These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

6 files changed, 75 insertions, 108 deletions

diff --git a/kernel/Documentation/devicetree/bindings/powerpc/fsl/board.txt b/kernel/Documentation/devicetree/bindings/powerpc/fsl/board.txt
deleted file mode 100644
index cff38bdbc..000000000
--- a/kernel/Documentation/devicetree/bindings/powerpc/fsl/board.txt
+++ /dev/null
@@ -1,102 +0,0 @@
-Freescale Reference Board Bindings
-
-This document describes device tree bindings for various devices that
-exist on some Freescale reference boards.
-
-* Board Control and Status (BCSR)
-
-Required properties:
-
- - compatible : Should be "fsl,<board>-bcsr"
- - reg : Offset and length of the register set for the device
-
-Example:
-
-	bcsr@f8000000 {
-		compatible = "fsl,mpc8360mds-bcsr";
-		reg = <f8000000 8000>;
-	};
-
-* Freescale on-board FPGA
-
-This is the memory-mapped registers for on board FPGA.
-
-Required properities:
-- compatible: should be a board-specific string followed by a string
-  indicating the type of FPGA.  Example:
-	"fsl,<board>-fpga", "fsl,fpga-pixis"
-- reg: should contain the address and the length of the FPGA register set.
-- interrupt-parent: should specify phandle for the interrupt controller.
-- interrupts: should specify event (wakeup) IRQ.
-
-Example (P1022DS):
-
-	 board-control@3,0 {
-		 compatible = "fsl,p1022ds-fpga", "fsl,fpga-ngpixis";
-		 reg = <3 0 0x30>;
-		 interrupt-parent = <&mpic>;
-		 interrupts = <8 8 0 0>;
-	 };
-
-* Freescale BCSR GPIO banks
-
-Some BCSR registers act as simple GPIO controllers, each such
-register can be represented by the gpio-controller node.
-
-Required properities:
-- compatible : Should be "fsl,<board>-bcsr-gpio".
-- reg : Should contain the address and the length of the GPIO bank
-  register.
-- #gpio-cells : Should be two. The first cell is the pin number and the
-  second cell is used to specify optional parameters (currently unused).
-- gpio-controller : Marks the port as GPIO controller.
-
-Example:
-
-	bcsr@1,0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "fsl,mpc8360mds-bcsr";
-		reg = <1 0 0x8000>;
-		ranges = <0 1 0 0x8000>;
-
-		bcsr13: gpio-controller@d {
-			#gpio-cells = <2>;
-			compatible = "fsl,mpc8360mds-bcsr-gpio";
-			reg = <0xd 1>;
-			gpio-controller;
-		};
-	};
-
-* Freescale on-board FPGA connected on I2C bus
-
-Some Freescale boards like BSC9132QDS have on board FPGA connected on
-the i2c bus.
-
-Required properties:
-- compatible: Should be a board-specific string followed by a string
-  indicating the type of FPGA.  Example:
-	"fsl,<board>-fpga", "fsl,fpga-qixis-i2c"
-- reg: Should contain the address of the FPGA
-
-Example:
-	fpga: fpga@66 {
-		compatible = "fsl,bsc9132qds-fpga", "fsl,fpga-qixis-i2c";
-		reg = <0x66>;
-	};
-
-* Freescale on-board CPLD
-
-Some Freescale boards like T1040RDB have an on board CPLD connected.
-
-Required properties:
-- compatible: Should be a board-specific string like "fsl,<board>-cpld"
-  Example:
-	"fsl,t1040rdb-cpld", "fsl,t1042rdb-cpld", "fsl,t1042rdb_pi-cpld"
-- reg: should describe CPLD registers
-
-Example:
-	cpld@3,0 {
-		compatible = "fsl,t1040rdb-cpld";
-		reg = <3 0 0x300>;
-	};
diff --git a/kernel/Documentation/devicetree/bindings/powerpc/fsl/fman.txt b/kernel/Documentation/devicetree/bindings/powerpc/fsl/fman.txt
index edda55f74..1fc5328c0 100644
--- a/kernel/Documentation/devicetree/bindings/powerpc/fsl/fman.txt
+++ b/kernel/Documentation/devicetree/bindings/powerpc/fsl/fman.txt
@@ -189,6 +189,19 @@ PROPERTIES
 		Definition: There is one reg region describing the port
 		configuration registers.
 
+- fsl,fman-10g-port
+		Usage: optional
+		Value type: boolean
+		Definition: The default port rate is 1G.
+		If this property exists, the port is s 10G port.
+
+- fsl,fman-best-effort-port
+		Usage: optional
+		Value type: boolean
+		Definition: Can be defined only if 10G-support is set.
+		This property marks a best-effort 10G port (10G port that
+		may not be capable of line rate).
+
 EXAMPLE
 
 port@a8000 {
diff --git a/kernel/Documentation/devicetree/bindings/powerpc/fsl/guts.txt b/kernel/Documentation/devicetree/bindings/powerpc/fsl/guts.txt
index 7f150b501..b71b2039e 100644
--- a/kernel/Documentation/devicetree/bindings/powerpc/fsl/guts.txt
+++ b/kernel/Documentation/devicetree/bindings/powerpc/fsl/guts.txt
@@ -9,6 +9,11 @@ Required properties:
 
  - compatible : Should define the compatible device type for
    global-utilities.
+   Possible compatibles:
+	"fsl,qoriq-device-config-1.0"
+	"fsl,qoriq-device-config-2.0"
+	"fsl,<chip>-device-config"
+	"fsl,<chip>-guts"
  - reg : Offset and length of the register set for the device.
 
 Recommended properties:
diff --git a/kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt b/kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt
index 8832e8798..647817527 100644
--- a/kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt
+++ b/kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt
@@ -6,14 +6,14 @@ PSC in UART mode
 For PSC in UART mode the needed PSC serial devices
 are specified by fsl,mpc5121-psc-uart nodes in the
 fsl,mpc5121-immr SoC node. Additionally the PSC FIFO
-Controller node fsl,mpc5121-psc-fifo is requered there:
+Controller node fsl,mpc5121-psc-fifo is required there:
 
-fsl,mpc5121-psc-uart nodes
+fsl,mpc512x-psc-uart nodes
 --------------------------
 
 Required properties :
- - compatible : Should contain "fsl,mpc5121-psc-uart" and "fsl,mpc5121-psc"
- - cell-index : Index of the PSC in hardware
+ - compatible : Should contain "fsl,<soc>-psc-uart" and "fsl,<soc>-psc"
+   Supported <soc>s: mpc5121, mpc5125
  - reg : Offset and length of the register set for the PSC device
  - interrupts : <a b> where a is the interrupt number of the
    PSC FIFO Controller and b is a field that represents an
@@ -25,12 +25,21 @@ Recommended properties :
  - fsl,rx-fifo-size : the size of the RX fifo slice (a multiple of 4)
  - fsl,tx-fifo-size : the size of the TX fifo slice (a multiple of 4)
 
+PSC in SPI mode
+---------------
 
-fsl,mpc5121-psc-fifo node
+Similar to the UART mode a PSC can be operated in SPI mode. The compatible used
+for that is fsl,mpc5121-psc-spi. It requires a fsl,mpc5121-psc-fifo as well.
+The required and recommended properties are identical to the
+fsl,mpc5121-psc-uart nodes, just use spi instead of uart in the compatible
+string.
+
+fsl,mpc512x-psc-fifo node
 -------------------------
 
 Required properties :
- - compatible : Should be "fsl,mpc5121-psc-fifo"
+ - compatible : Should be "fsl,<soc>-psc-fifo"
+   Supported <soc>s: mpc5121, mpc5125
  - reg : Offset and length of the register set for the PSC
          FIFO Controller
  - interrupts : <a b> where a is the interrupt number of the
@@ -39,6 +48,9 @@ Required properties :
  - interrupt-parent : the phandle for the interrupt controller that
    services interrupts for this device.
 
+Recommended properties :
+ - clocks : specifies the clock needed to operate the fifo controller
+ - clock-names : name(s) for the clock(s) listed in clocks
 
 Example for a board using PSC0 and PSC1 devices in serial mode:
 
diff --git a/kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc512x_lpbfifo.txt b/kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc512x_lpbfifo.txt
new file mode 100644
index 000000000..b3b392fe1
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc512x_lpbfifo.txt
@@ -0,0 +1,21 @@
+Freescale MPC512x LocalPlus Bus FIFO (called SCLPC in the Reference Manual)
+
+Required properties:
+- compatible: should be "fsl,mpc512x-lpbfifo";
+- reg: should contain the offset and length of SCLPC register set;
+- interrupts: should contain the interrupt specifier for SCLPC; syntax of an
+    interrupt client node is described in interrupt-controller/interrupts.txt;
+- dmas: should contain the DMA specifier for SCLPC as described at
+    dma/dma.txt and dma/mpc512x-dma.txt;
+- dma-names: should be "rx-tx";
+
+Example:
+
+	sclpc@10100 {
+		compatible = "fsl,mpc512x-lpbfifo";
+		reg = <0x10100 0x50>;
+		interrupts = <7 0x8>;
+		dmas = <&dma0 26>;
+		dma-names = "rx-tx";
+	};
+
diff --git a/kernel/Documentation/devicetree/bindings/powerpc/fsl/scfg.txt b/kernel/Documentation/devicetree/bindings/powerpc/fsl/scfg.txt
new file mode 100644
index 000000000..0532c46b3
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/powerpc/fsl/scfg.txt
@@ -0,0 +1,18 @@
+Freescale Supplement configuration unit (SCFG)
+
+SCFG is the supplemental configuration unit, that provides SoC specific
+configuration and status registers for the chip. Such as getting PEX port
+status.
+
+Required properties:
+
+- compatible: should be "fsl,<chip>-scfg"
+- reg: should contain base address and length of SCFG memory-mapped
+registers
+
+Example:
+
+	scfg: global-utilities@fc000 {
+		compatible = "fsl,t1040-scfg";
+		reg = <0xfc000 0x1000>;
+	};