diff options
author | 2016-04-11 10:41:07 +0300 | |
---|---|---|
committer | 2016-04-13 08:17:18 +0300 | |
commit | e09b41010ba33a20a87472ee821fa407a5b8da36 (patch) | |
tree | d10dc367189862e7ca5c592f033dc3726e1df4e3 /kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c | |
parent | f93b97fd65072de626c074dbe099a1fff05ce060 (diff) |
These changes are the raw update to linux-4.4.6-rt14. Kernel sources
are taken from kernel.org, and rt patch from the rt wiki download page.
During the rebasing, the following patch collided:
Force tick interrupt and get rid of softirq magic(I70131fb85).
Collisions have been removed because its logic was found on the
source already.
Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>
Diffstat (limited to 'kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c')
-rw-r--r-- | kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c | 304 |
1 files changed, 270 insertions, 34 deletions
diff --git a/kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c index 06d8f3cfa..ce61b36b9 100644 --- a/kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c +++ b/kernel/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c @@ -57,6 +57,11 @@ static s32 ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw, u16 offset); static s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw); +/* Base table for registers values that change by MAC */ +const u32 ixgbe_mvals_8259X[IXGBE_MVALS_IDX_LIMIT] = { + IXGBE_MVALS_INIT(8259X) +}; + /** * ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow * control @@ -91,6 +96,8 @@ bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw) case IXGBE_DEV_ID_82599_T3_LOM: case IXGBE_DEV_ID_X540T: case IXGBE_DEV_ID_X540T1: + case IXGBE_DEV_ID_X550T: + case IXGBE_DEV_ID_X550EM_X_10G_T: supported = true; break; default: @@ -290,13 +297,13 @@ s32 ixgbe_start_hw_generic(struct ixgbe_hw *hw) /* Setup flow control */ ret_val = ixgbe_setup_fc(hw); - if (!ret_val) - return 0; + if (ret_val) + return ret_val; /* Clear adapter stopped flag */ hw->adapter_stopped = false; - return ret_val; + return 0; } /** @@ -463,7 +470,7 @@ s32 ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw *hw) } } - if (hw->mac.type == ixgbe_mac_X540) { + if (hw->mac.type == ixgbe_mac_X550 || hw->mac.type == ixgbe_mac_X540) { if (hw->phy.id == 0) hw->phy.ops.identify(hw); hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECL, MDIO_MMD_PCS, &i); @@ -681,7 +688,7 @@ void ixgbe_set_lan_id_multi_port_pcie(struct ixgbe_hw *hw) bus->lan_id = bus->func; /* check for a port swap */ - reg = IXGBE_READ_REG(hw, IXGBE_FACTPS); + reg = IXGBE_READ_REG(hw, IXGBE_FACTPS(hw)); if (reg & IXGBE_FACTPS_LFS) bus->func ^= 0x1; } @@ -799,7 +806,7 @@ s32 ixgbe_init_eeprom_params_generic(struct ixgbe_hw *hw) * Check for EEPROM present first. * If not present leave as none */ - eec = IXGBE_READ_REG(hw, IXGBE_EEC); + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); if (eec & IXGBE_EEC_PRES) { eeprom->type = ixgbe_eeprom_spi; @@ -1283,14 +1290,14 @@ static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw) if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) != 0) return IXGBE_ERR_SWFW_SYNC; - eec = IXGBE_READ_REG(hw, IXGBE_EEC); + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); /* Request EEPROM Access */ eec |= IXGBE_EEC_REQ; - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); for (i = 0; i < IXGBE_EEPROM_GRANT_ATTEMPTS; i++) { - eec = IXGBE_READ_REG(hw, IXGBE_EEC); + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); if (eec & IXGBE_EEC_GNT) break; udelay(5); @@ -1299,7 +1306,7 @@ static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw) /* Release if grant not acquired */ if (!(eec & IXGBE_EEC_GNT)) { eec &= ~IXGBE_EEC_REQ; - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); hw_dbg(hw, "Could not acquire EEPROM grant\n"); hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); @@ -1309,7 +1316,7 @@ static s32 ixgbe_acquire_eeprom(struct ixgbe_hw *hw) /* Setup EEPROM for Read/Write */ /* Clear CS and SK */ eec &= ~(IXGBE_EEC_CS | IXGBE_EEC_SK); - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); IXGBE_WRITE_FLUSH(hw); udelay(1); return 0; @@ -1333,7 +1340,7 @@ static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw) * If the SMBI bit is 0 when we read it, then the bit will be * set and we have the semaphore */ - swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); + swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw)); if (!(swsm & IXGBE_SWSM_SMBI)) break; usleep_range(50, 100); @@ -1353,7 +1360,7 @@ static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw) * If the SMBI bit is 0 when we read it, then the bit will be * set and we have the semaphore */ - swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); + swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw)); if (swsm & IXGBE_SWSM_SMBI) { hw_dbg(hw, "Software semaphore SMBI between device drivers not granted.\n"); return IXGBE_ERR_EEPROM; @@ -1362,16 +1369,16 @@ static s32 ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw) /* Now get the semaphore between SW/FW through the SWESMBI bit */ for (i = 0; i < timeout; i++) { - swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); + swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw)); /* Set the SW EEPROM semaphore bit to request access */ swsm |= IXGBE_SWSM_SWESMBI; - IXGBE_WRITE_REG(hw, IXGBE_SWSM, swsm); + IXGBE_WRITE_REG(hw, IXGBE_SWSM(hw), swsm); /* If we set the bit successfully then we got the * semaphore. */ - swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); + swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw)); if (swsm & IXGBE_SWSM_SWESMBI) break; @@ -1400,11 +1407,11 @@ static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw) { u32 swsm; - swsm = IXGBE_READ_REG(hw, IXGBE_SWSM); + swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw)); /* Release both semaphores by writing 0 to the bits SWESMBI and SMBI */ swsm &= ~(IXGBE_SWSM_SWESMBI | IXGBE_SWSM_SMBI); - IXGBE_WRITE_REG(hw, IXGBE_SWSM, swsm); + IXGBE_WRITE_REG(hw, IXGBE_SWSM(hw), swsm); IXGBE_WRITE_FLUSH(hw); } @@ -1454,15 +1461,15 @@ static void ixgbe_standby_eeprom(struct ixgbe_hw *hw) { u32 eec; - eec = IXGBE_READ_REG(hw, IXGBE_EEC); + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); /* Toggle CS to flush commands */ eec |= IXGBE_EEC_CS; - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); IXGBE_WRITE_FLUSH(hw); udelay(1); eec &= ~IXGBE_EEC_CS; - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); IXGBE_WRITE_FLUSH(hw); udelay(1); } @@ -1480,7 +1487,7 @@ static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data, u32 mask; u32 i; - eec = IXGBE_READ_REG(hw, IXGBE_EEC); + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); /* * Mask is used to shift "count" bits of "data" out to the EEPROM @@ -1501,7 +1508,7 @@ static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data, else eec &= ~IXGBE_EEC_DI; - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); IXGBE_WRITE_FLUSH(hw); udelay(1); @@ -1518,7 +1525,7 @@ static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data, /* We leave the "DI" bit set to "0" when we leave this routine. */ eec &= ~IXGBE_EEC_DI; - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); IXGBE_WRITE_FLUSH(hw); } @@ -1539,7 +1546,7 @@ static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count) * the value of the "DO" bit. During this "shifting in" process the * "DI" bit should always be clear. */ - eec = IXGBE_READ_REG(hw, IXGBE_EEC); + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); eec &= ~(IXGBE_EEC_DO | IXGBE_EEC_DI); @@ -1547,7 +1554,7 @@ static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count) data = data << 1; ixgbe_raise_eeprom_clk(hw, &eec); - eec = IXGBE_READ_REG(hw, IXGBE_EEC); + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); eec &= ~(IXGBE_EEC_DI); if (eec & IXGBE_EEC_DO) @@ -1571,7 +1578,7 @@ static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec) * (setting the SK bit), then delay */ *eec = *eec | IXGBE_EEC_SK; - IXGBE_WRITE_REG(hw, IXGBE_EEC, *eec); + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), *eec); IXGBE_WRITE_FLUSH(hw); udelay(1); } @@ -1588,7 +1595,7 @@ static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec) * delay */ *eec = *eec & ~IXGBE_EEC_SK; - IXGBE_WRITE_REG(hw, IXGBE_EEC, *eec); + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), *eec); IXGBE_WRITE_FLUSH(hw); udelay(1); } @@ -1601,19 +1608,19 @@ static void ixgbe_release_eeprom(struct ixgbe_hw *hw) { u32 eec; - eec = IXGBE_READ_REG(hw, IXGBE_EEC); + eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw)); eec |= IXGBE_EEC_CS; /* Pull CS high */ eec &= ~IXGBE_EEC_SK; /* Lower SCK */ - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); IXGBE_WRITE_FLUSH(hw); udelay(1); /* Stop requesting EEPROM access */ eec &= ~IXGBE_EEC_REQ; - IXGBE_WRITE_REG(hw, IXGBE_EEC, eec); + IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec); hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); @@ -2157,10 +2164,11 @@ s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw) /* * In order to prevent Tx hangs when the internal Tx * switch is enabled we must set the high water mark - * to the maximum FCRTH value. This allows the Tx - * switch to function even under heavy Rx workloads. + * to the Rx packet buffer size - 24KB. This allows + * the Tx switch to function even under heavy Rx + * workloads. */ - fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 32; + fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 24576; } IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(i), fcrth); @@ -2469,6 +2477,9 @@ static s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw) hw_dbg(hw, "GIO Master Disable bit didn't clear - requesting resets\n"); hw->mac.flags |= IXGBE_FLAGS_DOUBLE_RESET_REQUIRED; + if (hw->mac.type >= ixgbe_mac_X550) + return 0; + /* * Before proceeding, make sure that the PCIe block does not have * transactions pending. @@ -3898,3 +3909,228 @@ void ixgbe_enable_rx_generic(struct ixgbe_hw *hw) } } } + +/** ixgbe_mng_present - returns true when management capability is present + * @hw: pointer to hardware structure + **/ +bool ixgbe_mng_present(struct ixgbe_hw *hw) +{ + u32 fwsm; + + if (hw->mac.type < ixgbe_mac_82599EB) + return false; + + fwsm = IXGBE_READ_REG(hw, IXGBE_FWSM(hw)); + fwsm &= IXGBE_FWSM_MODE_MASK; + return fwsm == IXGBE_FWSM_FW_MODE_PT; +} + +/** + * ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed + * @hw: pointer to hardware structure + * @speed: new link speed + * @autoneg_wait_to_complete: true when waiting for completion is needed + * + * Set the link speed in the MAC and/or PHY register and restarts link. + */ +s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, + ixgbe_link_speed speed, + bool autoneg_wait_to_complete) +{ + ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN; + ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN; + s32 status = 0; + u32 speedcnt = 0; + u32 i = 0; + bool autoneg, link_up = false; + + /* Mask off requested but non-supported speeds */ + status = hw->mac.ops.get_link_capabilities(hw, &link_speed, &autoneg); + if (status) + return status; + + speed &= link_speed; + + /* Try each speed one by one, highest priority first. We do this in + * software because 10Gb fiber doesn't support speed autonegotiation. + */ + if (speed & IXGBE_LINK_SPEED_10GB_FULL) { + speedcnt++; + highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL; + + /* If we already have link at this speed, just jump out */ + status = hw->mac.ops.check_link(hw, &link_speed, &link_up, + false); + if (status) + return status; + + if (link_speed == IXGBE_LINK_SPEED_10GB_FULL && link_up) + goto out; + + /* Set the module link speed */ + switch (hw->phy.media_type) { + case ixgbe_media_type_fiber: + hw->mac.ops.set_rate_select_speed(hw, + IXGBE_LINK_SPEED_10GB_FULL); + break; + case ixgbe_media_type_fiber_qsfp: + /* QSFP module automatically detects MAC link speed */ + break; + default: + hw_dbg(hw, "Unexpected media type\n"); + break; + } + + /* Allow module to change analog characteristics (1G->10G) */ + msleep(40); + + status = hw->mac.ops.setup_mac_link(hw, + IXGBE_LINK_SPEED_10GB_FULL, + autoneg_wait_to_complete); + if (status) + return status; + + /* Flap the Tx laser if it has not already been done */ + if (hw->mac.ops.flap_tx_laser) + hw->mac.ops.flap_tx_laser(hw); + + /* Wait for the controller to acquire link. Per IEEE 802.3ap, + * Section 73.10.2, we may have to wait up to 500ms if KR is + * attempted. 82599 uses the same timing for 10g SFI. + */ + for (i = 0; i < 5; i++) { + /* Wait for the link partner to also set speed */ + msleep(100); + + /* If we have link, just jump out */ + status = hw->mac.ops.check_link(hw, &link_speed, + &link_up, false); + if (status) + return status; + + if (link_up) + goto out; + } + } + + if (speed & IXGBE_LINK_SPEED_1GB_FULL) { + speedcnt++; + if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN) + highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL; + + /* If we already have link at this speed, just jump out */ + status = hw->mac.ops.check_link(hw, &link_speed, &link_up, + false); + if (status) + return status; + + if (link_speed == IXGBE_LINK_SPEED_1GB_FULL && link_up) + goto out; + + /* Set the module link speed */ + switch (hw->phy.media_type) { + case ixgbe_media_type_fiber: + hw->mac.ops.set_rate_select_speed(hw, + IXGBE_LINK_SPEED_1GB_FULL); + break; + case ixgbe_media_type_fiber_qsfp: + /* QSFP module automatically detects link speed */ + break; + default: + hw_dbg(hw, "Unexpected media type\n"); + break; + } + + /* Allow module to change analog characteristics (10G->1G) */ + msleep(40); + + status = hw->mac.ops.setup_mac_link(hw, + IXGBE_LINK_SPEED_1GB_FULL, + autoneg_wait_to_complete); + if (status) + return status; + + /* Flap the Tx laser if it has not already been done */ + if (hw->mac.ops.flap_tx_laser) + hw->mac.ops.flap_tx_laser(hw); + + /* Wait for the link partner to also set speed */ + msleep(100); + + /* If we have link, just jump out */ + status = hw->mac.ops.check_link(hw, &link_speed, &link_up, + false); + if (status) + return status; + + if (link_up) + goto out; + } + + /* We didn't get link. Configure back to the highest speed we tried, + * (if there was more than one). We call ourselves back with just the + * single highest speed that the user requested. + */ + if (speedcnt > 1) + status = ixgbe_setup_mac_link_multispeed_fiber(hw, + highest_link_speed, + autoneg_wait_to_complete); + +out: + /* Set autoneg_advertised value based on input link speed */ + hw->phy.autoneg_advertised = 0; + + if (speed & IXGBE_LINK_SPEED_10GB_FULL) + hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL; + + if (speed & IXGBE_LINK_SPEED_1GB_FULL) + hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL; + + return status; +} + +/** + * ixgbe_set_soft_rate_select_speed - Set module link speed + * @hw: pointer to hardware structure + * @speed: link speed to set + * + * Set module link speed via the soft rate select. + */ +void ixgbe_set_soft_rate_select_speed(struct ixgbe_hw *hw, + ixgbe_link_speed speed) +{ + s32 status; + u8 rs, eeprom_data; + + switch (speed) { + case IXGBE_LINK_SPEED_10GB_FULL: + /* one bit mask same as setting on */ + rs = IXGBE_SFF_SOFT_RS_SELECT_10G; + break; + case IXGBE_LINK_SPEED_1GB_FULL: + rs = IXGBE_SFF_SOFT_RS_SELECT_1G; + break; + default: + hw_dbg(hw, "Invalid fixed module speed\n"); + return; + } + + /* Set RS0 */ + status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB, + IXGBE_I2C_EEPROM_DEV_ADDR2, + &eeprom_data); + if (status) { + hw_dbg(hw, "Failed to read Rx Rate Select RS0\n"); + return; + } + + eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs; + + status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB, + IXGBE_I2C_EEPROM_DEV_ADDR2, + eeprom_data); + if (status) { + hw_dbg(hw, "Failed to write Rx Rate Select RS0\n"); + return; + } +} |