Add the rt linux 4.1.3-rt3 as base

Import the rt linux 4.1.3-rt3 as OPNFV kvm base.

It's from git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git linux-4.1.y-rt and
the base is:

commit 0917f823c59692d751951bf5ea699a2d1e2f26a2
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date:   Sat Jul 25 12:13:34 2015 +0200

    Prepare v4.1.3-rt3

    Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>

We lose all the git history this way and it's not good. We
should apply another opnfv project repo in future.

Change-Id: I87543d81c9df70d99c5001fbdf646b202c19f423
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>

55 files changed, 2465 insertions, 0 deletions

diff --git a/kernel/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt
new file mode 100644
index 000000000..798cfc9d3
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt
@@ -0,0 +1,74 @@
+GPIO controllers on MPC8xxx SoCs
+
+This is for the non-QE/CPM/GUTs GPIO controllers as found on
+8349, 8572, 8610 and compatible.
+
+Every GPIO controller node must have #gpio-cells property defined,
+this information will be used to translate gpio-specifiers.
+See bindings/gpio/gpio.txt for details of how to specify GPIO
+information for devices.
+
+The GPIO module usually is connected to the SoC's internal interrupt
+controller, see bindings/interrupt-controller/interrupts.txt (the
+interrupt client nodes section) for details how to specify this GPIO
+module's interrupt.
+
+The GPIO module may serve as another interrupt controller (cascaded to
+the SoC's internal interrupt controller).  See the interrupt controller
+nodes section in bindings/interrupt-controller/interrupts.txt for
+details.
+
+Required properties:
+- compatible:		"fsl,<chip>-gpio" followed by "fsl,mpc8349-gpio"
+			for 83xx, "fsl,mpc8572-gpio" for 85xx, or
+			"fsl,mpc8610-gpio" for 86xx.
+- #gpio-cells:		Should be two. The first cell is the pin number
+			and the second cell is used to specify optional
+			parameters (currently unused).
+- interrupt-parent:	Phandle for the interrupt controller that
+			services interrupts for this device.
+- interrupts:		Interrupt mapping for GPIO IRQ.
+- gpio-controller:	Marks the port as GPIO controller.
+
+Optional properties:
+- interrupt-controller:	Empty boolean property which marks the GPIO
+			module as an IRQ controller.
+- #interrupt-cells:	Should be two.  Defines the number of integer
+			cells required to specify an interrupt within
+			this interrupt controller.  The first cell
+			defines the pin number, the second cell
+			defines additional flags (trigger type,
+			trigger polarity).  Note that the available
+			set of trigger conditions supported by the
+			GPIO module depends on the actual SoC.
+
+Example of gpio-controller nodes for a MPC8347 SoC:
+
+	gpio1: gpio-controller@c00 {
+		#gpio-cells = <2>;
+		compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio";
+		reg = <0xc00 0x100>;
+		interrupt-parent = <&ipic>;
+		interrupts = <74 0x8>;
+		gpio-controller;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio2: gpio-controller@d00 {
+		#gpio-cells = <2>;
+		compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio";
+		reg = <0xd00 0x100>;
+		interrupt-parent = <&ipic>;
+		interrupts = <75 0x8>;
+		gpio-controller;
+	};
+
+Example of a peripheral using the GPIO module as an IRQ controller:
+
+	funkyfpga@0 {
+		compatible = "funky-fpga";
+		...
+		interrupt-parent = <&gpio1>;
+		interrupts = <4 3>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt
new file mode 100644
index 000000000..00611acee
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt
@@ -0,0 +1,36 @@
+* Abilis TB10x GPIO controller
+
+Required Properties:
+- compatible: Should be "abilis,tb10x-gpio"
+- reg: Address and length of the register set for the device
+- gpio-controller: Marks the device node as a gpio controller.
+- #gpio-cells: Should be <2>. The first cell is the pin number and the
+  second cell is used to specify optional parameters:
+   - bit 0 specifies polarity (0 for normal, 1 for inverted).
+- abilis,ngpio: the number of GPIO pins this driver controls.
+
+Optional Properties:
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Should be <1>. Interrupts are triggered on both edges.
+- interrupts: Defines the interrupt line connecting this GPIO controller to
+  its parent interrupt controller.
+- interrupt-parent: Defines the parent interrupt controller.
+
+GPIO ranges are specified as described in
+Documentation/devicetree/bindings/gpio/gpio.txt
+
+Example:
+
+	gpioa: gpio@FF140000 {
+		compatible = "abilis,tb10x-gpio";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&tb10x_ictl>;
+		interrupts = <27 2>;
+		reg = <0xFF140000 0x1000>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		abilis,ngpio = <3>;
+		gpio-ranges = <&iomux 0 0 0>;
+		gpio-ranges-group-names = "gpioa_pins";
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt
new file mode 100644
index 000000000..4a63bc96b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt
@@ -0,0 +1,52 @@
+Broadcom Kona Family GPIO
+=========================
+
+This GPIO driver is used in the following Broadcom SoCs:
+  BCM11130, BCM11140, BCM11351, BCM28145, BCM28155
+
+The Broadcom GPIO Controller IP can be configured prior to synthesis to
+support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The
+GPIO controller only supports edge, not level, triggering of interrupts.
+
+Required properties
+-------------------
+
+- compatible: "brcm,bcm11351-gpio", "brcm,kona-gpio"
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The interrupt outputs from the controller. There is one GPIO
+  interrupt per GPIO bank. The number of interrupts listed depends on the
+  number of GPIO banks on the SoC. The interrupts must be ordered by bank,
+  starting with bank 0. There is always a 1:1 mapping between banks and
+  IRQs.
+- #gpio-cells: Should be <2>. The first cell is the pin number, the second
+  cell is used to specify optional parameters:
+  - bit 0 specifies polarity (0 for normal, 1 for inverted)
+  See also "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt.
+- #interrupt-cells: Should be <2>. The first cell is the GPIO number. The
+  second cell is used to specify flags. The following subset of flags is
+  supported:
+  - trigger type (bits[1:0]):
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      3 = low-to-high or high-to-low edge triggered
+      Valid values are 1, 2, 3
+  See also .../devicetree/bindings/interrupt-controller/interrupts.txt.
+- gpio-controller: Marks the device node as a GPIO controller.
+- interrupt-controller: Marks the device node as an interrupt controller.
+
+Example:
+	gpio: gpio@35003000 {
+		compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
+		reg = <0x35003000 0x800>;
+		interrupts =
+		       <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt
new file mode 100644
index 000000000..9d6dcd3fe
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt
@@ -0,0 +1,49 @@
+* General Purpose Input Output (GPIO) bus.
+
+Properties:
+- compatible: "cavium,octeon-3860-gpio"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the GPIO unit's register bank.
+
+- gpio-controller: This is a GPIO controller.
+
+- #gpio-cells: Must be <2>.  The first cell is the GPIO pin.
+
+- interrupt-controller: The GPIO controller is also an interrupt
+  controller, many of its pins may be configured as an interrupt
+  source.
+
+- #interrupt-cells: Must be <2>.  The first cell is the GPIO pin
+   connected to the interrupt source.  The second cell is the interrupt
+   triggering protocol and may have one of four values:
+   1 - edge triggered on the rising edge.
+   2 - edge triggered on the falling edge
+   4 - level triggered active high.
+   8 - level triggered active low.
+
+- interrupts: Interrupt routing for each pin.
+
+Example:
+
+	gpio-controller@1070000000800 {
+		#gpio-cells = <2>;
+		compatible = "cavium,octeon-3860-gpio";
+		reg = <0x10700 0x00000800 0x0 0x100>;
+		gpio-controller;
+		/* Interrupts are specified by two parts:
+		 * 1) GPIO pin number (0..15)
+		 * 2) Triggering (1 - edge rising
+		 *		  2 - edge falling
+		 *		  4 - level active high
+		 *		  8 - level active low)
+		 */
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		/* The GPIO pin connect to 16 consecutive CUI bits */
+		interrupts = <0 16>, <0 17>, <0 18>, <0 19>,
+			     <0 20>, <0 21>, <0 22>, <0 23>,
+			     <0 24>, <0 25>, <0 26>, <0 27>,
+			     <0 28>, <0 29>, <0 30>, <0 31>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt
new file mode 100644
index 000000000..94ae9f82d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt
@@ -0,0 +1,17 @@
+* ARM Cirrus Logic CLPS711X SYSFLG1 MCTRL GPIOs
+
+Required properties:
+- compatible: Should contain "cirrus,clps711x-mctrl-gpio".
+- gpio-controller: Marks the device node as a gpio controller.
+- #gpio-cells: Should be two. The first cell is the pin number and
+  the second cell is used to specify the gpio polarity:
+    0 = Active high,
+    1 = Active low.
+
+Example:
+	sysgpio: sysgpio {
+		compatible = "cirrus,ep7312-mctrl-gpio",
+			     "cirrus,clps711x-mctrl-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt
new file mode 100644
index 000000000..dbd22e0df
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt
@@ -0,0 +1,32 @@
+* Freescale i.MX/MXC GPIO controller
+
+Required properties:
+- compatible : Should be "fsl,<soc>-gpio"
+- reg : Address and length of the register set for the device
+- interrupts : Should be the port interrupt shared by all 32 pins, if
+  one number.  If two numbers, the first one is the interrupt shared
+  by low 16 pins and the second one is for high 16 pins.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify the gpio polarity:
+      0 = active high
+      1 = active low
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells : Should be 2.  The first cell is the GPIO number.
+  The second cell bits[3:0] is used to specify trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+
+Example:
+
+gpio0: gpio@73f84000 {
+	compatible = "fsl,imx51-gpio", "fsl,imx35-gpio";
+	reg = <0x73f84000 0x4000>;
+	interrupts = <50 51>;
+	gpio-controller;
+	#gpio-cells = <2>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/fujitsu,mb86s70-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/fujitsu,mb86s70-gpio.txt
new file mode 100644
index 000000000..bef353f37
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/fujitsu,mb86s70-gpio.txt
@@ -0,0 +1,20 @@
+Fujitsu MB86S7x GPIO Controller
+-------------------------------
+
+Required properties:
+- compatible: Should be "fujitsu,mb86s70-gpio"
+- reg: Base address and length of register space
+- clocks: Specify the clock
+- gpio-controller: Marks the device node as a gpio controller.
+- #gpio-cells: Should be <2>. The first cell is the pin number and the
+  second cell is used to specify optional parameters:
+   - bit 0 specifies polarity (0 for normal, 1 for inverted).
+
+Examples:
+	gpio0: gpio@31000000 {
+		compatible = "fujitsu,mb86s70-gpio";
+		reg = <0 0x31000000 0x10000>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		clocks = <&clk 0 2 1>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-74x164.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-74x164.txt
new file mode 100644
index 000000000..cc2608021
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-74x164.txt
@@ -0,0 +1,22 @@
+* Generic 8-bits shift register GPIO driver
+
+Required properties:
+- compatible : Should be "fairchild,74hc595"
+- reg : chip select number
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify the gpio polarity:
+      0 = active high
+      1 = active low
+- registers-number: Number of daisy-chained shift registers
+
+Example:
+
+gpio5: gpio5@0 {
+	compatible = "fairchild,74hc595";
+	reg = <0>;
+	gpio-controller;
+	#gpio-cells = <2>;
+	registers-number = <4>;
+	spi-max-frequency = <100000>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-74xx-mmio.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-74xx-mmio.txt
new file mode 100644
index 000000000..7bb1a9d60
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-74xx-mmio.txt
@@ -0,0 +1,30 @@
+* 74XX MMIO GPIO driver
+
+Required properties:
+- compatible: Should contain one of the following:
+   "ti,741g125": for 741G125 (1-bit Input),
+   "ti,741g174": for 741G74 (1-bit Output),
+   "ti,742g125": for 742G125 (2-bit Input),
+   "ti,7474"   : for 7474 (2-bit Output),
+   "ti,74125"  : for 74125 (4-bit Input),
+   "ti,74175"  : for 74175 (4-bit Output),
+   "ti,74365"  : for 74365 (6-bit Input),
+   "ti,74174"  : for 74174 (6-bit Output),
+   "ti,74244"  : for 74244 (8-bit Input),
+   "ti,74273"  : for 74273 (8-bit Output),
+   "ti,741624" : for 741624 (16-bit Input),
+   "ti,7416374": for 7416374 (16-bit Output).
+- reg: Physical base address and length where IC resides.
+- gpio-controller: Marks the device node as a gpio controller.
+- #gpio-cells: Should be two. The first cell is the pin number and
+   the second cell is used to specify the GPIO polarity:
+    0 = Active High,
+    1 = Active Low.
+
+Example:
+	ctrl: gpio@30008004 {
+		compatible = "ti,74174";
+		reg = <0x30008004 0x1>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-adnp.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-adnp.txt
new file mode 100644
index 000000000..af66b2724
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-adnp.txt
@@ -0,0 +1,34 @@
+Avionic Design N-bit GPIO expander bindings
+
+Required properties:
+- compatible: should be "ad,gpio-adnp"
+- reg: The I2C slave address for this device.
+- interrupt-parent: phandle of the parent interrupt controller.
+- interrupts: Interrupt specifier for the controllers interrupt.
+- #gpio-cells: Should be 2. The first cell is the GPIO number and the
+  second cell is used to specify optional parameters:
+  - bit 0: polarity (0: normal, 1: inverted)
+- gpio-controller: Marks the device as a GPIO controller
+- nr-gpios: The number of pins supported by the controller.
+
+The GPIO expander can optionally be used as an interrupt controller, in
+which case it uses the default two cell specifier as described in
+Documentation/devicetree/bindings/interrupt-controller/interrupts.txt.
+
+Example:
+
+	gpioext: gpio-controller@41 {
+		compatible = "ad,gpio-adnp";
+		reg = <0x41>;
+
+		interrupt-parent = <&gpio>;
+		interrupts = <160 1>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		nr-gpios = <64>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-altera.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-altera.txt
new file mode 100644
index 000000000..12f50149e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-altera.txt
@@ -0,0 +1,43 @@
+Altera GPIO controller bindings
+
+Required properties:
+- compatible:
+  - "altr,pio-1.0"
+- reg: Physical base address and length of the controller's registers.
+- #gpio-cells : Should be 2
+  - The first cell is the gpio offset number.
+  - The second cell is reserved and is currently unused.
+- gpio-controller : Marks the device node as a GPIO controller.
+- interrupt-controller: Mark the device node as an interrupt controller
+- #interrupt-cells : Should be 1. The interrupt type is fixed in the hardware.
+  - The first cell is the GPIO offset number within the GPIO controller.
+- interrupts: Specify the interrupt.
+- altr,interrupt-trigger: Specifies the interrupt trigger type the GPIO
+  hardware is synthesized. This field is required if the Altera GPIO controller
+  used has IRQ enabled as the interrupt type is not software controlled,
+  but hardware synthesized. Required if GPIO is used as an interrupt
+  controller. The value is defined in <dt-bindings/interrupt-controller/irq.h>
+  Only the following flags are supported:
+    IRQ_TYPE_EDGE_RISING
+    IRQ_TYPE_EDGE_FALLING
+    IRQ_TYPE_EDGE_BOTH
+    IRQ_TYPE_LEVEL_HIGH
+
+Optional properties:
+- altr,ngpio: Width of the GPIO bank. This defines how many pins the
+  GPIO device has. Ranges between 1-32. Optional and defaults to 32 if not
+  specified.
+
+Example:
+
+gpio_altr: gpio@0xff200000 {
+	compatible = "altr,pio-1.0";
+	reg = <0xff200000 0x10>;
+	interrupts = <0 45 4>;
+	altr,ngpio = <32>;
+	altr,interrupt-trigger = <IRQ_TYPE_EDGE_RISING>;
+	#gpio-cells = <2>;
+	gpio-controller;
+	#interrupt-cells = <1>;
+	interrupt-controller;
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt
new file mode 100644
index 000000000..e0d0446a6
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt
@@ -0,0 +1,28 @@
+Cirrus Logic CLPS711X GPIO controller
+
+Required properties:
+- compatible: Should be "cirrus,clps711x-gpio"
+- reg: Physical base GPIO controller registers location and length.
+  There should be two registers, first is DATA register, the second
+  is DIRECTION.
+- gpio-controller: Marks the device node as a gpio controller.
+- #gpio-cells: Should be two. The first cell is the pin number and
+  the second cell is used to specify the gpio polarity:
+    0 = active high
+    1 = active low
+
+Note: Each GPIO port should have an alias correctly numbered in "aliases"
+node.
+
+Example:
+
+aliases {
+	gpio0 = &porta;
+};
+
+porta: gpio@80000000 {
+	compatible = "cirrus,clps711x-gpio";
+	reg = <0x80000000 0x1>, <0x80000040 0x1>;
+	gpio-controller;
+	#gpio-cells = <2>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-davinci.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-davinci.txt
new file mode 100644
index 000000000..5079ba7d6
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-davinci.txt
@@ -0,0 +1,62 @@
+Davinci/Keystone GPIO controller bindings
+
+Required Properties:
+- compatible: should be "ti,dm6441-gpio", "ti,keystone-gpio"
+
+- reg: Physical base address of the controller and the size of memory mapped
+       registers.
+
+- gpio-controller : Marks the device node as a gpio controller.
+
+- #gpio-cells : Should be two.
+  - first cell is the pin number
+  - second cell is used to specify optional parameters (unused)
+
+- interrupt-parent: phandle of the parent interrupt controller.
+
+- interrupts: Array of GPIO interrupt number. Only banked or unbanked IRQs are
+	      supported at a time.
+
+- ti,ngpio: The number of GPIO pins supported.
+
+- ti,davinci-gpio-unbanked: The number of GPIOs that have an individual interrupt
+		             line to processor.
+
+The GPIO controller also acts as an interrupt controller. It uses the default
+two cells specifier as described in Documentation/devicetree/bindings/
+interrupt-controller/interrupts.txt.
+
+Example:
+
+gpio: gpio@1e26000 {
+	compatible = "ti,dm6441-gpio";
+	gpio-controller;
+	#gpio-cells = <2>;
+	reg = <0x226000 0x1000>;
+	interrupt-parent = <&intc>;
+	interrupts = <42 IRQ_TYPE_EDGE_BOTH 43 IRQ_TYPE_EDGE_BOTH
+		44 IRQ_TYPE_EDGE_BOTH 45 IRQ_TYPE_EDGE_BOTH
+		46 IRQ_TYPE_EDGE_BOTH 47 IRQ_TYPE_EDGE_BOTH
+		48 IRQ_TYPE_EDGE_BOTH 49 IRQ_TYPE_EDGE_BOTH
+		50 IRQ_TYPE_EDGE_BOTH>;
+	ti,ngpio = <144>;
+	ti,davinci-gpio-unbanked = <0>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+};
+
+leds {
+	compatible = "gpio-leds";
+
+	led1 {
+		label = "davinci:green:usr1";
+		gpios = <&gpio 10 GPIO_ACTIVE_HIGH>;
+		...
+	};
+
+	led2 {
+		label = "davinci:red:debug1";
+		gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
+		...
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt
new file mode 100644
index 000000000..6c7e6c730
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt
@@ -0,0 +1,39 @@
+Keystone 2 DSP GPIO controller bindings
+
+HOST OS userland running on ARM can send interrupts to DSP cores using
+the DSP GPIO controller IP. It provides 28 IRQ signals per each DSP core.
+This is one of the component used by the IPC mechanism used on Keystone SOCs.
+
+For example TCI6638K2K SoC has 8 DSP GPIO controllers:
+ - 8 for C66x CorePacx CPUs 0-7
+
+Keystone 2 DSP GPIO controller has specific features:
+- each GPIO can be configured only as output pin;
+- setting GPIO value to 1 causes IRQ generation on target DSP core;
+- reading pin value returns 0 - if IRQ was handled or 1 - IRQ is still
+  pending.
+
+Required Properties:
+- compatible: should be "ti,keystone-dsp-gpio"
+- ti,syscon-dev: phandle/offset pair. The phandle to syscon used to
+  access device state control registers and the offset of device's specific
+  registers within device state control registers range.
+- gpio-controller: Marks the device node as a gpio controller.
+- #gpio-cells: Should be 2.
+
+Please refer to gpio.txt in this directory for details of the common GPIO
+bindings used by client devices.
+
+Example:
+	dspgpio0: keystone_dsp_gpio@02620240 {
+		compatible = "ti,keystone-dsp-gpio";
+		ti,syscon-dev = <&devctrl 0x240>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	dsp0: dsp0 {
+		compatible = "linux,rproc-user";
+		...
+		kick-gpio = <&dspgpio0 27>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-fan.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-fan.txt
new file mode 100644
index 000000000..439a7430f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-fan.txt
@@ -0,0 +1,40 @@
+Bindings for fan connected to GPIO lines
+
+Required properties:
+- compatible : "gpio-fan"
+
+Optional properties:
+- gpios: Specifies the pins that map to bits in the control value,
+  ordered MSB-->LSB.
+- gpio-fan,speed-map: A mapping of possible fan RPM speeds and the
+  control value that should be set to achieve them. This array
+  must have the RPM values in ascending order.
+- alarm-gpios: This pin going active indicates something is wrong with
+  the fan, and a udev event will be fired.
+- cooling-cells: If used as a cooling device, must be <2>
+  Also see: Documentation/devicetree/bindings/thermal/thermal.txt
+  min and max states are derived from the speed-map of the fan.
+
+Note: At least one the "gpios" or "alarm-gpios" properties must be set.
+
+Examples:
+
+	gpio_fan {
+		compatible = "gpio-fan";
+		gpios = <&gpio1 14 1
+			 &gpio1 13 1>;
+		gpio-fan,speed-map = <0    0
+				      3000 1
+				      6000 2>;
+		alarm-gpios = <&gpio1 15 1>;
+	};
+	gpio_fan_cool: gpio_fan {
+		compatible = "gpio-fan";
+		gpios = <&gpio2 14 1
+			 &gpio2 13 1>;
+		gpio-fan,speed-map =	<0    0>,
+					<3000 1>,
+					<6000 2>;
+		alarm-gpios = <&gpio2 15 1>;
+		#cooling-cells = <2>; /* min followed by max */
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt
new file mode 100644
index 000000000..e46659810
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt
@@ -0,0 +1,26 @@
+Aeroflex Gaisler GRGPIO General Purpose I/O cores.
+
+The GRGPIO GPIO core is available in the GRLIB VHDL IP core library.
+
+Note: In the ordinary environment for the GRGPIO core, a Leon SPARC system,
+these properties are built from information in the AMBA plug&play.
+
+Required properties:
+
+- name : Should be "GAISLER_GPIO" or "01_01a"
+
+- reg : Address and length of the register set for the device
+
+- interrupts : Interrupt numbers for this device
+
+Optional properties:
+
+- nbits : The number of gpio lines. If not present driver assumes 32 lines.
+
+- irqmap : An array with an index for each gpio line. An index is either a valid
+	index into the interrupts property array, or 0xffffffff that indicates
+	no irq for that line. Driver provides no interrupt support if not
+	present.
+
+For further information look in the documentation for the GLIB IP core library:
+http://www.gaisler.com/products/grlib/grip.pdf
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-lp3943.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-lp3943.txt
new file mode 100644
index 000000000..80fcb7d70
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-lp3943.txt
@@ -0,0 +1,37 @@
+TI/National Semiconductor LP3943 GPIO controller
+
+Required properties:
+  - compatible: "ti,lp3943-gpio"
+  - gpio-controller: Marks the device node as a GPIO controller.
+  - #gpio-cells: Should be 2. See gpio.txt in this directory for a
+                 description of the cells format.
+
+Example:
+Simple LED controls with LP3943 GPIO controller
+
+&i2c4 {
+	lp3943@60 {
+		compatible = "ti,lp3943";
+		reg = <0x60>;
+
+		gpioex: gpio {
+			compatible = "ti,lp3943-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+	};
+};
+
+leds {
+	compatible = "gpio-leds";
+	indicator1 {
+		label = "indi1";
+		gpios = <&gpioex 9 GPIO_ACTIVE_LOW>;
+	};
+
+	indicator2 {
+		label = "indi2";
+		gpios = <&gpioex 10 GPIO_ACTIVE_LOW>;
+		default-state = "off";
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-max732x.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-max732x.txt
new file mode 100644
index 000000000..5fdc843b4
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-max732x.txt
@@ -0,0 +1,59 @@
+* MAX732x-compatible I/O expanders
+
+Required properties:
+  - compatible: Should be one of the following:
+    - "maxim,max7319": For the Maxim MAX7319
+    - "maxim,max7320": For the Maxim MAX7320
+    - "maxim,max7321": For the Maxim MAX7321
+    - "maxim,max7322": For the Maxim MAX7322
+    - "maxim,max7323": For the Maxim MAX7323
+    - "maxim,max7324": For the Maxim MAX7324
+    - "maxim,max7325": For the Maxim MAX7325
+    - "maxim,max7326": For the Maxim MAX7326
+    - "maxim,max7327": For the Maxim MAX7327
+  - reg: I2C slave address for this device.
+  - gpio-controller: Marks the device node as a GPIO controller.
+  - #gpio-cells: Should be 2.
+    - first cell is the GPIO number
+    - second cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>.
+      Only the GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported.
+
+Optional properties:
+
+  The I/O expander can detect input state changes, and thus optionally act as
+  an interrupt controller. When the expander interrupt line is connected all the
+  following properties must be set. For more information please see the
+  interrupt controller device tree bindings documentation available at
+  Documentation/devicetree/bindings/interrupt-controller/interrupts.txt.
+
+  - interrupt-controller: Identifies the node as an interrupt controller.
+  - #interrupt-cells: Number of cells to encode an interrupt source, shall be 2.
+    - first cell is the pin number
+    - second cell is used to specify flags
+  - interrupt-parent: phandle of the parent interrupt controller.
+  - interrupts: Interrupt specifier for the controllers interrupt.
+
+Please refer to gpio.txt in this directory for details of the common GPIO
+bindings used by client devices.
+
+Example 1. MAX7325 with interrupt support enabled (CONFIG_GPIO_MAX732X_IRQ=y):
+
+	expander: max7325@6d {
+		compatible = "maxim,max7325";
+		reg = <0x6d>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+Example 2. MAX7325 with interrupt support disabled (CONFIG_GPIO_MAX732X_IRQ=n):
+
+	expander: max7325@6d {
+		compatible = "maxim,max7325";
+		reg = <0x6d>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
new file mode 100644
index 000000000..f3332b9a8
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
@@ -0,0 +1,85 @@
+Microchip MCP2308/MCP23S08/MCP23017/MCP23S17 driver for
+8-/16-bit I/O expander with serial interface (I2C/SPI)
+
+Required properties:
+- compatible : Should be
+    - "mcp,mcp23s08" (DEPRECATED) for  8 GPIO SPI version
+    - "mcp,mcp23s17" (DEPRECATED) for 16 GPIO SPI version
+    - "mcp,mcp23008" (DEPRECATED) for  8 GPIO I2C version or
+    - "mcp,mcp23017" (DEPRECATED) for 16 GPIO I2C version of the chip
+
+    - "microchip,mcp23s08" for  8 GPIO SPI version
+    - "microchip,mcp23s17" for 16 GPIO SPI version
+    - "microchip,mcp23008" for  8 GPIO I2C version or
+    - "microchip,mcp23017" for 16 GPIO I2C version of the chip
+    NOTE: Do not use the old mcp prefix any more. It is deprecated and will be
+    removed.
+- #gpio-cells : Should be two.
+  - first cell is the pin number
+  - second cell is used to specify flags. Flags are currently unused.
+- gpio-controller : Marks the device node as a GPIO controller.
+- reg : For an address on its bus. I2C uses this a the I2C address of the chip.
+        SPI uses this to specify the chipselect line which the chip is
+        connected to. The driver and the SPI variant of the chip support
+        multiple chips on the same chipselect. Have a look at
+        microchip,spi-present-mask below.
+
+Required device specific properties (only for SPI chips):
+- mcp,spi-present-mask (DEPRECATED)
+- microchip,spi-present-mask : This is a present flag, that makes only sense for SPI
+        chips - as the name suggests. Multiple SPI chips can share the same
+        SPI chipselect. Set a bit in bit0-7 in this mask to 1 if there is a
+        chip connected with the corresponding spi address set. For example if
+        you have a chip with address 3 connected, you have to set bit3 to 1,
+        which is 0x08. mcp23s08 chip variant only supports bits 0-3. It is not
+        possible to mix mcp23s08 and mcp23s17 on the same chipselect. Set at
+        least one bit to 1 for SPI chips.
+    NOTE: Do not use the old mcp prefix any more. It is deprecated and will be
+    removed.
+- spi-max-frequency = The maximum frequency this chip is able to handle
+
+Optional properties:
+- #interrupt-cells : Should be two.
+  - first cell is the pin number
+  - second cell is used to specify flags.
+- interrupt-controller: Marks the device node as a interrupt controller.
+NOTE: The interrupt functionality is only supported for i2c versions of the
+chips. The spi chips can also do the interrupts, but this is not supported by
+the linux driver yet.
+
+Optional device specific properties:
+- microchip,irq-mirror: Sets the mirror flag in the IOCON register. Devices
+        with two interrupt outputs (these are the devices ending with 17 and
+        those that have 16 IOs) have two IO banks: IO 0-7 form bank 1 and
+        IO 8-15 are bank 2. These chips have two different interrupt outputs:
+        One for bank 1 and another for bank 2. If irq-mirror is set, both
+        interrupts are generated regardless of the bank that an input change
+        occurred on. If it is not set, the interrupt are only generated for the
+        bank they belong to.
+        On devices with only one interrupt output this property is useless.
+- microchip,irq-active-high: Sets the INTPOL flag in the IOCON register. This
+        configures the IRQ output polarity as active high.
+
+Example I2C (with interrupt):
+gpiom1: gpio@20 {
+        compatible = "microchip,mcp23017";
+        gpio-controller;
+        #gpio-cells = <2>;
+        reg = <0x20>;
+
+        interrupt-parent = <&gpio1>;
+        interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+        interrupt-controller;
+        #interrupt-cells=<2>;
+        microchip,irq-mirror;
+};
+
+Example SPI:
+gpiom1: gpio@0 {
+        compatible = "microchip,mcp23s17";
+        gpio-controller;
+        #gpio-cells = <2>;
+        spi-present-mask = <0x01>;
+        reg = <0>;
+        spi-max-frequency = <1000000>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt
new file mode 100644
index 000000000..f93d51478
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt
@@ -0,0 +1,38 @@
+Lantiq SoC External Bus memory mapped GPIO controller
+
+By attaching hardware latches to the EBU it is possible to create output
+only gpios. This driver configures a special memory address, which when
+written to outputs 16 bit to the latches.
+
+The node describing the memory mapped GPIOs needs to be a child of the node
+describing the "lantiq,localbus".
+
+Required properties:
+- compatible : Should be "lantiq,gpio-mm-lantiq"
+- reg : Address and length of the register set for the device
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- gpio-controller : Marks the device node as a gpio controller.
+
+Optional properties:
+- lantiq,shadow : The default value that we shall assume as already set on the
+  shift register cascade.
+
+Example:
+
+localbus@0 {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	ranges = <0 0 0x0 0x3ffffff /* addrsel0 */
+		1 0 0x4000000 0x4000010>; /* addsel1 */
+	compatible = "lantiq,localbus", "simple-bus";
+
+	gpio_mm0: gpio@4000000 {
+		compatible = "lantiq,gpio-mm";
+		reg = <1 0x0 0x10>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		lantiq,shadow = <0x77f>
+	};
+}
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-msm.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-msm.txt
new file mode 100644
index 000000000..ac20e68a0
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-msm.txt
@@ -0,0 +1,26 @@
+MSM GPIO controller bindings
+
+Required properties:
+- compatible:
+  - "qcom,msm-gpio" for MSM controllers
+- #gpio-cells : Should be two.
+  - first cell is the pin number
+  - second cell is used to specify optional parameters (unused)
+- gpio-controller : Marks the device node as a GPIO controller.
+- #interrupt-cells : Should be 2.
+- interrupt-controller: Mark the device node as an interrupt controller
+- interrupts : Specify the TLMM summary interrupt number
+- ngpio : Specify the number of MSM GPIOs
+
+Example:
+
+	msmgpio: gpio@fd510000 {
+		compatible = "qcom,msm-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		reg = <0xfd510000 0x4000>;
+		interrupts = <0 208 0>;
+		ngpio = <150>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
new file mode 100644
index 000000000..a6f3bec1d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
@@ -0,0 +1,53 @@
+* Marvell EBU GPIO controller
+
+Required properties:
+
+- compatible : Should be "marvell,orion-gpio", "marvell,mv78200-gpio"
+  or "marvell,armadaxp-gpio". "marvell,orion-gpio" should be used for
+  Orion, Kirkwood, Dove, Discovery (except MV78200) and Armada
+  370. "marvell,mv78200-gpio" should be used for the Discovery
+  MV78200. "marvel,armadaxp-gpio" should be used for all Armada XP
+  SoCs (MV78230, MV78260, MV78460).
+
+- reg: Address and length of the register set for the device. Only one
+  entry is expected, except for the "marvell,armadaxp-gpio" variant
+  for which two entries are expected: one for the general registers,
+  one for the per-cpu registers.
+
+- interrupts: The list of interrupts that are used for all the pins
+  managed by this GPIO bank. There can be more than one interrupt
+  (example: 1 interrupt per 8 pins on Armada XP, which means 4
+  interrupts per bank of 32 GPIOs).
+
+- interrupt-controller: identifies the node as an interrupt controller
+
+- #interrupt-cells: specifies the number of cells needed to encode an
+  interrupt source. Should be two.
+  The first cell is the GPIO number.
+  The second cell is used to specify flags:
+    bits[3:0] trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+
+- gpio-controller: marks the device node as a gpio controller
+
+- ngpios: number of GPIOs this controller has
+
+- #gpio-cells: Should be two. The first cell is the pin number. The
+  second cell is reserved for flags, unused at the moment.
+
+Example:
+
+		gpio0: gpio@d0018100 {
+			compatible = "marvell,armadaxp-gpio";
+			reg = <0xd0018100 0x40>,
+			    <0xd0018800 0x30>;
+			ngpios = <32>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <16>, <17>, <18>, <19>;
+		};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-mxs.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-mxs.txt
new file mode 100644
index 000000000..1e677a47b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-mxs.txt
@@ -0,0 +1,88 @@
+* Freescale MXS GPIO controller
+
+The Freescale MXS GPIO controller is part of MXS PIN controller.  The
+GPIOs are organized in port/bank.  Each port consists of 32 GPIOs.
+
+As the GPIO controller is embedded in the PIN controller and all the
+GPIO ports share the same IO space with PIN controller, the GPIO node
+will be represented as sub-nodes of MXS pinctrl node.
+
+Required properties for GPIO node:
+- compatible : Should be "fsl,<soc>-gpio".  The supported SoCs include
+  imx23 and imx28.
+- interrupts : Should be the port interrupt shared by all 32 pins.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify the gpio polarity:
+      0 = active high
+      1 = active low
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells : Should be 2.  The first cell is the GPIO number.
+  The second cell bits[3:0] is used to specify trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+
+Note: Each GPIO port should have an alias correctly numbered in "aliases"
+node.
+
+Examples:
+
+aliases {
+	gpio0 = &gpio0;
+	gpio1 = &gpio1;
+	gpio2 = &gpio2;
+	gpio3 = &gpio3;
+	gpio4 = &gpio4;
+};
+
+pinctrl@80018000 {
+	compatible = "fsl,imx28-pinctrl", "simple-bus";
+	reg = <0x80018000 2000>;
+
+	gpio0: gpio@0 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <127>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio1: gpio@1 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <126>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio2: gpio@2 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <125>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio3: gpio@3 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <124>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio4: gpio@4 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <123>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-nmk.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-nmk.txt
new file mode 100644
index 000000000..8315ac778
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-nmk.txt
@@ -0,0 +1,31 @@
+Nomadik GPIO controller
+
+Required properties:
+- compatible            : Should be "st,nomadik-gpio".
+- reg                   : Physical base address and length of the controller's registers.
+- interrupts            : The interrupt outputs from the controller.
+- #gpio-cells           : Should be two:
+                            The first cell is the pin number.
+                            The second cell is used to specify optional parameters:
+                              - bits[3:0] trigger type and level flags:
+                                  1 = low-to-high edge triggered.
+                                  2 = high-to-low edge triggered.
+                                  4 = active high level-sensitive.
+                                  8 = active low level-sensitive.
+- gpio-controller       : Marks the device node as a GPIO controller.
+- interrupt-controller  : Marks the device node as an interrupt controller.
+- gpio-bank             : Specifies which bank a controller owns.
+- st,supports-sleepmode : Specifies whether controller can sleep or not
+
+Example:
+
+                gpio1: gpio@8012e080 {
+                        compatible = "st,nomadik-gpio";
+                        reg =  <0x8012e080 0x80>;
+                        interrupts = <0 120 0x4>;
+                        #gpio-cells = <2>;
+                        gpio-controller;
+                        interrupt-controller;
+                        st,supports-sleepmode;
+                        gpio-bank = <1>;
+                };
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-omap.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-omap.txt
new file mode 100644
index 000000000..8d950522e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-omap.txt
@@ -0,0 +1,39 @@
+OMAP GPIO controller bindings
+
+Required properties:
+- compatible:
+  - "ti,omap2-gpio" for OMAP2 controllers
+  - "ti,omap3-gpio" for OMAP3 controllers
+  - "ti,omap4-gpio" for OMAP4 controllers
+- gpio-controller : Marks the device node as a GPIO controller.
+- #gpio-cells : Should be two.
+  - first cell is the pin number
+  - second cell is used to specify optional parameters (unused)
+- interrupt-controller: Mark the device node as an interrupt controller.
+- #interrupt-cells : Should be 2.
+  The first cell is the GPIO number.
+  The second cell is used to specify flags:
+    bits[3:0] trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+
+OMAP specific properties:
+- ti,hwmods:		Name of the hwmod associated to the GPIO:
+			"gpio<X>", <X> being the 1-based instance number
+			from the HW spec.
+- ti,gpio-always-on: 	Indicates if a GPIO bank is always powered and
+			so will never lose its logic state.
+
+
+Example:
+
+gpio4: gpio4 {
+    compatible = "ti,omap4-gpio";
+    ti,hwmods = "gpio4";
+    gpio-controller;
+    #gpio-cells = <2>;
+    interrupt-controller;
+    #interrupt-cells = <2>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-palmas.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-palmas.txt
new file mode 100644
index 000000000..08b5b52a3
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-palmas.txt
@@ -0,0 +1,27 @@
+Palmas GPIO controller bindings
+
+Required properties:
+- compatible:
+  - "ti,palams-gpio" for palma series of the GPIO controller
+  - "ti,tps80036-gpio" for Palma series device TPS80036.
+  - "ti,tps65913-gpio" for palma series device TPS65913.
+  - "ti,tps65914-gpio" for palma series device TPS65914.
+- #gpio-cells : Should be two.
+  - first cell is the gpio pin number
+  - second cell is used to specify the gpio polarity:
+      0 = active high
+      1 = active low
+- gpio-controller : Marks the device node as a GPIO controller.
+
+Note: This gpio node will be sub node of palmas node.
+
+Example:
+	palmas: tps65913@58 {
+		:::::::::::
+		palmas_gpio: palmas_gpio {
+			compatible = "ti,palmas-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+		:::::::::::
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt
new file mode 100644
index 000000000..b9a42f294
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt
@@ -0,0 +1,39 @@
+* NXP PCA953x I2C GPIO multiplexer
+
+Required properties:
+ - compatible: Has to contain one of the following:
+	nxp,pca9505
+	nxp,pca9534
+	nxp,pca9535
+	nxp,pca9536
+	nxp,pca9537
+	nxp,pca9538
+	nxp,pca9539
+	nxp,pca9554
+	nxp,pca9555
+	nxp,pca9556
+	nxp,pca9557
+	nxp,pca9574
+	nxp,pca9575
+	nxp,pca9698
+	maxim,max7310
+	maxim,max7312
+	maxim,max7313
+	maxim,max7315
+	ti,pca6107
+	ti,tca6408
+	ti,tca6416
+	ti,tca6424
+	exar,xra1202
+
+Example:
+
+
+	gpio@20 {
+		compatible = "nxp,pca9505";
+		reg = <0x20>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pca9505>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt
new file mode 100644
index 000000000..ada4e2973
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt
@@ -0,0 +1,71 @@
+* PCF857x-compatible I/O expanders
+
+The PCF857x-compatible chips have "quasi-bidirectional" I/O lines that can be
+driven high by a pull-up current source or driven low to ground. This combines
+the direction and output level into a single bit per line, which can't be read
+back. We can't actually know at initialization time whether a line is configured
+(a) as output and driving the signal low/high, or (b) as input and reporting a
+low/high value, without knowing the last value written since the chip came out
+of reset (if any). The only reliable solution for setting up line direction is
+thus to do it explicitly.
+
+Required Properties:
+
+  - compatible: should be one of the following.
+    - "maxim,max7328": For the Maxim MAX7378
+    - "maxim,max7329": For the Maxim MAX7329
+    - "nxp,pca8574": For the NXP PCA8574
+    - "nxp,pca8575": For the NXP PCA8575
+    - "nxp,pca9670": For the NXP PCA9670
+    - "nxp,pca9671": For the NXP PCA9671
+    - "nxp,pca9672": For the NXP PCA9672
+    - "nxp,pca9673": For the NXP PCA9673
+    - "nxp,pca9674": For the NXP PCA9674
+    - "nxp,pca9675": For the NXP PCA9675
+    - "nxp,pcf8574": For the NXP PCF8574
+    - "nxp,pcf8574a": For the NXP PCF8574A
+    - "nxp,pcf8575": For the NXP PCF8575
+    - "ti,tca9554": For the TI TCA9554
+
+  - reg: I2C slave address.
+
+  - gpio-controller: Marks the device node as a gpio controller.
+  - #gpio-cells: Should be 2. The first cell is the GPIO number and the second
+    cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the
+    GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported.
+
+Optional Properties:
+
+  - lines-initial-states: Bitmask that specifies the initial state of each
+  line. When a bit is set to zero, the corresponding line will be initialized to
+  the input (pulled-up) state. When the  bit is set to one, the line will be
+  initialized the low-level output state. If the property is not specified
+  all lines will be initialized to the input state.
+
+  The I/O expander can detect input state changes, and thus optionally act as
+  an interrupt controller. When the expander interrupt line is connected all the
+  following properties must be set. For more information please see the
+  interrupt controller device tree bindings documentation available at
+  Documentation/devicetree/bindings/interrupt-controller/interrupts.txt.
+
+  - interrupt-controller: Identifies the node as an interrupt controller.
+  - #interrupt-cells: Number of cells to encode an interrupt source, shall be 2.
+  - interrupt-parent: phandle of the parent interrupt controller.
+  - interrupts: Interrupt specifier for the controllers interrupt.
+
+
+Please refer to gpio.txt in this directory for details of the common GPIO
+bindings used by client devices.
+
+Example: PCF8575 I/O expander node
+
+	pcf8575: gpio@20 {
+		compatible = "nxp,pcf8575";
+		reg = <0x20>;
+		interrupt-parent = <&irqpin2>;
+		interrupts = <3 0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt
new file mode 100644
index 000000000..d4eab9227
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt
@@ -0,0 +1,36 @@
+Driver a GPIO line that can be used to turn the power off.
+
+The driver supports both level triggered and edge triggered power off.
+At driver load time, the driver will request the given gpio line and
+install a pm_power_off handler. If the optional properties 'input' is
+not found, the GPIO line will be driven in the inactive
+state. Otherwise its configured as an input.
+
+When the pm_power_off is called, the gpio is configured as an output,
+and drive active, so triggering a level triggered power off
+condition. This will also cause an inactive->active edge condition, so
+triggering positive edge triggered power off. After a delay of 100ms,
+the GPIO is set to inactive, thus causing an active->inactive edge,
+triggering negative edge triggered power off. After another 100ms
+delay the GPIO is driver active again. If the power is still on and
+the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted.
+
+Required properties:
+- compatible : should be "gpio-poweroff".
+- gpios : The GPIO to set high/low, see "gpios property" in
+  Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be
+  low to power down the board set it to "Active Low", otherwise set
+  gpio to "Active High".
+
+Optional properties:
+- input : Initially configure the GPIO line as an input. Only reconfigure
+  it to an output when the pm_power_off function is called. If this optional
+  property is not specified, the GPIO is initialized as an output in its
+  inactive state.
+
+Examples:
+
+gpio-poweroff {
+	compatible = "gpio-poweroff";
+	gpios = <&gpio 4 0>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-restart.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-restart.txt
new file mode 100644
index 000000000..af3701bc1
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-restart.txt
@@ -0,0 +1,54 @@
+Drive a GPIO line that can be used to restart the system from a restart
+handler.
+
+This binding supports level and edge triggered reset.  At driver load
+time, the driver will request the given gpio line and install a restart
+handler. If the optional properties 'open-source' is not found, the GPIO line
+will be driven in the inactive state.  Otherwise its not driven until
+the restart is initiated.
+
+When the system is restarted, the restart handler will be invoked in
+priority order.  The gpio is configured as an output, and driven active,
+triggering a level triggered reset condition. This will also cause an
+inactive->active edge condition, triggering positive edge triggered
+reset. After a delay specified by active-delay, the GPIO is set to
+inactive, thus causing an active->inactive edge, triggering negative edge
+triggered reset. After a delay specified by inactive-delay, the GPIO
+is driven active again.  After a delay specified by wait-delay, the
+restart handler completes allowing other restart handlers to be attempted.
+
+Required properties:
+- compatible : should be "gpio-restart".
+- gpios : The GPIO to set high/low, see "gpios property" in
+  Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be
+  low to reset the board set it to "Active Low", otherwise set
+  gpio to "Active High".
+
+Optional properties:
+- open-source : Treat the GPIO as being open source and defer driving
+  it to when the restart is initiated.  If this optional property is not
+  specified, the GPIO is initialized as an output in its inactive state.
+- priority : A priority ranging from 0 to 255 (default 128) according to
+  the following guidelines:
+	0:	Restart handler of last resort, with limited restart
+		capabilities
+	128:	Default restart handler; use if no other restart handler is
+		expected to be available, and/or if restart functionality is
+		sufficient to restart the entire system
+	255:	Highest priority restart handler, will preempt all other
+		restart handlers
+- active-delay: Delay (default 100) to wait after driving gpio active [ms]
+- inactive-delay: Delay (default 100) to wait after driving gpio inactive [ms]
+- wait-delay: Delay (default 3000) to wait after completing restart
+  sequence [ms]
+
+Examples:
+
+gpio-restart {
+	compatible = "gpio-restart";
+	gpios = <&gpio 4 0>;
+	priority = <128>;
+	active-delay = <100>;
+	inactive-delay = <100>;
+	wait-delay = <3000>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-samsung.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-samsung.txt
new file mode 100644
index 000000000..5375625e8
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-samsung.txt
@@ -0,0 +1,41 @@
+Samsung Exynos4 GPIO Controller
+
+Required properties:
+- compatible: Compatible property value should be "samsung,exynos4-gpio>".
+
+- reg: Physical base address of the controller and length of memory mapped
+  region.
+
+- #gpio-cells: Should be 4. The syntax of the gpio specifier used by client nodes
+  should be the following with values derived from the SoC user manual.
+     <[phandle of the gpio controller node]
+      [pin number within the gpio controller]
+      [mux function]
+      [flags and pull up/down]
+      [drive strength]>
+
+  Values for gpio specifier:
+  - Pin number: is a value between 0 to 7.
+  - Flags and Pull Up/Down: 0 - Pull Up/Down Disabled.
+                            1 - Pull Down Enabled.
+                            3 - Pull Up Enabled.
+          Bit 16 (0x00010000) - Input is active low.
+  - Drive Strength: 0 - 1x,
+                    1 - 3x,
+                    2 - 2x,
+                    3 - 4x
+
+- gpio-controller: Specifies that the node is a gpio controller.
+- #address-cells: should be 1.
+- #size-cells: should be 1.
+
+Example:
+
+	gpa0: gpio-controller@11400000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "samsung,exynos4-gpio";
+		reg = <0x11400000 0x20>;
+		#gpio-cells = <4>;
+		gpio-controller;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-stericsson-coh901.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-stericsson-coh901.txt
new file mode 100644
index 000000000..fd665b44d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-stericsson-coh901.txt
@@ -0,0 +1,7 @@
+ST-Ericsson COH 901 571/3 GPIO controller
+
+Required properties:
+- compatible: Compatible property value should be "stericsson,gpio-coh901"
+- reg: Physical base address of the controller and length of memory mapped
+  region.
+- interrupts: the 0...n interrupts assigned to the different GPIO ports/banks.
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt
new file mode 100644
index 000000000..a0e4cf885
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt
@@ -0,0 +1,18 @@
+STMPE gpio
+----------
+
+Required properties:
+ - compatible: "st,stmpe-gpio"
+
+Optional properties:
+ - st,norequest-mask: bitmask specifying which GPIOs should _not_ be requestable
+   due to different usage (e.g. touch, keypad)
+
+Node name must be stmpe_gpio and should be child node of stmpe node to which it
+belongs.
+
+Example:
+	stmpe_gpio {
+		compatible = "st,stmpe-gpio";
+		st,norequest-mask = <0x20>;	//gpio 5 can't be used
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt
new file mode 100644
index 000000000..854de130a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt
@@ -0,0 +1,42 @@
+Lantiq SoC Serial To Parallel (STP) GPIO controller
+
+The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a
+peripheral controller used to drive external shift register cascades. At most
+3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem
+to drive the 2 LSBs of the cascade automatically.
+
+
+Required properties:
+- compatible : Should be "lantiq,gpio-stp-xway"
+- reg : Address and length of the register set for the device
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- gpio-controller : Marks the device node as a gpio controller.
+
+Optional properties:
+- lantiq,shadow : The default value that we shall assume as already set on the
+  shift register cascade.
+- lantiq,groups : Set the 3 bit mask to select which of the 3 groups are enabled
+  in the shift register cascade.
+- lantiq,dsl : The dsl core can control the 2 LSBs of the gpio cascade. This 2 bit
+  property can enable this feature.
+- lantiq,phy1 : The gphy1 core can control 3 bits of the gpio cascade.
+- lantiq,phy2 : The gphy2 core can control 3 bits of the gpio cascade.
+- lantiq,rising : use rising instead of falling edge for the shift register
+
+Example:
+
+gpio1: stp@E100BB0 {
+	compatible = "lantiq,gpio-stp-xway";
+	reg = <0xE100BB0 0x40>;
+	#gpio-cells = <2>;
+	gpio-controller;
+
+	lantiq,shadow = <0xffff>;
+	lantiq,groups = <0x7>;
+	lantiq,dsl = <0x3>;
+	lantiq,phy1 = <0x7>;
+	lantiq,phy2 = <0x7>;
+	/* lantiq,rising; */
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt
new file mode 100644
index 000000000..ba2bb84ee
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt
@@ -0,0 +1,40 @@
+SEMTECH SX150x GPIO expander bindings
+
+
+Required properties:
+
+- compatible: should be "semtech,sx1506q",
+			"semtech,sx1508q",
+			"semtech,sx1509q".
+
+- reg: The I2C slave address for this device.
+
+- interrupt-parent: phandle of the parent interrupt controller.
+
+- interrupts: Interrupt specifier for the controllers interrupt.
+
+- #gpio-cells: Should be 2. The first cell is the GPIO number and the
+		second cell is used to specify optional parameters:
+		bit 0: polarity (0: normal, 1: inverted)
+
+- gpio-controller: Marks the device as a GPIO controller.
+
+- interrupt-controller: Marks the device as a interrupt controller.
+
+The GPIO expander can optionally be used as an interrupt controller, in
+which case it uses the default two cell specifier as described in
+Documentation/devicetree/bindings/interrupt-controller/interrupts.txt.
+
+Example:
+
+	i2c_gpio_expander@20{
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		compatible = "semtech,sx1506q";
+		reg = <0x20>;
+		interrupt-parent = <&gpio_1>;
+		interrupts = <16 0>;
+
+		gpio-controller;
+		interrupt-controller;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt
new file mode 100644
index 000000000..66788fda1
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt
@@ -0,0 +1,29 @@
+twl4030 GPIO controller bindings
+
+Required properties:
+- compatible:
+  - "ti,twl4030-gpio" for twl4030 GPIO controller
+- #gpio-cells : Should be two.
+  - first cell is the pin number
+  - second cell is used to specify optional parameters (unused)
+- gpio-controller : Marks the device node as a GPIO controller.
+- #interrupt-cells : Should be 2.
+- interrupt-controller: Mark the device node as an interrupt controller
+  The first cell is the GPIO number.
+  The second cell is not used.
+- ti,use-leds : Enables LEDA and LEDB outputs if set
+- ti,debounce : if n-th bit is set, debounces GPIO-n
+- ti,mmc-cd : if n-th bit is set, GPIO-n controls VMMC(n+1)
+- ti,pullups : if n-th bit is set, set a pullup on GPIO-n
+- ti,pulldowns : if n-th bit is set, set a pulldown on GPIO-n
+
+Example:
+
+twl_gpio: gpio {
+    compatible = "ti,twl4030-gpio";
+    #gpio-cells = <2>;
+    gpio-controller;
+    #interrupt-cells = <2>;
+    interrupt-controller;
+    ti,use-leds;
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-tz1090-pdc.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-tz1090-pdc.txt
new file mode 100644
index 000000000..1fd98ffa8
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-tz1090-pdc.txt
@@ -0,0 +1,45 @@
+ImgTec TZ1090 PDC GPIO Controller
+
+Required properties:
+- compatible: Compatible property value should be "img,tz1090-pdc-gpio".
+
+- reg: Physical base address of the controller and length of memory mapped
+  region. This starts at and cover the SOC_GPIO_CONTROL registers.
+
+- gpio-controller: Specifies that the node is a gpio controller.
+
+- #gpio-cells: Should be 2. The syntax of the gpio specifier used by client
+  nodes should have the following values.
+     <[phandle of the gpio controller node]
+      [PDC gpio number]
+      [gpio flags]>
+
+  Values for gpio specifier:
+  - GPIO number: a value in the range 0 to 6.
+  - GPIO flags: bit field of flags, as defined in <dt-bindings/gpio/gpio.h>.
+    Only the following flags are supported:
+      GPIO_ACTIVE_HIGH
+      GPIO_ACTIVE_LOW
+
+Optional properties:
+- gpio-ranges: Mapping to pin controller pins (as described in
+  Documentation/devicetree/bindings/gpio/gpio.txt)
+
+- interrupts: Individual syswake interrupts (other GPIOs cannot interrupt)
+
+
+Example:
+
+	pdc_gpios: gpio-controller@02006500 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		compatible = "img,tz1090-pdc-gpio";
+		reg = <0x02006500 0x100>;
+
+		interrupt-parent = <&pdc>;
+		interrupts =	<8  IRQ_TYPE_NONE>,	/* Syswake 0 */
+				<9  IRQ_TYPE_NONE>,	/* Syswake 1 */
+				<10 IRQ_TYPE_NONE>;	/* Syswake 2 */
+		gpio-ranges = <&pdc_pinctrl 0 0 7>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-tz1090.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-tz1090.txt
new file mode 100644
index 000000000..174cdf309
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-tz1090.txt
@@ -0,0 +1,88 @@
+ImgTec TZ1090 GPIO Controller
+
+Required properties:
+- compatible: Compatible property value should be "img,tz1090-gpio".
+
+- reg: Physical base address of the controller and length of memory mapped
+  region.
+
+- #address-cells: Should be 1 (for bank subnodes)
+
+- #size-cells: Should be 0 (for bank subnodes)
+
+- Each bank of GPIOs should have a subnode to represent it.
+
+  Bank subnode required properties:
+  - reg: Index of bank in the range 0 to 2.
+
+  - gpio-controller: Specifies that the node is a gpio controller.
+
+  - #gpio-cells: Should be 2. The syntax of the gpio specifier used by client
+    nodes should have the following values.
+       <[phandle of the gpio controller node]
+        [gpio number within the gpio bank]
+        [gpio flags]>
+
+    Values for gpio specifier:
+    - GPIO number: a value in the range 0 to 29.
+    - GPIO flags: bit field of flags, as defined in <dt-bindings/gpio/gpio.h>.
+      Only the following flags are supported:
+        GPIO_ACTIVE_HIGH
+        GPIO_ACTIVE_LOW
+
+  Bank subnode optional properties:
+  - gpio-ranges: Mapping to pin controller pins (as described in
+    Documentation/devicetree/bindings/gpio/gpio.txt)
+
+  - interrupts: Interrupt for the entire bank
+
+  - interrupt-controller: Specifies that the node is an interrupt controller
+
+  - #interrupt-cells: Should be 2. The syntax of the interrupt specifier used by
+    client nodes should have the following values.
+       <[phandle of the interurupt controller]
+        [gpio number within the gpio bank]
+        [irq flags]>
+
+    Values for irq specifier:
+    - GPIO number: a value in the range 0 to 29
+    - IRQ flags: value to describe edge and level triggering, as defined in
+      <dt-bindings/interrupt-controller/irq.h>. Only the following flags are
+      supported:
+        IRQ_TYPE_EDGE_RISING
+        IRQ_TYPE_EDGE_FALLING
+        IRQ_TYPE_EDGE_BOTH
+        IRQ_TYPE_LEVEL_HIGH
+        IRQ_TYPE_LEVEL_LOW
+
+
+
+Example:
+
+	gpios: gpio-controller@02005800 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "img,tz1090-gpio";
+		reg = <0x02005800 0x90>;
+
+		/* bank 0 with an interrupt */
+		gpios0: bank@0 {
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			reg = <0>;
+			interrupts = <13 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 30>;
+			interrupt-controller;
+		};
+
+		/* bank 2 without interrupt */
+		gpios2: bank@2 {
+			#gpio-cells = <2>;
+			reg = <2>;
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 60 30>;
+		};
+	};
+
+
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-vf610.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-vf610.txt
new file mode 100644
index 000000000..436cc99c6
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-vf610.txt
@@ -0,0 +1,55 @@
+* Freescale VF610 PORT/GPIO module
+
+The Freescale PORT/GPIO modules are two adjacent modules providing GPIO
+functionality. Each pair serves 32 GPIOs. The VF610 has 5 instances of
+each, and each PORT module has its own interrupt.
+
+Required properties for GPIO node:
+- compatible : Should be "fsl,<soc>-gpio", currently "fsl,vf610-gpio"
+- reg : The first reg tuple represents the PORT module, the second tuple
+  the GPIO module.
+- interrupts : Should be the port interrupt shared by all 32 pins.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be two. The first cell is the pin number and
+  the second cell is used to specify the gpio polarity:
+      0 = active high
+      1 = active low
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells : Should be 2.  The first cell is the GPIO number.
+  The second cell bits[3:0] is used to specify trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+
+Note: Each GPIO port should have an alias correctly numbered in "aliases"
+node.
+
+Examples:
+
+aliases {
+	gpio0 = &gpio1;
+	gpio1 = &gpio2;
+};
+
+gpio1: gpio@40049000 {
+	compatible = "fsl,vf610-gpio";
+	reg = <0x40049000 0x1000 0x400ff000 0x40>;
+	interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>;
+	gpio-controller;
+	#gpio-cells = <2>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+	gpio-ranges = <&iomuxc 0 0 32>;
+};
+
+gpio2: gpio@4004a000 {
+	compatible = "fsl,vf610-gpio";
+	reg = <0x4004a000 0x1000 0x400ff040 0x40>;
+	interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
+	gpio-controller;
+	#gpio-cells = <2>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+	gpio-ranges = <&iomuxc 0 32 32>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt
new file mode 100644
index 000000000..dae130060
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt
@@ -0,0 +1,32 @@
+APM X-Gene Standby GPIO controller bindings
+
+This is a gpio controller in the standby domain.
+
+There are 20 GPIO pins from 0..21. There is no GPIO_DS14 or GPIO_DS15,
+only GPIO_DS8..GPIO_DS13 support interrupts. The IRQ mapping
+is currently 1-to-1 on interrupts 0x28 thru 0x2d.
+
+Required properties:
+- compatible: "apm,xgene-gpio-sb" for the X-Gene Standby GPIO controller
+- reg: Physical base address and size of the controller's registers
+- #gpio-cells: Should be two.
+	- first cell is the pin number
+	- second cell is used to specify the gpio polarity:
+		0 = active high
+		1 = active low
+- gpio-controller: Marks the device node as a GPIO controller.
+- interrupts: Shall contain exactly 6 interrupts.
+
+Example:
+	sbgpio: sbgpio@17001000 {
+		compatible = "apm,xgene-gpio-sb";
+		reg = <0x0 0x17001000 0x0 0x400>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupts = 	<0x0 0x28 0x1>,
+				<0x0 0x29 0x1>,
+				<0x0 0x2a 0x1>,
+				<0x0 0x2b 0x1>,
+				<0x0 0x2c 0x1>,
+				<0x0 0x2d 0x1>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-xgene.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-xgene.txt
new file mode 100644
index 000000000..86dbb05e7
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-xgene.txt
@@ -0,0 +1,22 @@
+APM X-Gene SoC GPIO controller bindings
+
+This is a gpio controller that is part of the flash controller.
+This gpio controller controls a total of 48 gpios.
+
+Required properties:
+- compatible: "apm,xgene-gpio" for X-Gene GPIO controller
+- reg: Physical base address and size of the controller's registers
+- #gpio-cells: Should be two.
+	- first cell is the pin number
+	- second cell is used to specify the gpio polarity:
+		0 = active high
+		1 = active low
+- gpio-controller: Marks the device node as a GPIO controller.
+
+Example:
+	gpio0: gpio0@1701c000 {
+		compatible = "apm,xgene-gpio";
+		reg = <0x0 0x1701c000 0x0 0x40>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt
new file mode 100644
index 000000000..63bf4becd
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt
@@ -0,0 +1,48 @@
+Xilinx plb/axi GPIO controller
+
+Dual channel GPIO controller with configurable number of pins
+(from 1 to 32 per channel). Every pin can be configured as
+input/output/tristate. Both channels share the same global IRQ but
+local interrupts can be enabled on channel basis.
+
+Required properties:
+- compatible : Should be "xlnx,xps-gpio-1.00.a"
+- reg : Address and length of the register set for the device
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional parameters (currently unused).
+- gpio-controller : Marks the device node as a GPIO controller.
+
+Optional properties:
+- interrupts : Interrupt mapping for GPIO IRQ.
+- interrupt-parent : Phandle for the interrupt controller that
+  services interrupts for this device.
+- xlnx,all-inputs : if n-th bit is setup, GPIO-n is input
+- xlnx,dout-default : if n-th bit is 1, GPIO-n default value is 1
+- xlnx,gpio-width : gpio width
+- xlnx,tri-default : if n-th bit is 1, GPIO-n is in tristate mode
+- xlnx,is-dual : if 1, controller also uses the second channel
+- xlnx,all-inputs-2 : as above but for the second channel
+- xlnx,dout-default-2 : as above but the second channel
+- xlnx,gpio2-width : as above but for the second channel
+- xlnx,tri-default-2 : as above but for the second channel
+
+
+Example:
+gpio: gpio@40000000 {
+	#gpio-cells = <2>;
+	compatible = "xlnx,xps-gpio-1.00.a";
+	gpio-controller ;
+	interrupt-parent = <&microblaze_0_intc>;
+	interrupts = < 6 2 >;
+	reg = < 0x40000000 0x10000 >;
+	xlnx,all-inputs = <0x0>;
+	xlnx,all-inputs-2 = <0x0>;
+	xlnx,dout-default = <0x0>;
+	xlnx,dout-default-2 = <0x0>;
+	xlnx,gpio-width = <0x2>;
+	xlnx,gpio2-width = <0x2>;
+	xlnx,interrupt-present = <0x1>;
+	xlnx,is-dual = <0x1>;
+	xlnx,tri-default = <0xffffffff>;
+	xlnx,tri-default-2 = <0xffffffff>;
+} ;
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-zevio.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-zevio.txt
new file mode 100644
index 000000000..a37bd9ae2
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-zevio.txt
@@ -0,0 +1,16 @@
+Zevio GPIO controller
+
+Required properties:
+- compatible: Should be "lsi,zevio-gpio"
+- reg: Address and length of the register set for the device
+- #gpio-cells: Should be two. The first cell is the pin number and the
+  second cell is used to specify optional parameters (currently unused).
+- gpio-controller: Marks the device node as a GPIO controller.
+
+Example:
+	gpio: gpio@90000000 {
+		compatible = "lsi,zevio-gpio";
+		reg = <0x90000000 0x1000>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-zynq.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-zynq.txt
new file mode 100644
index 000000000..986371a4b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-zynq.txt
@@ -0,0 +1,26 @@
+Xilinx Zynq GPIO controller Device Tree Bindings
+-------------------------------------------
+
+Required properties:
+- #gpio-cells 		: Should be two
+			  - First cell is the GPIO line number
+			  - Second cell is used to specify optional
+			    parameters (unused)
+- compatible		: Should be "xlnx,zynq-gpio-1.0"
+- clocks		: Clock specifier (see clock bindings for details)
+- gpio-controller	: Marks the device node as a GPIO controller.
+- interrupts		: Interrupt specifier (see interrupt bindings for
+			  details)
+- interrupt-parent	: Must be core interrupt controller
+- reg			: Address and length of the register set for the device
+
+Example:
+	gpio@e000a000 {
+		#gpio-cells = <2>;
+		compatible = "xlnx,zynq-gpio-1.0";
+		clocks = <&clkc 42>;
+		gpio-controller;
+		interrupt-parent = <&intc>;
+		interrupts = <0 20 4>;
+		reg = <0xe000a000 0x1000>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio.txt
new file mode 100644
index 000000000..5788d5cf1
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio.txt
@@ -0,0 +1,242 @@
+Specifying GPIO information for devices
+============================================
+
+1) gpios property
+-----------------
+
+Nodes that makes use of GPIOs should specify them using one or more
+properties, each containing a 'gpio-list':
+
+	gpio-list ::= <single-gpio> [gpio-list]
+	single-gpio ::= <gpio-phandle> <gpio-specifier>
+	gpio-phandle : phandle to gpio controller node
+	gpio-specifier : Array of #gpio-cells specifying specific gpio
+			 (controller specific)
+
+GPIO properties should be named "[<name>-]gpios", with <name> being the purpose
+of this GPIO for the device. While a non-existent <name> is considered valid
+for compatibility reasons (resolving to the "gpios" property), it is not allowed
+for new bindings.
+
+GPIO properties can contain one or more GPIO phandles, but only in exceptional
+cases should they contain more than one. If your device uses several GPIOs with
+distinct functions, reference each of them under its own property, giving it a
+meaningful name. The only case where an array of GPIOs is accepted is when
+several GPIOs serve the same function (e.g. a parallel data line).
+
+The exact purpose of each gpios property must be documented in the device tree
+binding of the device.
+
+The following example could be used to describe GPIO pins used as device enable
+and bit-banged data signals:
+
+	gpio1: gpio1 {
+		gpio-controller
+		 #gpio-cells = <2>;
+	};
+	gpio2: gpio2 {
+		gpio-controller
+		 #gpio-cells = <1>;
+	};
+	[...]
+
+	enable-gpios = <&gpio2 2>;
+	data-gpios = <&gpio1 12 0>,
+		     <&gpio1 13 0>,
+		     <&gpio1 14 0>,
+		     <&gpio1 15 0>;
+
+Note that gpio-specifier length is controller dependent.  In the
+above example, &gpio1 uses 2 cells to specify a gpio, while &gpio2
+only uses one.
+
+gpio-specifier may encode: bank, pin position inside the bank,
+whether pin is open-drain and whether pin is logically inverted.
+Exact meaning of each specifier cell is controller specific, and must
+be documented in the device tree binding for the device. Use the macros
+defined in include/dt-bindings/gpio/gpio.h whenever possible:
+
+Example of a node using GPIOs:
+
+	node {
+		enable-gpios = <&qe_pio_e 18 GPIO_ACTIVE_HIGH>;
+	};
+
+GPIO_ACTIVE_HIGH is 0, so in this example gpio-specifier is "18 0" and encodes
+GPIO pin number, and GPIO flags as accepted by the "qe_pio_e" gpio-controller.
+
+1.1) GPIO specifier best practices
+----------------------------------
+
+A gpio-specifier should contain a flag indicating the GPIO polarity; active-
+high or active-low. If it does, the following best practices should be
+followed:
+
+The gpio-specifier's polarity flag should represent the physical level at the
+GPIO controller that achieves (or represents, for inputs) a logically asserted
+value at the device. The exact definition of logically asserted should be
+defined by the binding for the device. If the board inverts the signal between
+the GPIO controller and the device, then the gpio-specifier will represent the
+opposite physical level than the signal at the device's pin.
+
+When the device's signal polarity is configurable, the binding for the
+device must either:
+
+a) Define a single static polarity for the signal, with the expectation that
+any software using that binding would statically program the device to use
+that signal polarity.
+
+The static choice of polarity may be either:
+
+a1) (Preferred) Dictated by a binding-specific DT property.
+
+or:
+
+a2) Defined statically by the DT binding itself.
+
+In particular, the polarity cannot be derived from the gpio-specifier, since
+that would prevent the DT from separately representing the two orthogonal
+concepts of configurable signal polarity in the device, and possible board-
+level signal inversion.
+
+or:
+
+b) Pick a single option for device signal polarity, and document this choice
+in the binding. The gpio-specifier should represent the polarity of the signal
+(at the GPIO controller) assuming that the device is configured for this
+particular signal polarity choice. If software chooses to program the device
+to generate or receive a signal of the opposite polarity, software will be
+responsible for correctly interpreting (inverting) the GPIO signal at the GPIO
+controller.
+
+2) gpio-controller nodes
+------------------------
+
+Every GPIO controller node must contain both an empty "gpio-controller"
+property, and a #gpio-cells integer property, which indicates the number of
+cells in a gpio-specifier.
+
+The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism
+providing automatic GPIO request and configuration as part of the
+gpio-controller's driver probe function.
+
+Each GPIO hog definition is represented as a child node of the GPIO controller.
+Required properties:
+- gpio-hog:   A property specifying that this child node represent a GPIO hog.
+- gpios:      Store the GPIO information (id, flags, ...). Shall contain the
+	      number of cells specified in its parent node (GPIO controller
+	      node).
+Only one of the following properties scanned in the order shown below.
+This means that when multiple properties are present they will be searched
+in the order presented below and the first match is taken as the intended
+configuration.
+- input:      A property specifying to set the GPIO direction as input.
+- output-low  A property specifying to set the GPIO direction as output with
+	      the value low.
+- output-high A property specifying to set the GPIO direction as output with
+	      the value high.
+
+Optional properties:
+- line-name:  The GPIO label name. If not present the node name is used.
+
+Example of two SOC GPIO banks defined as gpio-controller nodes:
+
+	qe_pio_a: gpio-controller@1400 {
+		compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank";
+		reg = <0x1400 0x18>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		line_b {
+			gpio-hog;
+			gpios = <6 0>;
+			output-low;
+			line-name = "foo-bar-gpio";
+		};
+	};
+
+	qe_pio_e: gpio-controller@1460 {
+		compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank";
+		reg = <0x1460 0x18>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+2.1) gpio- and pin-controller interaction
+-----------------------------------------
+
+Some or all of the GPIOs provided by a GPIO controller may be routed to pins
+on the package via a pin controller. This allows muxing those pins between
+GPIO and other functions.
+
+It is useful to represent which GPIOs correspond to which pins on which pin
+controllers. The gpio-ranges property described below represents this, and
+contains information structures as follows:
+
+	gpio-range-list ::= <single-gpio-range> [gpio-range-list]
+	single-gpio-range ::= <numeric-gpio-range> | <named-gpio-range>
+	numeric-gpio-range ::=
+			<pinctrl-phandle> <gpio-base> <pinctrl-base> <count>
+	named-gpio-range ::= <pinctrl-phandle> <gpio-base> '<0 0>'
+	pinctrl-phandle : phandle to pin controller node
+	gpio-base : Base GPIO ID in the GPIO controller
+	pinctrl-base : Base pinctrl pin ID in the pin controller
+	count : The number of GPIOs/pins in this range
+
+The "pin controller node" mentioned above must conform to the bindings
+described in ../pinctrl/pinctrl-bindings.txt.
+
+In case named gpio ranges are used (ranges with both <pinctrl-base> and
+<count> set to 0), the property gpio-ranges-group-names contains one string
+for every single-gpio-range in gpio-ranges:
+	gpiorange-names-list ::= <gpiorange-name> [gpiorange-names-list]
+	gpiorange-name : Name of the pingroup associated to the GPIO range in
+			the respective pin controller.
+
+Elements of gpiorange-names-list corresponding to numeric ranges contain
+the empty string. Elements of gpiorange-names-list corresponding to named
+ranges contain the name of a pin group defined in the respective pin
+controller. The number of pins/GPIOs in the range is the number of pins in
+that pin group.
+
+Previous versions of this binding required all pin controller nodes that
+were referenced by any gpio-ranges property to contain a property named
+#gpio-range-cells with value <3>. This requirement is now deprecated.
+However, that property may still exist in older device trees for
+compatibility reasons, and would still be required even in new device
+trees that need to be compatible with older software.
+
+Example 1:
+
+	qe_pio_e: gpio-controller@1460 {
+		#gpio-cells = <2>;
+		compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank";
+		reg = <0x1460 0x18>;
+		gpio-controller;
+		gpio-ranges = <&pinctrl1 0 20 10>, <&pinctrl2 10 50 20>;
+	};
+
+Here, a single GPIO controller has GPIOs 0..9 routed to pin controller
+pinctrl1's pins 20..29, and GPIOs 10..19 routed to pin controller pinctrl2's
+pins 50..59.
+
+Example 2:
+
+	gpio_pio_i: gpio-controller@14B0 {
+		#gpio-cells = <2>;
+		compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank";
+		reg = <0x1480 0x18>;
+		gpio-controller;
+		gpio-ranges =			<&pinctrl1 0 20 10>,
+						<&pinctrl2 10 0 0>,
+						<&pinctrl1 15 0 10>,
+						<&pinctrl2 25 0 0>;
+		gpio-ranges-group-names =	"",
+						"foo",
+						"",
+						"bar";
+	};
+
+Here, three GPIO ranges are defined wrt. two pin controllers. pinctrl1 GPIO
+ranges are defined using pin numbers whereas the GPIO ranges wrt. pinctrl2
+are named "foo" and "bar".
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio_atmel.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio_atmel.txt
new file mode 100644
index 000000000..85f8c0d08
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio_atmel.txt
@@ -0,0 +1,25 @@
+* Atmel GPIO controller (PIO)
+
+Required properties:
+- compatible: "atmel,<chip>-gpio", where <chip> is at91rm9200 or at91sam9x5.
+- reg: Should contain GPIO controller registers location and length
+- interrupts: Should be the port interrupt shared by all the pins.
+- #gpio-cells: Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- gpio-controller: Marks the device node as a GPIO controller.
+
+optional properties:
+- #gpio-lines: Number of gpio if absent 32.
+
+
+Example:
+	pioA: gpio@fffff200 {
+		compatible = "atmel,at91rm9200-gpio";
+		reg = <0xfffff200 0x100>;
+		interrupts = <2 4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		#gpio-lines = <19>;
+	};
+
diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt
new file mode 100644
index 000000000..49819367a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt
@@ -0,0 +1,43 @@
+NXP LPC32xx SoC GPIO controller
+
+Required properties:
+- compatible: must be "nxp,lpc3220-gpio"
+- reg: Physical base address and length of the controller's registers.
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells: Should be 3:
+   1) bank:
+      0: GPIO P0
+      1: GPIO P1
+      2: GPIO P2
+      3: GPIO P3
+      4: GPI P3
+      5: GPO P3
+   2) pin number
+   3) optional parameters:
+      - bit 0 specifies polarity (0 for normal, 1 for inverted)
+- reg: Index of the GPIO group
+
+Example:
+
+	gpio: gpio@40028000 {
+		compatible = "nxp,lpc3220-gpio";
+		reg = <0x40028000 0x1000>;
+		gpio-controller;
+		#gpio-cells = <3>; /* bank, pin, flags */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led0 {
+			gpios = <&gpio 5 1 1>; /* GPO_P3 1, active low */
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led1 {
+			gpios = <&gpio 5 14 1>; /* GPO_P3 14, active low */
+			linux,default-trigger = "timer";
+			default-state = "off";
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/moxa,moxart-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/moxa,moxart-gpio.txt
new file mode 100644
index 000000000..f8e8f185a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/moxa,moxart-gpio.txt
@@ -0,0 +1,19 @@
+MOXA ART GPIO Controller
+
+Required properties:
+
+- #gpio-cells : Should be 2, The first cell is the pin number,
+		the second cell is used to specify polarity:
+			0 = active high
+			1 = active low
+- compatible : Must be "moxa,moxart-gpio"
+- reg : Should contain registers location and length
+
+Example:
+
+	gpio: gpio@98700000 {
+		gpio-controller;
+		#gpio-cells = <2>;
+		compatible = "moxa,moxart-gpio";
+		reg =	<0x98700000 0xC>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt
new file mode 100644
index 000000000..98d198396
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt
@@ -0,0 +1,69 @@
+* Marvell PXA GPIO controller
+
+Required properties:
+- compatible : Should be "intel,pxa25x-gpio", "intel,pxa26x-gpio",
+		"intel,pxa27x-gpio", "intel,pxa3xx-gpio",
+		"marvell,pxa93x-gpio", "marvell,mmp-gpio",
+		"marvell,mmp2-gpio" or marvell,pxa1928-gpio.
+- reg : Address and length of the register set for the device
+- interrupts : Should be the port interrupt shared by all gpio pins.
+  There're three gpio interrupts in arch-pxa, and they're gpio0,
+  gpio1 and gpio_mux. There're only one gpio interrupt in arch-mmp,
+  gpio_mux.
+- interrupt-names : Should be the names of irq resources. Each interrupt
+  uses its own interrupt name, so there should be as many interrupt names
+  as referenced interrupts.
+- interrupt-controller : Identifies the node as an interrupt controller.
+- #interrupt-cells: Specifies the number of cells needed to encode an
+  interrupt source.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be one.  It is the pin number.
+
+Example for a MMP platform:
+
+	gpio: gpio@d4019000 {
+		compatible = "marvell,mmp-gpio";
+		reg = <0xd4019000 0x1000>;
+		interrupts = <49>;
+		interrupt-names = "gpio_mux";
+		gpio-controller;
+		#gpio-cells = <1>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+      };
+
+Example for a PXA3xx platform:
+
+	gpio: gpio@40e00000 {
+		compatible = "intel,pxa3xx-gpio";
+		reg = <0x40e00000 0x10000>;
+		interrupt-names = "gpio0", "gpio1", "gpio_mux";
+		interrupts = <8 9 10>;
+		gpio-controller;
+		#gpio-cells = <0x2>;
+		interrupt-controller;
+		#interrupt-cells = <0x2>;
+	};
+
+* Marvell Orion GPIO Controller
+
+Required properties:
+- compatible         : Should be "marvell,orion-gpio"
+- reg                : Address and length of the register set for controller.
+- gpio-controller    : So we know this is a gpio controller.
+- ngpio              : How many gpios this controller has.
+- interrupts	     : Up to 4 Interrupts for the controller.
+
+Optional properties:
+- mask-offset        : For SMP Orions, offset for Nth CPU
+
+Example:
+
+		gpio0: gpio@10100 {
+			compatible = "marvell,orion-gpio";
+			#gpio-cells = <2>;
+			gpio-controller;
+			reg = <0x10100 0x40>;
+			ngpio = <32>;
+			interrupts = <35>, <36>, <37>, <38>;
+		};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.txt
new file mode 100644
index 000000000..023c9526e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.txt
@@ -0,0 +1,40 @@
+NVIDIA Tegra GPIO controller
+
+Required properties:
+- compatible : "nvidia,tegra<chip>-gpio"
+- reg : Physical base address and length of the controller's registers.
+- interrupts : The interrupt outputs from the controller. For Tegra20,
+  there should be 7 interrupts specified, and for Tegra30, there should
+  be 8 interrupts specified.
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional parameters:
+  - bit 0 specifies polarity (0 for normal, 1 for inverted)
+- gpio-controller : Marks the device node as a GPIO controller.
+- #interrupt-cells : Should be 2.
+  The first cell is the GPIO number.
+  The second cell is used to specify flags:
+    bits[3:0] trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+      Valid combinations are 1, 2, 3, 4, 8.
+- interrupt-controller : Marks the device node as an interrupt controller.
+
+Example:
+
+gpio: gpio@6000d000 {
+	compatible = "nvidia,tegra20-gpio";
+	reg = < 0x6000d000 0x1000 >;
+	interrupts = < 0 32 0x04
+		       0 33 0x04
+		       0 34 0x04
+		       0 35 0x04
+		       0 55 0x04
+		       0 87 0x04
+		       0 89 0x04 >;
+	#gpio-cells = <2>;
+	gpio-controller;
+	#interrupt-cells = <2>;
+	interrupt-controller;
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/pl061-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/pl061-gpio.txt
new file mode 100644
index 000000000..89058d375
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/pl061-gpio.txt
@@ -0,0 +1,10 @@
+ARM PL061 GPIO controller
+
+Required properties:
+- compatible : "arm,pl061", "arm,primecell"
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional parameters:
+  - bit 0 specifies polarity (0 for normal, 1 for inverted)
+- gpio-controller : Marks the device node as a GPIO controller.
+- interrupts : Interrupt mapping for GPIO IRQ.
+- gpio-ranges : Interaction with the PINCTRL subsystem.
diff --git a/kernel/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/kernel/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt
new file mode 100644
index 000000000..38fb86f28
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt
@@ -0,0 +1,63 @@
+* Renesas R-Car GPIO Controller
+
+Required Properties:
+
+  - compatible: should contain one of the following.
+    - "renesas,gpio-r8a7778": for R8A7778 (R-Mobile M1) compatible GPIO controller.
+    - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller.
+    - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller.
+    - "renesas,gpio-r8a7791": for R8A7791 (R-Car M2-W) compatible GPIO controller.
+    - "renesas,gpio-r8a7793": for R8A7793 (R-Car M2-N) compatible GPIO controller.
+    - "renesas,gpio-r8a7794": for R8A7794 (R-Car E2) compatible GPIO controller.
+    - "renesas,gpio-rcar": for generic R-Car GPIO controller.
+
+  - reg: Base address and length of each memory resource used by the GPIO
+    controller hardware module.
+
+  - interrupt-parent: phandle of the parent interrupt controller.
+  - interrupts: Interrupt specifier for the controllers interrupt.
+
+  - gpio-controller: Marks the device node as a gpio controller.
+  - #gpio-cells: Should be 2. The first cell is the GPIO number and the second
+    cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the
+    GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported.
+  - gpio-ranges: Range of pins managed by the GPIO controller.
+
+Optional properties:
+
+  - clocks: Must contain a reference to the functional clock.  The property is
+    mandatory if the hardware implements a controllable functional clock for
+    the GPIO instance.
+
+Please refer to gpio.txt in this directory for details of gpio-ranges property
+and the common GPIO bindings used by client devices.
+
+The GPIO controller also acts as an interrupt controller. It uses the default
+two cells specifier as described in Documentation/devicetree/bindings/
+interrupt-controller/interrupts.txt.
+
+Example: R8A7779 (R-Car H1) GPIO controller nodes
+
+	gpio0: gpio@ffc40000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc40000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 141 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 0 32>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+	...
+	gpio6: gpio@ffc46000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc46000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 147 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 192 9>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt
new file mode 100644
index 000000000..dd5d2c039
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt
@@ -0,0 +1,60 @@
+* Synopsys DesignWare APB GPIO controller
+
+Required properties:
+- compatible : Should contain "snps,dw-apb-gpio"
+- reg : Address and length of the register set for the device.
+- #address-cells : should be 1 (for addressing port subnodes).
+- #size-cells : should be 0 (port subnodes).
+
+The GPIO controller has a configurable number of ports, each of which are
+represented as child nodes with the following properties:
+
+Required properties:
+- compatible : "snps,dw-apb-gpio-port"
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify the gpio polarity:
+      0 = active high
+      1 = active low
+- reg : The integer port index of the port, a single cell.
+
+Optional properties:
+- interrupt-controller : The first port may be configured to be an interrupt
+controller.
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt.  Shall be set to 2.  The first cell defines the interrupt number,
+  the second encodes the triger flags encoded as described in
+  Documentation/devicetree/bindings/interrupts.txt
+- interrupt-parent : The parent interrupt controller.
+- interrupts : The interrupt to the parent controller raised when GPIOs
+  generate the interrupts.
+- snps,nr-gpios : The number of pins in the port, a single cell.
+
+Example:
+
+gpio: gpio@20000 {
+	compatible = "snps,dw-apb-gpio";
+	reg = <0x20000 0x1000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	porta: gpio-controller@0 {
+		compatible = "snps,dw-apb-gpio-port";
+		gpio-controller;
+		#gpio-cells = <2>;
+		snps,nr-gpios = <8>;
+		reg = <0>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&vic1>;
+		interrupts = <0>;
+	};
+
+	portb: gpio-controller@1 {
+		compatible = "snps,dw-apb-gpio-port";
+		gpio-controller;
+		#gpio-cells = <2>;
+		snps,nr-gpios = <8>;
+		reg = <1>;
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/sodaville.txt b/kernel/Documentation/devicetree/bindings/gpio/sodaville.txt
new file mode 100644
index 000000000..563eff22b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/sodaville.txt
@@ -0,0 +1,48 @@
+GPIO controller on CE4100 / Sodaville SoCs
+==========================================
+
+The bindings for CE4100's GPIO controller match the generic description
+which is covered by the gpio.txt file in this folder.
+
+The only additional property is the intel,muxctl property which holds the
+value which is written into the MUXCNTL register.
+
+There is no compatible property for now because the driver is probed via
+PCI id (vendor 0x8086 device 0x2e67).
+
+The interrupt specifier consists of two cells encoded as follows:
+ - <1st cell>: The interrupt-number that identifies the interrupt source.
+ - <2nd cell>: The level-sense information, encoded as follows:
+		4 - active high level-sensitive
+		8 - active low level-sensitive
+
+Example of the GPIO device and one user:
+
+	pcigpio: gpio@b,1 {
+			/* two cells for GPIO and interrupt */
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			compatible = "pci8086,2e67.2",
+					   "pci8086,2e67",
+					   "pciclassff0000",
+					   "pciclassff00";
+
+			reg = <0x15900 0x0 0x0 0x0 0x0>;
+			/* Interrupt line of the gpio device */
+			interrupts = <15 1>;
+			/* It is an interrupt and GPIO controller itself */
+			interrupt-controller;
+			gpio-controller;
+			intel,muxctl = <0>;
+	};
+
+	testuser@20 {
+			compatible = "example,testuser";
+			/* User the 11th GPIO line as an active high triggered
+			 * level interrupt
+			 */
+			interrupts = <11 8>;
+			interrupt-parent = <&pcigpio>;
+			/* Use this GPIO also with the gpio functions */
+			gpios = <&pcigpio 11 0>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/gpio/spear_spics.txt b/kernel/Documentation/devicetree/bindings/gpio/spear_spics.txt
new file mode 100644
index 000000000..96c37eb15
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/gpio/spear_spics.txt
@@ -0,0 +1,50 @@
+=== ST Microelectronics SPEAr SPI CS Driver ===
+
+SPEAr platform provides a provision to control chipselects of ARM PL022 Prime
+Cell spi controller through its system registers, which otherwise remains under
+PL022 control. If chipselect remain under PL022 control then they would be
+released as soon as transfer is over and TxFIFO becomes empty. This is not
+desired by some of the device protocols above spi which expect (multiple)
+transfers without releasing their chipselects.
+
+Chipselects can be controlled by software by turning them as GPIOs. SPEAr
+provides another interface through system registers through which software can
+directly control each PL022 chipselect. Hence, it is natural for SPEAr to export
+the control of this interface as gpio.
+
+Required properties:
+
+  * compatible: should be defined as "st,spear-spics-gpio"
+  * reg: mentioning address range of spics controller
+  * st-spics,peripcfg-reg: peripheral configuration register offset
+  * st-spics,sw-enable-bit: bit offset to enable sw control
+  * st-spics,cs-value-bit: bit offset to drive chipselect low or high
+  * st-spics,cs-enable-mask: chip select number bit mask
+  * st-spics,cs-enable-shift: chip select number program offset
+  * gpio-controller: Marks the device node as gpio controller
+  * #gpio-cells: should be 1 and will mention chip select number
+
+All the above bit offsets are within peripcfg register.
+
+Example:
+-------
+spics: spics@e0700000{
+        compatible = "st,spear-spics-gpio";
+        reg = <0xe0700000 0x1000>;
+        st-spics,peripcfg-reg = <0x3b0>;
+        st-spics,sw-enable-bit = <12>;
+        st-spics,cs-value-bit = <11>;
+        st-spics,cs-enable-mask = <3>;
+        st-spics,cs-enable-shift = <8>;
+        gpio-controller;
+        #gpio-cells = <2>;
+};
+
+
+spi0: spi@e0100000 {
+        status = "okay";
+        num-cs = <3>;
+        cs-gpios = <&gpio1 7 0>, <&spics 0>,
+                   <&spics 1>;
+	...
+}