Adding qemu as a submodule of KVMFORNFV

This Patch includes the changes to add qemu as a submodule to
kvmfornfv repo and make use of the updated latest qemu for the
execution of all testcase
Change-Id: I1280af507a857675c7f81d30c95255635667bdd7
Signed-off-by:RajithaY<rajithax.yerrumsetty@intel.com>

4 files changed, 0 insertions, 431 deletions

diff --git a/qemu/roms/u-boot/board/amcc/yosemite/Makefile b/qemu/roms/u-boot/board/amcc/yosemite/Makefile
deleted file mode 100644
index daf020a5a..000000000
--- a/qemu/roms/u-boot/board/amcc/yosemite/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2002-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	= yosemite.o
-extra-y	+= init.o
diff --git a/qemu/roms/u-boot/board/amcc/yosemite/config.mk b/qemu/roms/u-boot/board/amcc/yosemite/config.mk
deleted file mode 100644
index f18b09710..000000000
--- a/qemu/roms/u-boot/board/amcc/yosemite/config.mk
+++ /dev/null
@@ -1,16 +0,0 @@
-#
-# (C) Copyright 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-PLATFORM_CPPFLAGS += -DCONFIG_440=1
-
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG
-endif
-
-ifeq ($(dbcr),1)
-PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000
-endif
diff --git a/qemu/roms/u-boot/board/amcc/yosemite/init.S b/qemu/roms/u-boot/board/amcc/yosemite/init.S
deleted file mode 100644
index 529cc65f7..000000000
--- a/qemu/roms/u-boot/board/amcc/yosemite/init.S
+++ /dev/null
@@ -1,49 +0,0 @@
-/*
- * SPDX-License-Identifier:	GPL-2.0+
-*/
-
-#include <asm-offsets.h>
-#include <ppc_asm.tmpl>
-#include <asm/mmu.h>
-#include <config.h>
-
-/**************************************************************************
- * TLB TABLE
- *
- * This table is used by the cpu boot code to setup the initial tlb
- * entries. Rather than make broad assumptions in the cpu source tree,
- * this table lets each board set things up however they like.
- *
- *  Pointer to the table is returned in r1
- *
- *************************************************************************/
-
-    .section .bootpg,"ax"
-    .globl tlbtab
-
-tlbtab:
-    tlbtab_start
-
-    /*
-     * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
-     * speed up boot process. It is patched after relocation to enable SA_I
-     */
-    tlbentry( CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 0, AC_RWX | SA_G/*|SA_I*/)
-
-    /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
-    tlbentry( CONFIG_SYS_INIT_RAM_ADDR, SZ_64K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G )
-
-    tlbentry( CONFIG_SYS_SDRAM_BASE, SZ_256M, CONFIG_SYS_SDRAM_BASE, 0, AC_RWX | SA_IG )
-    tlbentry( CONFIG_SYS_PCI_BASE, SZ_256M, CONFIG_SYS_PCI_BASE, 0, AC_RW | SA_IG )
-    tlbentry( CONFIG_SYS_NVRAM_BASE_ADDR, SZ_256M, CONFIG_SYS_NVRAM_BASE_ADDR, 0, AC_RWX | SA_W|SA_I )
-
-    /* PCI */
-    tlbentry( CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 0, AC_RW | SA_IG )
-    tlbentry( CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 0, AC_RW | SA_IG )
-    tlbentry( CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 0, AC_RW | SA_IG )
-    tlbentry( CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 0, AC_RW | SA_IG )
-
-    /* USB 2.0 Device */
-    tlbentry( CONFIG_SYS_USB_DEVICE, SZ_1K, 0x50000000, 0, AC_RW | SA_IG )
-
-    tlbtab_end
diff --git a/qemu/roms/u-boot/board/amcc/yosemite/yosemite.c b/qemu/roms/u-boot/board/amcc/yosemite/yosemite.c
deleted file mode 100644
index 56b5191d6..000000000
--- a/qemu/roms/u-boot/board/amcc/yosemite/yosemite.c
+++ /dev/null
@@ -1,357 +0,0 @@
-/*
- * (C) Copyright 2006-2007
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/ppc4xx.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-#include <spd_sdram.h>
-#include <libfdt.h>
-#include <fdt_support.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
-
-static inline u32 get_async_pci_freq(void)
-{
-	if (in_8((void *)(CONFIG_SYS_BCSR_BASE + 5)) &
-		CONFIG_SYS_BCSR5_PCI66EN)
-		return 66666666;
-	else
-		return 33333333;
-}
-
-int board_early_init_f(void)
-{
-	register uint reg;
-
-	/*--------------------------------------------------------------------
-	 * Setup the external bus controller/chip selects
-	 *-------------------------------------------------------------------*/
-	mtdcr(EBC0_CFGADDR, EBC0_CFG);
-	reg = mfdcr(EBC0_CFGDATA);
-	mtdcr(EBC0_CFGDATA, reg | 0x04000000);	/* Set ATC */
-
-	/*--------------------------------------------------------------------
-	 * Setup the GPIO pins
-	 *-------------------------------------------------------------------*/
-	/*CPLD cs */
-	/*setup Address lines for flash size 64Meg. */
-	out32(GPIO0_OSRL, in32(GPIO0_OSRL) | 0x50010000);
-	out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x50010000);
-	out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x50000000);
-
-	/*setup emac */
-	out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xC080);
-	out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x40);
-	out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x55);
-	out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0x50004000);
-	out32(GPIO0_ISR1H, in32(GPIO0_ISR1H) | 0x00440000);
-
-	/*UART1 */
-	out32(GPIO1_TCR, in32(GPIO1_TCR) | 0x02000000);
-	out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x00080000);
-	out32(GPIO1_ISR2L, in32(GPIO1_ISR2L) | 0x00010000);
-
-	/* external interrupts IRQ0...3 */
-	out32(GPIO1_TCR, in32(GPIO1_TCR) & ~0x00f00000);
-	out32(GPIO1_TSRL, in32(GPIO1_TSRL) & ~0x0000ff00);
-	out32(GPIO1_ISR1L, in32(GPIO1_ISR1L) | 0x00005500);
-
-#ifdef CONFIG_440EP
-	/*setup USB 2.0 */
-	out32(GPIO1_TCR, in32(GPIO1_TCR) | 0xc0000000);
-	out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x50000000);
-	out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xf);
-	out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0xaa);
-	out32(GPIO0_ISR2H, in32(GPIO0_ISR2H) | 0x00000500);
-#endif
-
-	/*--------------------------------------------------------------------
-	 * Setup the interrupt controller polarities, triggers, etc.
-	 *-------------------------------------------------------------------*/
-	mtdcr(UIC0SR, 0xffffffff);	/* clear all */
-	mtdcr(UIC0ER, 0x00000000);	/* disable all */
-	mtdcr(UIC0CR, 0x00000009);	/* ATI & UIC1 crit are critical */
-	mtdcr(UIC0PR, 0xfffffe13);	/* per ref-board manual */
-	mtdcr(UIC0TR, 0x01c00008);	/* per ref-board manual */
-	mtdcr(UIC0VR, 0x00000001);	/* int31 highest, base=0x000 */
-	mtdcr(UIC0SR, 0xffffffff);	/* clear all */
-
-	mtdcr(UIC1SR, 0xffffffff);	/* clear all */
-	mtdcr(UIC1ER, 0x00000000);	/* disable all */
-	mtdcr(UIC1CR, 0x00000000);	/* all non-critical */
-	mtdcr(UIC1PR, 0xffffe0ff);	/* per ref-board manual */
-	mtdcr(UIC1TR, 0x00ffc000);	/* per ref-board manual */
-	mtdcr(UIC1VR, 0x00000001);	/* int31 highest, base=0x000 */
-	mtdcr(UIC1SR, 0xffffffff);	/* clear all */
-
-	/*--------------------------------------------------------------------
-	 * Setup other serial configuration
-	 *-------------------------------------------------------------------*/
-	mfsdr(SDR0_PCI0, reg);
-	mtsdr(SDR0_PCI0, 0x80000000 | reg);	/* PCI arbiter enabled */
-	mtsdr(SDR0_PFC0, 0x00003e00);	/* Pin function */
-	mtsdr(SDR0_PFC1, 0x00048000);	/* Pin function: UART0 has 4 pins */
-
-	/* Check and reconfigure the PCI sync clock if necessary */
-	ppc4xx_pci_sync_clock_config(get_async_pci_freq());
-
-	/*clear tmrclk divisor */
-	*(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x04) = 0x00;
-
-	/*enable ethernet */
-	*(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x08) = 0xf0;
-
-#ifdef CONFIG_440EP
-	/*enable usb 1.1 fs device and remove usb 2.0 reset */
-	*(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x09) = 0x00;
-#endif
-
-	/*get rid of flash write protect */
-	*(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x07) = 0x00;
-
-	return 0;
-}
-
-int misc_init_r (void)
-{
-	uint pbcr;
-	int size_val = 0;
-
-	/* Re-do sizing to get full correct info */
-	mtdcr(EBC0_CFGADDR, PB0CR);
-	pbcr = mfdcr(EBC0_CFGDATA);
-	switch (gd->bd->bi_flashsize) {
-	case 1 << 20:
-		size_val = 0;
-		break;
-	case 2 << 20:
-		size_val = 1;
-		break;
-	case 4 << 20:
-		size_val = 2;
-		break;
-	case 8 << 20:
-		size_val = 3;
-		break;
-	case 16 << 20:
-		size_val = 4;
-		break;
-	case 32 << 20:
-		size_val = 5;
-		break;
-	case 64 << 20:
-		size_val = 6;
-		break;
-	case 128 << 20:
-		size_val = 7;
-		break;
-	}
-	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
-	mtdcr(EBC0_CFGADDR, PB0CR);
-	mtdcr(EBC0_CFGDATA, pbcr);
-
-	/* adjust flash start and offset */
-	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
-	gd->bd->bi_flashoffset = 0;
-
-	/* Monitor protection ON by default */
-	(void)flash_protect(FLAG_PROTECT_SET,
-			    -CONFIG_SYS_MONITOR_LEN,
-			    0xffffffff,
-			    &flash_info[0]);
-
-	return 0;
-}
-
-int checkboard(void)
-{
-	char buf[64];
-	int i = getenv_f("serial#", buf, sizeof(buf));
-	u8 rev;
-	u32 clock = get_async_pci_freq();
-
-#ifdef CONFIG_440EP
-	printf("Board: Yosemite - AMCC PPC440EP Evaluation Board");
-#else
-	printf("Board: Yellowstone - AMCC PPC440GR Evaluation Board");
-#endif
-
-	rev = in_8((void *)(CONFIG_SYS_BCSR_BASE + 0));
-	printf(", Rev. %X, PCI-Async=%d MHz", rev, clock / 1000000);
-
-	if (i > 0) {
-		puts(", serial# ");
-		puts(buf);
-	}
-	putc('\n');
-
-	/*
-	 * Reconfiguration of the PCI sync clock is already done,
-	 * now check again if everything is in range:
-	 */
-	if (ppc4xx_pci_sync_clock_config(clock)) {
-		printf("ERROR: PCI clocking incorrect (async=%d "
-		       "sync=%ld)!\n", clock, get_PCI_freq());
-	}
-
-	return (0);
-}
-
-/*************************************************************************
- *  initdram -- doesn't use serial presence detect.
- *
- *  Assumes:    256 MB, ECC, non-registered
- *              PLB @ 133 MHz
- *
- ************************************************************************/
-#define NUM_TRIES 64
-#define NUM_READS 10
-
-void sdram_tr1_set(int ram_address, int* tr1_value)
-{
-	int i;
-	int j, k;
-	volatile unsigned int* ram_pointer =  (unsigned int*)ram_address;
-	int first_good = -1, last_bad = 0x1ff;
-
-	unsigned long test[NUM_TRIES] = {
-		0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF,
-		0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF,
-		0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000,
-		0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000,
-		0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555,
-		0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555,
-		0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA,
-		0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA,
-		0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A,
-		0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A,
-		0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5,
-		0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5,
-		0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA,
-		0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA,
-		0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55,
-		0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55 };
-
-	/* go through all possible SDRAM0_TR1[RDCT] values */
-	for (i=0; i<=0x1ff; i++) {
-		/* set the current value for TR1 */
-		mtsdram(SDRAM0_TR1, (0x80800800 | i));
-
-		/* write values */
-		for (j=0; j<NUM_TRIES; j++) {
-			ram_pointer[j] = test[j];
-
-			/* clear any cache at ram location */
-			__asm__("dcbf 0,%0": :"r" (&ram_pointer[j]));
-		}
-
-		/* read values back */
-		for (j=0; j<NUM_TRIES; j++) {
-			for (k=0; k<NUM_READS; k++) {
-				/* clear any cache at ram location */
-				__asm__("dcbf 0,%0": :"r" (&ram_pointer[j]));
-
-				if (ram_pointer[j] != test[j])
-					break;
-			}
-
-			/* read error */
-			if (k != NUM_READS) {
-				break;
-			}
-		}
-
-		/* we have a SDRAM0_TR1[RDCT] that is part of the window */
-		if (j == NUM_TRIES) {
-			if (first_good == -1)
-				first_good = i;		/* found beginning of window */
-		} else { /* bad read */
-			/* if we have not had a good read then don't care */
-			if(first_good != -1) {
-				/* first failure after a good read */
-				last_bad = i-1;
-				break;
-			}
-		}
-	}
-
-	/* return the current value for TR1 */
-	*tr1_value = (first_good + last_bad) / 2;
-}
-
-phys_size_t initdram(int board)
-{
-	register uint reg;
-	int tr1_bank1, tr1_bank2;
-
-	/*--------------------------------------------------------------------
-	 * Setup some default
-	 *------------------------------------------------------------------*/
-	mtsdram(SDRAM0_UABBA, 0x00000000);	/* ubba=0 (default)             */
-	mtsdram(SDRAM0_SLIO, 0x00000000);	/* rdre=0 wrre=0 rarw=0         */
-	mtsdram(SDRAM0_DEVOPT, 0x00000000);	/* dll=0 ds=0 (normal)          */
-	mtsdram(SDRAM0_CLKTR, 0x40000000);	/* ?? */
-	mtsdram(SDRAM0_WDDCTR, 0x40000000);	/* ?? */
-
-	/*clear this first, if the DDR is enabled by a debugger
-	  then you can not make changes. */
-	mtsdram(SDRAM0_CFG0, 0x00000000);	/* Disable EEC */
-
-	/*--------------------------------------------------------------------
-	 * Setup for board-specific specific mem
-	 *------------------------------------------------------------------*/
-	/*
-	 * Following for CAS Latency = 2.5 @ 133 MHz PLB
-	 */
-	mtsdram(SDRAM0_B0CR, 0x000a4001);	/* SDBA=0x000 128MB, Mode 3, enabled */
-	mtsdram(SDRAM0_B1CR, 0x080a4001);	/* SDBA=0x080 128MB, Mode 3, enabled */
-
-	mtsdram(SDRAM0_TR0, 0x410a4012);	/* ?? */
-	mtsdram(SDRAM0_RTR, 0x04080000);	/* ?? */
-	mtsdram(SDRAM0_CFG1, 0x00000000);	/* Self-refresh exit, disable PM    */
-	mtsdram(SDRAM0_CFG0, 0x30000000);	/* Disable EEC */
-	udelay(400);		/* Delay 200 usecs (min)            */
-
-	/*--------------------------------------------------------------------
-	 * Enable the controller, then wait for DCEN to complete
-	 *------------------------------------------------------------------*/
-	mtsdram(SDRAM0_CFG0, 0x80000000);	/* Enable */
-
-	for (;;) {
-		mfsdram(SDRAM0_MCSTS, reg);
-		if (reg & 0x80000000)
-			break;
-	}
-
-	sdram_tr1_set(0x00000000, &tr1_bank1);
-	sdram_tr1_set(0x08000000, &tr1_bank2);
-	mtsdram(SDRAM0_TR1, (((tr1_bank1+tr1_bank2)/2) | 0x80800800));
-
-	return CONFIG_SYS_SDRAM_BANKS * (CONFIG_SYS_KBYTES_SDRAM * 1024);	/* return bytes */
-}
-
-/*************************************************************************
- *  hw_watchdog_reset
- *
- *	This routine is called to reset (keep alive) the watchdog timer
- *
- ************************************************************************/
-#if defined(CONFIG_HW_WATCHDOG)
-void hw_watchdog_reset(void)
-{
-
-}
-#endif
-
-void board_reset(void)
-{
-	/* give reset to BCSR */
-	*(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x06) = 0x09;
-}