1 files changed, 62 insertions, 0 deletions
diff --git a/functest/opnfv_tests/vnf/epc/featureFiles/Auth_NotAccept_by_Network_IMSIattach_AuthReject_re_Auth.feature b/functest/opnfv_tests/vnf/epc/featureFiles/Auth_NotAccept_by_Network_IMSIattach_AuthReject_re_Auth.feature
new file mode 100644
index 000000000..cce93f426
--- /dev/null
+++ b/functest/opnfv_tests/vnf/epc/featureFiles/Auth_NotAccept_by_Network_IMSIattach_AuthReject_re_Auth.feature
@@ -0,0 +1,62 @@
+    ############################################################################################################################
+    #                                              Date: <22/11/2016> Version: <1.1>                                           #
+    ############################################################################################################################
+
+    Feature:Auth_NotAccept_by_Network_IMSIattach_AuthReject_re_Auth
+
+    @authentication-procedure @Auth_NotAccept_by_Network_IMSIattach_AuthReject_re_Auth @TS_24_301 @24_301_5_3_3 @24_301_5_5_1_2_2 @24_301_5_5_1_2_4 @24_301_6_5_1_2 @24_301_9_9_3_33 @TS_36_304 @36_304_4_3 @negTCs @Series-0001
+
+    Scenario: Authentication not accepted by the network when attach with IMSI, Authentication reject when RES is different from UE and MME
+
+    Given all configured endpoints for SSH are connected successfully
+
+    Given the steps below will be executed at the end
+    When I stop S1AP simulator on node ABOT
+    When I run the SSH command "sudo service mme_gw restart" on node MME
+    #RES is restore to 0x00 in teardown process
+    Given that I setup S1AP Simulator with UE parameter "ABOT.UE.CONFIG.SECURITY.RES=0x00" on node ABOT
+    Given the execution is paused for {abotprop.WAIT_10_SEC} seconds
+    Then the ending steps are complete
+
+    # set ABOT configuration
+    Given that I setup S1AP Simulator with default parameters specified in {abotprop.ABOT.EPC.Defaults} on node ABOT
+    Given that I setup S1AP Simulator with USIM parameter "ABOT.UE.USIM.AttachWithImsi=true" on node ABOT
+    # set the value of RES parameter (other than 0x00) manually in Authentication Response message which is sent from UE to MME
+    Given that I setup S1AP Simulator with UE parameter "ABOT.UE.CONFIG.SECURITY.RES=0xFF" on node ABOT
+
+    # Execute ABOT S1AP Simulator
+    When I run S1AP simulator on node ABOT with 1 UE
+
+    Given the execution is paused for {abotprop.WAIT_10_SEC} seconds
+    Given the execution is paused for {abotprop.WAIT_10_SEC} seconds
+
+    # Validate Test Case Execution at Simulator
+    Then I receive S1AP response on node ABOT and verify the presence of all the following values:
+    | responseResult                             | existence               |
+    | Send Attach Request message with IMSI      | {string:nocase:present} |
+    | Received Authentication Request message    | {string:nocase:present} |
+    | Send Authentication Response message       | {string:nocase:present} |
+    | Received Authentication Reject message     | {string:nocase:present} |
+    | Authentication not accepted by the network | {string:nocase:present} |
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+