if (i2c_probe(EXPANSION_EEPROM_I2C_ADDRESS) == 1) {
+		i2c_set_bus_num(TWL4030_I2C_BUS);
+		return BEAGLE_NO_EEPROM;
+	}
+
+	/* read configuration data */
+	i2c_read(EXPANSION_EEPROM_I2C_ADDRESS, 0, 1, (u8 *)&expansion_config,
+		 sizeof(expansion_config));
+
+	/* retry reading configuration data with 16bit addressing */
+	if ((expansion_config.device_vendor == 0xFFFFFF00) ||
+	    (expansion_config.device_vendor == 0xFFFFFFFF)) {
+		printf("EEPROM is blank or 8bit addressing failed: retrying with 16bit:\n");
+		i2c_read(EXPANSION_EEPROM_I2C_ADDRESS, 0, 2, (u8 *)&expansion_config,
+			 sizeof(expansion_config));
+	}
+
+	i2c_set_bus_num(TWL4030_I2C_BUS);
+
+	return expansion_config.device_vendor;
+}
+
+#ifdef CONFIG_VIDEO_OMAP3
+/*
+ * Configure DSS to display background color on DVID
+ * Configure VENC to display color bar on S-Video
+ */
+static void beagle_display_init(void)
+{
+	omap3_dss_venc_config(&venc_config_std_tv, VENC_HEIGHT, VENC_WIDTH);
+	switch (get_board_revision()) {
+	case REVISION_AXBX:
+	case REVISION_CX:
+	case REVISION_C4:
+		omap3_dss_panel_config(&dvid_cfg);
+		break;
+	case REVISION_XM_AB:
+	case REVISION_XM_C:
+	default:
+		omap3_dss_panel_config(&dvid_cfg_xm);
+		break;
+	}
+}
+
+/*
+ * Enable DVI power
+ */
+static void beagle_dvi_pup(void)
+{
+	uchar val;
+
+	switch (get_board_revision()) {
+	case REVISION_AXBX:
+	case REVISION_CX:
+	case REVISION_C4:
+		gpio_request(170, "");
+		gpio_direction_output(170, 0);
+		gpio_set_value(170, 1);
+		break;
+	case REVISION_XM_AB:
+	case REVISION_XM_C:
+	default:
+		#define GPIODATADIR1 (TWL4030_BASEADD_GPIO+3)
+		#define GPIODATAOUT1 (TWL4030_BASEADD_GPIO+6)
+
+		i2c_read(TWL4030_CHIP_GPIO, GPIODATADIR1, 1, &val, 1);
+		val |= 4;
+		i2c_write(TWL4030_CHIP_GPIO, GPIODATADIR1, 1, &val, 1);
+
+		i2c_read(TWL4030_CHIP_GPIO, GPIODATAOUT1, 1, &val, 1);
+		val |= 4;
+		i2c_write(TWL4030_CHIP_GPIO, GPIODATAOUT1, 1, &val, 1);
+		break;
+	}
+}
+#endif
+
+#ifdef CONFIG_USB_MUSB_OMAP2PLUS
+static struct musb_hdrc_config musb_config = {
+	.multipoint     = 1,
+	.dyn_fifo       = 1,
+	.num_eps        = 16,
+	.ram_bits       = 12,
+};
+
+static struct omap_musb_board_data musb_board_data = {
+	.interface_type	= MUSB_INTERFACE_ULPI,
+};
+
+static struct musb_hdrc_platform_data musb_plat = {
+#if defined(CONFIG_MUSB_HOST)
+	.mode           = MUSB_HOST,
+#elif defined(CONFIG_MUSB_GADGET)
+	.mode		= MUSB_PERIPHERAL,
+#else
+#error "Please define either CONFIG_MUSB_HOST or CONFIG_MUSB_GADGET"
+#endif
+	.config         = &musb_config,
+	.power          = 100,
+	.platform_ops	= &omap2430_ops,
+	.board_data	= &musb_board_data,
+};
+#endif
+
+/*
+ * Routine: misc_init_r
+ * Description: Configure board specific parts
+ */
+int misc_init_r(void)
+{
+	struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
+	struct gpio *gpio6_base = (struct gpio *)OMAP34XX_GPIO6_BASE;
+	struct control_prog_io *prog_io_base = (struct control_prog_io *)OMAP34XX_CTRL_BASE;
+	bool generate_fake_mac = false;
+
+	/* Enable i2c2 pullup resisters */
+	writel(~(PRG_I2C2_PULLUPRESX), &prog_io_base->io1);
+
+	switch (get_board_revision()) {
+	case REVISION_AXBX:
+		printf("Beagle Rev Ax/Bx\n");
+		setenv("beaglerev", "AxBx");
+		break;
+	case REVISION_CX:
+		printf("Beagle Rev C1/C2/C3\n");
+		setenv("beaglerev", "Cx");
+		MUX_BEAGLE_C();
+		break;
+	case REVISION_C4:
+		printf("Beagle Rev C4\n");
+		setenv("beaglerev", "C4");
+		MUX_BEAGLE_C();
+		/* Set VAUX2 to 1.8V for EHCI PHY */
+		twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
+					TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
+					TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
+					TWL4030_PM_RECEIVER_DEV_GRP_P1);
+		break;
+	case REVISION_XM_AB:
+		printf("Beagle xM Rev A/B\n");
+		setenv("beaglerev", "xMAB");
+		MUX_BEAGLE_XM();
+		/* Set VAUX2 to 1.8V for EHCI PHY */
+		twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
+					TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
+					TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
+					TWL4030_PM_RECEIVER_DEV_GRP_P1);
+		generate_fake_mac = true;
+		break;
+	case REVISION_XM_C:
+		printf("Beagle xM Rev C\n");
+		setenv("beaglerev", "xMC");
+		MUX_BEAGLE_XM();
+		/* Set VAUX2 to 1.8V for EHCI PHY */
+		twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
+					TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
+					TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
+					TWL4030_PM_RECEIVER_DEV_GRP_P1);
+		generate_fake_mac = true;
+		break;
+	default:
+		printf("Beagle unknown 0x%02x\n", get_board_revision());
+		MUX_BEAGLE_XM();
+		/* Set VAUX2 to 1.8V for EHCI PHY */
+		twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
+					TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
+					TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
+					TWL4030_PM_RECEIVER_DEV_GRP_P1);
+		generate_fake_mac = true;
+	}
+
+	switch (get_expansion_id()) {
+	case TINCANTOOLS_ZIPPY:
+		printf("Recognized Tincantools Zippy board (rev %d %s)\n",
+			expansion_config.revision,
+			expansion_config.fab_revision);
+		MUX_TINCANTOOLS_ZIPPY();
+		setenv("buddy", "zippy");
+		break;
+	case TINCANTOOLS_ZIPPY2:
+		printf("Recognized Tincantools Zippy2 board (rev %d %s)\n",
+			expansion_config.revision,
+			expansion_config.fab_revision);
+		MUX_TINCANTOOLS_ZIPPY();
+		setenv("buddy", "zippy2");
+		break;
+	case TINCANTOOLS_TRAINER:
+		printf("Recognized Tincantools Trainer board (rev %d %s)\n",
+			expansion_config.revision,
+			expansion_config.fab_revision);
+		MUX_TINCANTOOLS_ZIPPY();
+		MUX_TINCANTOOLS_TRAINER();
+		setenv("buddy", "trainer");
+		break;
+	case TINCANTOOLS_SHOWDOG:
+		printf("Recognized Tincantools Showdow board (rev %d %s)\n",
+			expansion_config.revision,
+			expansion_config.fab_revision);
+		/* Place holder for DSS2 definition for showdog lcd */
+		setenv("defaultdisplay", "showdoglcd");
+		setenv("buddy", "showdog");
+		break;
+	case KBADC_BEAGLEFPGA:
+		printf("Recognized KBADC Beagle FPGA board\n");
+		MUX_KBADC_BEAGLEFPGA();
+		setenv("buddy", "beaglefpga");
+		break;
+	case LW_BEAGLETOUCH:
+		printf("Recognized Liquidware BeagleTouch board\n");
+		setenv("buddy", "beagletouch");
+		break;
+	case BRAINMUX_LCDOG:
+		printf("Recognized Brainmux LCDog board\n");
+		setenv("buddy", "lcdog");
+		break;
+	case BRAINMUX_LCDOGTOUCH:
+		printf("Recognized Brainmux LCDog Touch board\n");
+		setenv("buddy", "lcdogtouch");
+		break;
+	case BBTOYS_WIFI:
+		printf("Recognized BeagleBoardToys WiFi board\n");
+		MUX_BBTOYS_WIFI()
+		setenv("buddy", "bbtoys-wifi");
+		break;;
+	case BBTOYS_VGA:
+		printf("Recognized BeagleBoardToys VGA board\n");
+		break;;
+	case BBTOYS_LCD:
+		printf("Recognized BeagleBoardToys LCD board\n");
+		break;;
+	case BCT_BRETTL3:
+		printf("Recognized bct electronic GmbH brettl3 board\n");
+		break;
+	case BCT_BRETTL4:
+		printf("Recognized bct electronic GmbH brettl4 board\n");
+		break;
+	case LSR_COM6L_ADPT:
+		printf("Recognized LSR COM6L Adapter Board\n");
+		MUX_BBTOYS_WIFI()
+		setenv("buddy", "lsr-com6l-adpt");
+		break;
+	case BEAGLE_NO_EEPROM:
+		printf("No EEPROM on expansion board\n");
+		setenv("buddy", "none");
+		break;
+	default:
+		printf("Unrecognized expansion board: %x\n",
+			expansion_config.device_vendor);
+		setenv("buddy", "unknown");
+	}
+
+	if (expansion_config.content == 1)
+		setenv(expansion_config.env_var, expansion_config.env_setting);
+
+	twl4030_power_init();
+	switch (get_board_revision()) {
+	case REVISION_XM_AB:
+		twl4030_led_init(TWL4030_LED_LEDEN_LEDBON);
+		break;
+	default:
+		twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
+		break;
+	}
+
+	/* Set GPIO states before they are made outputs */
+	writel(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1,
+		&gpio6_base->setdataout);
+	writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
+		GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
+
+	/* Configure GPIOs to output */
+	writel(~(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
+	writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
+		GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
+
+	dieid_num_r();
+
+#ifdef CONFIG_VIDEO_OMAP3
+	beagle_dvi_pup();
+	beagle_display_init();
+	omap3_dss_enable();
+#endif
+
+#ifdef CONFIG_USB_MUSB_OMAP2PLUS
+	musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE);
+#endif
+
+	if (generate_fake_mac) {
+		u32 id[4];
+
+		get_dieid(id);
+		usb_fake_mac_from_die_id(id);
+	}
+
+	return 0;
+}
+
+/*
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ *		hardware. Many pins need to be moved from protect to primary
+ *		mode.
+ */
+void set_muxconf_regs(void)
+{
+	MUX_BEAGLE();
+}
+
+#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
+int board_mmc_init(bd_t *bis)
+{
+	return omap_mmc_init(0, 0, 0, -1, -1);
+}
+#endif
+
+#if defined(CONFIG_USB_EHCI) && !defined(CONFIG_SPL_BUILD)
+/* Call usb_stop() before starting the kernel */
+void show_boot_progress(int val)
+{
+	if (val == BOOTSTAGE_ID_RUN_OS)
+		usb_stop();
+}
+
+static struct omap_usbhs_board_data usbhs_bdata = {
+	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED
+};
+
+int ehci_hcd_init(int index, enum usb_init_type init,
+		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+	return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
+}
+
+int ehci_hcd_stop(int index)
+{
+	return omap_ehci_hcd_stop();
+}
+
+#endif /* CONFIG_USB_EHCI */
+
+#if defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET)
+int board_eth_init(bd_t *bis)
+{
+	return usb_eth_initialize(bis);
+}
+#endif