These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

39 files changed, 1096 insertions, 21 deletions

diff --git a/kernel/Documentation/devicetree/bindings/sound/adi,adau1701.txt b/kernel/Documentation/devicetree/bindings/sound/adi,adau1701.txt
index 547a49b56..0d1128ce2 100644
--- a/kernel/Documentation/devicetree/bindings/sound/adi,adau1701.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/adi,adau1701.txt
@@ -20,6 +20,8 @@ Optional properties:
 			pin configurations as described in the datasheet,
 			table 53. Note that the value of this property has
 			to be prefixed with '/bits/ 8'.
+ - avdd-supply: 	Power supply for AVDD, providing 3.3V
+ - dvdd-supply: 	Power supply for DVDD, providing 3.3V
 
 Examples:
 
@@ -28,6 +30,8 @@ Examples:
 			compatible = "adi,adau1701";
 			reg = <0x34>;
 			reset-gpio = <&gpio 23 0>;
+			avdd-supply = <&vdd_3v3_reg>;
+			dvdd-supply = <&vdd_3v3_reg>;
 			adi,pll-mode-gpios = <&gpio 24 0 &gpio 25 0>;
 			adi,pin-config = /bits/ 8 <0x4 0x7 0x5 0x5 0x4 0x4
                                                    0x4 0x4 0x4 0x4 0x4 0x4>;
diff --git a/kernel/Documentation/devicetree/bindings/sound/ak4554.c b/kernel/Documentation/devicetree/bindings/sound/ak4554.txt
index 934fa0275..934fa0275 100644
--- a/kernel/Documentation/devicetree/bindings/sound/ak4554.c
+++ b/kernel/Documentation/devicetree/bindings/sound/ak4554.txt
diff --git a/kernel/Documentation/devicetree/bindings/sound/ak4613.txt b/kernel/Documentation/devicetree/bindings/sound/ak4613.txt
new file mode 100644
index 000000000..15a919522
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/ak4613.txt
@@ -0,0 +1,17 @@
+AK4613 I2C transmitter
+
+This device supports I2C mode only.
+
+Required properties:
+
+- compatible : "asahi-kasei,ak4613"
+- reg : The chip select number on the I2C bus
+
+Example:
+
+&i2c {
+	ak4613: ak4613@0x10 {
+		compatible = "asahi-kasei,ak4613";
+		reg = <0x10>;
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/ak4642.txt b/kernel/Documentation/devicetree/bindings/sound/ak4642.txt
index 623d4e70a..340784db6 100644
--- a/kernel/Documentation/devicetree/bindings/sound/ak4642.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/ak4642.txt
@@ -7,7 +7,14 @@ Required properties:
   - compatible : "asahi-kasei,ak4642" or "asahi-kasei,ak4643" or "asahi-kasei,ak4648"
   - reg : The chip select number on the I2C bus
 
-Example:
+Optional properties:
+
+  - #clock-cells :		common clock binding; shall be set to 0
+  - clocks :			common clock binding; MCKI clock
+  - clock-frequency :		common clock binding; frequency of MCKO
+  - clock-output-names :	common clock binding; MCKO clock name
+
+Example 1:
 
 &i2c {
 	ak4648: ak4648@0x12 {
@@ -15,3 +22,16 @@ Example:
 		reg = <0x12>;
 	};
 };
+
+Example 2:
+
+&i2c {
+	ak4643: codec@12 {
+		compatible = "asahi-kasei,ak4643";
+		reg = <0x12>;
+		#clock-cells = <0>;
+		clocks = <&audio_clock>;
+		clock-frequency = <12288000>;
+		clock-output-names = "ak4643_mcko";
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/atmel-classd.txt b/kernel/Documentation/devicetree/bindings/sound/atmel-classd.txt
new file mode 100644
index 000000000..0018451c4
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/atmel-classd.txt
@@ -0,0 +1,52 @@
+* Atmel ClassD driver under ALSA SoC architecture
+
+Required properties:
+- compatible
+	Should be "atmel,sama5d2-classd".
+- reg
+	Should contain ClassD registers location and length.
+- interrupts
+	Should contain the IRQ line for the ClassD.
+- dmas
+	One DMA specifiers as described in atmel-dma.txt and dma.txt files.
+- dma-names
+	Must be "tx".
+- clock-names
+	Tuple listing input clock names.
+	Required elements: "pclk", "gclk" and "aclk".
+- clocks
+	Please refer to clock-bindings.txt.
+
+Optional properties:
+- pinctrl-names, pinctrl-0
+	Please refer to pinctrl-bindings.txt.
+- atmel,model
+	The user-visible name of this sound complex.
+	The default value is "CLASSD".
+- atmel,pwm-type
+	PWM modulation type, "single" or "diff".
+	The default value is "single".
+- atmel,non-overlap-time
+	Set non-overlapping time, the unit is nanosecond(ns).
+	There are four values,
+	<5>, <10>, <15>, <20>, the default value is <10>.
+	Non-overlapping will be disabled if not specified.
+
+Example:
+classd: classd@fc048000 {
+		compatible = "atmel,sama5d2-classd";
+		reg = <0xfc048000 0x100>;
+		interrupts = <59 IRQ_TYPE_LEVEL_HIGH 7>;
+		dmas = <&dma0
+			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+			| AT91_XDMAC_DT_PERID(47))>;
+		dma-names = "tx";
+		clocks = <&classd_clk>, <&classd_gclk>, <&audio_pll_pmc>;
+		clock-names = "pclk", "gclk", "aclk";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_classd_default>;
+		atmel,model = "classd @ SAMA5D2-Xplained";
+		atmel,pwm-type = "diff";
+		atmel,non-overlap-time = <10>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/bt-sco.txt b/kernel/Documentation/devicetree/bindings/sound/bt-sco.txt
new file mode 100644
index 000000000..29b8e5d40
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/bt-sco.txt
@@ -0,0 +1,13 @@
+Bluetooth-SCO audio CODEC
+
+This device support generic Bluetooth SCO link.
+
+Required properties:
+
+  - compatible : "delta,dfbmcs320"
+
+Example:
+
+codec: bt_sco {
+	compatible = "delta,dfbmcs320";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/cs4349.txt b/kernel/Documentation/devicetree/bindings/sound/cs4349.txt
new file mode 100644
index 000000000..54c117b59
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/cs4349.txt
@@ -0,0 +1,19 @@
+CS4349 audio CODEC
+
+Required properties:
+
+  - compatible : "cirrus,cs4349"
+
+  - reg : the I2C address of the device for I2C
+
+Optional properties:
+
+  - reset-gpios : a GPIO spec for the reset pin.
+
+Example:
+
+codec: cs4349@48 {
+        compatible = "cirrus,cs4349";
+        reg = <0x48>;
+        reset-gpios = <&gpio 54 0>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/da7213.txt b/kernel/Documentation/devicetree/bindings/sound/da7213.txt
new file mode 100644
index 000000000..58902802d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/da7213.txt
@@ -0,0 +1,41 @@
+Dialog Semiconductor DA7213 Audio Codec bindings
+
+======
+
+Required properties:
+- compatible : Should be "dlg,da7213"
+- reg: Specifies the I2C slave address
+
+Optional properties:
+- clocks : phandle and clock specifier for codec MCLK.
+- clock-names : Clock name string for 'clocks' attribute, should be "mclk".
+
+- dlg,micbias1-lvl : Voltage (mV) for Mic Bias 1
+	[<1600>, <2200>, <2500>, <3000>]
+- dlg,micbias2-lvl : Voltage (mV) for Mic Bias 2
+	[<1600>, <2200>, <2500>, <3000>]
+- dlg,dmic-data-sel : DMIC channel select based on clock edge.
+	["lrise_rfall", "lfall_rrise"]
+- dlg,dmic-samplephase : When to sample audio from DMIC.
+	["on_clkedge", "between_clkedge"]
+- dlg,dmic-clkrate : DMIC clock frequency (Hz).
+	[<1500000>, <3000000>]
+
+======
+
+Example:
+
+	codec_i2c: da7213@1a {
+		compatible = "dlg,da7213";
+ 		reg = <0x1a>;
+
+ 		clocks = <&clks 201>;
+		clock-names = "mclk";
+
+		dlg,micbias1-lvl = <2500>;
+		dlg,micbias2-lvl = <2500>;
+
+		dlg,dmic-data-sel = "lrise_rfall";
+		dlg,dmic-samplephase = "between_clkedge";
+		dlg,dmic-clkrate = <3000000>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/da7219.txt b/kernel/Documentation/devicetree/bindings/sound/da7219.txt
new file mode 100644
index 000000000..1b7030911
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/da7219.txt
@@ -0,0 +1,106 @@
+Dialog Semiconductor DA7219 Audio Codec bindings
+
+DA7219 is an audio codec with advanced accessory detect features.
+
+======
+
+Required properties:
+- compatible : Should be "dlg,da7219"
+- reg: Specifies the I2C slave address
+
+- interrupt-parent : Specifies the phandle of the interrupt controller to which
+  the IRQs from DA7219 are delivered to.
+- interrupts : IRQ line info for DA7219.
+  (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for
+   further information relating to interrupt properties)
+
+- VDD-supply: VDD power supply for the device
+- VDDMIC-supply: VDDMIC power supply for the device
+- VDDIO-supply: VDDIO power supply for the device
+  (See Documentation/devicetree/bindings/regulator/regulator.txt for further
+   information relating to regulators)
+
+Optional properties:
+- interrupt-names : Name associated with interrupt line. Should be "wakeup" if
+  interrupt is to be used to wake system, otherwise "irq" should be used.
+- wakeup-source: Flag to indicate this device can wake system (suspend/resume).
+
+- clocks : phandle and clock specifier for codec MCLK.
+- clock-names : Clock name string for 'clocks' attribute, should be "mclk".
+
+- dlg,ldo-lvl : Required internal LDO voltage (mV) level for digital engine
+	[<1050>, <1100>, <1200>, <1400>]
+- dlg,micbias-lvl : Voltage (mV) for Mic Bias
+	[<1800>, <2000>, <2200>, <2400>, <2600>]
+- dlg,mic-amp-in-sel : Mic input source type
+	["diff", "se_p", "se_n"]
+
+======
+
+Child node - 'da7219_aad':
+
+Optional properties:
+- dlg,micbias-pulse-lvl : Mic bias higher voltage pulse level (mV).
+	[<2800>, <2900>]
+- dlg,micbias-pulse-time : Mic bias higher voltage pulse duration (ms)
+- dlg,btn-cfg : Periodic button press measurements for 4-pole jack (ms)
+	[<2>, <5>, <10>, <50>, <100>, <200>, <500>]
+- dlg,mic-det-thr : Impedance threshold for mic detection measurement (Ohms)
+	[<200>, <500>, <750>, <1000>]
+- dlg,jack-ins-deb : Debounce time for jack insertion (ms)
+	[<5>, <10>, <20>, <50>, <100>, <200>, <500>, <1000>]
+- dlg,jack-det-rate: Jack type detection latency (3/4 pole)
+	["32ms_64ms", "64ms_128ms", "128ms_256ms", "256ms_512ms"]
+- dlg,jack-rem-deb : Debounce time for jack removal (ms)
+	[<1>, <5>, <10>, <20>]
+- dlg,a-d-btn-thr : Impedance threshold between buttons A and D
+	[0x0 - 0xFF]
+- dlg,d-b-btn-thr : Impedance threshold between buttons D and B
+	[0x0 - 0xFF]
+- dlg,b-c-btn-thr : Impedance threshold between buttons B and C
+	[0x0 - 0xFF]
+- dlg,c-mic-btn-thr : Impedance threshold between button C and Mic
+	[0x0 - 0xFF]
+- dlg,btn-avg : Number of 8-bit readings for averaged button measurement
+	[<1>, <2>, <4>, <8>]
+- dlg,adc-1bit-rpt : Repeat count for 1-bit button measurement
+	[<1>, <2>, <4>, <8>]
+
+======
+
+Example:
+
+	codec: da7219@1a {
+		compatible = "dlg,da7219";
+		reg = <0x1a>;
+
+		interrupt-parent = <&gpio6>;
+		interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+
+		VDD-supply = <&reg_audio>;
+		VDDMIC-supply = <&reg_audio>;
+		VDDIO-supply = <&reg_audio>;
+
+		clocks = <&clks 201>;
+		clock-names = "mclk";
+
+		dlg,ldo-lvl = <1200>;
+		dlg,micbias-lvl = <2600>;
+		dlg,mic-amp-in-sel = "diff";
+
+		da7219_aad {
+			dlg,btn-cfg = <50>;
+			dlg,mic-det-thr = <500>;
+			dlg,jack-ins-deb = <20>;
+			dlg,jack-det-rate = "32ms_64ms";
+			dlg,jack-rem-deb = <1>;
+
+			dlg,a-d-btn-thr = <0xa>;
+			dlg,d-b-btn-thr = <0x16>;
+			dlg,b-c-btn-thr = <0x21>;
+			dlg,c-mic-btn-thr = <0x3E>;
+
+			dlg,btn-avg = <4>;
+			dlg,adc-1bit-rpt = <1>;
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt b/kernel/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt
index a96774c19..ce55c0a6f 100644
--- a/kernel/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt
@@ -13,13 +13,15 @@ So having this generic sound card allows all Freescale SoC users to benefit
 from the simplification of a new card support and the capability of the wide
 sample rates support through ASRC.
 
-Note: The card is initially designed for those sound cards who use I2S and
-      PCM DAI formats. However, it'll be also possible to support those non
-      I2S/PCM type sound cards, such as S/PDIF audio and HDMI audio, as long
-      as the driver has been properly upgraded.
+Note: The card is initially designed for those sound cards who use AC'97, I2S
+      and PCM DAI formats. However, it'll be also possible to support those non
+      AC'97/I2S/PCM type sound cards, such as S/PDIF audio and HDMI audio, as
+      long as the driver has been properly upgraded.
 
 
 The compatible list for this generic sound card currently:
+ "fsl,imx-audio-ac97"
+
  "fsl,imx-audio-cs42888"
 
  "fsl,imx-audio-wm8962"
diff --git a/kernel/Documentation/devicetree/bindings/sound/gtm601.txt b/kernel/Documentation/devicetree/bindings/sound/gtm601.txt
new file mode 100644
index 000000000..5efc8c068
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/gtm601.txt
@@ -0,0 +1,13 @@
+GTM601 UMTS modem audio interface CODEC
+
+This device has no configuration interface. Sample rate is fixed - 8kHz.
+
+Required properties:
+
+  - compatible : "option,gtm601"
+
+Example:
+
+codec: gtm601_codec {
+	compatible = "option,gtm601";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/ics43432.txt b/kernel/Documentation/devicetree/bindings/sound/ics43432.txt
new file mode 100644
index 000000000..b02e3a6c0
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/ics43432.txt
@@ -0,0 +1,17 @@
+Invensense ICS-43432 MEMS microphone with I2S output.
+
+There are no software configuration options for this device, indeed, the only
+host connection is the I2S interface. Apart from requirements on clock
+frequency (460 kHz to 3.379 MHz according to the data sheet) there must be
+64 clock cycles in each stereo output frame; 24 of the 32 available bits
+contain audio data. A hardware pin determines if the device outputs data
+on the left or right channel of the I2S frame.
+
+Required properties:
+  - compatible : Must be "invensense,ics43432"
+
+Example:
+
+	ics43432: ics43432 {
+		compatible = "invensense,ics43432";
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/max98090.txt b/kernel/Documentation/devicetree/bindings/sound/max98090.txt
index aa802a274..4e3be6682 100644
--- a/kernel/Documentation/devicetree/bindings/sound/max98090.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/max98090.txt
@@ -18,6 +18,12 @@ Optional properties:
 
 - maxim,dmic-freq: Frequency at which to clock DMIC
 
+- maxim,micbias: Micbias voltage applies to the analog mic, valid voltages value are:
+	0 - 2.2v
+	1 - 2.55v
+	2 - 2.4v
+	3 - 2.8v
+
 Pins on the device (for linking into audio routes):
 
   * MIC1
diff --git a/kernel/Documentation/devicetree/bindings/sound/max98357a.txt b/kernel/Documentation/devicetree/bindings/sound/max98357a.txt
index a7a149a23..28645a2ff 100644
--- a/kernel/Documentation/devicetree/bindings/sound/max98357a.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/max98357a.txt
@@ -4,7 +4,11 @@ This node models the Maxim MAX98357A DAC.
 
 Required properties:
 - compatible   : "maxim,max98357a"
-- sdmode-gpios : GPIO specifier for the GPIO -> DAC SDMODE pin
+
+Optional properties:
+- sdmode-gpios : GPIO specifier for the chip's SD_MODE pin.
+        If this option is not specified then driver does not manage
+        the pin state (e.g. chip is always on).
 
 Example:
 
diff --git a/kernel/Documentation/devicetree/bindings/sound/mt8173-max98090.txt b/kernel/Documentation/devicetree/bindings/sound/mt8173-max98090.txt
new file mode 100644
index 000000000..519e97c8f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/mt8173-max98090.txt
@@ -0,0 +1,15 @@
+MT8173 with MAX98090 CODEC
+
+Required properties:
+- compatible : "mediatek,mt8173-max98090"
+- mediatek,audio-codec: the phandle of the MAX98090 audio codec
+- mediatek,platform: the phandle of MT8173 ASoC platform
+
+Example:
+
+	sound {
+		compatible = "mediatek,mt8173-max98090";
+		mediatek,audio-codec = <&max98090>;
+		mediatek,platform = <&afe>;
+	};
+
diff --git a/kernel/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt b/kernel/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt
new file mode 100644
index 000000000..f205ce9e3
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt
@@ -0,0 +1,15 @@
+MT8173 with RT5650 RT5676 CODECS
+
+Required properties:
+- compatible : "mediatek,mt8173-rt5650-rt5676"
+- mediatek,audio-codec: the phandles of rt5650 and rt5676 codecs
+- mediatek,platform: the phandle of MT8173 ASoC platform
+
+Example:
+
+	sound {
+		compatible = "mediatek,mt8173-rt5650-rt5676";
+		mediatek,audio-codec = <&rt5650 &rt5676>;
+		mediatek,platform = <&afe>;
+	};
+
diff --git a/kernel/Documentation/devicetree/bindings/sound/mtk-afe-pcm.txt b/kernel/Documentation/devicetree/bindings/sound/mtk-afe-pcm.txt
new file mode 100644
index 000000000..e302c7f43
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/mtk-afe-pcm.txt
@@ -0,0 +1,45 @@
+Mediatek AFE PCM controller
+
+Required properties:
+- compatible = "mediatek,mt8173-afe-pcm";
+- reg: register location and size
+- interrupts: Should contain AFE interrupt
+- clock-names: should have these clock names:
+		"infra_sys_audio_clk",
+		"top_pdn_audio",
+		"top_pdn_aud_intbus",
+		"bck0",
+		"bck1",
+		"i2s0_m",
+		"i2s1_m",
+		"i2s2_m",
+		"i2s3_m",
+		"i2s3_b";
+
+Example:
+
+	afe: mt8173-afe-pcm@11220000  {
+		compatible = "mediatek,mt8173-afe-pcm";
+		reg = <0 0x11220000 0 0x1000>;
+		interrupts = <GIC_SPI 134 IRQ_TYPE_EDGE_FALLING>;
+		clocks = <&infracfg INFRA_AUDIO>,
+			<&topckgen TOP_AUDIO_SEL>,
+			<&topckgen TOP_AUD_INTBUS_SEL>,
+			<&topckgen TOP_APLL1_DIV0>,
+			<&topckgen TOP_APLL2_DIV0>,
+			<&topckgen TOP_I2S0_M_CK_SEL>,
+			<&topckgen TOP_I2S1_M_CK_SEL>,
+			<&topckgen TOP_I2S2_M_CK_SEL>,
+			<&topckgen TOP_I2S3_M_CK_SEL>,
+			<&topckgen TOP_I2S3_B_CK_SEL>;
+		clock-names = "infra_sys_audio_clk",
+				"top_pdn_audio",
+				"top_pdn_aud_intbus",
+				"bck0",
+				"bck1",
+				"i2s0_m",
+				"i2s1_m",
+				"i2s2_m",
+				"i2s3_m",
+				"i2s3_b";
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/nau8825.txt b/kernel/Documentation/devicetree/bindings/sound/nau8825.txt
new file mode 100644
index 000000000..d3374231c
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nau8825.txt
@@ -0,0 +1,102 @@
+Nuvoton NAU8825 audio codec
+
+This device supports I2C only.
+
+Required properties:
+  - compatible : Must be "nuvoton,nau8825"
+
+  - reg : the I2C address of the device. This is either 0x1a (CSB=0) or 0x1b (CSB=1).
+
+Optional properties:
+  - nuvoton,jkdet-enable: Enable jack detection via JKDET pin.
+  - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled,
+      otherwise pin in high impedance state.
+  - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down.
+  - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low.
+
+  - nuvoton,vref-impedance: VREF Impedance selection
+      0 - Open
+      1 - 25 kOhm
+      2 - 125 kOhm
+      3 - 2.5 kOhm
+
+  - nuvoton,micbias-voltage: Micbias voltage level.
+      0 - VDDA
+      1 - VDDA
+      2 - VDDA * 1.1
+      3 - VDDA * 1.2
+      4 - VDDA * 1.3
+      5 - VDDA * 1.4
+      6 - VDDA * 1.53
+      7 - VDDA * 1.53
+
+  - nuvoton,sar-threshold-num: Number of buttons supported
+  - nuvoton,sar-threshold: Impedance threshold for each button. Array that contains up to 8 buttons configuration. SAR value is calculated as
+    SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R)
+    where MICBIAS is configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by 'nuvoton,sar-voltage', R - button impedance.
+    Refer datasheet section 10.2 for more information about threshold calculation.
+
+  - nuvoton,sar-hysteresis: Button impedance measurement hysteresis.
+
+  - nuvoton,sar-voltage: Reference voltage for button impedance measurement.
+      0 - VDDA
+      1 - VDDA
+      2 - VDDA * 1.1
+      3 - VDDA * 1.2
+      4 - VDDA * 1.3
+      5 - VDDA * 1.4
+      6 - VDDA * 1.53
+      7 - VDDA * 1.53
+
+  - nuvoton,sar-compare-time: SAR compare time
+      0 - 500 ns
+      1 - 1 us
+      2 - 2 us
+      3 - 4 us
+
+  - nuvoton,sar-sampling-time: SAR sampling time
+      0 - 2 us
+      1 - 4 us
+      2 - 8 us
+      3 - 16 us
+
+  - nuvoton,short-key-debounce: Button short key press debounce time.
+      0 - 30 ms
+      1 - 50 ms
+      2 - 100 ms
+      3 - 30 ms
+
+  - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
+  - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
+
+  - clocks: list of phandle and clock specifier pairs according to common clock bindings for the
+      clocks described in clock-names
+  - clock-names: should include "mclk" for the MCLK master clock
+
+Example:
+
+  headset: nau8825@1a {
+      compatible = "nuvoton,nau8825";
+      reg = <0x1a>;
+      interrupt-parent = <&gpio>;
+      interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>;
+      nuvoton,jkdet-enable;
+      nuvoton,jkdet-pull-enable;
+      nuvoton,jkdet-pull-up;
+      nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>;
+      nuvoton,vref-impedance = <2>;
+      nuvoton,micbias-voltage = <6>;
+      // Setup 4 buttons impedance according to Android specification
+      nuvoton,sar-threshold-num = <4>;
+      nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>;
+      nuvoton,sar-hysteresis = <1>;
+      nuvoton,sar-voltage = <0>;
+      nuvoton,sar-compare-time = <0>;
+      nuvoton,sar-sampling-time = <0>;
+      nuvoton,short-key-debounce = <2>;
+      nuvoton,jack-insert-debounce = <7>;
+      nuvoton,jack-eject-debounce = <7>;
+
+      clock-names = "mclk";
+      clocks = <&tegra_car TEGRA210_CLK_CLK_OUT_2>;
+  };
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt
index 13e2ef496..275c6ea35 100644
--- a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt
@@ -8,10 +8,10 @@ Required properties:
 - interrupts : The interrupt from the HDA controller.
 - clocks : Must contain an entry for each required entry in clock-names.
   See ../clocks/clock-bindings.txt for details.
-- clock-names : Must include the following entries: hda, hdacodec_2x, hda2hdmi
+- clock-names : Must include the following entries: hda, hda2hdmi, hda2codec_2x
 - resets : Must contain an entry for each entry in reset-names.
   See ../reset/reset.txt for details.
-- reset-names : Must include the following entries: hda, hdacodec_2x, hda2hdmi
+- reset-names : Must include the following entries: hda, hda2hdmi, hda2codec_2x
 
 Example:
 
@@ -24,7 +24,7 @@ hda@0,70030000 {
 		 <&tegra_car TEGRA124_CLK_HDA2CODEC_2X>;
 	clock-names = "hda", "hda2hdmi", "hda2codec_2x";
 	resets = <&tegra_car 125>, /* hda */
-		 <&tegra_car 128>; /* hda2hdmi */
-		 <&tegra_car 111>, /* hda2codec_2x */
+		 <&tegra_car 128>, /* hda2hdmi */
+		 <&tegra_car 111>; /* hda2codec_2x */
 	reset-names = "hda", "hda2hdmi", "hda2codec_2x";
 };
diff --git a/kernel/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt b/kernel/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt
new file mode 100644
index 000000000..48129368d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt
@@ -0,0 +1,60 @@
+* Qualcomm Technologies APQ8016 SBC ASoC machine driver
+
+This node models the Qualcomm Technologies APQ8016 SBC ASoC machine driver
+
+Required properties:
+
+- compatible		: "qcom,apq8016-sbc-sndcard"
+
+- pinctrl-N		: One property must exist for each entry in
+			  pinctrl-names.  See ../pinctrl/pinctrl-bindings.txt
+			  for details of the property values.
+- pinctrl-names		: Must contain a "default" entry.
+- reg			: Must contain an address for each entry in reg-names.
+- reg-names		: A list which must include the following entries:
+				* "mic-iomux"
+				* "spkr-iomux"
+- qcom,model		: Name of the sound card.
+
+Dai-link subnode properties and subnodes:
+
+Required dai-link subnodes:
+
+- cpu					: CPU   sub-node
+- codec					: CODEC sub-node
+
+Required CPU/CODEC subnodes properties:
+
+-link-name		: Name of the dai link.
+-sound-dai		: phandle and port of CPU/CODEC
+-capture-dai		: phandle and port of CPU/CODEC
+
+Example:
+
+sound: sound {
+	compatible = "qcom,apq8016-sbc-sndcard";
+	reg = <0x07702000 0x4>, <0x07702004 0x4>;
+	reg-names = "mic-iomux", "spkr-iomux";
+	qcom,model = "DB410c";
+
+	/* I2S - Internal codec */
+	internal-dai-link@0 {
+		cpu { /* PRIMARY */
+			sound-dai = <&lpass MI2S_PRIMARY>;
+		};
+		codec {
+			sound-dai = <&wcd_codec 0>;
+		};
+	};
+
+	/* External Primary or External Secondary -ADV7533 HDMI */
+	external-dai-link@0 {
+		link-name = "ADV7533";
+		cpu { /* QUAT */
+			sound-dai = <&lpass MI2S_QUATERNARY>;
+		};
+		codec {
+			sound-dai = <&adv_bridge 0>;
+		};
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt b/kernel/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt
index e00732dac..21c648328 100644
--- a/kernel/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt
@@ -4,12 +4,21 @@ This node models the Qualcomm Technologies Low-Power Audio SubSystem (LPASS).
 
 Required properties:
 
-- compatible		: "qcom,lpass-cpu"
+- compatible		: "qcom,lpass-cpu" or "qcom,apq8016-lpass-cpu"
 - clocks		: Must contain an entry for each entry in clock-names.
 - clock-names		: A list which must include the following entries:
 				* "ahbix-clk"
 				* "mi2s-osr-clk"
 				* "mi2s-bit-clk"
+			: required clocks for "qcom,lpass-cpu-apq8016"
+				* "ahbix-clk"
+				* "mi2s-bit-clk0"
+				* "mi2s-bit-clk1"
+				* "mi2s-bit-clk2"
+				* "mi2s-bit-clk3"
+				* "pcnoc-mport-clk"
+				* "pcnoc-sway-clk"
+
 - interrupts		: Must contain an entry for each entry in
 			  interrupt-names.
 - interrupt-names	: A list which must include the following entries:
@@ -22,6 +31,8 @@ Required properties:
 - reg-names		: A list which must include the following entries:
 				* "lpass-lpaif"
 
+
+
 Optional properties:
 
 - qcom,adsp		: Phandle for the audio DSP node
diff --git a/kernel/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/kernel/Documentation/devicetree/bindings/sound/renesas,rsnd.txt
index f316ce1f2..c57cbd657 100644
--- a/kernel/Documentation/devicetree/bindings/sound/renesas,rsnd.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/renesas,rsnd.txt
@@ -4,9 +4,12 @@ Required properties:
 - compatible			: "renesas,rcar_sound-<soctype>", fallbacks
 				  "renesas,rcar_sound-gen1" if generation1, and
 				  "renesas,rcar_sound-gen2" if generation2
+				  "renesas,rcar_sound-gen3" if generation3
 				  Examples with soctypes are:
+				    - "renesas,rcar_sound-r8a7778" (R-Car M1A)
 				    - "renesas,rcar_sound-r8a7790" (R-Car H2)
 				    - "renesas,rcar_sound-r8a7791" (R-Car M2-W)
+				    - "renesas,rcar_sound-r8a7795" (R-Car H3)
 - reg				: Should contain the register physical address.
 				  required register is
 				   SRU/ADG/SSI      if generation1
@@ -17,12 +20,23 @@ Required properties:
 - rcar_sound,src		: Should contain SRC feature.
 				  The number of SRC subnode should be same as HW.
 				  see below for detail.
+- rcar_sound,ctu		: Should contain CTU feature.
+				  The number of CTU subnode should be same as HW.
+				  see below for detail.
+- rcar_sound,mix		: Should contain MIX feature.
+				  The number of MIX subnode should be same as HW.
+				  see below for detail.
 - rcar_sound,dvc		: Should contain DVC feature.
 				  The number of DVC subnode should be same as HW.
 				  see below for detail.
 - rcar_sound,dai		: DAI contents.
 				  The number of DAI subnode should be same as HW.
 				  see below for detail.
+- #sound-dai-cells		: it must be 0 if your system is using single DAI
+				  it must be 1 if your system is using multi  DAI
+- #clock-cells			: it must be 0 if your system has audio_clkout
+				  it must be 1 if your system has audio_clkout0/1/2/3
+- clock-frequency		: for all audio_clkout0/1/2/3
 
 SSI subnode properties:
 - interrupts			: Should contain SSI interrupt for PIO transfer
@@ -47,7 +61,7 @@ DAI subnode properties:
 
 Example:
 
-rcar_sound: rcar_sound@ec500000 {
+rcar_sound: sound@ec500000 {
 	#sound-dai-cells = <1>;
 	compatible = "renesas,rcar_sound-r8a7791", "renesas,rcar_sound-gen2";
 	reg =	<0 0xec500000 0 0x1000>, /* SCU */
@@ -89,6 +103,22 @@ rcar_sound: rcar_sound@ec500000 {
 		};
 	};
 
+	rcar_sound,mix {
+		mix0: mix@0 { };
+		mix1: mix@1 { };
+	};
+
+	rcar_sound,ctu {
+		ctu00: ctu@0 { };
+		ctu01: ctu@1 { };
+		ctu02: ctu@2 { };
+		ctu03: ctu@3 { };
+		ctu10: ctu@4 { };
+		ctu11: ctu@5 { };
+		ctu12: ctu@6 { };
+		ctu13: ctu@7 { };
+	};
+
 	rcar_sound,src {
 		src0: src@0 {
 			interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/kernel/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt b/kernel/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt
index c64155027..962748a8d 100644
--- a/kernel/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt
@@ -6,6 +6,7 @@ Required properties:
 
 - compatible				: "renesas,rsrc-card,<board>"
 					  Examples with soctypes are:
+					    - "renesas,rsrc-card"
 					    - "renesas,rsrc-card,lager"
 					    - "renesas,rsrc-card,koelsch"
 Optional properties:
@@ -29,6 +30,12 @@ Optional subnode properties:
 - frame-inversion			: bool property. Add this if the
 					  dai-link uses frame clock inversion.
 - convert-rate				: platform specified sampling rate convert
+- audio-prefix				: see audio-routing
+- audio-routing				: A list of the connections between audio components.
+					  Each entry is a pair of strings, the first being the connection's sink,
+					  the second being the connection's source. Valid names for sources.
+					  use audio-prefix if some components is using same sink/sources naming.
+					  it can be used if compatible was "renesas,rsrc-card";
 
 Required CPU/CODEC subnodes properties:
 
diff --git a/kernel/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/kernel/Documentation/devicetree/bindings/sound/rockchip-i2s.txt
index 9b82c20b3..2267d249c 100644
--- a/kernel/Documentation/devicetree/bindings/sound/rockchip-i2s.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/rockchip-i2s.txt
@@ -12,8 +12,6 @@ Required properties:
 - reg: physical base address of the controller and length of memory mapped
   region.
 - interrupts: should contain the I2S interrupt.
-- #address-cells: should be 1.
-- #size-cells: should be 0.
 - dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
 	Documentation/devicetree/bindings/dma/dma.txt
 - dma-names: should include "tx" and "rx".
@@ -21,6 +19,7 @@ Required properties:
 - clock-names: should contain followings:
    - "i2s_hclk": clock for I2S BUS
    - "i2s_clk" : clock for I2S controller
+- rockchip,capture-channels: max capture channels, if not set, 2 channels default.
 
 Example for rk3288 I2S controller:
 
@@ -28,10 +27,9 @@ i2s@ff890000 {
 	compatible = "rockchip,rk3288-i2s", "rockchip,rk3066-i2s";
 	reg = <0xff890000 0x10000>;
 	interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
-	#address-cells = <1>;
-	#size-cells = <0>;
 	dmas = <&pdma1 0>, <&pdma1 1>;
 	dma-names = "tx", "rx";
 	clock-names = "i2s_hclk", "i2s_clk";
 	clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>;
+	rockchip,capture-channels = <2>;
 };
diff --git a/kernel/Documentation/devicetree/bindings/sound/rockchip-max98090.txt b/kernel/Documentation/devicetree/bindings/sound/rockchip-max98090.txt
new file mode 100644
index 000000000..a805aa99a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/rockchip-max98090.txt
@@ -0,0 +1,19 @@
+ROCKCHIP with MAX98090 CODEC
+
+Required properties:
+- compatible: "rockchip,rockchip-audio-max98090"
+- rockchip,model: The user-visible name of this sound complex
+- rockchip,i2s-controller: The phandle of the Rockchip I2S controller that's
+  connected to the CODEC
+- rockchip,audio-codec: The phandle of the MAX98090 audio codec
+- rockchip,headset-codec: The phandle of Ext chip for jack detection
+
+Example:
+
+sound {
+	compatible = "rockchip,rockchip-audio-max98090";
+	rockchip,model = "ROCKCHIP-I2S";
+	rockchip,i2s-controller = <&i2s>;
+	rockchip,audio-codec = <&max98090>;
+	rockchip,headset-codec = <&headsetcodec>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/rockchip-rt5645.txt b/kernel/Documentation/devicetree/bindings/sound/rockchip-rt5645.txt
new file mode 100644
index 000000000..411a62b3f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/rockchip-rt5645.txt
@@ -0,0 +1,17 @@
+ROCKCHIP with RT5645/RT5650 CODECS
+
+Required properties:
+- compatible: "rockchip,rockchip-audio-rt5645"
+- rockchip,model: The user-visible name of this sound complex
+- rockchip,i2s-controller: The phandle of the Rockchip I2S controller that's
+  connected to the CODEC
+- rockchip,audio-codec: The phandle of the RT5645/RT5650 audio codec
+
+Example:
+
+sound {
+	compatible = "rockchip,rockchip-audio-rt5645";
+	rockchip,model = "ROCKCHIP-I2S";
+	rockchip,i2s-controller = <&i2s>;
+	rockchip,audio-codec = <&rt5645>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/rockchip-spdif.txt b/kernel/Documentation/devicetree/bindings/sound/rockchip-spdif.txt
new file mode 100644
index 000000000..e64dbdea7
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/rockchip-spdif.txt
@@ -0,0 +1,40 @@
+* Rockchip SPDIF transceiver
+
+The S/PDIF audio block is a stereo transceiver that allows the
+processor to receive and transmit digital audio via an coaxial cable or
+a fibre cable.
+
+Required properties:
+
+- compatible: should be one of the following:
+   - "rockchip,rk3288-spdif", "rockchip,rk3188-spdif" or
+     "rockchip,rk3066-spdif"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: should contain the SPDIF interrupt.
+- dmas: DMA specifiers for tx dma. See the DMA client binding,
+  Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: should be "tx"
+- clocks: a list of phandle + clock-specifier pairs, one for each entry
+  in clock-names.
+- clock-names: should contain following:
+   - "hclk": clock for SPDIF controller
+   - "mclk" : clock for SPDIF bus
+
+Required properties on RK3288:
+  - rockchip,grf: the phandle of the syscon node for the general register
+                   file (GRF)
+
+Example for the rk3188 SPDIF controller:
+
+spdif: spdif@0x1011e000 {
+	compatible = "rockchip,rk3188-spdif", "rockchip,rk3066-spdif";
+	reg = <0x1011e000 0x2000>;
+	interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+	dmas = <&dmac1_s 8>;
+	dma-names = "tx";
+	clock-names = "hclk", "mclk";
+	clocks = <&cru HCLK_SPDIF>, <&cru SCLK_SPDIF>;
+	status = "disabled";
+	#sound-dai-cells = <0>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/rt5640.txt b/kernel/Documentation/devicetree/bindings/sound/rt5640.txt
index bac4d9ac1..9e62f6eb3 100644
--- a/kernel/Documentation/devicetree/bindings/sound/rt5640.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/rt5640.txt
@@ -14,7 +14,8 @@ Optional properties:
 
 - realtek,in1-differential
 - realtek,in2-differential
-  Boolean. Indicate MIC1/2 input are differential, rather than single-ended.
+- realtek,in3-differential
+  Boolean. Indicate MIC1/2/3 input are differential, rather than single-ended.
 
 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
 
@@ -24,9 +25,11 @@ Pins on the device (for linking into audio routes) for RT5639/RT5640:
   * DMIC2
   * MICBIAS1
   * IN1P
-  * IN1R
+  * IN1N
   * IN2P
-  * IN2R
+  * IN2N
+  * IN3P
+  * IN3N
   * HPOL
   * HPOR
   * LOUTL
diff --git a/kernel/Documentation/devicetree/bindings/sound/rt5645.txt b/kernel/Documentation/devicetree/bindings/sound/rt5645.txt
new file mode 100644
index 000000000..7cee1f518
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/rt5645.txt
@@ -0,0 +1,72 @@
+RT5650/RT5645 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+- compatible : One of "realtek,rt5645" or "realtek,rt5650".
+
+- reg : The I2C address of the device.
+
+- interrupts : The CODEC's interrupt output.
+
+Optional properties:
+
+- hp-detect-gpios:
+  a GPIO spec for the external headphone detect pin. If jd-mode = 0,
+  we will get the JD status by getting the value of hp-detect-gpios.
+
+- realtek,in2-differential
+  Boolean. Indicate MIC2 input are differential, rather than single-ended.
+
+- realtek,dmic1-data-pin
+  0: dmic1 is not used
+  1: using IN2P pin as dmic1 data pin
+  2: using GPIO6 pin as dmic1 data pin
+  3: using GPIO10 pin as dmic1 data pin
+  4: using GPIO12 pin as dmic1 data pin
+
+- realtek,dmic2-data-pin
+  0: dmic2 is not used
+  1: using IN2N pin as dmic2 data pin
+  2: using GPIO5 pin as dmic2 data pin
+  3: using GPIO11 pin as dmic2 data pin
+
+-- realtek,jd-mode : The JD mode of rt5645/rt5650
+   0 : rt5645/rt5650 JD function is not used
+   1 : Mode-0 (VDD=3.3V), two port jack detection
+   2 : Mode-1 (VDD=3.3V), one port jack detection
+   3 : Mode-2 (VDD=1.8V), one port jack detection
+
+Pins on the device (for linking into audio routes) for RT5645/RT5650:
+
+  * DMIC L1
+  * DMIC R1
+  * DMIC L2
+  * DMIC R2
+  * IN1P
+  * IN1N
+  * IN2P
+  * IN2N
+  * Haptic Generator
+  * HPOL
+  * HPOR
+  * LOUTL
+  * LOUTR
+  * PDM1L
+  * PDM1R
+  * SPOL
+  * SPOR
+
+Example:
+
+codec: rt5650@1a {
+	compatible = "realtek,rt5650";
+	reg = <0x1a>;
+	hp-detect-gpios = <&gpio 19 0>;
+	interrupt-parent = <&gpio>;
+	interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+	realtek,dmic-en = "true";
+	realtek,en-jd-func = "true";
+	realtek,jd-mode = <3>;
+};
\ No newline at end of file
diff --git a/kernel/Documentation/devicetree/bindings/sound/rt5677.txt b/kernel/Documentation/devicetree/bindings/sound/rt5677.txt
index 740ff771a..f07078997 100644
--- a/kernel/Documentation/devicetree/bindings/sound/rt5677.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/rt5677.txt
@@ -18,6 +18,7 @@ Required properties:
 Optional properties:
 
 - realtek,pow-ldo2-gpio : The GPIO that controls the CODEC's POW_LDO2 pin.
+- realtek,reset-gpio : The GPIO that controls the CODEC's RESET pin.
 
 - realtek,in1-differential
 - realtek,in2-differential
@@ -70,6 +71,7 @@ rt5677 {
 
 	realtek,pow-ldo2-gpio =
 		<&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+	realtek,reset-gpio = <&gpio TEGRA_GPIO(BB, 3) GPIO_ACTIVE_LOW>;
 	realtek,in1-differential = "true";
 	realtek,gpio-config = /bits/ 8  <0 0 0 0 0 2>;   /* pull up GPIO6 */
 	realtek,jd2-gpio = <3>;  /* Enables Jack detection for GPIO6 */
diff --git a/kernel/Documentation/devicetree/bindings/sound/simple-card.txt b/kernel/Documentation/devicetree/bindings/sound/simple-card.txt
index 73bf314f7..cf3979eb3 100644
--- a/kernel/Documentation/devicetree/bindings/sound/simple-card.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/simple-card.txt
@@ -16,7 +16,8 @@ Optional properties:
 					  connection's sink, the second being the connection's
 					  source.
 - simple-audio-card,mclk-fs             : Multiplication factor between stream rate and codec
-  					  mclk.
+					  mclk. When defined, mclk-fs property defined in
+					  dai-link sub nodes are ignored.
 - simple-audio-card,hp-det-gpio		: Reference to GPIO that signals when
 					  headphones are attached.
 - simple-audio-card,mic-det-gpio	: Reference to GPIO that signals when
@@ -55,6 +56,9 @@ Optional dai-link subnode properties:
 					  dai-link uses bit clock inversion.
 - frame-inversion			: bool property. Add this if the
 					  dai-link uses frame clock inversion.
+- mclk-fs             			: Multiplication factor between stream
+					  rate and codec mclk, applied only for
+					  the dai-link.
 
 For backward compatibility the frame-master and bitclock-master
 properties can be used as booleans in codec subnode to indicate if the
diff --git a/kernel/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt b/kernel/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt
new file mode 100644
index 000000000..028fa1c82
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt
@@ -0,0 +1,155 @@
+STMicroelectronics sti ASoC cards
+
+The sti ASoC Sound Card can be used, for all sti SoCs using internal sti-sas
+codec or external codecs.
+
+sti sound drivers allows to expose sti SoC audio interface through the
+generic ASoC simple card. For details about sound card declaration please refer to
+Documentation/devicetree/bindings/sound/simple-card.txt.
+
+1) sti-uniperiph-dai: audio dai device.
+---------------------------------------
+
+Required properties:
+  - compatible: "st,sti-uni-player" or "st,sti-uni-reader"
+
+  - st,syscfg: phandle to boot-device system configuration registers
+
+  - clock-names: name of the clocks listed in clocks property in the same order
+
+  - reg: CPU DAI IP Base address and size entries, listed  in same
+	 order than the CPU_DAI properties.
+
+  - reg-names: names of the mapped memory regions listed in regs property in
+	       the same order.
+
+  - interrupts: CPU_DAI interrupt line, listed in the same order than the
+		CPU_DAI properties.
+
+  - dma: CPU_DAI DMA controller phandle and DMA request line, listed in the same
+	 order than the CPU_DAI properties.
+
+  - dma-names: identifier string for each DMA request line in the dmas property.
+	"tx" for "st,sti-uni-player" compatibility
+	"rx" for "st,sti-uni-reader" compatibility
+
+  - version: IP version integrated in SOC.
+
+  - dai-name: DAI name that describes the IP.
+
+Required properties ("st,sti-uni-player" compatibility only):
+  - clocks: CPU_DAI IP clock source, listed in the same order than the
+	    CPU_DAI properties.
+
+  - uniperiph-id: internal SOC IP instance ID.
+
+  - IP mode: IP working mode depending on associated codec.
+	"HDMI" connected to HDMI codec IP and IEC HDMI formats.
+	"SPDIF"connected to SPDIF codec and support SPDIF formats.
+	"PCM"  PCM standard mode for I2S or TDM bus.
+
+Optional properties:
+  - pinctrl-0: defined for CPU_DAI@1 and CPU_DAI@4 to describe I2S PIOs for
+	       external codecs connection.
+
+  - pinctrl-names: should contain only one value - "default".
+
+Example:
+
+	sti_uni_player2: sti-uni-player@2 {
+		compatible = "st,sti-uni-player";
+		status = "okay";
+		#sound-dai-cells = <0>;
+		st,syscfg = <&syscfg_core>;
+		clocks = <&clk_s_d0_flexgen CLK_PCM_2>;
+		reg = <0x8D82000 0x158>;
+		interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
+		dmas = <&fdma0 4 0 1>;
+		dai-name = "Uni Player #1 (DAC)";
+		dma-names = "tx";
+		uniperiph-id = <2>;
+		version = <5>;
+		mode = "PCM";
+	};
+
+	sti_uni_player3: sti-uni-player@3 {
+		compatible = "st,sti-uni-player";
+		status = "okay";
+		#sound-dai-cells = <0>;
+		st,syscfg = <&syscfg_core>;
+		clocks = <&clk_s_d0_flexgen CLK_SPDIFF>;
+		reg = <0x8D85000 0x158>;
+		interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>;
+		dmas = <&fdma0 7 0 1>;
+		dma-names = "tx";
+		dai-name = "Uni Player #1 (PIO)";
+		uniperiph-id = <3>;
+		version = <5>;
+		mode = "SPDIF";
+	};
+
+	sti_uni_reader1: sti-uni-reader@1 {
+		compatible = "st,sti-uni-reader";
+		status = "disabled";
+		#sound-dai-cells = <0>;
+		st,syscfg = <&syscfg_core>;
+		reg = <0x8D84000 0x158>;
+		interrupts = <GIC_SPI 88 IRQ_TYPE_NONE>;
+		dmas = <&fdma0 6 0 1>;
+		dma-names = "rx";
+		dai-name = "Uni Reader #1 (HDMI RX)";
+		version = <3>;
+	};
+
+2) sti-sas-codec: internal audio codec IPs driver
+-------------------------------------------------
+
+Required properties:
+  - compatible: "st,sti<chip>-sas-codec" .
+	Should be chip "st,stih416-sas-codec" or "st,stih407-sas-codec"
+
+  - st,syscfg: phandle to boot-device system configuration registers.
+
+  - pinctrl-0: SPDIF PIO description.
+
+  - pinctrl-names: should contain only one value - "default".
+
+Example:
+	sti_sas_codec: sti-sas-codec {
+		compatible = "st,stih407-sas-codec";
+		#sound-dai-cells = <1>;
+		st,reg_audio = <&syscfg_core>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_spdif_out >;
+	};
+
+Example of audio card declaration:
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "sti audio card";
+		status = "okay";
+
+		simple-audio-card,dai-link@0 {
+			/* DAC */
+			format = "i2s";
+			dai-tdm-slot-width = <32>;
+			cpu {
+				sound-dai = <&sti_uni_player2>;
+			};
+
+			codec {
+				sound-dai = <&sti_sasg_codec 1>;
+			};
+		};
+		simple-audio-card,dai-link@1 {
+			/* SPDIF */
+			format = "left_j";
+			cpu {
+				sound-dai = <&sti_uni_player3>;
+			};
+
+			codec {
+				sound-dai = <&sti_sasg_codec 0>;
+			};
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/sun4i-codec.txt b/kernel/Documentation/devicetree/bindings/sound/sun4i-codec.txt
new file mode 100644
index 000000000..c92966bd5
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/sun4i-codec.txt
@@ -0,0 +1,27 @@
+* Allwinner A10 Codec
+
+Required properties:
+- compatible: must be either "allwinner,sun4i-a10-codec" or
+  "allwinner,sun7i-a20-codec"
+- reg: must contain the registers location and length
+- interrupts: must contain the codec interrupt
+- dmas: DMA channels for tx and rx dma. See the DMA client binding,
+	Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: should include "tx" and "rx".
+- clocks: a list of phandle + clock-specifer pairs, one for each entry
+  in clock-names.
+- clock-names: should contain followings:
+   - "apb": the parent APB clock for this controller
+   - "codec": the parent module clock
+
+Example:
+codec: codec@01c22c00 {
+	#sound-dai-cells = <0>;
+	compatible = "allwinner,sun7i-a20-codec";
+	reg = <0x01c22c00 0x40>;
+	interrupts = <0 30 4>;
+	clocks = <&apb0_gates 0>, <&codec_clk>;
+	clock-names = "apb", "codec";
+	dmas = <&dma 0 19>, <&dma 0 19>;
+	dma-names = "rx", "tx";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/tas2552.txt b/kernel/Documentation/devicetree/bindings/sound/tas2552.txt
index 55e2a0af5..c49992c0b 100644
--- a/kernel/Documentation/devicetree/bindings/sound/tas2552.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/tas2552.txt
@@ -14,6 +14,12 @@ Required properties:
 Optional properties:
 	- enable-gpio - gpio pin to enable/disable the device
 
+tas2552 can receive it's reference clock via MCLK, BCLK, IVCLKIN pin or use the
+internal 1.8MHz. This CLKIN is used by the PLL. In addition to PLL, the PDM
+reference clock is also selectable: PLL, IVCLKIN, BCLK or MCLK.
+For system integration the dt-bindings/sound/tas2552.h header file provides
+defined values to selct and configure the PLL and PDM reference clocks.
+
 Example:
 
 tas2552: tas2552@41 {
diff --git a/kernel/Documentation/devicetree/bindings/sound/tas571x.txt b/kernel/Documentation/devicetree/bindings/sound/tas571x.txt
new file mode 100644
index 000000000..0ac31d8d5
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/tas571x.txt
@@ -0,0 +1,41 @@
+Texas Instruments TAS5711/TAS5717/TAS5719 stereo power amplifiers
+
+The codec is controlled through an I2C interface.  It also has two other
+signals that can be wired up to GPIOs: reset (strongly recommended), and
+powerdown (optional).
+
+Required properties:
+
+- compatible: "ti,tas5711", "ti,tas5717", or "ti,tas5719"
+- reg: The I2C address of the device
+- #sound-dai-cells: must be equal to 0
+
+Optional properties:
+
+- reset-gpios: GPIO specifier for the TAS571x's active low reset line
+- pdn-gpios: GPIO specifier for the TAS571x's active low powerdown line
+- clocks: clock phandle for the MCLK input
+- clock-names: should be "mclk"
+- AVDD-supply: regulator phandle for the AVDD supply (all chips)
+- DVDD-supply: regulator phandle for the DVDD supply (all chips)
+- HPVDD-supply: regulator phandle for the HPVDD supply (5717/5719)
+- PVDD_AB-supply: regulator phandle for the PVDD_AB supply (5717/5719)
+- PVDD_CD-supply: regulator phandle for the PVDD_CD supply (5717/5719)
+- PVDD_A-supply: regulator phandle for the PVDD_A supply (5711)
+- PVDD_B-supply: regulator phandle for the PVDD_B supply (5711)
+- PVDD_C-supply: regulator phandle for the PVDD_C supply (5711)
+- PVDD_D-supply: regulator phandle for the PVDD_D supply (5711)
+
+Example:
+
+	tas5717: audio-codec@2a {
+		compatible = "ti,tas5717";
+		reg = <0x2a>;
+		#sound-dai-cells = <0>;
+
+		reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+		pdn-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+
+		clocks = <&clk_core CLK_I2S>;
+		clock-names = "mclk";
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/tdm-slot.txt b/kernel/Documentation/devicetree/bindings/sound/tdm-slot.txt
index 6a2c84247..34cf70e2c 100644
--- a/kernel/Documentation/devicetree/bindings/sound/tdm-slot.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/tdm-slot.txt
@@ -4,11 +4,15 @@ This specifies audio DAI's TDM slot.
 
 TDM slot properties:
 dai-tdm-slot-num : Number of slots in use.
-dai-tdm-slot-width :  Width in bits for each slot.
+dai-tdm-slot-width : Width in bits for each slot.
+dai-tdm-slot-tx-mask : Transmit direction slot mask, optional
+dai-tdm-slot-rx-mask : Receive direction slot mask, optional
 
 For instance:
 	dai-tdm-slot-num = <2>;
 	dai-tdm-slot-width = <8>;
+	dai-tdm-slot-tx-mask = <0 1>;
+	dai-tdm-slot-rx-mask = <1 0>;
 
 And for each spcified driver, there could be one .of_xlate_tdm_slot_mask()
 to specify a explicit mapping of the channels and the slots. If it's absent
@@ -18,3 +22,8 @@ tx and rx masks.
 For snd_soc_of_xlate_tdm_slot_mask(), the tx and rx masks will use a 1 bit
 for an active slot as default, and the default active bits are at the LSB of
 the masks.
+
+The explicit masks are given as array of integers, where the first
+number presents bit-0 (LSB), second presents bit-1, etc. Any non zero
+number is considered 1 and 0 is 0. snd_soc_of_xlate_tdm_slot_mask()
+does not do anything, if either mask is set non zero value.
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8741.txt b/kernel/Documentation/devicetree/bindings/sound/wm8741.txt
index 74bda58c1..a13315408 100644
--- a/kernel/Documentation/devicetree/bindings/sound/wm8741.txt
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8741.txt
@@ -10,9 +10,20 @@ Required properties:
   - reg : the I2C address of the device for I2C, the chip select
           number for SPI.
 
+Optional properties:
+
+  - diff-mode: Differential output mode configuration. Default value for field
+    DIFF in register R8 (MODE_CONTROL_2). If absent, the default is 0, shall be:
+    0 = stereo
+    1 = mono left
+    2 = stereo reversed
+    3 = mono right
+
 Example:
 
 codec: wm8741@1a {
 	compatible = "wlf,wm8741";
 	reg = <0x1a>;
+
+	diff-mode = <3>;
 };
diff --git a/kernel/Documentation/devicetree/bindings/sound/zte,zx-i2s.txt b/kernel/Documentation/devicetree/bindings/sound/zte,zx-i2s.txt
new file mode 100644
index 000000000..7e5aa6f6b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/zte,zx-i2s.txt
@@ -0,0 +1,44 @@
+ZTE ZX296702 I2S controller
+
+Required properties:
+ - compatible : Must be "zte,zx296702-i2s"
+ - reg : Must contain I2S core's registers location and length
+ - clocks : Pairs of phandle and specifier referencing the controller's clocks.
+ - clock-names: "tx" for the clock to the I2S interface.
+ - dmas: Pairs of phandle and specifier for the DMA channel that is used by
+   the core. The core expects two dma channels for transmit.
+ - dma-names : Must be "tx" and "rx"
+
+For more details on the 'dma', 'dma-names', 'clock' and 'clock-names' properties
+please check:
+	* resource-names.txt
+	* clock/clock-bindings.txt
+	* dma/dma.txt
+
+Example:
+	i2s0: i2s0@0b005000 {
+		#sound-dai-cells = <0>;
+		compatible = "zte,zx296702-i2s";
+		reg = <0x0b005000 0x1000>;
+		clocks = <&lsp0clk ZX296702_I2S0_DIV>;
+		clock-names = "tx";
+		interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+		dmas = <&dma 5>, <&dma 6>;
+		dma-names = "tx", "rx";
+		status = "okay";
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "zx296702_snd";
+		simple-audio-card,format = "left_j";
+		simple-audio-card,bitclock-master = <&sndcodec>;
+		simple-audio-card,frame-master = <&sndcodec>;
+		sndcpu: simple-audio-card,cpu {
+			sound-dai = <&i2s0>;
+		};
+
+		sndcodec: simple-audio-card,codec {
+			sound-dai = <&acodec>;
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/zte,zx-spdif.txt b/kernel/Documentation/devicetree/bindings/sound/zte,zx-spdif.txt
new file mode 100644
index 000000000..989544ea6
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/zte,zx-spdif.txt
@@ -0,0 +1,28 @@
+ZTE ZX296702 SPDIF controller
+
+Required properties:
+ - compatible : Must be "zte,zx296702-spdif"
+ - reg : Must contain SPDIF core's registers location and length
+ - clocks : Pairs of phandle and specifier referencing the controller's clocks.
+ - clock-names: "tx" for the clock to the SPDIF interface.
+ - dmas: Pairs of phandle and specifier for the DMA channel that is used by
+   the core. The core expects one dma channel for transmit.
+ - dma-names : Must be "tx"
+
+For more details on the 'dma', 'dma-names', 'clock' and 'clock-names' properties
+please check:
+	* resource-names.txt
+	* clock/clock-bindings.txt
+	* dma/dma.txt
+
+Example:
+	spdif0: spdif0@0b004000 {
+		compatible = "zte,zx296702-spdif";
+		reg = <0x0b004000 0x1000>;
+		clocks = <&lsp0clk ZX296702_SPDIF0_DIV>;
+		clock-names = "tx";
+		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+		dmas = <&dma 4>;
+		dma-names = "tx";
+		status = "okay";
+	};