From 9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00 Mon Sep 17 00:00:00 2001 From: Yunhong Jiang Date: Tue, 4 Aug 2015 12:17:53 -0700 Subject: Add the rt linux 4.1.3-rt3 as base Import the rt linux 4.1.3-rt3 as OPNFV kvm base. It's from git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git linux-4.1.y-rt and the base is: commit 0917f823c59692d751951bf5ea699a2d1e2f26a2 Author: Sebastian Andrzej Siewior Date: Sat Jul 25 12:13:34 2015 +0200 Prepare v4.1.3-rt3 Signed-off-by: Sebastian Andrzej Siewior We lose all the git history this way and it's not good. We should apply another opnfv project repo in future. Change-Id: I87543d81c9df70d99c5001fbdf646b202c19f423 Signed-off-by: Yunhong Jiang --- .../devicetree/bindings/gpio/8xxx_gpio.txt | 74 +++++++ .../devicetree/bindings/gpio/abilis,tb10x-gpio.txt | 36 +++ .../devicetree/bindings/gpio/brcm,kona-gpio.txt | 52 +++++ .../bindings/gpio/cavium-octeon-gpio.txt | 49 +++++ .../bindings/gpio/cirrus,clps711x-mctrl-gpio.txt | 17 ++ .../devicetree/bindings/gpio/fsl-imx-gpio.txt | 32 +++ .../bindings/gpio/fujitsu,mb86s70-gpio.txt | 20 ++ .../devicetree/bindings/gpio/gpio-74x164.txt | 22 ++ .../devicetree/bindings/gpio/gpio-74xx-mmio.txt | 30 +++ .../devicetree/bindings/gpio/gpio-adnp.txt | 34 +++ .../devicetree/bindings/gpio/gpio-altera.txt | 43 ++++ .../devicetree/bindings/gpio/gpio-clps711x.txt | 28 +++ .../devicetree/bindings/gpio/gpio-davinci.txt | 62 ++++++ .../devicetree/bindings/gpio/gpio-dsp-keystone.txt | 39 ++++ .../devicetree/bindings/gpio/gpio-fan.txt | 40 ++++ .../devicetree/bindings/gpio/gpio-grgpio.txt | 26 +++ .../devicetree/bindings/gpio/gpio-lp3943.txt | 37 ++++ .../devicetree/bindings/gpio/gpio-max732x.txt | 59 +++++ .../devicetree/bindings/gpio/gpio-mcp23s08.txt | 85 ++++++++ .../devicetree/bindings/gpio/gpio-mm-lantiq.txt | 38 ++++ .../devicetree/bindings/gpio/gpio-msm.txt | 26 +++ .../devicetree/bindings/gpio/gpio-mvebu.txt | 53 +++++ .../devicetree/bindings/gpio/gpio-mxs.txt | 88 ++++++++ .../devicetree/bindings/gpio/gpio-nmk.txt | 31 +++ .../devicetree/bindings/gpio/gpio-omap.txt | 39 ++++ .../devicetree/bindings/gpio/gpio-palmas.txt | 27 +++ .../devicetree/bindings/gpio/gpio-pca953x.txt | 39 ++++ .../devicetree/bindings/gpio/gpio-pcf857x.txt | 71 ++++++ .../devicetree/bindings/gpio/gpio-poweroff.txt | 36 +++ .../devicetree/bindings/gpio/gpio-restart.txt | 54 +++++ .../devicetree/bindings/gpio/gpio-samsung.txt | 41 ++++ .../bindings/gpio/gpio-stericsson-coh901.txt | 7 + .../devicetree/bindings/gpio/gpio-stmpe.txt | 18 ++ .../devicetree/bindings/gpio/gpio-stp-xway.txt | 42 ++++ .../devicetree/bindings/gpio/gpio-sx150x.txt | 40 ++++ .../devicetree/bindings/gpio/gpio-twl4030.txt | 29 +++ .../devicetree/bindings/gpio/gpio-tz1090-pdc.txt | 45 ++++ .../devicetree/bindings/gpio/gpio-tz1090.txt | 88 ++++++++ .../devicetree/bindings/gpio/gpio-vf610.txt | 55 +++++ .../devicetree/bindings/gpio/gpio-xgene-sb.txt | 32 +++ .../devicetree/bindings/gpio/gpio-xgene.txt | 22 ++ .../devicetree/bindings/gpio/gpio-xilinx.txt | 48 ++++ .../devicetree/bindings/gpio/gpio-zevio.txt | 16 ++ .../devicetree/bindings/gpio/gpio-zynq.txt | 26 +++ .../devicetree/bindings/gpio/gpio.txt | 242 +++++++++++++++++++++ .../devicetree/bindings/gpio/gpio_atmel.txt | 25 +++ .../devicetree/bindings/gpio/gpio_lpc32xx.txt | 43 ++++ .../devicetree/bindings/gpio/moxa,moxart-gpio.txt | 19 ++ .../devicetree/bindings/gpio/mrvl-gpio.txt | 69 ++++++ .../bindings/gpio/nvidia,tegra20-gpio.txt | 40 ++++ .../devicetree/bindings/gpio/pl061-gpio.txt | 10 + .../devicetree/bindings/gpio/renesas,gpio-rcar.txt | 63 ++++++ .../devicetree/bindings/gpio/snps-dwapb-gpio.txt | 60 +++++ .../devicetree/bindings/gpio/sodaville.txt | 48 ++++ .../devicetree/bindings/gpio/spear_spics.txt | 50 +++++ 55 files changed, 2465 insertions(+) create mode 100644 kernel/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/fujitsu,mb86s70-gpio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-74x164.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-74xx-mmio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-adnp.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-altera.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-davinci.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-fan.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-lp3943.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-max732x.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-msm.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-mxs.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-nmk.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-omap.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-palmas.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-restart.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-samsung.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-stericsson-coh901.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-tz1090-pdc.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-tz1090.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-vf610.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-xgene.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-zevio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio-zynq.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio_atmel.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/moxa,moxart-gpio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/pl061-gpio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/sodaville.txt create mode 100644 kernel/Documentation/devicetree/bindings/gpio/spear_spics.txt (limited to 'kernel/Documentation/devicetree/bindings/gpio') diff --git a/kernel/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt new file mode 100644 index 000000000..798cfc9d3 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt @@ -0,0 +1,74 @@ +GPIO controllers on MPC8xxx SoCs + +This is for the non-QE/CPM/GUTs GPIO controllers as found on +8349, 8572, 8610 and compatible. + +Every GPIO controller node must have #gpio-cells property defined, +this information will be used to translate gpio-specifiers. +See bindings/gpio/gpio.txt for details of how to specify GPIO +information for devices. + +The GPIO module usually is connected to the SoC's internal interrupt +controller, see bindings/interrupt-controller/interrupts.txt (the +interrupt client nodes section) for details how to specify this GPIO +module's interrupt. + +The GPIO module may serve as another interrupt controller (cascaded to +the SoC's internal interrupt controller). See the interrupt controller +nodes section in bindings/interrupt-controller/interrupts.txt for +details. + +Required properties: +- compatible: "fsl,-gpio" followed by "fsl,mpc8349-gpio" + for 83xx, "fsl,mpc8572-gpio" for 85xx, or + "fsl,mpc8610-gpio" for 86xx. +- #gpio-cells: Should be two. The first cell is the pin number + and the second cell is used to specify optional + parameters (currently unused). +- interrupt-parent: Phandle for the interrupt controller that + services interrupts for this device. +- interrupts: Interrupt mapping for GPIO IRQ. +- gpio-controller: Marks the port as GPIO controller. + +Optional properties: +- interrupt-controller: Empty boolean property which marks the GPIO + module as an IRQ controller. +- #interrupt-cells: Should be two. Defines the number of integer + cells required to specify an interrupt within + this interrupt controller. The first cell + defines the pin number, the second cell + defines additional flags (trigger type, + trigger polarity). Note that the available + set of trigger conditions supported by the + GPIO module depends on the actual SoC. + +Example of gpio-controller nodes for a MPC8347 SoC: + + gpio1: gpio-controller@c00 { + #gpio-cells = <2>; + compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; + reg = <0xc00 0x100>; + interrupt-parent = <&ipic>; + interrupts = <74 0x8>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio-controller@d00 { + #gpio-cells = <2>; + compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio"; + reg = <0xd00 0x100>; + interrupt-parent = <&ipic>; + interrupts = <75 0x8>; + gpio-controller; + }; + +Example of a peripheral using the GPIO module as an IRQ controller: + + funkyfpga@0 { + compatible = "funky-fpga"; + ... + interrupt-parent = <&gpio1>; + interrupts = <4 3>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt new file mode 100644 index 000000000..00611acee --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/abilis,tb10x-gpio.txt @@ -0,0 +1,36 @@ +* Abilis TB10x GPIO controller + +Required Properties: +- compatible: Should be "abilis,tb10x-gpio" +- reg: Address and length of the register set for the device +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be <2>. The first cell is the pin number and the + second cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted). +- abilis,ngpio: the number of GPIO pins this driver controls. + +Optional Properties: +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be <1>. Interrupts are triggered on both edges. +- interrupts: Defines the interrupt line connecting this GPIO controller to + its parent interrupt controller. +- interrupt-parent: Defines the parent interrupt controller. + +GPIO ranges are specified as described in +Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + + gpioa: gpio@FF140000 { + compatible = "abilis,tb10x-gpio"; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&tb10x_ictl>; + interrupts = <27 2>; + reg = <0xFF140000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + abilis,ngpio = <3>; + gpio-ranges = <&iomux 0 0 0>; + gpio-ranges-group-names = "gpioa_pins"; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt new file mode 100644 index 000000000..4a63bc96b --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt @@ -0,0 +1,52 @@ +Broadcom Kona Family GPIO +========================= + +This GPIO driver is used in the following Broadcom SoCs: + BCM11130, BCM11140, BCM11351, BCM28145, BCM28155 + +The Broadcom GPIO Controller IP can be configured prior to synthesis to +support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The +GPIO controller only supports edge, not level, triggering of interrupts. + +Required properties +------------------- + +- compatible: "brcm,bcm11351-gpio", "brcm,kona-gpio" +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt outputs from the controller. There is one GPIO + interrupt per GPIO bank. The number of interrupts listed depends on the + number of GPIO banks on the SoC. The interrupts must be ordered by bank, + starting with bank 0. There is always a 1:1 mapping between banks and + IRQs. +- #gpio-cells: Should be <2>. The first cell is the pin number, the second + cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) + See also "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt. +- #interrupt-cells: Should be <2>. The first cell is the GPIO number. The + second cell is used to specify flags. The following subset of flags is + supported: + - trigger type (bits[1:0]): + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 3 = low-to-high or high-to-low edge triggered + Valid values are 1, 2, 3 + See also .../devicetree/bindings/interrupt-controller/interrupts.txt. +- gpio-controller: Marks the device node as a GPIO controller. +- interrupt-controller: Marks the device node as an interrupt controller. + +Example: + gpio: gpio@35003000 { + compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio"; + reg = <0x35003000 0x800>; + interrupts = + ; + #gpio-cells = <2>; + #interrupt-cells = <2>; + gpio-controller; + interrupt-controller; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt new file mode 100644 index 000000000..9d6dcd3fe --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt @@ -0,0 +1,49 @@ +* General Purpose Input Output (GPIO) bus. + +Properties: +- compatible: "cavium,octeon-3860-gpio" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the GPIO unit's register bank. + +- gpio-controller: This is a GPIO controller. + +- #gpio-cells: Must be <2>. The first cell is the GPIO pin. + +- interrupt-controller: The GPIO controller is also an interrupt + controller, many of its pins may be configured as an interrupt + source. + +- #interrupt-cells: Must be <2>. The first cell is the GPIO pin + connected to the interrupt source. The second cell is the interrupt + triggering protocol and may have one of four values: + 1 - edge triggered on the rising edge. + 2 - edge triggered on the falling edge + 4 - level triggered active high. + 8 - level triggered active low. + +- interrupts: Interrupt routing for each pin. + +Example: + + gpio-controller@1070000000800 { + #gpio-cells = <2>; + compatible = "cavium,octeon-3860-gpio"; + reg = <0x10700 0x00000800 0x0 0x100>; + gpio-controller; + /* Interrupts are specified by two parts: + * 1) GPIO pin number (0..15) + * 2) Triggering (1 - edge rising + * 2 - edge falling + * 4 - level active high + * 8 - level active low) + */ + interrupt-controller; + #interrupt-cells = <2>; + /* The GPIO pin connect to 16 consecutive CUI bits */ + interrupts = <0 16>, <0 17>, <0 18>, <0 19>, + <0 20>, <0 21>, <0 22>, <0 23>, + <0 24>, <0 25>, <0 26>, <0 27>, + <0 28>, <0 29>, <0 30>, <0 31>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt new file mode 100644 index 000000000..94ae9f82d --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt @@ -0,0 +1,17 @@ +* ARM Cirrus Logic CLPS711X SYSFLG1 MCTRL GPIOs + +Required properties: +- compatible: Should contain "cirrus,clps711x-mctrl-gpio". +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = Active high, + 1 = Active low. + +Example: + sysgpio: sysgpio { + compatible = "cirrus,ep7312-mctrl-gpio", + "cirrus,clps711x-mctrl-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt new file mode 100644 index 000000000..dbd22e0df --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt @@ -0,0 +1,32 @@ +* Freescale i.MX/MXC GPIO controller + +Required properties: +- compatible : Should be "fsl,-gpio" +- reg : Address and length of the register set for the device +- interrupts : Should be the port interrupt shared by all 32 pins, if + one number. If two numbers, the first one is the interrupt shared + by low 16 pins and the second one is for high 16 pins. +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells : Should be 2. The first cell is the GPIO number. + The second cell bits[3:0] is used to specify trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + +Example: + +gpio0: gpio@73f84000 { + compatible = "fsl,imx51-gpio", "fsl,imx35-gpio"; + reg = <0x73f84000 0x4000>; + interrupts = <50 51>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/fujitsu,mb86s70-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/fujitsu,mb86s70-gpio.txt new file mode 100644 index 000000000..bef353f37 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/fujitsu,mb86s70-gpio.txt @@ -0,0 +1,20 @@ +Fujitsu MB86S7x GPIO Controller +------------------------------- + +Required properties: +- compatible: Should be "fujitsu,mb86s70-gpio" +- reg: Base address and length of register space +- clocks: Specify the clock +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be <2>. The first cell is the pin number and the + second cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted). + +Examples: + gpio0: gpio@31000000 { + compatible = "fujitsu,mb86s70-gpio"; + reg = <0 0x31000000 0x10000>; + gpio-controller; + #gpio-cells = <2>; + clocks = <&clk 0 2 1>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-74x164.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-74x164.txt new file mode 100644 index 000000000..cc2608021 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-74x164.txt @@ -0,0 +1,22 @@ +* Generic 8-bits shift register GPIO driver + +Required properties: +- compatible : Should be "fairchild,74hc595" +- reg : chip select number +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- registers-number: Number of daisy-chained shift registers + +Example: + +gpio5: gpio5@0 { + compatible = "fairchild,74hc595"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + registers-number = <4>; + spi-max-frequency = <100000>; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-74xx-mmio.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-74xx-mmio.txt new file mode 100644 index 000000000..7bb1a9d60 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-74xx-mmio.txt @@ -0,0 +1,30 @@ +* 74XX MMIO GPIO driver + +Required properties: +- compatible: Should contain one of the following: + "ti,741g125": for 741G125 (1-bit Input), + "ti,741g174": for 741G74 (1-bit Output), + "ti,742g125": for 742G125 (2-bit Input), + "ti,7474" : for 7474 (2-bit Output), + "ti,74125" : for 74125 (4-bit Input), + "ti,74175" : for 74175 (4-bit Output), + "ti,74365" : for 74365 (6-bit Input), + "ti,74174" : for 74174 (6-bit Output), + "ti,74244" : for 74244 (8-bit Input), + "ti,74273" : for 74273 (8-bit Output), + "ti,741624" : for 741624 (16-bit Input), + "ti,7416374": for 7416374 (16-bit Output). +- reg: Physical base address and length where IC resides. +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify the GPIO polarity: + 0 = Active High, + 1 = Active Low. + +Example: + ctrl: gpio@30008004 { + compatible = "ti,74174"; + reg = <0x30008004 0x1>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-adnp.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-adnp.txt new file mode 100644 index 000000000..af66b2724 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-adnp.txt @@ -0,0 +1,34 @@ +Avionic Design N-bit GPIO expander bindings + +Required properties: +- compatible: should be "ad,gpio-adnp" +- reg: The I2C slave address for this device. +- interrupt-parent: phandle of the parent interrupt controller. +- interrupts: Interrupt specifier for the controllers interrupt. +- #gpio-cells: Should be 2. The first cell is the GPIO number and the + second cell is used to specify optional parameters: + - bit 0: polarity (0: normal, 1: inverted) +- gpio-controller: Marks the device as a GPIO controller +- nr-gpios: The number of pins supported by the controller. + +The GPIO expander can optionally be used as an interrupt controller, in +which case it uses the default two cell specifier as described in +Documentation/devicetree/bindings/interrupt-controller/interrupts.txt. + +Example: + + gpioext: gpio-controller@41 { + compatible = "ad,gpio-adnp"; + reg = <0x41>; + + interrupt-parent = <&gpio>; + interrupts = <160 1>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + + nr-gpios = <64>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-altera.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-altera.txt new file mode 100644 index 000000000..12f50149e --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-altera.txt @@ -0,0 +1,43 @@ +Altera GPIO controller bindings + +Required properties: +- compatible: + - "altr,pio-1.0" +- reg: Physical base address and length of the controller's registers. +- #gpio-cells : Should be 2 + - The first cell is the gpio offset number. + - The second cell is reserved and is currently unused. +- gpio-controller : Marks the device node as a GPIO controller. +- interrupt-controller: Mark the device node as an interrupt controller +- #interrupt-cells : Should be 1. The interrupt type is fixed in the hardware. + - The first cell is the GPIO offset number within the GPIO controller. +- interrupts: Specify the interrupt. +- altr,interrupt-trigger: Specifies the interrupt trigger type the GPIO + hardware is synthesized. This field is required if the Altera GPIO controller + used has IRQ enabled as the interrupt type is not software controlled, + but hardware synthesized. Required if GPIO is used as an interrupt + controller. The value is defined in + Only the following flags are supported: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + IRQ_TYPE_LEVEL_HIGH + +Optional properties: +- altr,ngpio: Width of the GPIO bank. This defines how many pins the + GPIO device has. Ranges between 1-32. Optional and defaults to 32 if not + specified. + +Example: + +gpio_altr: gpio@0xff200000 { + compatible = "altr,pio-1.0"; + reg = <0xff200000 0x10>; + interrupts = <0 45 4>; + altr,ngpio = <32>; + altr,interrupt-trigger = ; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <1>; + interrupt-controller; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt new file mode 100644 index 000000000..e0d0446a6 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt @@ -0,0 +1,28 @@ +Cirrus Logic CLPS711X GPIO controller + +Required properties: +- compatible: Should be "cirrus,clps711x-gpio" +- reg: Physical base GPIO controller registers location and length. + There should be two registers, first is DATA register, the second + is DIRECTION. +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + +Note: Each GPIO port should have an alias correctly numbered in "aliases" +node. + +Example: + +aliases { + gpio0 = &porta; +}; + +porta: gpio@80000000 { + compatible = "cirrus,clps711x-gpio"; + reg = <0x80000000 0x1>, <0x80000040 0x1>; + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-davinci.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-davinci.txt new file mode 100644 index 000000000..5079ba7d6 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-davinci.txt @@ -0,0 +1,62 @@ +Davinci/Keystone GPIO controller bindings + +Required Properties: +- compatible: should be "ti,dm6441-gpio", "ti,keystone-gpio" + +- reg: Physical base address of the controller and the size of memory mapped + registers. + +- gpio-controller : Marks the device node as a gpio controller. + +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify optional parameters (unused) + +- interrupt-parent: phandle of the parent interrupt controller. + +- interrupts: Array of GPIO interrupt number. Only banked or unbanked IRQs are + supported at a time. + +- ti,ngpio: The number of GPIO pins supported. + +- ti,davinci-gpio-unbanked: The number of GPIOs that have an individual interrupt + line to processor. + +The GPIO controller also acts as an interrupt controller. It uses the default +two cells specifier as described in Documentation/devicetree/bindings/ +interrupt-controller/interrupts.txt. + +Example: + +gpio: gpio@1e26000 { + compatible = "ti,dm6441-gpio"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x226000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <42 IRQ_TYPE_EDGE_BOTH 43 IRQ_TYPE_EDGE_BOTH + 44 IRQ_TYPE_EDGE_BOTH 45 IRQ_TYPE_EDGE_BOTH + 46 IRQ_TYPE_EDGE_BOTH 47 IRQ_TYPE_EDGE_BOTH + 48 IRQ_TYPE_EDGE_BOTH 49 IRQ_TYPE_EDGE_BOTH + 50 IRQ_TYPE_EDGE_BOTH>; + ti,ngpio = <144>; + ti,davinci-gpio-unbanked = <0>; + interrupt-controller; + #interrupt-cells = <2>; +}; + +leds { + compatible = "gpio-leds"; + + led1 { + label = "davinci:green:usr1"; + gpios = <&gpio 10 GPIO_ACTIVE_HIGH>; + ... + }; + + led2 { + label = "davinci:red:debug1"; + gpios = <&gpio 11 GPIO_ACTIVE_HIGH>; + ... + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt new file mode 100644 index 000000000..6c7e6c730 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-dsp-keystone.txt @@ -0,0 +1,39 @@ +Keystone 2 DSP GPIO controller bindings + +HOST OS userland running on ARM can send interrupts to DSP cores using +the DSP GPIO controller IP. It provides 28 IRQ signals per each DSP core. +This is one of the component used by the IPC mechanism used on Keystone SOCs. + +For example TCI6638K2K SoC has 8 DSP GPIO controllers: + - 8 for C66x CorePacx CPUs 0-7 + +Keystone 2 DSP GPIO controller has specific features: +- each GPIO can be configured only as output pin; +- setting GPIO value to 1 causes IRQ generation on target DSP core; +- reading pin value returns 0 - if IRQ was handled or 1 - IRQ is still + pending. + +Required Properties: +- compatible: should be "ti,keystone-dsp-gpio" +- ti,syscon-dev: phandle/offset pair. The phandle to syscon used to + access device state control registers and the offset of device's specific + registers within device state control registers range. +- gpio-controller: Marks the device node as a gpio controller. +- #gpio-cells: Should be 2. + +Please refer to gpio.txt in this directory for details of the common GPIO +bindings used by client devices. + +Example: + dspgpio0: keystone_dsp_gpio@02620240 { + compatible = "ti,keystone-dsp-gpio"; + ti,syscon-dev = <&devctrl 0x240>; + gpio-controller; + #gpio-cells = <2>; + }; + + dsp0: dsp0 { + compatible = "linux,rproc-user"; + ... + kick-gpio = <&dspgpio0 27>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-fan.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-fan.txt new file mode 100644 index 000000000..439a7430f --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-fan.txt @@ -0,0 +1,40 @@ +Bindings for fan connected to GPIO lines + +Required properties: +- compatible : "gpio-fan" + +Optional properties: +- gpios: Specifies the pins that map to bits in the control value, + ordered MSB-->LSB. +- gpio-fan,speed-map: A mapping of possible fan RPM speeds and the + control value that should be set to achieve them. This array + must have the RPM values in ascending order. +- alarm-gpios: This pin going active indicates something is wrong with + the fan, and a udev event will be fired. +- cooling-cells: If used as a cooling device, must be <2> + Also see: Documentation/devicetree/bindings/thermal/thermal.txt + min and max states are derived from the speed-map of the fan. + +Note: At least one the "gpios" or "alarm-gpios" properties must be set. + +Examples: + + gpio_fan { + compatible = "gpio-fan"; + gpios = <&gpio1 14 1 + &gpio1 13 1>; + gpio-fan,speed-map = <0 0 + 3000 1 + 6000 2>; + alarm-gpios = <&gpio1 15 1>; + }; + gpio_fan_cool: gpio_fan { + compatible = "gpio-fan"; + gpios = <&gpio2 14 1 + &gpio2 13 1>; + gpio-fan,speed-map = <0 0>, + <3000 1>, + <6000 2>; + alarm-gpios = <&gpio2 15 1>; + #cooling-cells = <2>; /* min followed by max */ + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt new file mode 100644 index 000000000..e46659810 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt @@ -0,0 +1,26 @@ +Aeroflex Gaisler GRGPIO General Purpose I/O cores. + +The GRGPIO GPIO core is available in the GRLIB VHDL IP core library. + +Note: In the ordinary environment for the GRGPIO core, a Leon SPARC system, +these properties are built from information in the AMBA plug&play. + +Required properties: + +- name : Should be "GAISLER_GPIO" or "01_01a" + +- reg : Address and length of the register set for the device + +- interrupts : Interrupt numbers for this device + +Optional properties: + +- nbits : The number of gpio lines. If not present driver assumes 32 lines. + +- irqmap : An array with an index for each gpio line. An index is either a valid + index into the interrupts property array, or 0xffffffff that indicates + no irq for that line. Driver provides no interrupt support if not + present. + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdf diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-lp3943.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-lp3943.txt new file mode 100644 index 000000000..80fcb7d70 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-lp3943.txt @@ -0,0 +1,37 @@ +TI/National Semiconductor LP3943 GPIO controller + +Required properties: + - compatible: "ti,lp3943-gpio" + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be 2. See gpio.txt in this directory for a + description of the cells format. + +Example: +Simple LED controls with LP3943 GPIO controller + +&i2c4 { + lp3943@60 { + compatible = "ti,lp3943"; + reg = <0x60>; + + gpioex: gpio { + compatible = "ti,lp3943-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + }; +}; + +leds { + compatible = "gpio-leds"; + indicator1 { + label = "indi1"; + gpios = <&gpioex 9 GPIO_ACTIVE_LOW>; + }; + + indicator2 { + label = "indi2"; + gpios = <&gpioex 10 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-max732x.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-max732x.txt new file mode 100644 index 000000000..5fdc843b4 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-max732x.txt @@ -0,0 +1,59 @@ +* MAX732x-compatible I/O expanders + +Required properties: + - compatible: Should be one of the following: + - "maxim,max7319": For the Maxim MAX7319 + - "maxim,max7320": For the Maxim MAX7320 + - "maxim,max7321": For the Maxim MAX7321 + - "maxim,max7322": For the Maxim MAX7322 + - "maxim,max7323": For the Maxim MAX7323 + - "maxim,max7324": For the Maxim MAX7324 + - "maxim,max7325": For the Maxim MAX7325 + - "maxim,max7326": For the Maxim MAX7326 + - "maxim,max7327": For the Maxim MAX7327 + - reg: I2C slave address for this device. + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be 2. + - first cell is the GPIO number + - second cell specifies GPIO flags, as defined in . + Only the GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. + +Optional properties: + + The I/O expander can detect input state changes, and thus optionally act as + an interrupt controller. When the expander interrupt line is connected all the + following properties must be set. For more information please see the + interrupt controller device tree bindings documentation available at + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt. + + - interrupt-controller: Identifies the node as an interrupt controller. + - #interrupt-cells: Number of cells to encode an interrupt source, shall be 2. + - first cell is the pin number + - second cell is used to specify flags + - interrupt-parent: phandle of the parent interrupt controller. + - interrupts: Interrupt specifier for the controllers interrupt. + +Please refer to gpio.txt in this directory for details of the common GPIO +bindings used by client devices. + +Example 1. MAX7325 with interrupt support enabled (CONFIG_GPIO_MAX732X_IRQ=y): + + expander: max7325@6d { + compatible = "maxim,max7325"; + reg = <0x6d>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gpio4>; + interrupts = <29 IRQ_TYPE_EDGE_FALLING>; + }; + +Example 2. MAX7325 with interrupt support disabled (CONFIG_GPIO_MAX732X_IRQ=n): + + expander: max7325@6d { + compatible = "maxim,max7325"; + reg = <0x6d>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt new file mode 100644 index 000000000..f3332b9a8 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt @@ -0,0 +1,85 @@ +Microchip MCP2308/MCP23S08/MCP23017/MCP23S17 driver for +8-/16-bit I/O expander with serial interface (I2C/SPI) + +Required properties: +- compatible : Should be + - "mcp,mcp23s08" (DEPRECATED) for 8 GPIO SPI version + - "mcp,mcp23s17" (DEPRECATED) for 16 GPIO SPI version + - "mcp,mcp23008" (DEPRECATED) for 8 GPIO I2C version or + - "mcp,mcp23017" (DEPRECATED) for 16 GPIO I2C version of the chip + + - "microchip,mcp23s08" for 8 GPIO SPI version + - "microchip,mcp23s17" for 16 GPIO SPI version + - "microchip,mcp23008" for 8 GPIO I2C version or + - "microchip,mcp23017" for 16 GPIO I2C version of the chip + NOTE: Do not use the old mcp prefix any more. It is deprecated and will be + removed. +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify flags. Flags are currently unused. +- gpio-controller : Marks the device node as a GPIO controller. +- reg : For an address on its bus. I2C uses this a the I2C address of the chip. + SPI uses this to specify the chipselect line which the chip is + connected to. The driver and the SPI variant of the chip support + multiple chips on the same chipselect. Have a look at + microchip,spi-present-mask below. + +Required device specific properties (only for SPI chips): +- mcp,spi-present-mask (DEPRECATED) +- microchip,spi-present-mask : This is a present flag, that makes only sense for SPI + chips - as the name suggests. Multiple SPI chips can share the same + SPI chipselect. Set a bit in bit0-7 in this mask to 1 if there is a + chip connected with the corresponding spi address set. For example if + you have a chip with address 3 connected, you have to set bit3 to 1, + which is 0x08. mcp23s08 chip variant only supports bits 0-3. It is not + possible to mix mcp23s08 and mcp23s17 on the same chipselect. Set at + least one bit to 1 for SPI chips. + NOTE: Do not use the old mcp prefix any more. It is deprecated and will be + removed. +- spi-max-frequency = The maximum frequency this chip is able to handle + +Optional properties: +- #interrupt-cells : Should be two. + - first cell is the pin number + - second cell is used to specify flags. +- interrupt-controller: Marks the device node as a interrupt controller. +NOTE: The interrupt functionality is only supported for i2c versions of the +chips. The spi chips can also do the interrupts, but this is not supported by +the linux driver yet. + +Optional device specific properties: +- microchip,irq-mirror: Sets the mirror flag in the IOCON register. Devices + with two interrupt outputs (these are the devices ending with 17 and + those that have 16 IOs) have two IO banks: IO 0-7 form bank 1 and + IO 8-15 are bank 2. These chips have two different interrupt outputs: + One for bank 1 and another for bank 2. If irq-mirror is set, both + interrupts are generated regardless of the bank that an input change + occurred on. If it is not set, the interrupt are only generated for the + bank they belong to. + On devices with only one interrupt output this property is useless. +- microchip,irq-active-high: Sets the INTPOL flag in the IOCON register. This + configures the IRQ output polarity as active high. + +Example I2C (with interrupt): +gpiom1: gpio@20 { + compatible = "microchip,mcp23017"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + + interrupt-parent = <&gpio1>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells=<2>; + microchip,irq-mirror; +}; + +Example SPI: +gpiom1: gpio@0 { + compatible = "microchip,mcp23s17"; + gpio-controller; + #gpio-cells = <2>; + spi-present-mask = <0x01>; + reg = <0>; + spi-max-frequency = <1000000>; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt new file mode 100644 index 000000000..f93d51478 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt @@ -0,0 +1,38 @@ +Lantiq SoC External Bus memory mapped GPIO controller + +By attaching hardware latches to the EBU it is possible to create output +only gpios. This driver configures a special memory address, which when +written to outputs 16 bit to the latches. + +The node describing the memory mapped GPIOs needs to be a child of the node +describing the "lantiq,localbus". + +Required properties: +- compatible : Should be "lantiq,gpio-mm-lantiq" +- reg : Address and length of the register set for the device +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters (currently + unused). +- gpio-controller : Marks the device node as a gpio controller. + +Optional properties: +- lantiq,shadow : The default value that we shall assume as already set on the + shift register cascade. + +Example: + +localbus@0 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x0 0x3ffffff /* addrsel0 */ + 1 0 0x4000000 0x4000010>; /* addsel1 */ + compatible = "lantiq,localbus", "simple-bus"; + + gpio_mm0: gpio@4000000 { + compatible = "lantiq,gpio-mm"; + reg = <1 0x0 0x10>; + gpio-controller; + #gpio-cells = <2>; + lantiq,shadow = <0x77f> + }; +} diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-msm.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-msm.txt new file mode 100644 index 000000000..ac20e68a0 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-msm.txt @@ -0,0 +1,26 @@ +MSM GPIO controller bindings + +Required properties: +- compatible: + - "qcom,msm-gpio" for MSM controllers +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify optional parameters (unused) +- gpio-controller : Marks the device node as a GPIO controller. +- #interrupt-cells : Should be 2. +- interrupt-controller: Mark the device node as an interrupt controller +- interrupts : Specify the TLMM summary interrupt number +- ngpio : Specify the number of MSM GPIOs + +Example: + + msmgpio: gpio@fd510000 { + compatible = "qcom,msm-gpio"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0xfd510000 0x4000>; + interrupts = <0 208 0>; + ngpio = <150>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt new file mode 100644 index 000000000..a6f3bec1d --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt @@ -0,0 +1,53 @@ +* Marvell EBU GPIO controller + +Required properties: + +- compatible : Should be "marvell,orion-gpio", "marvell,mv78200-gpio" + or "marvell,armadaxp-gpio". "marvell,orion-gpio" should be used for + Orion, Kirkwood, Dove, Discovery (except MV78200) and Armada + 370. "marvell,mv78200-gpio" should be used for the Discovery + MV78200. "marvel,armadaxp-gpio" should be used for all Armada XP + SoCs (MV78230, MV78260, MV78460). + +- reg: Address and length of the register set for the device. Only one + entry is expected, except for the "marvell,armadaxp-gpio" variant + for which two entries are expected: one for the general registers, + one for the per-cpu registers. + +- interrupts: The list of interrupts that are used for all the pins + managed by this GPIO bank. There can be more than one interrupt + (example: 1 interrupt per 8 pins on Armada XP, which means 4 + interrupts per bank of 32 GPIOs). + +- interrupt-controller: identifies the node as an interrupt controller + +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. Should be two. + The first cell is the GPIO number. + The second cell is used to specify flags: + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + +- gpio-controller: marks the device node as a gpio controller + +- ngpios: number of GPIOs this controller has + +- #gpio-cells: Should be two. The first cell is the pin number. The + second cell is reserved for flags, unused at the moment. + +Example: + + gpio0: gpio@d0018100 { + compatible = "marvell,armadaxp-gpio"; + reg = <0xd0018100 0x40>, + <0xd0018800 0x30>; + ngpios = <32>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <16>, <17>, <18>, <19>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-mxs.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-mxs.txt new file mode 100644 index 000000000..1e677a47b --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-mxs.txt @@ -0,0 +1,88 @@ +* Freescale MXS GPIO controller + +The Freescale MXS GPIO controller is part of MXS PIN controller. The +GPIOs are organized in port/bank. Each port consists of 32 GPIOs. + +As the GPIO controller is embedded in the PIN controller and all the +GPIO ports share the same IO space with PIN controller, the GPIO node +will be represented as sub-nodes of MXS pinctrl node. + +Required properties for GPIO node: +- compatible : Should be "fsl,-gpio". The supported SoCs include + imx23 and imx28. +- interrupts : Should be the port interrupt shared by all 32 pins. +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells : Should be 2. The first cell is the GPIO number. + The second cell bits[3:0] is used to specify trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + +Note: Each GPIO port should have an alias correctly numbered in "aliases" +node. + +Examples: + +aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + gpio4 = &gpio4; +}; + +pinctrl@80018000 { + compatible = "fsl,imx28-pinctrl", "simple-bus"; + reg = <0x80018000 2000>; + + gpio0: gpio@0 { + compatible = "fsl,imx28-gpio"; + interrupts = <127>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio@1 { + compatible = "fsl,imx28-gpio"; + interrupts = <126>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio@2 { + compatible = "fsl,imx28-gpio"; + interrupts = <125>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio@3 { + compatible = "fsl,imx28-gpio"; + interrupts = <124>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio4: gpio@4 { + compatible = "fsl,imx28-gpio"; + interrupts = <123>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-nmk.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-nmk.txt new file mode 100644 index 000000000..8315ac778 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-nmk.txt @@ -0,0 +1,31 @@ +Nomadik GPIO controller + +Required properties: +- compatible : Should be "st,nomadik-gpio". +- reg : Physical base address and length of the controller's registers. +- interrupts : The interrupt outputs from the controller. +- #gpio-cells : Should be two: + The first cell is the pin number. + The second cell is used to specify optional parameters: + - bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. +- gpio-controller : Marks the device node as a GPIO controller. +- interrupt-controller : Marks the device node as an interrupt controller. +- gpio-bank : Specifies which bank a controller owns. +- st,supports-sleepmode : Specifies whether controller can sleep or not + +Example: + + gpio1: gpio@8012e080 { + compatible = "st,nomadik-gpio"; + reg = <0x8012e080 0x80>; + interrupts = <0 120 0x4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + st,supports-sleepmode; + gpio-bank = <1>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-omap.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-omap.txt new file mode 100644 index 000000000..8d950522e --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-omap.txt @@ -0,0 +1,39 @@ +OMAP GPIO controller bindings + +Required properties: +- compatible: + - "ti,omap2-gpio" for OMAP2 controllers + - "ti,omap3-gpio" for OMAP3 controllers + - "ti,omap4-gpio" for OMAP4 controllers +- gpio-controller : Marks the device node as a GPIO controller. +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify optional parameters (unused) +- interrupt-controller: Mark the device node as an interrupt controller. +- #interrupt-cells : Should be 2. + The first cell is the GPIO number. + The second cell is used to specify flags: + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + +OMAP specific properties: +- ti,hwmods: Name of the hwmod associated to the GPIO: + "gpio", being the 1-based instance number + from the HW spec. +- ti,gpio-always-on: Indicates if a GPIO bank is always powered and + so will never lose its logic state. + + +Example: + +gpio4: gpio4 { + compatible = "ti,omap4-gpio"; + ti,hwmods = "gpio4"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-palmas.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-palmas.txt new file mode 100644 index 000000000..08b5b52a3 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-palmas.txt @@ -0,0 +1,27 @@ +Palmas GPIO controller bindings + +Required properties: +- compatible: + - "ti,palams-gpio" for palma series of the GPIO controller + - "ti,tps80036-gpio" for Palma series device TPS80036. + - "ti,tps65913-gpio" for palma series device TPS65913. + - "ti,tps65914-gpio" for palma series device TPS65914. +- #gpio-cells : Should be two. + - first cell is the gpio pin number + - second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- gpio-controller : Marks the device node as a GPIO controller. + +Note: This gpio node will be sub node of palmas node. + +Example: + palmas: tps65913@58 { + ::::::::::: + palmas_gpio: palmas_gpio { + compatible = "ti,palmas-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + ::::::::::: + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt new file mode 100644 index 000000000..b9a42f294 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -0,0 +1,39 @@ +* NXP PCA953x I2C GPIO multiplexer + +Required properties: + - compatible: Has to contain one of the following: + nxp,pca9505 + nxp,pca9534 + nxp,pca9535 + nxp,pca9536 + nxp,pca9537 + nxp,pca9538 + nxp,pca9539 + nxp,pca9554 + nxp,pca9555 + nxp,pca9556 + nxp,pca9557 + nxp,pca9574 + nxp,pca9575 + nxp,pca9698 + maxim,max7310 + maxim,max7312 + maxim,max7313 + maxim,max7315 + ti,pca6107 + ti,tca6408 + ti,tca6416 + ti,tca6424 + exar,xra1202 + +Example: + + + gpio@20 { + compatible = "nxp,pca9505"; + reg = <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pca9505>; + interrupt-parent = <&gpio3>; + interrupts = <23 IRQ_TYPE_LEVEL_LOW>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt new file mode 100644 index 000000000..ada4e2973 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-pcf857x.txt @@ -0,0 +1,71 @@ +* PCF857x-compatible I/O expanders + +The PCF857x-compatible chips have "quasi-bidirectional" I/O lines that can be +driven high by a pull-up current source or driven low to ground. This combines +the direction and output level into a single bit per line, which can't be read +back. We can't actually know at initialization time whether a line is configured +(a) as output and driving the signal low/high, or (b) as input and reporting a +low/high value, without knowing the last value written since the chip came out +of reset (if any). The only reliable solution for setting up line direction is +thus to do it explicitly. + +Required Properties: + + - compatible: should be one of the following. + - "maxim,max7328": For the Maxim MAX7378 + - "maxim,max7329": For the Maxim MAX7329 + - "nxp,pca8574": For the NXP PCA8574 + - "nxp,pca8575": For the NXP PCA8575 + - "nxp,pca9670": For the NXP PCA9670 + - "nxp,pca9671": For the NXP PCA9671 + - "nxp,pca9672": For the NXP PCA9672 + - "nxp,pca9673": For the NXP PCA9673 + - "nxp,pca9674": For the NXP PCA9674 + - "nxp,pca9675": For the NXP PCA9675 + - "nxp,pcf8574": For the NXP PCF8574 + - "nxp,pcf8574a": For the NXP PCF8574A + - "nxp,pcf8575": For the NXP PCF8575 + - "ti,tca9554": For the TI TCA9554 + + - reg: I2C slave address. + + - gpio-controller: Marks the device node as a gpio controller. + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in . Only the + GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. + +Optional Properties: + + - lines-initial-states: Bitmask that specifies the initial state of each + line. When a bit is set to zero, the corresponding line will be initialized to + the input (pulled-up) state. When the bit is set to one, the line will be + initialized the low-level output state. If the property is not specified + all lines will be initialized to the input state. + + The I/O expander can detect input state changes, and thus optionally act as + an interrupt controller. When the expander interrupt line is connected all the + following properties must be set. For more information please see the + interrupt controller device tree bindings documentation available at + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt. + + - interrupt-controller: Identifies the node as an interrupt controller. + - #interrupt-cells: Number of cells to encode an interrupt source, shall be 2. + - interrupt-parent: phandle of the parent interrupt controller. + - interrupts: Interrupt specifier for the controllers interrupt. + + +Please refer to gpio.txt in this directory for details of the common GPIO +bindings used by client devices. + +Example: PCF8575 I/O expander node + + pcf8575: gpio@20 { + compatible = "nxp,pcf8575"; + reg = <0x20>; + interrupt-parent = <&irqpin2>; + interrupts = <3 0>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt new file mode 100644 index 000000000..d4eab9227 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt @@ -0,0 +1,36 @@ +Driver a GPIO line that can be used to turn the power off. + +The driver supports both level triggered and edge triggered power off. +At driver load time, the driver will request the given gpio line and +install a pm_power_off handler. If the optional properties 'input' is +not found, the GPIO line will be driven in the inactive +state. Otherwise its configured as an input. + +When the pm_power_off is called, the gpio is configured as an output, +and drive active, so triggering a level triggered power off +condition. This will also cause an inactive->active edge condition, so +triggering positive edge triggered power off. After a delay of 100ms, +the GPIO is set to inactive, thus causing an active->inactive edge, +triggering negative edge triggered power off. After another 100ms +delay the GPIO is driver active again. If the power is still on and +the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted. + +Required properties: +- compatible : should be "gpio-poweroff". +- gpios : The GPIO to set high/low, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be + low to power down the board set it to "Active Low", otherwise set + gpio to "Active High". + +Optional properties: +- input : Initially configure the GPIO line as an input. Only reconfigure + it to an output when the pm_power_off function is called. If this optional + property is not specified, the GPIO is initialized as an output in its + inactive state. + +Examples: + +gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio 4 0>; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-restart.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-restart.txt new file mode 100644 index 000000000..af3701bc1 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-restart.txt @@ -0,0 +1,54 @@ +Drive a GPIO line that can be used to restart the system from a restart +handler. + +This binding supports level and edge triggered reset. At driver load +time, the driver will request the given gpio line and install a restart +handler. If the optional properties 'open-source' is not found, the GPIO line +will be driven in the inactive state. Otherwise its not driven until +the restart is initiated. + +When the system is restarted, the restart handler will be invoked in +priority order. The gpio is configured as an output, and driven active, +triggering a level triggered reset condition. This will also cause an +inactive->active edge condition, triggering positive edge triggered +reset. After a delay specified by active-delay, the GPIO is set to +inactive, thus causing an active->inactive edge, triggering negative edge +triggered reset. After a delay specified by inactive-delay, the GPIO +is driven active again. After a delay specified by wait-delay, the +restart handler completes allowing other restart handlers to be attempted. + +Required properties: +- compatible : should be "gpio-restart". +- gpios : The GPIO to set high/low, see "gpios property" in + Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be + low to reset the board set it to "Active Low", otherwise set + gpio to "Active High". + +Optional properties: +- open-source : Treat the GPIO as being open source and defer driving + it to when the restart is initiated. If this optional property is not + specified, the GPIO is initialized as an output in its inactive state. +- priority : A priority ranging from 0 to 255 (default 128) according to + the following guidelines: + 0: Restart handler of last resort, with limited restart + capabilities + 128: Default restart handler; use if no other restart handler is + expected to be available, and/or if restart functionality is + sufficient to restart the entire system + 255: Highest priority restart handler, will preempt all other + restart handlers +- active-delay: Delay (default 100) to wait after driving gpio active [ms] +- inactive-delay: Delay (default 100) to wait after driving gpio inactive [ms] +- wait-delay: Delay (default 3000) to wait after completing restart + sequence [ms] + +Examples: + +gpio-restart { + compatible = "gpio-restart"; + gpios = <&gpio 4 0>; + priority = <128>; + active-delay = <100>; + inactive-delay = <100>; + wait-delay = <3000>; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-samsung.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-samsung.txt new file mode 100644 index 000000000..5375625e8 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-samsung.txt @@ -0,0 +1,41 @@ +Samsung Exynos4 GPIO Controller + +Required properties: +- compatible: Compatible property value should be "samsung,exynos4-gpio>". + +- reg: Physical base address of the controller and length of memory mapped + region. + +- #gpio-cells: Should be 4. The syntax of the gpio specifier used by client nodes + should be the following with values derived from the SoC user manual. + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [mux function] + [flags and pull up/down] + [drive strength]> + + Values for gpio specifier: + - Pin number: is a value between 0 to 7. + - Flags and Pull Up/Down: 0 - Pull Up/Down Disabled. + 1 - Pull Down Enabled. + 3 - Pull Up Enabled. + Bit 16 (0x00010000) - Input is active low. + - Drive Strength: 0 - 1x, + 1 - 3x, + 2 - 2x, + 3 - 4x + +- gpio-controller: Specifies that the node is a gpio controller. +- #address-cells: should be 1. +- #size-cells: should be 1. + +Example: + + gpa0: gpio-controller@11400000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "samsung,exynos4-gpio"; + reg = <0x11400000 0x20>; + #gpio-cells = <4>; + gpio-controller; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-stericsson-coh901.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-stericsson-coh901.txt new file mode 100644 index 000000000..fd665b44d --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-stericsson-coh901.txt @@ -0,0 +1,7 @@ +ST-Ericsson COH 901 571/3 GPIO controller + +Required properties: +- compatible: Compatible property value should be "stericsson,gpio-coh901" +- reg: Physical base address of the controller and length of memory mapped + region. +- interrupts: the 0...n interrupts assigned to the different GPIO ports/banks. diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt new file mode 100644 index 000000000..a0e4cf885 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-stmpe.txt @@ -0,0 +1,18 @@ +STMPE gpio +---------- + +Required properties: + - compatible: "st,stmpe-gpio" + +Optional properties: + - st,norequest-mask: bitmask specifying which GPIOs should _not_ be requestable + due to different usage (e.g. touch, keypad) + +Node name must be stmpe_gpio and should be child node of stmpe node to which it +belongs. + +Example: + stmpe_gpio { + compatible = "st,stmpe-gpio"; + st,norequest-mask = <0x20>; //gpio 5 can't be used + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt new file mode 100644 index 000000000..854de130a --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt @@ -0,0 +1,42 @@ +Lantiq SoC Serial To Parallel (STP) GPIO controller + +The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a +peripheral controller used to drive external shift register cascades. At most +3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem +to drive the 2 LSBs of the cascade automatically. + + +Required properties: +- compatible : Should be "lantiq,gpio-stp-xway" +- reg : Address and length of the register set for the device +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters (currently + unused). +- gpio-controller : Marks the device node as a gpio controller. + +Optional properties: +- lantiq,shadow : The default value that we shall assume as already set on the + shift register cascade. +- lantiq,groups : Set the 3 bit mask to select which of the 3 groups are enabled + in the shift register cascade. +- lantiq,dsl : The dsl core can control the 2 LSBs of the gpio cascade. This 2 bit + property can enable this feature. +- lantiq,phy1 : The gphy1 core can control 3 bits of the gpio cascade. +- lantiq,phy2 : The gphy2 core can control 3 bits of the gpio cascade. +- lantiq,rising : use rising instead of falling edge for the shift register + +Example: + +gpio1: stp@E100BB0 { + compatible = "lantiq,gpio-stp-xway"; + reg = <0xE100BB0 0x40>; + #gpio-cells = <2>; + gpio-controller; + + lantiq,shadow = <0xffff>; + lantiq,groups = <0x7>; + lantiq,dsl = <0x3>; + lantiq,phy1 = <0x7>; + lantiq,phy2 = <0x7>; + /* lantiq,rising; */ +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt new file mode 100644 index 000000000..ba2bb84ee --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-sx150x.txt @@ -0,0 +1,40 @@ +SEMTECH SX150x GPIO expander bindings + + +Required properties: + +- compatible: should be "semtech,sx1506q", + "semtech,sx1508q", + "semtech,sx1509q". + +- reg: The I2C slave address for this device. + +- interrupt-parent: phandle of the parent interrupt controller. + +- interrupts: Interrupt specifier for the controllers interrupt. + +- #gpio-cells: Should be 2. The first cell is the GPIO number and the + second cell is used to specify optional parameters: + bit 0: polarity (0: normal, 1: inverted) + +- gpio-controller: Marks the device as a GPIO controller. + +- interrupt-controller: Marks the device as a interrupt controller. + +The GPIO expander can optionally be used as an interrupt controller, in +which case it uses the default two cell specifier as described in +Documentation/devicetree/bindings/interrupt-controller/interrupts.txt. + +Example: + + i2c_gpio_expander@20{ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "semtech,sx1506q"; + reg = <0x20>; + interrupt-parent = <&gpio_1>; + interrupts = <16 0>; + + gpio-controller; + interrupt-controller; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt new file mode 100644 index 000000000..66788fda1 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt @@ -0,0 +1,29 @@ +twl4030 GPIO controller bindings + +Required properties: +- compatible: + - "ti,twl4030-gpio" for twl4030 GPIO controller +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify optional parameters (unused) +- gpio-controller : Marks the device node as a GPIO controller. +- #interrupt-cells : Should be 2. +- interrupt-controller: Mark the device node as an interrupt controller + The first cell is the GPIO number. + The second cell is not used. +- ti,use-leds : Enables LEDA and LEDB outputs if set +- ti,debounce : if n-th bit is set, debounces GPIO-n +- ti,mmc-cd : if n-th bit is set, GPIO-n controls VMMC(n+1) +- ti,pullups : if n-th bit is set, set a pullup on GPIO-n +- ti,pulldowns : if n-th bit is set, set a pulldown on GPIO-n + +Example: + +twl_gpio: gpio { + compatible = "ti,twl4030-gpio"; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; + ti,use-leds; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-tz1090-pdc.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-tz1090-pdc.txt new file mode 100644 index 000000000..1fd98ffa8 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-tz1090-pdc.txt @@ -0,0 +1,45 @@ +ImgTec TZ1090 PDC GPIO Controller + +Required properties: +- compatible: Compatible property value should be "img,tz1090-pdc-gpio". + +- reg: Physical base address of the controller and length of memory mapped + region. This starts at and cover the SOC_GPIO_CONTROL registers. + +- gpio-controller: Specifies that the node is a gpio controller. + +- #gpio-cells: Should be 2. The syntax of the gpio specifier used by client + nodes should have the following values. + <[phandle of the gpio controller node] + [PDC gpio number] + [gpio flags]> + + Values for gpio specifier: + - GPIO number: a value in the range 0 to 6. + - GPIO flags: bit field of flags, as defined in . + Only the following flags are supported: + GPIO_ACTIVE_HIGH + GPIO_ACTIVE_LOW + +Optional properties: +- gpio-ranges: Mapping to pin controller pins (as described in + Documentation/devicetree/bindings/gpio/gpio.txt) + +- interrupts: Individual syswake interrupts (other GPIOs cannot interrupt) + + +Example: + + pdc_gpios: gpio-controller@02006500 { + gpio-controller; + #gpio-cells = <2>; + + compatible = "img,tz1090-pdc-gpio"; + reg = <0x02006500 0x100>; + + interrupt-parent = <&pdc>; + interrupts = <8 IRQ_TYPE_NONE>, /* Syswake 0 */ + <9 IRQ_TYPE_NONE>, /* Syswake 1 */ + <10 IRQ_TYPE_NONE>; /* Syswake 2 */ + gpio-ranges = <&pdc_pinctrl 0 0 7>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-tz1090.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-tz1090.txt new file mode 100644 index 000000000..174cdf309 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-tz1090.txt @@ -0,0 +1,88 @@ +ImgTec TZ1090 GPIO Controller + +Required properties: +- compatible: Compatible property value should be "img,tz1090-gpio". + +- reg: Physical base address of the controller and length of memory mapped + region. + +- #address-cells: Should be 1 (for bank subnodes) + +- #size-cells: Should be 0 (for bank subnodes) + +- Each bank of GPIOs should have a subnode to represent it. + + Bank subnode required properties: + - reg: Index of bank in the range 0 to 2. + + - gpio-controller: Specifies that the node is a gpio controller. + + - #gpio-cells: Should be 2. The syntax of the gpio specifier used by client + nodes should have the following values. + <[phandle of the gpio controller node] + [gpio number within the gpio bank] + [gpio flags]> + + Values for gpio specifier: + - GPIO number: a value in the range 0 to 29. + - GPIO flags: bit field of flags, as defined in . + Only the following flags are supported: + GPIO_ACTIVE_HIGH + GPIO_ACTIVE_LOW + + Bank subnode optional properties: + - gpio-ranges: Mapping to pin controller pins (as described in + Documentation/devicetree/bindings/gpio/gpio.txt) + + - interrupts: Interrupt for the entire bank + + - interrupt-controller: Specifies that the node is an interrupt controller + + - #interrupt-cells: Should be 2. The syntax of the interrupt specifier used by + client nodes should have the following values. + <[phandle of the interurupt controller] + [gpio number within the gpio bank] + [irq flags]> + + Values for irq specifier: + - GPIO number: a value in the range 0 to 29 + - IRQ flags: value to describe edge and level triggering, as defined in + . Only the following flags are + supported: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + IRQ_TYPE_LEVEL_HIGH + IRQ_TYPE_LEVEL_LOW + + + +Example: + + gpios: gpio-controller@02005800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "img,tz1090-gpio"; + reg = <0x02005800 0x90>; + + /* bank 0 with an interrupt */ + gpios0: bank@0 { + #gpio-cells = <2>; + #interrupt-cells = <2>; + reg = <0>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + gpio-ranges = <&pinctrl 0 0 30>; + interrupt-controller; + }; + + /* bank 2 without interrupt */ + gpios2: bank@2 { + #gpio-cells = <2>; + reg = <2>; + gpio-controller; + gpio-ranges = <&pinctrl 0 60 30>; + }; + }; + + diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-vf610.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-vf610.txt new file mode 100644 index 000000000..436cc99c6 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-vf610.txt @@ -0,0 +1,55 @@ +* Freescale VF610 PORT/GPIO module + +The Freescale PORT/GPIO modules are two adjacent modules providing GPIO +functionality. Each pair serves 32 GPIOs. The VF610 has 5 instances of +each, and each PORT module has its own interrupt. + +Required properties for GPIO node: +- compatible : Should be "fsl,-gpio", currently "fsl,vf610-gpio" +- reg : The first reg tuple represents the PORT module, the second tuple + the GPIO module. +- interrupts : Should be the port interrupt shared by all 32 pins. +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells : Should be 2. The first cell is the GPIO number. + The second cell bits[3:0] is used to specify trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + +Note: Each GPIO port should have an alias correctly numbered in "aliases" +node. + +Examples: + +aliases { + gpio0 = &gpio1; + gpio1 = &gpio2; +}; + +gpio1: gpio@40049000 { + compatible = "fsl,vf610-gpio"; + reg = <0x40049000 0x1000 0x400ff000 0x40>; + interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 0 32>; +}; + +gpio2: gpio@4004a000 { + compatible = "fsl,vf610-gpio"; + reg = <0x4004a000 0x1000 0x400ff040 0x40>; + interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 32 32>; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt new file mode 100644 index 000000000..dae130060 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt @@ -0,0 +1,32 @@ +APM X-Gene Standby GPIO controller bindings + +This is a gpio controller in the standby domain. + +There are 20 GPIO pins from 0..21. There is no GPIO_DS14 or GPIO_DS15, +only GPIO_DS8..GPIO_DS13 support interrupts. The IRQ mapping +is currently 1-to-1 on interrupts 0x28 thru 0x2d. + +Required properties: +- compatible: "apm,xgene-gpio-sb" for the X-Gene Standby GPIO controller +- reg: Physical base address and size of the controller's registers +- #gpio-cells: Should be two. + - first cell is the pin number + - second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- gpio-controller: Marks the device node as a GPIO controller. +- interrupts: Shall contain exactly 6 interrupts. + +Example: + sbgpio: sbgpio@17001000 { + compatible = "apm,xgene-gpio-sb"; + reg = <0x0 0x17001000 0x0 0x400>; + #gpio-cells = <2>; + gpio-controller; + interrupts = <0x0 0x28 0x1>, + <0x0 0x29 0x1>, + <0x0 0x2a 0x1>, + <0x0 0x2b 0x1>, + <0x0 0x2c 0x1>, + <0x0 0x2d 0x1>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-xgene.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-xgene.txt new file mode 100644 index 000000000..86dbb05e7 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-xgene.txt @@ -0,0 +1,22 @@ +APM X-Gene SoC GPIO controller bindings + +This is a gpio controller that is part of the flash controller. +This gpio controller controls a total of 48 gpios. + +Required properties: +- compatible: "apm,xgene-gpio" for X-Gene GPIO controller +- reg: Physical base address and size of the controller's registers +- #gpio-cells: Should be two. + - first cell is the pin number + - second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- gpio-controller: Marks the device node as a GPIO controller. + +Example: + gpio0: gpio0@1701c000 { + compatible = "apm,xgene-gpio"; + reg = <0x0 0x1701c000 0x0 0x40>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt new file mode 100644 index 000000000..63bf4becd --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt @@ -0,0 +1,48 @@ +Xilinx plb/axi GPIO controller + +Dual channel GPIO controller with configurable number of pins +(from 1 to 32 per channel). Every pin can be configured as +input/output/tristate. Both channels share the same global IRQ but +local interrupts can be enabled on channel basis. + +Required properties: +- compatible : Should be "xlnx,xps-gpio-1.00.a" +- reg : Address and length of the register set for the device +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller : Marks the device node as a GPIO controller. + +Optional properties: +- interrupts : Interrupt mapping for GPIO IRQ. +- interrupt-parent : Phandle for the interrupt controller that + services interrupts for this device. +- xlnx,all-inputs : if n-th bit is setup, GPIO-n is input +- xlnx,dout-default : if n-th bit is 1, GPIO-n default value is 1 +- xlnx,gpio-width : gpio width +- xlnx,tri-default : if n-th bit is 1, GPIO-n is in tristate mode +- xlnx,is-dual : if 1, controller also uses the second channel +- xlnx,all-inputs-2 : as above but for the second channel +- xlnx,dout-default-2 : as above but the second channel +- xlnx,gpio2-width : as above but for the second channel +- xlnx,tri-default-2 : as above but for the second channel + + +Example: +gpio: gpio@40000000 { + #gpio-cells = <2>; + compatible = "xlnx,xps-gpio-1.00.a"; + gpio-controller ; + interrupt-parent = <µblaze_0_intc>; + interrupts = < 6 2 >; + reg = < 0x40000000 0x10000 >; + xlnx,all-inputs = <0x0>; + xlnx,all-inputs-2 = <0x0>; + xlnx,dout-default = <0x0>; + xlnx,dout-default-2 = <0x0>; + xlnx,gpio-width = <0x2>; + xlnx,gpio2-width = <0x2>; + xlnx,interrupt-present = <0x1>; + xlnx,is-dual = <0x1>; + xlnx,tri-default = <0xffffffff>; + xlnx,tri-default-2 = <0xffffffff>; +} ; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-zevio.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-zevio.txt new file mode 100644 index 000000000..a37bd9ae2 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-zevio.txt @@ -0,0 +1,16 @@ +Zevio GPIO controller + +Required properties: +- compatible: Should be "lsi,zevio-gpio" +- reg: Address and length of the register set for the device +- #gpio-cells: Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller: Marks the device node as a GPIO controller. + +Example: + gpio: gpio@90000000 { + compatible = "lsi,zevio-gpio"; + reg = <0x90000000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio-zynq.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio-zynq.txt new file mode 100644 index 000000000..986371a4b --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio-zynq.txt @@ -0,0 +1,26 @@ +Xilinx Zynq GPIO controller Device Tree Bindings +------------------------------------------- + +Required properties: +- #gpio-cells : Should be two + - First cell is the GPIO line number + - Second cell is used to specify optional + parameters (unused) +- compatible : Should be "xlnx,zynq-gpio-1.0" +- clocks : Clock specifier (see clock bindings for details) +- gpio-controller : Marks the device node as a GPIO controller. +- interrupts : Interrupt specifier (see interrupt bindings for + details) +- interrupt-parent : Must be core interrupt controller +- reg : Address and length of the register set for the device + +Example: + gpio@e000a000 { + #gpio-cells = <2>; + compatible = "xlnx,zynq-gpio-1.0"; + clocks = <&clkc 42>; + gpio-controller; + interrupt-parent = <&intc>; + interrupts = <0 20 4>; + reg = <0xe000a000 0x1000>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio.txt new file mode 100644 index 000000000..5788d5cf1 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio.txt @@ -0,0 +1,242 @@ +Specifying GPIO information for devices +============================================ + +1) gpios property +----------------- + +Nodes that makes use of GPIOs should specify them using one or more +properties, each containing a 'gpio-list': + + gpio-list ::= [gpio-list] + single-gpio ::= + gpio-phandle : phandle to gpio controller node + gpio-specifier : Array of #gpio-cells specifying specific gpio + (controller specific) + +GPIO properties should be named "[-]gpios", with being the purpose +of this GPIO for the device. While a non-existent is considered valid +for compatibility reasons (resolving to the "gpios" property), it is not allowed +for new bindings. + +GPIO properties can contain one or more GPIO phandles, but only in exceptional +cases should they contain more than one. If your device uses several GPIOs with +distinct functions, reference each of them under its own property, giving it a +meaningful name. The only case where an array of GPIOs is accepted is when +several GPIOs serve the same function (e.g. a parallel data line). + +The exact purpose of each gpios property must be documented in the device tree +binding of the device. + +The following example could be used to describe GPIO pins used as device enable +and bit-banged data signals: + + gpio1: gpio1 { + gpio-controller + #gpio-cells = <2>; + }; + gpio2: gpio2 { + gpio-controller + #gpio-cells = <1>; + }; + [...] + + enable-gpios = <&gpio2 2>; + data-gpios = <&gpio1 12 0>, + <&gpio1 13 0>, + <&gpio1 14 0>, + <&gpio1 15 0>; + +Note that gpio-specifier length is controller dependent. In the +above example, &gpio1 uses 2 cells to specify a gpio, while &gpio2 +only uses one. + +gpio-specifier may encode: bank, pin position inside the bank, +whether pin is open-drain and whether pin is logically inverted. +Exact meaning of each specifier cell is controller specific, and must +be documented in the device tree binding for the device. Use the macros +defined in include/dt-bindings/gpio/gpio.h whenever possible: + +Example of a node using GPIOs: + + node { + enable-gpios = <&qe_pio_e 18 GPIO_ACTIVE_HIGH>; + }; + +GPIO_ACTIVE_HIGH is 0, so in this example gpio-specifier is "18 0" and encodes +GPIO pin number, and GPIO flags as accepted by the "qe_pio_e" gpio-controller. + +1.1) GPIO specifier best practices +---------------------------------- + +A gpio-specifier should contain a flag indicating the GPIO polarity; active- +high or active-low. If it does, the following best practices should be +followed: + +The gpio-specifier's polarity flag should represent the physical level at the +GPIO controller that achieves (or represents, for inputs) a logically asserted +value at the device. The exact definition of logically asserted should be +defined by the binding for the device. If the board inverts the signal between +the GPIO controller and the device, then the gpio-specifier will represent the +opposite physical level than the signal at the device's pin. + +When the device's signal polarity is configurable, the binding for the +device must either: + +a) Define a single static polarity for the signal, with the expectation that +any software using that binding would statically program the device to use +that signal polarity. + +The static choice of polarity may be either: + +a1) (Preferred) Dictated by a binding-specific DT property. + +or: + +a2) Defined statically by the DT binding itself. + +In particular, the polarity cannot be derived from the gpio-specifier, since +that would prevent the DT from separately representing the two orthogonal +concepts of configurable signal polarity in the device, and possible board- +level signal inversion. + +or: + +b) Pick a single option for device signal polarity, and document this choice +in the binding. The gpio-specifier should represent the polarity of the signal +(at the GPIO controller) assuming that the device is configured for this +particular signal polarity choice. If software chooses to program the device +to generate or receive a signal of the opposite polarity, software will be +responsible for correctly interpreting (inverting) the GPIO signal at the GPIO +controller. + +2) gpio-controller nodes +------------------------ + +Every GPIO controller node must contain both an empty "gpio-controller" +property, and a #gpio-cells integer property, which indicates the number of +cells in a gpio-specifier. + +The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism +providing automatic GPIO request and configuration as part of the +gpio-controller's driver probe function. + +Each GPIO hog definition is represented as a child node of the GPIO controller. +Required properties: +- gpio-hog: A property specifying that this child node represent a GPIO hog. +- gpios: Store the GPIO information (id, flags, ...). Shall contain the + number of cells specified in its parent node (GPIO controller + node). +Only one of the following properties scanned in the order shown below. +This means that when multiple properties are present they will be searched +in the order presented below and the first match is taken as the intended +configuration. +- input: A property specifying to set the GPIO direction as input. +- output-low A property specifying to set the GPIO direction as output with + the value low. +- output-high A property specifying to set the GPIO direction as output with + the value high. + +Optional properties: +- line-name: The GPIO label name. If not present the node name is used. + +Example of two SOC GPIO banks defined as gpio-controller nodes: + + qe_pio_a: gpio-controller@1400 { + compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank"; + reg = <0x1400 0x18>; + gpio-controller; + #gpio-cells = <2>; + + line_b { + gpio-hog; + gpios = <6 0>; + output-low; + line-name = "foo-bar-gpio"; + }; + }; + + qe_pio_e: gpio-controller@1460 { + compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + #gpio-cells = <2>; + }; + +2.1) gpio- and pin-controller interaction +----------------------------------------- + +Some or all of the GPIOs provided by a GPIO controller may be routed to pins +on the package via a pin controller. This allows muxing those pins between +GPIO and other functions. + +It is useful to represent which GPIOs correspond to which pins on which pin +controllers. The gpio-ranges property described below represents this, and +contains information structures as follows: + + gpio-range-list ::= [gpio-range-list] + single-gpio-range ::= | + numeric-gpio-range ::= + + named-gpio-range ::= '<0 0>' + pinctrl-phandle : phandle to pin controller node + gpio-base : Base GPIO ID in the GPIO controller + pinctrl-base : Base pinctrl pin ID in the pin controller + count : The number of GPIOs/pins in this range + +The "pin controller node" mentioned above must conform to the bindings +described in ../pinctrl/pinctrl-bindings.txt. + +In case named gpio ranges are used (ranges with both and + set to 0), the property gpio-ranges-group-names contains one string +for every single-gpio-range in gpio-ranges: + gpiorange-names-list ::= [gpiorange-names-list] + gpiorange-name : Name of the pingroup associated to the GPIO range in + the respective pin controller. + +Elements of gpiorange-names-list corresponding to numeric ranges contain +the empty string. Elements of gpiorange-names-list corresponding to named +ranges contain the name of a pin group defined in the respective pin +controller. The number of pins/GPIOs in the range is the number of pins in +that pin group. + +Previous versions of this binding required all pin controller nodes that +were referenced by any gpio-ranges property to contain a property named +#gpio-range-cells with value <3>. This requirement is now deprecated. +However, that property may still exist in older device trees for +compatibility reasons, and would still be required even in new device +trees that need to be compatible with older software. + +Example 1: + + qe_pio_e: gpio-controller@1460 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; + reg = <0x1460 0x18>; + gpio-controller; + gpio-ranges = <&pinctrl1 0 20 10>, <&pinctrl2 10 50 20>; + }; + +Here, a single GPIO controller has GPIOs 0..9 routed to pin controller +pinctrl1's pins 20..29, and GPIOs 10..19 routed to pin controller pinctrl2's +pins 50..59. + +Example 2: + + gpio_pio_i: gpio-controller@14B0 { + #gpio-cells = <2>; + compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; + reg = <0x1480 0x18>; + gpio-controller; + gpio-ranges = <&pinctrl1 0 20 10>, + <&pinctrl2 10 0 0>, + <&pinctrl1 15 0 10>, + <&pinctrl2 25 0 0>; + gpio-ranges-group-names = "", + "foo", + "", + "bar"; + }; + +Here, three GPIO ranges are defined wrt. two pin controllers. pinctrl1 GPIO +ranges are defined using pin numbers whereas the GPIO ranges wrt. pinctrl2 +are named "foo" and "bar". diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio_atmel.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio_atmel.txt new file mode 100644 index 000000000..85f8c0d08 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio_atmel.txt @@ -0,0 +1,25 @@ +* Atmel GPIO controller (PIO) + +Required properties: +- compatible: "atmel,-gpio", where is at91rm9200 or at91sam9x5. +- reg: Should contain GPIO controller registers location and length +- interrupts: Should be the port interrupt shared by all the pins. +- #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify optional parameters (currently + unused). +- gpio-controller: Marks the device node as a GPIO controller. + +optional properties: +- #gpio-lines: Number of gpio if absent 32. + + +Example: + pioA: gpio@fffff200 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff200 0x100>; + interrupts = <2 4>; + #gpio-cells = <2>; + gpio-controller; + #gpio-lines = <19>; + }; + diff --git a/kernel/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt b/kernel/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt new file mode 100644 index 000000000..49819367a --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt @@ -0,0 +1,43 @@ +NXP LPC32xx SoC GPIO controller + +Required properties: +- compatible: must be "nxp,lpc3220-gpio" +- reg: Physical base address and length of the controller's registers. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be 3: + 1) bank: + 0: GPIO P0 + 1: GPIO P1 + 2: GPIO P2 + 3: GPIO P3 + 4: GPI P3 + 5: GPO P3 + 2) pin number + 3) optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) +- reg: Index of the GPIO group + +Example: + + gpio: gpio@40028000 { + compatible = "nxp,lpc3220-gpio"; + reg = <0x40028000 0x1000>; + gpio-controller; + #gpio-cells = <3>; /* bank, pin, flags */ + }; + + leds { + compatible = "gpio-leds"; + + led0 { + gpios = <&gpio 5 1 1>; /* GPO_P3 1, active low */ + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led1 { + gpios = <&gpio 5 14 1>; /* GPO_P3 14, active low */ + linux,default-trigger = "timer"; + default-state = "off"; + }; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/moxa,moxart-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/moxa,moxart-gpio.txt new file mode 100644 index 000000000..f8e8f185a --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/moxa,moxart-gpio.txt @@ -0,0 +1,19 @@ +MOXA ART GPIO Controller + +Required properties: + +- #gpio-cells : Should be 2, The first cell is the pin number, + the second cell is used to specify polarity: + 0 = active high + 1 = active low +- compatible : Must be "moxa,moxart-gpio" +- reg : Should contain registers location and length + +Example: + + gpio: gpio@98700000 { + gpio-controller; + #gpio-cells = <2>; + compatible = "moxa,moxart-gpio"; + reg = <0x98700000 0xC>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt new file mode 100644 index 000000000..98d198396 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -0,0 +1,69 @@ +* Marvell PXA GPIO controller + +Required properties: +- compatible : Should be "intel,pxa25x-gpio", "intel,pxa26x-gpio", + "intel,pxa27x-gpio", "intel,pxa3xx-gpio", + "marvell,pxa93x-gpio", "marvell,mmp-gpio", + "marvell,mmp2-gpio" or marvell,pxa1928-gpio. +- reg : Address and length of the register set for the device +- interrupts : Should be the port interrupt shared by all gpio pins. + There're three gpio interrupts in arch-pxa, and they're gpio0, + gpio1 and gpio_mux. There're only one gpio interrupt in arch-mmp, + gpio_mux. +- interrupt-names : Should be the names of irq resources. Each interrupt + uses its own interrupt name, so there should be as many interrupt names + as referenced interrupts. +- interrupt-controller : Identifies the node as an interrupt controller. +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be one. It is the pin number. + +Example for a MMP platform: + + gpio: gpio@d4019000 { + compatible = "marvell,mmp-gpio"; + reg = <0xd4019000 0x1000>; + interrupts = <49>; + interrupt-names = "gpio_mux"; + gpio-controller; + #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <1>; + }; + +Example for a PXA3xx platform: + + gpio: gpio@40e00000 { + compatible = "intel,pxa3xx-gpio"; + reg = <0x40e00000 0x10000>; + interrupt-names = "gpio0", "gpio1", "gpio_mux"; + interrupts = <8 9 10>; + gpio-controller; + #gpio-cells = <0x2>; + interrupt-controller; + #interrupt-cells = <0x2>; + }; + +* Marvell Orion GPIO Controller + +Required properties: +- compatible : Should be "marvell,orion-gpio" +- reg : Address and length of the register set for controller. +- gpio-controller : So we know this is a gpio controller. +- ngpio : How many gpios this controller has. +- interrupts : Up to 4 Interrupts for the controller. + +Optional properties: +- mask-offset : For SMP Orions, offset for Nth CPU + +Example: + + gpio0: gpio@10100 { + compatible = "marvell,orion-gpio"; + #gpio-cells = <2>; + gpio-controller; + reg = <0x10100 0x40>; + ngpio = <32>; + interrupts = <35>, <36>, <37>, <38>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.txt new file mode 100644 index 000000000..023c9526e --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.txt @@ -0,0 +1,40 @@ +NVIDIA Tegra GPIO controller + +Required properties: +- compatible : "nvidia,tegra-gpio" +- reg : Physical base address and length of the controller's registers. +- interrupts : The interrupt outputs from the controller. For Tegra20, + there should be 7 interrupts specified, and for Tegra30, there should + be 8 interrupts specified. +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) +- gpio-controller : Marks the device node as a GPIO controller. +- #interrupt-cells : Should be 2. + The first cell is the GPIO number. + The second cell is used to specify flags: + bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. + Valid combinations are 1, 2, 3, 4, 8. +- interrupt-controller : Marks the device node as an interrupt controller. + +Example: + +gpio: gpio@6000d000 { + compatible = "nvidia,tegra20-gpio"; + reg = < 0x6000d000 0x1000 >; + interrupts = < 0 32 0x04 + 0 33 0x04 + 0 34 0x04 + 0 35 0x04 + 0 55 0x04 + 0 87 0x04 + 0 89 0x04 >; + #gpio-cells = <2>; + gpio-controller; + #interrupt-cells = <2>; + interrupt-controller; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/pl061-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/pl061-gpio.txt new file mode 100644 index 000000000..89058d375 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/pl061-gpio.txt @@ -0,0 +1,10 @@ +ARM PL061 GPIO controller + +Required properties: +- compatible : "arm,pl061", "arm,primecell" +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) +- gpio-controller : Marks the device node as a GPIO controller. +- interrupts : Interrupt mapping for GPIO IRQ. +- gpio-ranges : Interaction with the PINCTRL subsystem. diff --git a/kernel/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/kernel/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt new file mode 100644 index 000000000..38fb86f28 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -0,0 +1,63 @@ +* Renesas R-Car GPIO Controller + +Required Properties: + + - compatible: should contain one of the following. + - "renesas,gpio-r8a7778": for R8A7778 (R-Mobile M1) compatible GPIO controller. + - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller. + - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller. + - "renesas,gpio-r8a7791": for R8A7791 (R-Car M2-W) compatible GPIO controller. + - "renesas,gpio-r8a7793": for R8A7793 (R-Car M2-N) compatible GPIO controller. + - "renesas,gpio-r8a7794": for R8A7794 (R-Car E2) compatible GPIO controller. + - "renesas,gpio-rcar": for generic R-Car GPIO controller. + + - reg: Base address and length of each memory resource used by the GPIO + controller hardware module. + + - interrupt-parent: phandle of the parent interrupt controller. + - interrupts: Interrupt specifier for the controllers interrupt. + + - gpio-controller: Marks the device node as a gpio controller. + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in . Only the + GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. + - gpio-ranges: Range of pins managed by the GPIO controller. + +Optional properties: + + - clocks: Must contain a reference to the functional clock. The property is + mandatory if the hardware implements a controllable functional clock for + the GPIO instance. + +Please refer to gpio.txt in this directory for details of gpio-ranges property +and the common GPIO bindings used by client devices. + +The GPIO controller also acts as an interrupt controller. It uses the default +two cells specifier as described in Documentation/devicetree/bindings/ +interrupt-controller/interrupts.txt. + +Example: R8A7779 (R-Car H1) GPIO controller nodes + + gpio0: gpio@ffc40000 { + compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar"; + reg = <0xffc40000 0x2c>; + interrupt-parent = <&gic>; + interrupts = <0 141 0x4>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 0 32>; + interrupt-controller; + #interrupt-cells = <2>; + }; + ... + gpio6: gpio@ffc46000 { + compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar"; + reg = <0xffc46000 0x2c>; + interrupt-parent = <&gic>; + interrupts = <0 147 0x4>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 192 9>; + interrupt-controller; + #interrupt-cells = <2>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt b/kernel/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt new file mode 100644 index 000000000..dd5d2c039 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt @@ -0,0 +1,60 @@ +* Synopsys DesignWare APB GPIO controller + +Required properties: +- compatible : Should contain "snps,dw-apb-gpio" +- reg : Address and length of the register set for the device. +- #address-cells : should be 1 (for addressing port subnodes). +- #size-cells : should be 0 (port subnodes). + +The GPIO controller has a configurable number of ports, each of which are +represented as child nodes with the following properties: + +Required properties: +- compatible : "snps,dw-apb-gpio-port" +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- reg : The integer port index of the port, a single cell. + +Optional properties: +- interrupt-controller : The first port may be configured to be an interrupt +controller. +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt. Shall be set to 2. The first cell defines the interrupt number, + the second encodes the triger flags encoded as described in + Documentation/devicetree/bindings/interrupts.txt +- interrupt-parent : The parent interrupt controller. +- interrupts : The interrupt to the parent controller raised when GPIOs + generate the interrupts. +- snps,nr-gpios : The number of pins in the port, a single cell. + +Example: + +gpio: gpio@20000 { + compatible = "snps,dw-apb-gpio"; + reg = <0x20000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porta: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <8>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&vic1>; + interrupts = <0>; + }; + + portb: gpio-controller@1 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <8>; + reg = <1>; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/gpio/sodaville.txt b/kernel/Documentation/devicetree/bindings/gpio/sodaville.txt new file mode 100644 index 000000000..563eff22b --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/sodaville.txt @@ -0,0 +1,48 @@ +GPIO controller on CE4100 / Sodaville SoCs +========================================== + +The bindings for CE4100's GPIO controller match the generic description +which is covered by the gpio.txt file in this folder. + +The only additional property is the intel,muxctl property which holds the +value which is written into the MUXCNTL register. + +There is no compatible property for now because the driver is probed via +PCI id (vendor 0x8086 device 0x2e67). + +The interrupt specifier consists of two cells encoded as follows: + - <1st cell>: The interrupt-number that identifies the interrupt source. + - <2nd cell>: The level-sense information, encoded as follows: + 4 - active high level-sensitive + 8 - active low level-sensitive + +Example of the GPIO device and one user: + + pcigpio: gpio@b,1 { + /* two cells for GPIO and interrupt */ + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "pci8086,2e67.2", + "pci8086,2e67", + "pciclassff0000", + "pciclassff00"; + + reg = <0x15900 0x0 0x0 0x0 0x0>; + /* Interrupt line of the gpio device */ + interrupts = <15 1>; + /* It is an interrupt and GPIO controller itself */ + interrupt-controller; + gpio-controller; + intel,muxctl = <0>; + }; + + testuser@20 { + compatible = "example,testuser"; + /* User the 11th GPIO line as an active high triggered + * level interrupt + */ + interrupts = <11 8>; + interrupt-parent = <&pcigpio>; + /* Use this GPIO also with the gpio functions */ + gpios = <&pcigpio 11 0>; + }; diff --git a/kernel/Documentation/devicetree/bindings/gpio/spear_spics.txt b/kernel/Documentation/devicetree/bindings/gpio/spear_spics.txt new file mode 100644 index 000000000..96c37eb15 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/gpio/spear_spics.txt @@ -0,0 +1,50 @@ +=== ST Microelectronics SPEAr SPI CS Driver === + +SPEAr platform provides a provision to control chipselects of ARM PL022 Prime +Cell spi controller through its system registers, which otherwise remains under +PL022 control. If chipselect remain under PL022 control then they would be +released as soon as transfer is over and TxFIFO becomes empty. This is not +desired by some of the device protocols above spi which expect (multiple) +transfers without releasing their chipselects. + +Chipselects can be controlled by software by turning them as GPIOs. SPEAr +provides another interface through system registers through which software can +directly control each PL022 chipselect. Hence, it is natural for SPEAr to export +the control of this interface as gpio. + +Required properties: + + * compatible: should be defined as "st,spear-spics-gpio" + * reg: mentioning address range of spics controller + * st-spics,peripcfg-reg: peripheral configuration register offset + * st-spics,sw-enable-bit: bit offset to enable sw control + * st-spics,cs-value-bit: bit offset to drive chipselect low or high + * st-spics,cs-enable-mask: chip select number bit mask + * st-spics,cs-enable-shift: chip select number program offset + * gpio-controller: Marks the device node as gpio controller + * #gpio-cells: should be 1 and will mention chip select number + +All the above bit offsets are within peripcfg register. + +Example: +------- +spics: spics@e0700000{ + compatible = "st,spear-spics-gpio"; + reg = <0xe0700000 0x1000>; + st-spics,peripcfg-reg = <0x3b0>; + st-spics,sw-enable-bit = <12>; + st-spics,cs-value-bit = <11>; + st-spics,cs-enable-mask = <3>; + st-spics,cs-enable-shift = <8>; + gpio-controller; + #gpio-cells = <2>; +}; + + +spi0: spi@e0100000 { + status = "okay"; + num-cs = <3>; + cs-gpios = <&gpio1 7 0>, <&spics 0>, + <&spics 1>; + ... +} -- cgit 1.2.3-korg