Adding qemu as a submodule of KVMFORNFV

This Patch includes the changes to add qemu as a submodule to
kvmfornfv repo and make use of the updated latest qemu for the
execution of all testcase
Change-Id: I1280af507a857675c7f81d30c95255635667bdd7
Signed-off-by:RajithaY<rajithax.yerrumsetty@intel.com>

2 files changed, 0 insertions, 191 deletions

diff --git a/qemu/roms/u-boot/board/galaxy5200/Makefile b/qemu/roms/u-boot/board/galaxy5200/Makefile
deleted file mode 100644
index e0fcd3951..000000000
--- a/qemu/roms/u-boot/board/galaxy5200/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2003-2007
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= galaxy5200.o
diff --git a/qemu/roms/u-boot/board/galaxy5200/galaxy5200.c b/qemu/roms/u-boot/board/galaxy5200/galaxy5200.c
deleted file mode 100644
index 29e40eb58..000000000
--- a/qemu/roms/u-boot/board/galaxy5200/galaxy5200.c
+++ /dev/null
@@ -1,183 +0,0 @@
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * (C) Copyright 2006
- * Eric Schumann, Phytec Messtechnik GmbH
- *
- * (C) Copyright 2009
- * Eric Millbrandt, DEKA Research and Development Corporation
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <pci.h>
-#include <asm/io.h>
-
-#ifndef CONFIG_SYS_RAMBOOT
-static void sdram_start(int hi_addr)
-{
-	volatile struct mpc5xxx_cdm *cdm =
-		(struct mpc5xxx_cdm *)MPC5XXX_CDM;
-	volatile struct mpc5xxx_sdram *sdram =
-		(struct mpc5xxx_sdram *)MPC5XXX_SDRAM;
-
-	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-
-	/* unlock mode register */
-	out_be32 (&sdram->ctrl,
-		(SDRAM_CONTROL | 0x80000000 | hi_addr_bit));
-
-	/* precharge all banks */
-	out_be32 (&sdram->ctrl,
-		(SDRAM_CONTROL | 0x80000002 | hi_addr_bit));
-
-#ifdef SDRAM_DDR
-	/* set mode register: extended mode */
-	out_be32 (&sdram->mode, (SDRAM_EMODE));
-
-	/* set mode register: reset DLL */
-	out_be32 (&sdram->mode, (SDRAM_MODE | 0x04000000));
-#endif
-
-	/* precharge all banks */
-	out_be32 (&sdram->ctrl,
-		(SDRAM_CONTROL | 0x80000002 | hi_addr_bit));
-
-	/* auto refresh */
-	out_be32 (&sdram->ctrl,
-		(SDRAM_CONTROL | 0x80000004 | hi_addr_bit));
-
-	/* set mode register */
-	out_be32 (&sdram->mode, (SDRAM_MODE));
-
-	/* normal operation */
-	out_be32 (&sdram->ctrl,
-		(SDRAM_CONTROL | hi_addr_bit));
-
-	/* set CDM clock enable register, set MPC5200B SDRAM bus */
-	/* to reduced driver strength */
-	out_be32 (&cdm->clock_enable, (0x00CFFFFF));
-}
-#endif
-
-/*
- * ATTENTION: Although partially referenced initdram does NOT make
- *	real use of CONFIG_SYS_SDRAM_BASE. The code does not
- *	work if CONFIG_SYS_SDRAM_BASE
- *	is something else than 0x00000000.
- */
-
-phys_size_t initdram(int board_type)
-{
-	volatile struct mpc5xxx_mmap_ctl *mm =
-		(struct mpc5xxx_mmap_ctl *)CONFIG_SYS_MBAR;
-	volatile struct mpc5xxx_sdram *sdram =
-		(struct mpc5xxx_sdram *)MPC5XXX_SDRAM;
-	ulong dramsize = 0;
-	ulong dramsize2 = 0;
-#ifndef CONFIG_SYS_RAMBOOT
-	ulong test1, test2;
-
-	/* setup SDRAM chip selects */
-							 /* 256MB at 0x0 */
-	out_be32 (&mm->sdram0, 0x0000001b);
-							 /* disabled */
-	out_be32 (&mm->sdram1, 0x10000000);
-
-	/* setup config registers */
-	out_be32 (&sdram->config1, SDRAM_CONFIG1);
-	out_be32 (&sdram->config2, SDRAM_CONFIG2);
-
-	/* find RAM size using SDRAM CS0 only */
-	sdram_start(0);
-	test1 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x10000000);
-	sdram_start(1);
-	test2 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x10000000);
-	if (test1 > test2) {
-		sdram_start(0);
-		dramsize = test1;
-	} else
-		dramsize = test2;
-
-	/* memory smaller than 1MB is impossible */
-	if (dramsize < (1 << 20))
-		dramsize = 0;
-
-	/* set SDRAM CS0 size according to the amount of RAM found */
-	if (dramsize > 0) {
-		out_be32 (&mm->sdram0,
-			(0x13 + __builtin_ffs(dramsize >> 20) - 1));
-	} else {
-							/* disabled */
-		out_be32 (&mm->sdram0, 0);
-	}
-
-#else /* CONFIG_SYS_RAMBOOT */
-
-	/* retrieve size of memory connected to SDRAM CS0 */
-	dramsize = in_be32(&mm->sdram0) & 0xFF;
-	if (dramsize >= 0x13)
-		dramsize = (1 << (dramsize - 0x13)) << 20;
-	else
-		dramsize = 0;
-
-	/* retrieve size of memory connected to SDRAM CS1 */
-	dramsize2 = in_be32(&mm->sdram1) & 0xFF;
-	if (dramsize2 >= 0x13)
-		dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
-	else
-		dramsize2 = 0;
-
-#endif /* CONFIG_SYS_RAMBOOT */
-
-	return dramsize + dramsize2;
-}
-
-int checkboard(void)
-{
-	puts("Board: galaxy5200\n");
-	return 0;
-}
-
-#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
-void ft_board_setup(void *blob, bd_t * bd)
-{
-	ft_cpu_setup(blob, bd);
-}
-#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
-
-void init_ide_reset (void)
-{
-	volatile struct mpc5xxx_gpt *gpt = (struct mpc5xxx_gpt *)MPC5XXX_GPT;
-	debug ("init_ide_reset\n");
-
-	/* Configure TIMER_5 as GPIO output for ATA reset */
-	/* Deassert reset */
-	gpt[5].emsr = MPC5XXX_GPT_GPIO_OUT1 | MPC5XXX_GPT_TMS_GPIO;
-}
-
-void ide_set_reset (int idereset)
-{
-	volatile struct mpc5xxx_gpt *gpt = (struct mpc5xxx_gpt *)MPC5XXX_GPT;
-	debug ("ide_reset(%d)\n", idereset);
-
-	/* Configure TIMER_5 as GPIO output for ATA reset */
-	if (idereset) {
-		gpt[5].emsr = MPC5XXX_GPT_GPIO_OUT0 | MPC5XXX_GPT_TMS_GPIO;
-
-		/* Make a delay. MPC5200 spec says 25 usec min */
-		udelay(50);
-	} else {
-		gpt[5].emsr = MPC5XXX_GPT_GPIO_OUT1 | MPC5XXX_GPT_TMS_GPIO;
-		udelay(50);
-	}
-}
-#endif /* defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET) */