Add the rt linux 4.1.3-rt3 as base

Import the rt linux 4.1.3-rt3 as OPNFV kvm base.

It's from git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git linux-4.1.y-rt and
the base is:

commit 0917f823c59692d751951bf5ea699a2d1e2f26a2
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date:   Sat Jul 25 12:13:34 2015 +0200

    Prepare v4.1.3-rt3

    Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>

We lose all the git history this way and it's not good. We
should apply another opnfv project repo in future.

Change-Id: I87543d81c9df70d99c5001fbdf646b202c19f423
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>

1 files changed, 92 insertions, 0 deletions

diff --git a/kernel/Documentation/devicetree/bindings/regulator/regulator.txt b/kernel/Documentation/devicetree/bindings/regulator/regulator.txt
new file mode 100644
index 000000000..abb26b58c
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -0,0 +1,92 @@
+Voltage/Current Regulators
+
+Optional properties:
+- regulator-name: A string used as a descriptive name for regulator outputs
+- regulator-min-microvolt: smallest voltage consumers may set
+- regulator-max-microvolt: largest voltage consumers may set
+- regulator-microvolt-offset: Offset applied to voltages to compensate for voltage drops
+- regulator-min-microamp: smallest current consumers may set
+- regulator-max-microamp: largest current consumers may set
+- regulator-always-on: boolean, regulator should never be disabled
+- regulator-boot-on: bootloader/firmware enabled regulator
+- regulator-allow-bypass: allow the regulator to go into bypass mode
+- <name>-supply: phandle to the parent supply/regulator node
+- regulator-ramp-delay: ramp delay for regulator(in uV/uS)
+  For hardware which supports disabling ramp rate, it should be explicitly
+  intialised to zero (regulator-ramp-delay = <0>) for disabling ramp delay.
+- regulator-enable-ramp-delay: The time taken, in microseconds, for the supply
+  rail to reach the target voltage, plus/minus whatever tolerance the board
+  design requires. This property describes the total system ramp time
+  required due to the combination of internal ramping of the regulator itself,
+  and board design issues such as trace capacitance and load on the supply.
+- regulator-state-mem sub-root node for Suspend-to-RAM mode
+  : suspend to memory, the device goes to sleep, but all data stored in memory,
+  only some external interrupt can wake the device.
+- regulator-state-disk sub-root node for Suspend-to-DISK mode
+  : suspend to disk, this state operates similarly to Suspend-to-RAM,
+  but includes a final step of writing memory contents to disk.
+- regulator-state-[mem/disk] node has following common properties:
+	- regulator-on-in-suspend: regulator should be on in suspend state.
+	- regulator-off-in-suspend: regulator should be off in suspend state.
+	- regulator-suspend-microvolt: regulator should be set to this voltage
+	  in suspend.
+	- regulator-mode: operating mode in the given suspend state.
+	  The set of possible operating modes depends on the capabilities of
+	  every hardware so the valid modes are documented on each regulator
+	  device tree binding document.
+- regulator-initial-mode: initial operating mode. The set of possible operating
+  modes depends on the capabilities of every hardware so each device binding
+  documentation explains which values the regulator supports.
+
+Deprecated properties:
+- regulator-compatible: If a regulator chip contains multiple
+  regulators, and if the chip's binding contains a child node that
+  describes each regulator, then this property indicates which regulator
+  this child node is intended to configure. If this property is missing,
+  the node's name will be used instead.
+
+Example:
+
+	xyzreg: regulator@0 {
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+		vin-supply = <&vin>;
+
+		regulator-state-mem {
+			regulator-on-in-suspend;
+		};
+	};
+
+Regulator Consumers:
+Consumer nodes can reference one or more of its supplies/
+regulators using the below bindings.
+
+- <name>-supply: phandle to the regulator node
+
+These are the same bindings that a regulator in the above
+example used to reference its own supply, in which case
+its just seen as a special case of a regulator being a
+consumer itself.
+
+Example of a consumer device node (mmc) referencing two
+regulators (twl_reg1 and twl_reg2),
+
+	twl_reg1: regulator@0 {
+		...
+		...
+		...
+	};
+
+	twl_reg2: regulator@1 {
+		...
+		...
+		...
+	};
+
+	mmc: mmc@0x0 {
+		...
+		...
+		vmmc-supply = <&twl_reg1>;
+		vmmcaux-supply = <&twl_reg2>;
+	};