From e09b41010ba33a20a87472ee821fa407a5b8da36 Mon Sep 17 00:00:00 2001 From: José Pekkarinen Date: Mon, 11 Apr 2016 10:41:07 +0300 Subject: These changes are the raw update to linux-4.4.6-rt14. Kernel sources are taken from kernel.org, and rt patch from the rt wiki download page. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit During the rebasing, the following patch collided: Force tick interrupt and get rid of softirq magic(I70131fb85). Collisions have been removed because its logic was found on the source already. Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769 Signed-off-by: José Pekkarinen --- .../devicetree/bindings/powerpc/fsl/board.txt | 102 --------------------- .../devicetree/bindings/powerpc/fsl/fman.txt | 13 +++ .../devicetree/bindings/powerpc/fsl/guts.txt | 5 + .../bindings/powerpc/fsl/mpc5121-psc.txt | 24 +++-- .../bindings/powerpc/fsl/mpc512x_lpbfifo.txt | 21 +++++ .../devicetree/bindings/powerpc/fsl/scfg.txt | 18 ++++ 6 files changed, 75 insertions(+), 108 deletions(-) delete mode 100644 kernel/Documentation/devicetree/bindings/powerpc/fsl/board.txt create mode 100644 kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc512x_lpbfifo.txt create mode 100644 kernel/Documentation/devicetree/bindings/powerpc/fsl/scfg.txt (limited to 'kernel/Documentation/devicetree/bindings/powerpc') diff --git a/kernel/Documentation/devicetree/bindings/powerpc/fsl/board.txt b/kernel/Documentation/devicetree/bindings/powerpc/fsl/board.txt deleted file mode 100644 index cff38bdbc..000000000 --- a/kernel/Documentation/devicetree/bindings/powerpc/fsl/board.txt +++ /dev/null @@ -1,102 +0,0 @@ -Freescale Reference Board Bindings - -This document describes device tree bindings for various devices that -exist on some Freescale reference boards. - -* Board Control and Status (BCSR) - -Required properties: - - - compatible : Should be "fsl,-bcsr" - - reg : Offset and length of the register set for the device - -Example: - - bcsr@f8000000 { - compatible = "fsl,mpc8360mds-bcsr"; - reg = ; - }; - -* Freescale on-board FPGA - -This is the memory-mapped registers for on board FPGA. - -Required properities: -- compatible: should be a board-specific string followed by a string - indicating the type of FPGA. Example: - "fsl,-fpga", "fsl,fpga-pixis" -- reg: should contain the address and the length of the FPGA register set. -- interrupt-parent: should specify phandle for the interrupt controller. -- interrupts: should specify event (wakeup) IRQ. - -Example (P1022DS): - - board-control@3,0 { - compatible = "fsl,p1022ds-fpga", "fsl,fpga-ngpixis"; - reg = <3 0 0x30>; - interrupt-parent = <&mpic>; - interrupts = <8 8 0 0>; - }; - -* Freescale BCSR GPIO banks - -Some BCSR registers act as simple GPIO controllers, each such -register can be represented by the gpio-controller node. - -Required properities: -- compatible : Should be "fsl,-bcsr-gpio". -- reg : Should contain the address and the length of the GPIO bank - register. -- #gpio-cells : Should be two. The first cell is the pin number and the - second cell is used to specify optional parameters (currently unused). -- gpio-controller : Marks the port as GPIO controller. - -Example: - - bcsr@1,0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc8360mds-bcsr"; - reg = <1 0 0x8000>; - ranges = <0 1 0 0x8000>; - - bcsr13: gpio-controller@d { - #gpio-cells = <2>; - compatible = "fsl,mpc8360mds-bcsr-gpio"; - reg = <0xd 1>; - gpio-controller; - }; - }; - -* Freescale on-board FPGA connected on I2C bus - -Some Freescale boards like BSC9132QDS have on board FPGA connected on -the i2c bus. - -Required properties: -- compatible: Should be a board-specific string followed by a string - indicating the type of FPGA. Example: - "fsl,-fpga", "fsl,fpga-qixis-i2c" -- reg: Should contain the address of the FPGA - -Example: - fpga: fpga@66 { - compatible = "fsl,bsc9132qds-fpga", "fsl,fpga-qixis-i2c"; - reg = <0x66>; - }; - -* Freescale on-board CPLD - -Some Freescale boards like T1040RDB have an on board CPLD connected. - -Required properties: -- compatible: Should be a board-specific string like "fsl,-cpld" - Example: - "fsl,t1040rdb-cpld", "fsl,t1042rdb-cpld", "fsl,t1042rdb_pi-cpld" -- reg: should describe CPLD registers - -Example: - cpld@3,0 { - compatible = "fsl,t1040rdb-cpld"; - reg = <3 0 0x300>; - }; diff --git a/kernel/Documentation/devicetree/bindings/powerpc/fsl/fman.txt b/kernel/Documentation/devicetree/bindings/powerpc/fsl/fman.txt index edda55f74..1fc5328c0 100644 --- a/kernel/Documentation/devicetree/bindings/powerpc/fsl/fman.txt +++ b/kernel/Documentation/devicetree/bindings/powerpc/fsl/fman.txt @@ -189,6 +189,19 @@ PROPERTIES Definition: There is one reg region describing the port configuration registers. +- fsl,fman-10g-port + Usage: optional + Value type: boolean + Definition: The default port rate is 1G. + If this property exists, the port is s 10G port. + +- fsl,fman-best-effort-port + Usage: optional + Value type: boolean + Definition: Can be defined only if 10G-support is set. + This property marks a best-effort 10G port (10G port that + may not be capable of line rate). + EXAMPLE port@a8000 { diff --git a/kernel/Documentation/devicetree/bindings/powerpc/fsl/guts.txt b/kernel/Documentation/devicetree/bindings/powerpc/fsl/guts.txt index 7f150b501..b71b2039e 100644 --- a/kernel/Documentation/devicetree/bindings/powerpc/fsl/guts.txt +++ b/kernel/Documentation/devicetree/bindings/powerpc/fsl/guts.txt @@ -9,6 +9,11 @@ Required properties: - compatible : Should define the compatible device type for global-utilities. + Possible compatibles: + "fsl,qoriq-device-config-1.0" + "fsl,qoriq-device-config-2.0" + "fsl,-device-config" + "fsl,-guts" - reg : Offset and length of the register set for the device. Recommended properties: diff --git a/kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt b/kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt index 8832e8798..647817527 100644 --- a/kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt +++ b/kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt @@ -6,14 +6,14 @@ PSC in UART mode For PSC in UART mode the needed PSC serial devices are specified by fsl,mpc5121-psc-uart nodes in the fsl,mpc5121-immr SoC node. Additionally the PSC FIFO -Controller node fsl,mpc5121-psc-fifo is requered there: +Controller node fsl,mpc5121-psc-fifo is required there: -fsl,mpc5121-psc-uart nodes +fsl,mpc512x-psc-uart nodes -------------------------- Required properties : - - compatible : Should contain "fsl,mpc5121-psc-uart" and "fsl,mpc5121-psc" - - cell-index : Index of the PSC in hardware + - compatible : Should contain "fsl,-psc-uart" and "fsl,-psc" + Supported s: mpc5121, mpc5125 - reg : Offset and length of the register set for the PSC device - interrupts : where a is the interrupt number of the PSC FIFO Controller and b is a field that represents an @@ -25,12 +25,21 @@ Recommended properties : - fsl,rx-fifo-size : the size of the RX fifo slice (a multiple of 4) - fsl,tx-fifo-size : the size of the TX fifo slice (a multiple of 4) +PSC in SPI mode +--------------- -fsl,mpc5121-psc-fifo node +Similar to the UART mode a PSC can be operated in SPI mode. The compatible used +for that is fsl,mpc5121-psc-spi. It requires a fsl,mpc5121-psc-fifo as well. +The required and recommended properties are identical to the +fsl,mpc5121-psc-uart nodes, just use spi instead of uart in the compatible +string. + +fsl,mpc512x-psc-fifo node ------------------------- Required properties : - - compatible : Should be "fsl,mpc5121-psc-fifo" + - compatible : Should be "fsl,-psc-fifo" + Supported s: mpc5121, mpc5125 - reg : Offset and length of the register set for the PSC FIFO Controller - interrupts : where a is the interrupt number of the @@ -39,6 +48,9 @@ Required properties : - interrupt-parent : the phandle for the interrupt controller that services interrupts for this device. +Recommended properties : + - clocks : specifies the clock needed to operate the fifo controller + - clock-names : name(s) for the clock(s) listed in clocks Example for a board using PSC0 and PSC1 devices in serial mode: diff --git a/kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc512x_lpbfifo.txt b/kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc512x_lpbfifo.txt new file mode 100644 index 000000000..b3b392fe1 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/powerpc/fsl/mpc512x_lpbfifo.txt @@ -0,0 +1,21 @@ +Freescale MPC512x LocalPlus Bus FIFO (called SCLPC in the Reference Manual) + +Required properties: +- compatible: should be "fsl,mpc512x-lpbfifo"; +- reg: should contain the offset and length of SCLPC register set; +- interrupts: should contain the interrupt specifier for SCLPC; syntax of an + interrupt client node is described in interrupt-controller/interrupts.txt; +- dmas: should contain the DMA specifier for SCLPC as described at + dma/dma.txt and dma/mpc512x-dma.txt; +- dma-names: should be "rx-tx"; + +Example: + + sclpc@10100 { + compatible = "fsl,mpc512x-lpbfifo"; + reg = <0x10100 0x50>; + interrupts = <7 0x8>; + dmas = <&dma0 26>; + dma-names = "rx-tx"; + }; + diff --git a/kernel/Documentation/devicetree/bindings/powerpc/fsl/scfg.txt b/kernel/Documentation/devicetree/bindings/powerpc/fsl/scfg.txt new file mode 100644 index 000000000..0532c46b3 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/powerpc/fsl/scfg.txt @@ -0,0 +1,18 @@ +Freescale Supplement configuration unit (SCFG) + +SCFG is the supplemental configuration unit, that provides SoC specific +configuration and status registers for the chip. Such as getting PEX port +status. + +Required properties: + +- compatible: should be "fsl,-scfg" +- reg: should contain base address and length of SCFG memory-mapped +registers + +Example: + + scfg: global-utilities@fc000 { + compatible = "fsl,t1040-scfg"; + reg = <0xfc000 0x1000>; + }; -- cgit 1.2.3-korg