Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

6 files changed, 1248 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/board/icu862/Makefile b/qemu/roms/u-boot/board/icu862/Makefile
new file mode 100644
index 000000000..263f21b96
--- /dev/null
+++ b/qemu/roms/u-boot/board/icu862/Makefile
@@ -0,0 +1,8 @@
+#
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	= icu862.o flash.o pcmcia.o
diff --git a/qemu/roms/u-boot/board/icu862/flash.c b/qemu/roms/u-boot/board/icu862/flash.c
new file mode 100644
index 000000000..a84ab99f3
--- /dev/null
+++ b/qemu/roms/u-boot/board/icu862/flash.c
@@ -0,0 +1,575 @@
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <mpc8xx.h>
+
+flash_info_t	flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
+
+#if defined(CONFIG_ENV_IS_IN_FLASH)
+# ifndef  CONFIG_ENV_ADDR
+#  define CONFIG_ENV_ADDR	(CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
+# endif
+# ifndef  CONFIG_ENV_SIZE
+#  define CONFIG_ENV_SIZE	CONFIG_ENV_SECT_SIZE
+# endif
+# ifndef  CONFIG_ENV_SECT_SIZE
+#  define CONFIG_ENV_SECT_SIZE  CONFIG_ENV_SIZE
+# endif
+#endif
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size (vu_long *addr, flash_info_t *info);
+static int write_word (flash_info_t *info, ulong dest, ulong data);
+static void flash_get_offsets (ulong base, flash_info_t *info);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	volatile immap_t     *immap  = (immap_t *)CONFIG_SYS_IMMR;
+	volatile memctl8xx_t *memctl = &immap->im_memctl;
+	unsigned long size_b0;
+	int i;
+
+	/* Init: no FLASHes known */
+	for (i=0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i)
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+
+	/* Static FLASH Bank configuration here - FIXME XXX */
+
+	size_b0 = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
+
+	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
+		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
+			size_b0,
+			size_b0 >> 20);
+	}
+
+	/* Remap FLASH according to real size */
+	memctl->memc_or0 = CONFIG_SYS_OR_TIMING_FLASH | (-size_b0 & OR_AM_MSK);
+	memctl->memc_br0 = (CONFIG_SYS_FLASH_BASE & BR_BA_MSK) | BR_MS_GPCM | BR_V;
+
+	/* Re-do sizing to get full correct info */
+	size_b0 = flash_get_size((vu_long *)CONFIG_SYS_FLASH_BASE, &flash_info[0]);
+
+	flash_get_offsets (CONFIG_SYS_FLASH_BASE, &flash_info[0]);
+
+#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
+	/* monitor protection ON by default */
+	flash_protect(FLAG_PROTECT_SET,
+		      CONFIG_SYS_MONITOR_BASE,
+		      CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
+		      &flash_info[0]);
+#endif
+
+#ifdef	CONFIG_ENV_IS_IN_FLASH
+	/* ENV protection ON by default */
+	flash_protect(FLAG_PROTECT_SET,
+		      CONFIG_ENV_ADDR,
+		      CONFIG_ENV_ADDR+CONFIG_ENV_SIZE-1,
+		      &flash_info[0]);
+#endif
+
+	/* ICU862 Board has only one Flash Bank */
+	flash_info[0].size = size_b0;
+
+	return size_b0;
+
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void flash_get_offsets (ulong base, flash_info_t *info)
+{
+	int i;
+
+	/* set up sector start address table */
+	if (((info->flash_id & FLASH_TYPEMASK) == FLASH_AM040) ||
+		((info->flash_id & FLASH_TYPEMASK) == FLASH_AM033C)) {
+		/* set sector offsets for uniform sector type	*/
+		for (i = 0; i < info->sector_count; i++) {
+			info->start[i] = base + (i * 0x00040000);
+		}
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info  (flash_info_t *info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		puts ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_AMD:	puts ("AMD ");		break;
+	case FLASH_MAN_FUJ:	puts ("FUJITSU ");	break;
+	case FLASH_MAN_BM:	puts ("BRIGHT MICRO ");	break;
+	default:		puts ("Unknown Vendor "); break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_AM040:	puts ("29F040/29LV040 (4 Mbit, uniform sectors)\n");
+				break;
+	case FLASH_AM400B:	puts ("AM29LV400B (4 Mbit, bottom boot sect)\n");
+				break;
+	case FLASH_AM400T:	puts ("AM29LV400T (4 Mbit, top boot sector)\n");
+				break;
+	case FLASH_AM800B:	puts ("AM29LV800B (8 Mbit, bottom boot sect)\n");
+				break;
+	case FLASH_AM800T:	puts ("AM29LV800T (8 Mbit, top boot sector)\n");
+				break;
+	case FLASH_AM160B:	puts ("AM29LV160B (16 Mbit, bottom boot sect)\n");
+				break;
+	case FLASH_AM160T:	puts ("AM29LV160T (16 Mbit, top boot sector)\n");
+				break;
+	case FLASH_AM320B:	puts ("AM29LV320B (32 Mbit, bottom boot sect)\n");
+				break;
+	case FLASH_AM320T:	puts ("AM29LV320T (32 Mbit, top boot sector)\n");
+				break;
+	case FLASH_AM033C:	puts ("AM29LV033C (32 Mbit)\n");
+				break;
+	default:		puts ("Unknown Chip Type\n");
+				break;
+	}
+
+	printf ("  Size: %ld MB in %d Sectors\n",
+		info->size >> 20, info->sector_count);
+
+	puts ("  Sector Start Addresses:");
+
+	for (i=0; i<info->sector_count; ++i) {
+		if ((i % 5) == 0) {
+			puts ("\n   ");
+		}
+
+		printf (" %08lX%s",
+			info->start[i],
+			info->protect[i] ? " (RO)" : "     "
+		);
+	}
+
+	puts ("\n");
+}
+
+/*-----------------------------------------------------------------------
+ */
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+
+static ulong flash_get_size (vu_long *addr, flash_info_t *info)
+{
+	short i;
+#if 0
+	ulong base = (ulong)addr;
+#endif
+	uchar value;
+
+	/* Write auto select command: read Manufacturer ID */
+#if 0
+	addr[0x0555] = 0x00AA00AA;
+	addr[0x02AA] = 0x00550055;
+	addr[0x0555] = 0x00900090;
+#else
+	addr[0x0555] = 0xAAAAAAAA;
+	addr[0x02AA] = 0x55555555;
+	addr[0x0555] = 0x90909090;
+#endif
+
+	value = addr[0];
+
+	switch (value + (value << 16)) {
+	case AMD_MANUFACT:
+		info->flash_id = FLASH_MAN_AMD;
+		break;
+
+	case FUJ_MANUFACT:
+		info->flash_id = FLASH_MAN_FUJ;
+		break;
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		break;
+	}
+
+	value = addr[1];			/* device ID		*/
+
+	switch ((unsigned long)value) {
+	case AMD_ID_F040B:
+		info->flash_id += FLASH_AM040;
+		info->sector_count = 8;
+		info->size = 0x00200000;
+		break;				/* => 2 MB		*/
+
+	case AMD_ID_LV400T:
+		info->flash_id += FLASH_AM400T;
+		info->sector_count = 11;
+		info->size = 0x00100000;
+		break;				/* => 1 MB		*/
+
+	case AMD_ID_LV400B:
+		info->flash_id += FLASH_AM400B;
+		info->sector_count = 11;
+		info->size = 0x00100000;
+		break;				/* => 1 MB		*/
+
+	case AMD_ID_LV800T:
+		info->flash_id += FLASH_AM800T;
+		info->sector_count = 19;
+		info->size = 0x00200000;
+		break;				/* => 2 MB		*/
+
+	case AMD_ID_LV800B:
+		info->flash_id += FLASH_AM800B;
+		info->sector_count = 19;
+		info->size = 0x00200000;
+		break;				/* => 2 MB		*/
+
+	case AMD_ID_LV160T:
+		info->flash_id += FLASH_AM160T;
+		info->sector_count = 35;
+		info->size = 0x00400000;
+		break;				/* => 4 MB		*/
+
+	case AMD_ID_LV160B:
+		info->flash_id += FLASH_AM160B;
+		info->sector_count = 35;
+		info->size = 0x00400000;
+		break;				/* => 4 MB		*/
+#if 0	/* enable when device IDs are available */
+	case AMD_ID_LV320T:
+		info->flash_id += FLASH_AM320T;
+		info->sector_count = 67;
+		info->size = 0x00800000;
+		break;				/* => 8 MB		*/
+
+	case AMD_ID_LV320B:
+		info->flash_id += FLASH_AM320B;
+		info->sector_count = 67;
+		info->size = 0x00800000;
+		break;				/* => 8 MB		*/
+#endif
+	case AMD_ID_LV033C:
+		info->flash_id += FLASH_AM033C;
+		info->sector_count = 64;
+		info->size = 0x01000000;
+		break;				/* => 16Mb		*/
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		return (0);			/* => no or unknown flash */
+
+	}
+
+#if 0
+	/* set up sector start address table */
+	if (info->flash_id & FLASH_BTYPE) {
+		/* set sector offsets for bottom boot block type	*/
+		info->start[0] = base + 0x00000000;
+		info->start[1] = base + 0x00008000;
+		info->start[2] = base + 0x0000C000;
+		info->start[3] = base + 0x00010000;
+		for (i = 4; i < info->sector_count; i++) {
+			info->start[i] = base + (i * 0x00020000) - 0x00060000;
+		}
+	} else {
+		/* set sector offsets for top boot block type		*/
+		i = info->sector_count - 1;
+		info->start[i--] = base + info->size - 0x00008000;
+		info->start[i--] = base + info->size - 0x0000C000;
+		info->start[i--] = base + info->size - 0x00010000;
+		for (; i >= 0; i--) {
+			info->start[i] = base + i * 0x00020000;
+		}
+	}
+#else
+	flash_get_offsets ((ulong)addr, &flash_info[0]);
+#endif
+
+	/* check for protected sectors */
+	for (i = 0; i < info->sector_count; i++) {
+		/* read sector protection at sector address, (A7 .. A0) = 0x02 */
+		/* D0 = 1 if protected */
+		addr = (volatile unsigned long *)(info->start[i]);
+#if 1
+		/* We don't know why it happens, but on ICU Board	*
+		 * for AMD29033C flash we need to resend the command of	*
+		 * reading flash protection for upper 8 Mb of flash	*/
+		if ( i == 32 ) {
+			addr[0x0555] = 0xAAAAAAAA;
+			addr[0x02AA] = 0x55555555;
+			addr[0x0555] = 0x90909090;
+		}
+#endif
+		info->protect[i] = addr[2] & 1;
+	}
+
+	/*
+	 * Prevent writes to uninitialized FLASH.
+	 */
+	if (info->flash_id != FLASH_UNKNOWN) {
+		addr = (volatile unsigned long *)info->start[0];
+#if 0
+		*addr = 0x00F000F0;	/* reset bank */
+#else
+		*addr = 0xF0F0F0F0;	/* reset bank */
+#endif
+	}
+
+	return (info->size);
+}
+
+
+/*-----------------------------------------------------------------------
+ */
+
+int	flash_erase (flash_info_t *info, int s_first, int s_last)
+{
+	vu_long *addr = (vu_long*)(info->start[0]);
+	int flag, prot, sect, l_sect;
+	ulong start, now, last;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			puts ("- missing\n");
+		} else {
+			puts ("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	if ((info->flash_id == FLASH_UNKNOWN) ||
+	    (info->flash_id > FLASH_AMD_COMP)) {
+		puts ("Can't erase unknown flash type - aborted\n");
+		return 1;
+	}
+
+	prot = 0;
+	for (sect=s_first; sect<=s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+			prot);
+	} else {
+		puts ("\n");
+	}
+
+	l_sect = -1;
+
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts();
+
+#if 0
+	addr[0x0555] = 0x00AA00AA;
+	addr[0x02AA] = 0x00550055;
+	addr[0x0555] = 0x00800080;
+	addr[0x0555] = 0x00AA00AA;
+	addr[0x02AA] = 0x00550055;
+#else
+	addr[0x0555] = 0xAAAAAAAA;
+	addr[0x02AA] = 0x55555555;
+	addr[0x0555] = 0x80808080;
+	addr[0x0555] = 0xAAAAAAAA;
+	addr[0x02AA] = 0x55555555;
+#endif
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect<=s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			addr = (vu_long*)(info->start[sect]);
+#if 0
+			addr[0] = 0x00300030;
+#else
+			addr[0] = 0x30303030;
+#endif
+			l_sect = sect;
+		}
+	}
+
+	/* re-enable interrupts if necessary */
+	if (flag)
+		enable_interrupts();
+
+	/* wait at least 80us - let's wait 1 ms */
+	udelay (1000);
+
+	/*
+	 * We wait for the last triggered sector
+	 */
+	if (l_sect < 0)
+		goto DONE;
+
+	start = get_timer (0);
+	last  = start;
+	addr = (vu_long*)(info->start[l_sect]);
+#if 0
+	while ((addr[0] & 0x00800080) != 0x00800080)
+#else
+	while ((addr[0] & 0xFFFFFFFF) != 0xFFFFFFFF)
+#endif
+	{
+		if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
+			puts ("Timeout\n");
+			return 1;
+		}
+		/* show that we're waiting */
+		if ((now - last) > 1000) {	/* every second */
+			putc ('.');
+			last = now;
+		}
+	}
+
+DONE:
+	/* reset to read mode */
+	addr = (volatile unsigned long *)info->start[0];
+#if 0
+	addr[0] = 0x00F000F0;	/* reset bank */
+#else
+	addr[0] = 0xF0F0F0F0;	/* reset bank */
+#endif
+
+	puts (" done\n");
+	return 0;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+
+int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
+{
+	ulong cp, wp, data;
+	int i, l, rc;
+
+	wp = (addr & ~3);	/* get lower word aligned address */
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i=0, cp=wp; i<l; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *)cp);
+		}
+		for (; i<4 && cnt>0; ++i) {
+			data = (data << 8) | *src++;
+			--cnt;
+			++cp;
+		}
+		for (; cnt==0 && i<4; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *)cp);
+		}
+
+		if ((rc = write_word(info, wp, data)) != 0) {
+			return (rc);
+		}
+		wp += 4;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	while (cnt >= 4) {
+		data = 0;
+		for (i=0; i<4; ++i) {
+			data = (data << 8) | *src++;
+		}
+		if ((rc = write_word(info, wp, data)) != 0) {
+			return (rc);
+		}
+		wp  += 4;
+		cnt -= 4;
+	}
+
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
+		data = (data << 8) | *src++;
+		--cnt;
+	}
+	for (; i<4; ++i, ++cp) {
+		data = (data << 8) | (*(uchar *)cp);
+	}
+
+	return (write_word(info, wp, data));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_word (flash_info_t *info, ulong dest, ulong data)
+{
+	vu_long *addr = (vu_long*)(info->start[0]);
+	ulong start;
+	int flag;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*((vu_long *)dest) & data) != data) {
+		return (2);
+	}
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts();
+
+#if 0
+	addr[0x0555] = 0x00AA00AA;
+	addr[0x02AA] = 0x00550055;
+	addr[0x0555] = 0x00A000A0;
+#else
+	addr[0x0555] = 0xAAAAAAAA;
+	addr[0x02AA] = 0x55555555;
+	addr[0x0555] = 0xA0A0A0A0;
+#endif
+
+	*((vu_long *)dest) = data;
+
+	/* re-enable interrupts if necessary */
+	if (flag)
+		enable_interrupts();
+
+	/* data polling for D7 */
+	start = get_timer (0);
+#if 0
+	while ((*((vu_long *)dest) & 0x00800080) != (data & 0x00800080))
+#else
+	while ((*((vu_long *)dest) & 0x80808080) != (data & 0x80808080))
+#endif
+	{
+		if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
+			return (1);
+		}
+	}
+	return (0);
+}
+
+/*-----------------------------------------------------------------------
+ */
diff --git a/qemu/roms/u-boot/board/icu862/icu862.c b/qemu/roms/u-boot/board/icu862/icu862.c
new file mode 100644
index 000000000..4c0e91973
--- /dev/null
+++ b/qemu/roms/u-boot/board/icu862/icu862.c
@@ -0,0 +1,199 @@
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <config.h>
+#include <mpc8xx.h>
+
+/*
+ *  Memory Controller Using
+ *
+ *  CS0 - Flash memory            (0x40000000)
+ *  CS1 - SDRAM                   (0x00000000}
+ *  CS2 - S/UNI Ultra ATM155
+ *  CS3 - IDT 77106 ATM25
+ *  CS4 - DSP HPI
+ *  CS5 - E1/T1 Interface device
+ *  CS6 - PCMCIA device
+ *  CS7 - PCMCIA device
+ */
+
+/* ------------------------------------------------------------------------- */
+
+#define _not_used_	0xffffffff
+
+const uint sdram_table[] = {
+	/* single read. (offset 0 in upm RAM) */
+	0x1f07fc04, 0xeeaefc04, 0x11adfc04, 0xefbbbc00,
+	0x1ff77c47,
+
+	/* MRS initialization (offset 5) */
+
+	0x1ff77c34, 0xefeabc34, 0x1fb57c35,
+
+	/* burst read. (offset 8 in upm RAM) */
+	0x1f07fc04, 0xeeaefc04, 0x10adfc04, 0xf0affc00,
+	0xf0affc00, 0xf1affc00, 0xefbbbc00, 0x1ff77c47,
+	_not_used_, _not_used_, _not_used_, _not_used_,
+	_not_used_, _not_used_, _not_used_, _not_used_,
+
+	/* single write. (offset 18 in upm RAM) */
+	0x1f27fc04, 0xeeaebc00, 0x01b93c04, 0x1ff77c47,
+	_not_used_, _not_used_, _not_used_, _not_used_,
+
+	/* burst write. (offset 20 in upm RAM) */
+	0x1f07fc04, 0xeeaebc00, 0x10ad7c00, 0xf0affc00,
+	0xf0affc00, 0xe1bbbc04, 0x1ff77c47, _not_used_,
+	_not_used_, _not_used_, _not_used_, _not_used_,
+	_not_used_, _not_used_, _not_used_, _not_used_,
+
+	/* refresh. (offset 30 in upm RAM) */
+	0x1ff5fc84, 0xfffffc04, 0xfffffc04, 0xfffffc04,
+	0xfffffc84, 0xfffffc07, _not_used_, _not_used_,
+	_not_used_, _not_used_, _not_used_, _not_used_,
+
+	/* exception. (offset 3c in upm RAM) */
+	0x7ffffc07, _not_used_, _not_used_, _not_used_
+};
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Check Board Identity:
+ */
+
+int checkboard (void)
+{
+	puts ("Board: ICU862 Board\n");
+	return 0;
+}
+
+/* ------------------------------------------------------------------------- */
+
+static long int dram_size (long int, long int *, long int);
+
+/* ------------------------------------------------------------------------- */
+
+phys_size_t initdram (int board_type)
+{
+	volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
+	volatile memctl8xx_t *memctl = &immap->im_memctl;
+	long int size8, size9;
+	long int size_b0 = 0;
+	unsigned long reg;
+
+	upmconfig (UPMA, (uint *) sdram_table,
+			   sizeof (sdram_table) / sizeof (uint));
+
+	/*
+	 * Preliminary prescaler for refresh (depends on number of
+	 * banks): This value is selected for four cycles every 62.4 us
+	 * with two SDRAM banks or four cycles every 31.2 us with one
+	 * bank. It will be adjusted after memory sizing.
+	 */
+	memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K;
+
+	memctl->memc_mar = 0x00000088;
+
+	/*
+	 * Map controller bank 1 to the SDRAM bank at
+	 * preliminary address - these have to be modified after the
+	 * SDRAM size has been determined.
+	 */
+	memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
+	memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
+
+	memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE));	/* no refresh yet */
+
+	udelay (200);
+
+	/* perform SDRAM initializsation sequence */
+
+	memctl->memc_mcr = 0x80002105;	/* SDRAM bank 0 */
+	udelay (200);
+	memctl->memc_mcr = 0x80002230;	/* SDRAM bank 0 - execute twice */
+	udelay (200);
+
+	memctl->memc_mamr |= MAMR_PTAE;	/* enable refresh */
+
+	udelay (1000);
+
+	/*
+	 * Check Bank 0 Memory Size for re-configuration
+	 *
+	 * try 8 column mode
+	 */
+	size8 = dram_size (CONFIG_SYS_MAMR_8COL, SDRAM_BASE1_PRELIM,
+					   SDRAM_MAX_SIZE);
+
+	udelay (1000);
+
+	/*
+	 * try 9 column mode
+	 */
+	size9 = dram_size (CONFIG_SYS_MAMR_9COL, SDRAM_BASE1_PRELIM,
+					   SDRAM_MAX_SIZE);
+
+	if (size8 < size9) {		/* leave configuration at 9 columns */
+		size_b0 = size9;
+/*	debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20);	*/
+	} else {					/* back to 8 columns            */
+		size_b0 = size8;
+		memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
+		udelay (500);
+/*	debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20);	*/
+	}
+
+	udelay (1000);
+
+	/*
+	 * Adjust refresh rate depending on SDRAM type, both banks
+	 * For types > 128 MBit leave it at the current (fast) rate
+	 */
+	if ((size_b0 < 0x02000000)) {
+		/* reduce to 15.6 us (62.4 us / quad) */
+		memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
+		udelay (1000);
+	}
+
+	/*
+	 * Final mapping
+	 */
+
+	memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
+	memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
+
+	/* adjust refresh rate depending on SDRAM type, one bank */
+	reg = memctl->memc_mptpr;
+	reg >>= 1;					/* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
+	memctl->memc_mptpr = reg;
+
+	udelay (10000);
+
+	return (size_b0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Check memory range for valid RAM. A simple memory test determines
+ * the actually available RAM size between addresses `base' and
+ * `base + maxsize'. Some (not all) hardware errors are detected:
+ * - short between address lines
+ * - short between data lines
+ */
+
+static long int dram_size (long int mamr_value, long int *base,
+						   long int maxsize)
+{
+	volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
+	volatile memctl8xx_t *memctl = &immap->im_memctl;
+
+	memctl->memc_mamr = mamr_value;
+
+	return (get_ram_size(base, maxsize));
+}
diff --git a/qemu/roms/u-boot/board/icu862/pcmcia.c b/qemu/roms/u-boot/board/icu862/pcmcia.c
new file mode 100644
index 000000000..dbe3c3cf7
--- /dev/null
+++ b/qemu/roms/u-boot/board/icu862/pcmcia.c
@@ -0,0 +1,262 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if defined(CONFIG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "ICU862"
+
+static void cfg_port_B (void)
+{
+	volatile cpm8xx_t	*cp;
+	uint reg;
+
+	cp    = (cpm8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_cpm));
+
+	/*
+	 * Configure Port B for TPS2205 PC-Card Power-Interface Switch
+	 *
+	 * Switch off all voltages, assert shutdown
+	 */
+	reg  = cp->cp_pbdat;
+	reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */
+			TPS2205_VCC3    | TPS2205_VCC5    |	/* VAVCC => Hi-Z */
+			TPS2205_SHDN);				/* enable switch */
+	cp->cp_pbdat = reg;
+
+	cp->cp_pbpar &= ~(TPS2205_INPUTS | TPS2205_OUTPUTS);
+
+	reg = cp->cp_pbdir & ~(TPS2205_INPUTS);
+	cp->cp_pbdir = reg | TPS2205_OUTPUTS;
+
+	debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
+	       cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, pipr, mask;
+	int i;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_cpm));
+
+	/* Configure Port B for TPS2205 PC-Card Power-Interface Switch */
+	cfg_port_B ();
+
+	/*
+	* Configure SIUMCR to enable PCMCIA port B
+	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	*/
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
+	*/
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	pipr = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       pipr,
+	       (reg&PCMCIA_VS1(slot))?"n":"ff",
+	       (reg&PCMCIA_VS2(slot))?"n":"ff");
+
+	reg  = cp->cp_pbdat;
+	if ((pipr & mask) == mask) {
+		reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */
+				TPS2205_VCC3);				/* 3V off	*/
+		reg &= ~(TPS2205_VCC5);				/* 5V on	*/
+		puts (" 5.0V card found: ");
+	} else {
+		reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */
+				TPS2205_VCC5);				/* 5V off	*/
+		reg &= ~(TPS2205_VCC3);				/* 3V on	*/
+		puts (" 3.3V card found: ");
+	}
+
+	debug ("\nPB DAT: %08x -> 3.3V %s 5.0V %s VPP_PGM %s VPP_VCC %s\n",
+	       reg,
+	       (reg & TPS2205_VCC3)    ? "off" : "on",
+	       (reg & TPS2205_VCC5)    ? "off" : "on",
+	       (reg & TPS2205_VPP_PGM) ? "off" : "on",
+	       (reg & TPS2205_VPP_VCC) ? "off" : "on" );
+
+	cp->cp_pbdat = reg;
+
+	/*  Wait 500 ms; use this to check for over-current */
+	for (i=0; i<5000; ++i) {
+		if ((cp->cp_pbdat & TPS2205_OC) == 0) {
+			printf ("   *** Overcurrent - Safety shutdown ***\n");
+			cp->cp_pbdat &= ~(TPS2205_SHDN);
+			return (1);
+		}
+		udelay (100);
+	}
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if defined(CONFIG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CONFIG_SYS_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_cpm));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
+
+	/* Shut down */
+	cp->cp_pbdat &= ~(TPS2205_SHDN);
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(10000);
+
+	return (0);
+}
+#endif
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("voltage_set: "
+			PCMCIA_BOARD_MSG
+			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	cp    = (cpm8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_cpm));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
+	/*
+	* Disable PCMCIA buffers (isolate the interface)
+	* and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(_slot_);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Configure Port C pins for
+	* 5 Volts Enable and 3 Volts enable,
+	* Turn all power pins to Hi-Z
+	*/
+	debug ("PCMCIA power OFF\n");
+	cfg_port_B ();	/* Enables switch, but all in Hi-Z */
+
+	reg  = cp->cp_pbdat;
+
+	switch(vcc) {
+		case  0:			break;	/* Switch off		*/
+		case 33: reg &= ~TPS2205_VCC3;	break;	/* Switch on 3.3V	*/
+		case 50: reg &= ~TPS2205_VCC5;	break;	/* Switch on 5.0V	*/
+		default:			goto done;
+	}
+
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n",
+	       pcmp->pcmc_pipr,
+	       (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+	cp->cp_pbdat = reg;
+
+#ifdef DEBUG
+{
+	char *s;
+
+	if ((reg & TPS2205_VCC3) == 0) {
+		s = "at 3.3V";
+	} else if ((reg & TPS2205_VCC5) == 0) {
+		s = "at 5.0V";
+	} else {
+		s = "down";
+	}
+	printf ("PCMCIA powered %s\n", s);
+}
+#endif
+
+done:
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+	       slot+'A');
+	return (0);
+}
+
+#endif	/* CONFIG_PCMCIA */
diff --git a/qemu/roms/u-boot/board/icu862/u-boot.lds b/qemu/roms/u-boot/board/icu862/u-boot.lds
new file mode 100644
index 000000000..00f63d223
--- /dev/null
+++ b/qemu/roms/u-boot/board/icu862/u-boot.lds
@@ -0,0 +1,82 @@
+/*
+ * (C) Copyright 2001-2010
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+OUTPUT_ARCH(powerpc)
+
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .text      :
+  {
+    arch/powerpc/cpu/mpc8xx/start.o	(.text*)
+    arch/powerpc/cpu/mpc8xx/traps.o	(.text*)
+
+    *(.text*)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
+  }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    _GOT2_TABLE_ = .;
+    KEEP(*(.got2))
+    KEEP(*(.got))
+    PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
+    _FIXUP_TABLE_ = .;
+    KEEP(*(.fixup))
+  }
+  __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data*)
+    *(.sdata*)
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	KEEP(*(SORT(.u_boot_list*)));
+  }
+
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss (NOLOAD)       :
+  {
+   *(.bss*)
+   *(.sbss*)
+   *(COMMON)
+   . = ALIGN(4);
+  }
+  __bss_end = . ;
+  PROVIDE (end = .);
+}
diff --git a/qemu/roms/u-boot/board/icu862/u-boot.lds.debug b/qemu/roms/u-boot/board/icu862/u-boot.lds.debug
new file mode 100644
index 000000000..c7c6116b8
--- /dev/null
+++ b/qemu/roms/u-boot/board/icu862/u-boot.lds.debug
@@ -0,0 +1,122 @@
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+OUTPUT_ARCH(powerpc)
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text)	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data)	}
+  .rel.rodata    : { *(.rel.rodata)	}
+  .rela.rodata   : { *(.rela.rodata)	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    arch/powerpc/cpu/mpc8xx/start.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib/vsprintf.o	(.text)
+    lib/crc32.o		(.text)
+    arch/powerpc/lib/extable.o	(.text)
+
+    . = env_offset;
+    common/env_embedded.o(.text)
+
+    *(.text)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+    *(.eh_frame)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+
+  . = ALIGN(4);
+  .u_boot_list : {
+	KEEP(*(SORT(.u_boot_list*)));
+  }
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(4096);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(4096);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  __bss_end = . ;
+  PROVIDE (end = .);
+}