Adding qemu as a submodule of KVMFORNFV

This Patch includes the changes to add qemu as a submodule to
kvmfornfv repo and make use of the updated latest qemu for the
execution of all testcase
Change-Id: I1280af507a857675c7f81d30c95255635667bdd7
Signed-off-by:RajithaY<rajithax.yerrumsetty@intel.com>

1 files changed, 0 insertions, 103 deletions

diff --git a/qemu/roms/u-boot/board/in-circuit/grasshopper/grasshopper.c b/qemu/roms/u-boot/board/in-circuit/grasshopper/grasshopper.c
deleted file mode 100644
index 340b71318..000000000
--- a/qemu/roms/u-boot/board/in-circuit/grasshopper/grasshopper.c
+++ /dev/null
@@ -1,103 +0,0 @@
-/*
- * Copyright (C) 2011
- * Corscience GmbH & Co.KG, Andreas Bießmann <biessmann@corscience.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#include <common.h>
-
-#include <asm/io.h>
-#include <asm/sdram.h>
-#include <asm/arch/clk.h>
-#include <asm/arch/hmatrix.h>
-#include <asm/arch/mmu.h>
-#include <asm/arch/portmux.h>
-#include <netdev.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = {
-	{
-		.virt_pgno	= CONFIG_SYS_FLASH_BASE >> PAGE_SHIFT,
-		.nr_pages	= CONFIG_SYS_FLASH_SIZE >> PAGE_SHIFT,
-		.phys		= (CONFIG_SYS_FLASH_BASE >> PAGE_SHIFT)
-				| MMU_VMR_CACHE_NONE,
-	}, {
-		.virt_pgno	= CONFIG_SYS_SDRAM_BASE >> PAGE_SHIFT,
-		.nr_pages	= EBI_SDRAM_SIZE >> PAGE_SHIFT,
-		.phys		= (CONFIG_SYS_SDRAM_BASE >> PAGE_SHIFT)
-				| MMU_VMR_CACHE_WRBACK,
-	},
-};
-
-static const struct sdram_config sdram_config = {
-	/* Dual MT48LC16M16A2-7E (or equal) */
-	.data_bits		= SDRAM_DATA_32BIT,
-	.row_bits		= 13,
-	.col_bits		= 9,
-	.bank_bits		= 2,
-	.cas			= 2,
-	.twr			= 2,
-	.trc			= 7,
-	.trp			= 2,
-	.trcd			= 2,
-	.tras			= 4,
-	.txsr			= 7,
-	/* 7.81 us */
-	.refresh_period		= (781 * (SDRAMC_BUS_HZ / 1000)) / 100000,
-};
-
-int board_early_init_f(void)
-{
-	/* Enable SDRAM in the EBI mux */
-	hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE));
-
-	portmux_enable_ebi(SDRAM_DATA_32BIT, 23, 0, PORTMUX_DRIVE_HIGH);
-	portmux_enable_usart0(PORTMUX_DRIVE_MIN);
-	portmux_enable_usart1(PORTMUX_DRIVE_MIN);
-#if defined(CONFIG_MACB)
-	/* set PHY reset and pwrdown to low */
-	portmux_select_gpio(PORTMUX_PORT_B, (1 << 29) | (1 << 30),
-		PORTMUX_DIR_OUTPUT | PORTMUX_INIT_LOW);
-	udelay(100);
-	/* release PHYs reset */
-	gpio_set_value(GPIO_PIN_PB(29), 1);
-
-	portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_LOW);
-#endif
-
-	return 0;
-}
-
-phys_size_t initdram(int board_type)
-{
-	unsigned long expected_size;
-	unsigned long actual_size;
-	void *sdram_base;
-
-	sdram_base = uncached(EBI_SDRAM_BASE);
-
-	expected_size = sdram_init(sdram_base, &sdram_config);
-	actual_size = get_ram_size(sdram_base, expected_size);
-
-	if (expected_size != actual_size)
-		printf("Warning: Only %lu of %lu MiB SDRAM is working\n",
-				actual_size >> 20, expected_size >> 20);
-
-	return actual_size;
-}
-
-int board_early_init_r(void)
-{
-	gd->bd->bi_phy_id[0] = 0x00;
-	return 0;
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bi)
-{
-	macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0, bi->bi_phy_id[0]);
-	return 0;
-}
-#endif
-/* vim: set noet ts=8: */