Adding qemu as a submodule of KVMFORNFV

This Patch includes the changes to add qemu as a submodule to
kvmfornfv repo and make use of the updated latest qemu for the
execution of all testcase
Change-Id: I1280af507a857675c7f81d30c95255635667bdd7
Signed-off-by:RajithaY<rajithax.yerrumsetty@intel.com>

1 files changed, 0 insertions, 290 deletions

diff --git a/qemu/roms/u-boot/board/buffalo/lsxl/lsxl.c b/qemu/roms/u-boot/board/buffalo/lsxl/lsxl.c
deleted file mode 100644
index 659a124b2..000000000
--- a/qemu/roms/u-boot/board/buffalo/lsxl/lsxl.c
+++ /dev/null
@@ -1,290 +0,0 @@
-/*
- * Copyright (c) 2012 Michael Walle
- * Michael Walle <michael@walle.cc>
- *
- * Based on sheevaplug/sheevaplug.c by
- *   Marvell Semiconductor <www.marvell.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <net.h>
-#include <malloc.h>
-#include <netdev.h>
-#include <miiphy.h>
-#include <asm/arch/kirkwood.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/mpp.h>
-#include <asm/arch/gpio.h>
-#include <spi_flash.h>
-
-#include "lsxl.h"
-
-/*
- * Rescue mode
- *
- * Selected by holding the push button for 3 seconds, while powering on
- * the device.
- *
- * These linkstations don't have a (populated) serial port. There is no
- * way to access an (unmodified) board other than using the netconsole. If
- * you want to recover from a bad environment setting or an empty environment,
- * you can do this only with a working network connection. Therefore, a random
- * ethernet address is generated if none is set and a DHCP request is sent.
- * After a successful DHCP response is received, the network settings are
- * configured and the ncip is unset. Therefore, all netconsole packets are
- * broadcasted.
- * Additionally, the bootsource is set to 'rescue'.
- */
-
-#ifndef CONFIG_ENV_OVERWRITE
-# error "You need to set CONFIG_ENV_OVERWRITE"
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
-	/*
-	 * default gpio configuration
-	 * There are maximum 64 gpios controlled through 2 sets of registers
-	 * the below configuration configures mainly initial LED status
-	 */
-	kw_config_gpio(LSXL_OE_VAL_LOW,
-			LSXL_OE_VAL_HIGH,
-			LSXL_OE_LOW, LSXL_OE_HIGH);
-
-	/*
-	 * Multi-Purpose Pins Functionality configuration
-	 * These strappings are taken from the original vendor uboot port.
-	 */
-	static const u32 kwmpp_config[] = {
-		MPP0_SPI_SCn,
-		MPP1_SPI_MOSI,
-		MPP2_SPI_SCK,
-		MPP3_SPI_MISO,
-		MPP4_UART0_RXD,
-		MPP5_UART0_TXD,
-		MPP6_SYSRST_OUTn,
-		MPP7_GPO,
-		MPP8_GPIO,
-		MPP9_GPIO,
-		MPP10_GPO,		/* HDD power */
-		MPP11_GPIO,		/* USB Vbus enable */
-		MPP12_SD_CLK,
-		MPP13_SD_CMD,
-		MPP14_SD_D0,
-		MPP15_SD_D1,
-		MPP16_SD_D2,
-		MPP17_SD_D3,
-		MPP18_GPO,		/* fan speed high */
-		MPP19_GPO,		/* fan speed low */
-		MPP20_GE1_0,
-		MPP21_GE1_1,
-		MPP22_GE1_2,
-		MPP23_GE1_3,
-		MPP24_GE1_4,
-		MPP25_GE1_5,
-		MPP26_GE1_6,
-		MPP27_GE1_7,
-		MPP28_GPIO,
-		MPP29_GPIO,
-		MPP30_GE1_10,
-		MPP31_GE1_11,
-		MPP32_GE1_12,
-		MPP33_GE1_13,
-		MPP34_GPIO,
-		MPP35_GPIO,
-		MPP36_GPIO,		/* function LED */
-		MPP37_GPIO,		/* alarm LED */
-		MPP38_GPIO,		/* info LED */
-		MPP39_GPIO,		/* power LED */
-		MPP40_GPIO,		/* fan alarm */
-		MPP41_GPIO,		/* funtion button */
-		MPP42_GPIO,		/* power switch */
-		MPP43_GPIO,		/* power auto switch */
-		MPP44_GPIO,
-		MPP45_GPIO,
-		MPP46_GPIO,
-		MPP47_GPIO,
-		MPP48_GPIO,		/* function red LED */
-		MPP49_GPIO,
-		0
-	};
-
-	kirkwood_mpp_conf(kwmpp_config, NULL);
-
-	return 0;
-}
-
-#define LED_OFF             0
-#define LED_ALARM_ON        1
-#define LED_ALARM_BLINKING  2
-#define LED_POWER_ON        3
-#define LED_POWER_BLINKING  4
-#define LED_INFO_ON         5
-#define LED_INFO_BLINKING   6
-
-static void __set_led(int blink_alarm, int blink_info, int blink_power,
-		int value_alarm, int value_info, int value_power)
-{
-	kw_gpio_set_blink(GPIO_ALARM_LED, blink_alarm);
-	kw_gpio_set_blink(GPIO_INFO_LED, blink_info);
-	kw_gpio_set_blink(GPIO_POWER_LED, blink_power);
-	kw_gpio_set_value(GPIO_ALARM_LED, value_alarm);
-	kw_gpio_set_value(GPIO_INFO_LED, value_info);
-	kw_gpio_set_value(GPIO_POWER_LED, value_power);
-}
-
-static void set_led(int state)
-{
-	switch (state) {
-	case LED_OFF:
-		__set_led(0, 0, 0, 1, 1, 1);
-		break;
-	case LED_ALARM_ON:
-		__set_led(0, 0, 0, 0, 1, 1);
-		break;
-	case LED_ALARM_BLINKING:
-		__set_led(1, 0, 0, 1, 1, 1);
-		break;
-	case LED_INFO_ON:
-		__set_led(0, 0, 0, 1, 0, 1);
-		break;
-	case LED_INFO_BLINKING:
-		__set_led(0, 1, 0, 1, 1, 1);
-		break;
-	case LED_POWER_ON:
-		__set_led(0, 0, 0, 1, 1, 0);
-		break;
-	case LED_POWER_BLINKING:
-		__set_led(0, 0, 1, 1, 1, 1);
-		break;
-	}
-}
-
-int board_init(void)
-{
-	/* address of boot parameters */
-	gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
-
-	set_led(LED_POWER_BLINKING);
-
-	return 0;
-}
-
-#ifdef CONFIG_MISC_INIT_R
-static void check_power_switch(void)
-{
-	if (kw_gpio_get_value(GPIO_POWER_SWITCH)) {
-		/* turn off fan, HDD and USB power */
-		kw_gpio_set_value(GPIO_HDD_POWER, 0);
-		kw_gpio_set_value(GPIO_USB_VBUS, 0);
-		kw_gpio_set_value(GPIO_FAN_HIGH, 1);
-		kw_gpio_set_value(GPIO_FAN_LOW, 1);
-		set_led(LED_OFF);
-
-		/* loop until released */
-		while (kw_gpio_get_value(GPIO_POWER_SWITCH))
-			;
-
-		/* turn power on again */
-		kw_gpio_set_value(GPIO_HDD_POWER, 1);
-		kw_gpio_set_value(GPIO_USB_VBUS, 1);
-		kw_gpio_set_value(GPIO_FAN_HIGH, 0);
-		kw_gpio_set_value(GPIO_FAN_LOW, 0);
-		set_led(LED_POWER_BLINKING);
-	}
-}
-
-void check_enetaddr(void)
-{
-	uchar enetaddr[6];
-
-	if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
-		/* signal unset/invalid ethaddr to user */
-		set_led(LED_INFO_BLINKING);
-	}
-}
-
-static void erase_environment(void)
-{
-	struct spi_flash *flash;
-
-	printf("Erasing environment..\n");
-	flash = spi_flash_probe(0, 0, 1000000, SPI_MODE_3);
-	if (!flash) {
-		printf("Erasing flash failed\n");
-		return;
-	}
-
-	spi_flash_erase(flash, CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE);
-	spi_flash_free(flash);
-	do_reset(NULL, 0, 0, NULL);
-}
-
-static void rescue_mode(void)
-{
-	uchar enetaddr[6];
-
-	printf("Entering rescue mode..\n");
-#ifdef CONFIG_RANDOM_MACADDR
-	if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
-		eth_random_addr(enetaddr);
-		if (eth_setenv_enetaddr("ethaddr", enetaddr)) {
-			printf("Failed to set ethernet address\n");
-				set_led(LED_ALARM_BLINKING);
-			return;
-		}
-	}
-#endif
-	setenv("bootsource", "rescue");
-}
-
-static void check_push_button(void)
-{
-	int i = 0;
-
-	while (!kw_gpio_get_value(GPIO_FUNC_BUTTON)) {
-		udelay(100000);
-		i++;
-
-		if (i == 10)
-			set_led(LED_INFO_ON);
-
-		if (i >= 100) {
-			set_led(LED_INFO_BLINKING);
-			break;
-		}
-	}
-
-	if (i >= 100)
-		erase_environment();
-	else if (i >= 10)
-		rescue_mode();
-}
-
-int misc_init_r(void)
-{
-	check_power_switch();
-	check_enetaddr();
-	check_push_button();
-
-	return 0;
-}
-#endif
-
-#ifdef CONFIG_SHOW_BOOT_PROGRESS
-void show_boot_progress(int progress)
-{
-	if (progress > 0)
-		return;
-
-	/* this is not an error, eg. bootp with autoload=no will trigger this */
-	if (progress == -BOOTSTAGE_ID_NET_LOADED)
-		return;
-
-	set_led(LED_ALARM_BLINKING);
-}
-#endif